|
|
“Charge ordering and phase transitions in perovskite manganites: correlation with CMR properties”. Hervieu M, Martin C, Van Tendeloo G, Mercey B, Maignan A, Jirak Z, Raveau B s.l., page 179 (2000).
Keywords: H3 Book chapter; Electron microscopy for materials research (EMAT)
|
|
|
|
“Chemical and structural characterization of oxide precipitates in heavily boron doped silicon by infrared spectroscopy and transmission electron microscopy”. De Gryse O, Clauws P, Vanhellemont J, Lebedev O, van Landuyt J, Simoen E, Claeys C, , 183 (2002)
Abstract: Infrared absorption spectra of oxygen precipitates in boron doped silicon with a boron concentration between 10(17) and 10(19) cm(-3) are analyzed, applying the spectral function theory of the composite precipitates. The aspect ratio of the platelet precipitates has been determined by transmission electron microscopy measurements. Our analysis shows that in samples with moderate doping levels (<10(18) B cm(-3)) SiOgamma precipitates are formed with stoichiometry as in the lightly doped case. In the heavily (>10(18) cm(-3)) boron doped samples, however, the measured spectra of the precipitates are consistent with a mixture of SiO2 and B2O3. with a volume fraction of B2O3 as high as 0.41 in the most heavily doped case.
Keywords: P1 Proceeding; Electron microscopy for materials research (EMAT)
|
|
|
|
“Clustering of vacancies on {113} planes in Si layers close to Si-Si3N4 interfaces and further aggregation of self-interstitials inside vacancy clusters during electron irradiation”. Fedina L, Gutakovskii A, Aseev A, van Landuyt J, Vanhellemont J, Institute of physics conference series
T2 –, Conference on Microscopy of Semiconducting Materials, MAR 22-25, 1999, UNIV OXFORD, OXFORD, ENGLAND , 495 (1999)
Abstract: In situ HREM irradiation of (110) FZ-Si crystals covered with thin Si3N4 films was carried out in a JEOL-4000EX microscope, operated at 400 keV at room temperature. It is found that clustering of vacancies on (113) planes is realised in a Si layer close to the Si-Si3N4 interface at the initial stage of irradiation. Further aggregation of self-interstitials inside vacancy clusters is considered as an alternative way of point defect recombination in extended shape, to be accomplished with the formation of the extended defects of interstitial type upon interstitial supersaturation.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
|
|
|
|
“Conventional and HREM study of structural defects in nanostructured silver halides”. Schryvers D, Goessens C, van Renterghem W, van Landuyt J, de Keyzer R, , 1 (1998)
Keywords: P3 Proceeding; Electron microscopy for materials research (EMAT)
|
|
|
|
“Crystal chemistry of mercury based layered cuprates and oxycarbonates”. Raveau B, Hervieu M, Michel C, Martin C, Maignan A, Van Tendeloo G Narosa, New Delhi, page 132 (1995).
Keywords: H3 Book chapter; Electron microscopy for materials research (EMAT)
|
|
|
|
“The crystal structure of YSr2Cu3O6+x determined by HREM”. Lebedev O, Van Tendeloo G, Marezio M, Licci F, Gilioli E, Gauzzi A, Prodi A s.l., page 877 (2002).
