“Effects of IR heating on distribution and transport of gaseous air pollutants in urban and mountain churches in Poland”. Bencs L, Spolnik Z, Worobiec A, Samek L, Jutte BAHG, Van Grieken R, Journal of cultural heritage 36, 200 (2019). http://doi.org/10.1016/J.CULHER.2018.09.007
Abstract: The spatial distribution and temporal concentration variation of a set of gaseous air components (e.g., CO2, CO, H2CO, H2O) have been monitored with a multi-channel photoacoustic gas-analyzer in an urban church ( Saint Catherine's, Cracow) and a mountain church ( Saint Michaels Archangel, Szalowa) of Poland, in order to assess the likely effects of air pollution indoors under the influence of provisory electrical infrared (IR) heaters and without heating. Likewise, the ventilation characteristic and the leakage of these buildings with different constructions (i.e., plastered stone and wooden structures) with the assistance of decay curves of SF6 tracer gas was evaluated and compared. The wooden building in Szalowa, due to its more open structure, developed about one order higher ventilation rates (e.g., 0.9-1.3 h(-1)) than the stone church in Cracow (e.g., 0.1 h(-1)). The IR-heating affected only modestly the ventilation rate of the wooden church (e.g., 1.2-1.6 h(-1)), but it increased significantly that of the plastered stone church (e.g., 0.27 h(-1)). The ventilation rates were also assessed with the use of the CO2 curve decay method, and satisfactory agreement was found with those observed by the use of SF6 tracer. The spatial distribution of the studied gaseous pollutants (CO2, H2O) was found to be in some occasions nonhomogeneous in both buildings, due to the active usage of the IR-heating, especially, during a couple of consecutive liturgical services. Besides the pollution events due to ingress of gaseous air pollutants, present at enhanced levels outdoors, increased CO, CO2 and H2CO peaks were observed indoors too, which, in most cases, could be associated with incense burning. (C) 2018 Elsevier Masson SAS. All rights reserved.
Keywords: A1 Journal article; Art; History; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation); Laboratory Experimental Medicine and Pediatrics (LEMP)
DOI: 10.1016/J.CULHER.2018.09.007
|
“Corrosion protection of Cu by atomic layer deposition”. Cremers V, Rampelberg G, Baert K, Abrahami S, Claes N, de Oliveira TM, Terryn H, Bals S, Dendooven J, Detavernier C, Journal of vacuum science and technology: A: vacuum surfaces and films 37, 060902 (2019). http://doi.org/10.1116/1.5116136
Abstract: Atomic layer deposition (ALD) is a vapor phase technique that is able to deposit uniform, conformal thin films with an excellent thickness control at the atomic scale. 18 nm thick Al2O3 and TiO2 coatings were deposited conformaly and pinhole-free onto micrometer-sized Cu powder, using trimethylaluminum and tetrakis(dimethylamido)titanium(IV), respectively, as a precursor and de-ionized water as a reactant. The capability of the ALD coating to protect the Cu powder against corrosion was investigated. Therefore, the stability of the coatings was studied in solutions with different pH in the range of 0–14, and in situ raman spectroscopy was used to detect the emergence of corrosion products of Cu as an indication that the protective coating starts to fail. Both ALD coatings provide good protection at standard pH values in the range of 5–7. In general, the TiO2 coating shows a better barrier protection against corrosion than the Al2O3 coating. However, for the most extreme pH conditions, pH 0 and pH 14, the TiO2 coating starts also to degrade.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 1.374
Times cited: 7
DOI: 10.1116/1.5116136
|
“Large variation in temperature dependence of band-to-band tunneling current in tunnel devices”. Bizindavyi J, Verhulst AS, Verreck D, Sorée B, Groeseneken G, IEEE electron device letters 40, 1864 (2019). http://doi.org/10.1109/LED.2019.2939668