Keywords: H3 Book chapter; Electron microscopy for materials research (EMAT)
|
|
|
|
“Crystal structure of the group of optical materials Ln2MeGe4O12 (Me = Ca, Mn)”. Tarakina NV, Zubkov VG, Leonidov II, Tyutunnik AP, Surat LL, Hadermann J, Van Tendeloo G, Zeitschrift für Kristallographie , 401 (2009). http://doi.org/10.1524/zksu.2009.0059
Abstract: The crystal structure of the group of optical materials Ln2MeGe4O12, Ln = Eu, Gd, Dy-Lu, Y; Me = Ca, Mn and of the solid solution (Y1-xErx)2CaGe4O12 (x = 0 – 1), promising materials for photonics, has been studied in detail. The crystal structure of all compounds exhibit two alternating layers: one formed by Ln and Me atoms and another by cyclic [Ge4O12]8- anions.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Times cited: 7
DOI: 10.1524/zksu.2009.0059
|
|
|
|
“Crystallization of fullerene nanopraticles in an aerosol flow reactor”. Joutsensaari J, Ahonen PP, Tapper U, Kauppinen EI, Pauwels B, Amelinckx S, Van Tendeloo G, (1999)
Keywords: P3 Proceeding; Electron microscopy for materials research (EMAT)
|
|
|
|
“DART explained: how to carry out a discrete tomography reconstruction”. Batenburg KJ, Bals S, Sijbers J, Van Tendeloo G, , 295 (2008)
Keywords: P1 Proceeding; Electron microscopy for materials research (EMAT); Vision lab
|
|
|
|
“Decomposition phenomena in Ni-Mn-Ti austenite”. Schryvers D, Seo JW, Richard O, Vermeulen W, Potapov P s.l., page 887 (1999).
Keywords: H1 Book chapter; Electron microscopy for materials research (EMAT)
|
|
|
|
“Defect induced thickness growth in silver chloride (111) tabular crystals: a TEM study”. Van Renterghem W, Schryvers D, van Landuyt J, Bollen D, Van Roost C, De Keyzer RB, , 38 (2000)
Abstract: Defects in AgG tabular crystals with {111} surfaces are characterised by transmission electron microscopy (TEM) and their influence on the growth process is discussed. In the tabular crystals, twins parallel to the tabular face as well as dislocations along different directions are observed. The twins induce the tabular growth, while the dislocations do not influence the morphology. In 10 to 30% of the crystals that have been characterised, thickness growth is observed and it is shown that in all cases twins on other planes than the tabular ones are present. Two configurations occur more frequently and are analysed in detail. For the first group, twins parallel to the tabular face as well as a microtwin along a non-parallel {111} plane and ending inside the crystal are present. In the crystals of the second group only one extra non-parallel twin occurs giving rise to a bicrystal built up by a tetrahedral shaped part and a flat triangular or trapezoidal part. More complex twin configurations give rise to various, less characteristic morphologies.
Keywords: P1 Proceeding; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
|
|
|
|
“Defect related growth of tabular AgCl(100) crystals: a TEM study”. van Renterghem W, Schryvers D, van Landuyt J, van Roost C, , 389 (1998)
Keywords: P1 Proceeding; Electron microscopy for materials research (EMAT)
|
|
|
|
“Defect structure of Hg-based ceramic superconductors (invited)”. Van Tendeloo G, Hervieu M, Chaillout C, Sciences , 949 (1994)
Keywords: P1 Proceeding; Electron microscopy for materials research (EMAT)
|
|
|
|
“Defects in AgCl and AgBr(100) tabular crystals studied by TEM”. van Renterghem W, Goessens C, Schryvers D, van Landuyt J, Verrept P, Bollen D, van Roost C, de Keyzer R, , 6 (1998)
Keywords: P3 Proceeding; Electron microscopy for materials research (EMAT)
|
|
|
|
Blumenau AT, Frauenheim T, Ö,berg S, Willems B, Van Tendeloo G (2004) Dislocation structures in diamond: density-functional based modelling and high resolution electron microscopy. Trans Tech Publications, s.l
Keywords: MA1 Book as author; Electron microscopy for materials research (EMAT)
|
|
|
|
“Displacive and diffusive components in the formation of the Ni2Al structure studied by HREM, SAED and micro-ED”. Muto S, Merk N, Schryvers D, Tanner LE, Monterey Institute for Advances Studies , 101 (1992)
Keywords: A3 Journal article; Electron microscopy for materials research (EMAT)
|
|
|
|
“Dynamic shear localization in Ti6Al4V”. Peirs J, Verleysen P, Tirry W, Rabet L, Schryvers D, Degrieck J, Procedia Engineering
T2 –, 11th International Conference on the Mechanical Behavior of Materials, (ICM), 2011, Como, ITALY (ICM11) , 1 (2011). http://doi.org/10.1016/j.proeng.2011.04.386
Abstract: The alloy Ti6Al4V is known to be prone to the formation of adiabatic shear bands when dynamically loaded in shear. This causes a catastrophic decrease of the load carrying capacity and is usually followed by fracture. Although, the main mechanism is recognized to be the competition between strain hardening and thermal softening, a detailed understanding of the role of microstructural plasticity mechanisms and macroscopic loading conditions does not exist yet. To study strain localization and shear fracture, different high strain rate shear tests have been carried out: compression of hat-shaped specimens, torsion of thin walled tubular specimens and in-plane shear tests. The value of the three techniques in studying shear localization is evaluated. Post-mortem analysis of the fracture surface and the materials' microstructure is performed with optical and electron microscopy. In all cases a ductile fracture is observed. SEM and TEM techniques are used to study the local microstructure and composition in the shear band and as such the driving mechanism for the ASB formation. (C) 2011 Published by Elsevier Ltd. Selection and/or peer-review under responsibility of ICM11
Keywords: P1 Proceeding; Electron microscopy for materials research (EMAT)
Times cited: 4
DOI: 10.1016/j.proeng.2011.04.386
|
|
|
|
“Effect of selenium content of CuInSex alloy nanopowder precursors on recrystallization of printed CuInSe2 absorber layers during selenization heat treatment”. E Zaghi A, Buffière M, Koo J, Brammertz G, Batuk M, Verbist C, Hadermann J, Kim WK, Meuris M, Poortmans J, Vleugels J;, Thin solid films : an international journal on the science and technology of thin and thick films , 1 (2014). http://doi.org/10.1016/j.tsf.2014.10.003
Abstract: Polycrystalline CuInSe2 semiconductors are efficient light absorber materials for thin film solar cell technology, whereas printing is one of the promising low cost and non-vacuum approaches for the fabrication of thin film solar cells. The printed precursors are transformed into a dense polycrystalline CuInSe2 semiconductor film via thermal treatment in ambient selenium atmosphere (selenization). In this study, the effect of the selenium content in high purity mechanically synthesized CuInSex (x = 2, 1.5, 1 or 0.5) alloy precursors on the recrystallization of the CuInSe2 phase during the selenization process was investigated. The nanostructure and phase variation of CuInSex nanopowders were investigated by different characterization techniques. The recrystallization process of the 12 μm thick CuInSex coatings into the CuInSe2 phase during selenization in selenium vapor was investigated via in-situ high temperature X-ray diffraction. The CuInSex precursors with lower selenium content showed a more pronounced phase conversion into CuInSe2 compared to the higher selenium content CuInSex precursors. Moreover, the CuInSex (x = 0.5 and 1) precursor resulted in a denser polycrystalline CuInSe2 semiconductor film with larger crystals. This could be attributed to a more intensive atomic interdiffusion within the CuInSex precursor system compared to a CuInSe2 phase precursor, and the formation of intermediate CuSe and CuSe2 fluxing phases during selenization.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 1.879
Times cited: 7
DOI: 10.1016/j.tsf.2014.10.003
|
|
|
|
“EFTEM study of plasma etched low-k Si-O-C dielectrics”. Hens S, Bender H, Donaton RA, Maex K, Vanhaelemeersch S, van Landuyt J, Institute of physics conference series
T2 –, Royal-Microscopical-Society Conference on Microscopy of Semiconducting, Materials, MAR 25-29, 2001, UNIV OXFORD, OXFORD, ENGLAND , 415 (2001)
Abstract: Materials with low dielectric constant ("low-k'') in combination with Cu metallization are replacing the oxide based dielectrics with Al metallization in future generations of micro-electronic devices. In this work, a carbon doped oxide low-k dielectric material is studied after different kinds of etch/strip steps in single damascene Cu. filled line structures. Interline capacitance measurements indicate a dependence of the dielectric constant on the strip conditions. EFTEM is used to study the composition of the dielectric material and the modification of the low-k material at the sidewall of the etched structures for the various treatment conditions.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
|
|
|
|
“Electron diffraction and microscopy of single-walled carbon nanotube bundles”. Colomer J-F, Van Tendeloo G Kluwer, Boston, Mass., page 45 (2003).