Abstract: The observation of a significant temperature-dependent variation in the ${I}$ – ${V}$ characteristics of tunneling devices is often interpreted as a signature of a trap-assisted-tunneling dominated current. In this letter, we use a ballistic 2D quantum-mechanical simulator, calibrated using the measured temperature-dependent ${I}$ – ${V}$ characteristics of Esaki diodes, to demonstrate that the temperature dependence of band-to-band tunneling (BTBT) current can vary significantly in both Esaki diodes and tunnel FETs. The variation of BTBT current with temperature is impacted by doping concentration, gate voltage, possible presence of a highly-doped pocket at the tunnel junction, and material.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 3.048
DOI: 10.1109/LED.2019.2939668
|
“De combinatie werk-gezin en het gebruik van formele kinderopvang bij vrouwen met een migratieachtergrond : een mixed methods-benadering”. Wood J, Geerts R, Majean L, Coene V, Vanheeswijck J, de Smalen D, Ronda T, Keizer K, Sociologos (Brussel) 40, 123 (2019)
Keywords: A1 Journal article; Sociology; Centre for Population, Family and Health; Sustainable Energy, Air and Water Technology (DuEL); Centre for Research on Environmental and Social Change
|
“Combined effects of blockage and yield stress on drag and heat transfer from an in-line array of three spheres”. Dasgupta N, Borah R, Mishra P, Gupta AK, Chhabra RP, Journal of dispersion science and technology 40, 855 (2019). http://doi.org/10.1080/01932691.2018.1485581
Abstract: This work reports results on the drag and heat transfer from an in-line array of three isothermal spheres falling in a cylindrical confinement filled with Bingham plastic fluids. The effects of dimensionless parameters, such as the Reynolds number (1 ≤ Re ≤ 100), Prandtl number (1 ≤ Pr ≤ 100), Bingham number (0 ≤ Bn ≤ 100), blockage ratio (2 ≤ β ≤ 4) and sphere-to-sphere distance (1.5 ≤ t ≤ 6) have been elucidated. The flow and heat transfer characteristics were analysed in terms of yielded/unyielded regions, streamline and isotherm contours, drag coefficient, pressure coefficient, and local and average Nusselt number. Broadly, the drag coefficient shows a positive dependence on Bn and sphere-to-sphere distance (t) while it exhibits an inverse dependence on Re and β. On the other hand, the Nusselt number shows a positive dependence on Re, Pr, Bn and β; and a complex dependence on t for each sphere. Simple predictive expressions for the average Nusselt number for each sphere are formulated, thereby enabling its prediction in a new application.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1080/01932691.2018.1485581
|
“MA-XRF imaging as a tool to characterize the 16th century heraldic stained-glass panels in Ghent Saint Bavo Cathedral”. Legrand S, van der Snickt G, Cagno S, Caen J, Janssens K, Journal of cultural heritage 40, 163 (2019). http://doi.org/10.1016/J.CULHER.2019.06.003
Abstract: MA-XRF is a novel macroscopic imaging technique originally developed for easel paintings and recently made available to glass conservators. This paper discusses the first real-life contribution of MA-XRF imaging to a conservation intervention of stained-glass panels. The six panels under study belong to the cathedral building since their creation in 1555-1559 AD. MA-XRF appeared an outstanding tool for first-line screening of stained-glass windows, providing readily interpretable information on glass type, coloring and alteration processes. In particular, the chemical imaging technique allowed distinguishing unambiguously the surviving original glass panes from later additions, thereby ensuring a correct historical understanding. From a more practical point of view, the experiments supplied accurate schemes that can be directly incorporated in condition reports and assist designing the ensuing conservation approach. (C0 2019 Elsevier Masson SAS. All rights reserved.