Keywords: H3 Book chapter; Electron microscopy for materials research (EMAT)
|
|
|
|
“Electron diffraction of nanotubes bundles : unique helicity and tube-tube atomically coherent packing”. Colomer J-F, Henrard L, Lambin P, Van Tendeloo G, AIP conference proceedings
T2 –, 16th International Winterschool on Electronic Properties of Novel, Materials, MAR 02-09, 2002, KIRCHBERG, AUSTRIA , 314 (2002). http://doi.org/10.1063/1.1514131
Abstract: The atomic structure of single-wall carbon nanotube bundles produced by three different techniques has been characterized by electron diffraction and microscopy. Small bundles produced by Catalytical Chemical Vapor Deposition (CCVD) exhibit only one or two tube chiralities within a single bundle while bundles produced by arc-discharge or laser-ablation exhibit more chiralities. A detailed analysis of the central line of diffraction is also presented. The CCVD nanotubes present more intense spots around 1.7 Angstrom(-1) < k < 2Angstrom(-1) (k is the momentum transfer) compared to what is observed for nanotubes produced by other methods. Amongst the possible explanation for such an anomaly, we put forward that in this range of momentum transfer, the relative tube orientations and translations are important for what concerns the interpretation of the diffraction peaks intensities.
Keywords: P1 Proceeding; Electron microscopy for materials research (EMAT)
DOI: 10.1063/1.1514131
|
|
|
|
Lu Y (2013) Electron energy-loss spectroscopy (EELS) characterization of diamond and related materials. Antwerpen
Keywords: Doctoral thesis; Electron microscopy for materials research (EMAT)
|
|
|
|
“Electron microscopic study of long period ordering in complex oxides”. Amelinckx S, Nistor LC, Van Tendeloo G s.l., page 1 (1994).
Keywords: H3 Book chapter; Electron microscopy for materials research (EMAT)
|
|
|
|
“Electron-microscopy and the structural studies of superconducting materials and fullerites”. Van Tendeloo G, Amelinckx S, NATO Advanced Study Institutes series: series E : applied sciences
T2 –, NATO Advanced Study Institute on Materials and crystallographic Aspects, of HT(c)-Superconductivity, May 17-30, 1993, Erice, Italy , 521 (1994)
Keywords: P1 Proceeding; Electron microscopy for materials research (EMAT)
|
|
|
|
“Electron microscopy of fullerenes and fullerene related structures”. Van Tendeloo G, van Landuyt J, Amelinckx S, , 498 (1994)
Keywords: P3 Proceeding; Electron microscopy for materials research (EMAT)
|
|
|
|
“Electron microscopy of fullerenes and related materials”. Van Tendeloo G, Amelinckx S Wiley-VCH, Weinheim, page 353 (2000).
Keywords: H3 Book chapter; Electron microscopy for materials research (EMAT)
|
|
|
|
“Electron microscopy of interfaces in new materials”. Van Tendeloo G, Goessens C, Schryvers D, van Haverbergh J, de Veirman A, van Landuyt J s.l., page 200 (1991).
Keywords: H3 Book chapter; Electron microscopy for materials research (EMAT)
|
|
|
|
“Electron microscopy of C60 and C70 fullerites”. Van Tendeloo G, Amelinckx S Springer, Berlin, page 182 (1993).
Keywords: H3 Book chapter; Electron microscopy for materials research (EMAT)
|
|
|
|
“Electron microscopy on nanoparticles: structure of C60 and C70 nanopraticles”. Pauwels B, Van Tendeloo G, Joutsensaari J, Kauppinen EI, (1999)
Keywords: P3 Proceeding; Electron microscopy for materials research (EMAT)
|
|
|
|
Amelinckx S, van Dyck D, van Landuyt J, Van Tendeloo G (1997) Electron microscopy: principles and fundamentals. Vch, Weinheim
Keywords: ME1 Book as editor or co-editor; Electron microscopy for materials research (EMAT); Vision lab
|
|