Keywords: A1 Journal article; Art; History; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation); Antwerp Cultural Heritage Sciences (ARCHES)
DOI: 10.1016/J.CULHER.2019.06.003
|
“Nonlinear dispersive model of electroporation for irregular nucleated cells”. Chiapperino MA, Bia P, Caratelli D, Gielis J, Mescia L, Dermol-Cerne J, Miklavcic D, Bioelectromagnetics 40, 331 (2019). http://doi.org/10.1002/BEM.22197
Abstract: In this work, the electroporation phenomenon induced by pulsed electric field on different nucleated biological cells is studied. A nonlinear, non-local, dispersive, and space-time multiphysics model based on Maxwell's and asymptotic Smoluchowski's equations has been developed to calculate the transmembrane voltage and pore density on both plasma and nuclear membrane perimeters. The irregular cell shape has been modeled by incorporating in the numerical algorithm the analytical functions pertaining to Gielis curves. The dielectric dispersion of the cell media has been modeled considering the multi-relaxation Debye-based relationship. Two different irregular nucleated cells have been investigated and their response has been studied applying both the dispersive and non-dispersive models. By a comparison of the obtained results, differences can be highlighted confirming the need to make use of the dispersive model to effectively investigate the cell response in terms of transmembrane voltages, pore densities, and electroporation opening angle, especially when irregular cell shapes and short electric pulses are considered. Bioelectromagnetics. 2019;40:331-342. (c) 2019 Wiley Periodicals, Inc.
Keywords: A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1002/BEM.22197
|
“Urine nitrification with a synthetic microbial community”. Christiaens MER, De Paepe J, Ilgrande C, De Vrieze J, Barys J, Teirlinck P, Meerbergen K, Lievens B, Boon N, Clauwaert P, Vlaeminck SE, Systematic and applied microbiology 42, Unsp 126021 (2019). http://doi.org/10.1016/J.SYAPM.2019.126021
Abstract: During long-term extra-terrestrial missions, food is limited and waste is generated. By recycling valuable nutrients from this waste via regenerative life support systems, food can be produced in space. Astronauts' urine can, for instance, be nitrified by micro-organisms into a liquid nitrate fertilizer for plant growth in space. Due to stringent conditions in space, microbial communities need to be be defined (gnotobiotic); therefore, synthetic rather than mixed microbial communities are preferred. For urine nitrification, synthetic communities face challenges, such as from salinity, ureolysis, and organics. In this study, a synthetic microbial community containing an AOB (Nitrosomonas europaea), NOB (Nitrobacter winogradskyi), and three ureolytic heterotrophs (Pseudomonas fluorescens, Acidovorax delafieldii, and Delftia acidovorans) was compiled and evaluated for these challenges. In reactor 1, salt adaptation of the ammonium-fed AOB and NOB co-culture was possible up to 45 mS cm(-1), which resembled undiluted nitrified urine, while maintaining a 44 +/- 10 mg NH4+-N L-1 d(-1) removal rate. In reactor 2, the nitrifiers and ureolytic heterotrophs were fed with urine and achieved a 15 +/- 6 mg NO3--N L-1 d(-1) production rate for 1% and 10% synthetic and fresh real urine, respectively. Batch activity tests with this community using fresh real urine even reached 29 +/- 3 mg N L-1 d(-1). Organics removal in the reactor (69 +/- 15%) should be optimized to generate a nitrate fertilizer for future space applications. (C) 2019 Elsevier GmbH. All rights reserved.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1016/J.SYAPM.2019.126021
|
“Novel phenyl-substituted pyrazinoporphyrazine complexes of rare-earth elements : optimized synthetic protocols and physicochemical properties”. Kosov AD, Dubrinina TV, Borisova NE, Ivanov AV, Drozdov KA, Trashin SA, De Wael K, Kotova MS, Tomilova LG, New journal of chemistry 43, 3153 (2019). http://doi.org/10.1039/C8NJ05939J
Abstract: Novel synthetic protocols based on both template and multi-step methods were developed for phenyl-substituted pyrazinoporphyrazine complexes of rare-earth elements (Y, Eu, Gd, Dy, Er and Lu). p-Hydroquinone was employed as a reaction medium and as a reducing agent in the process of porphyrazine macrocycle formation. Both thermal and microwave irradiation techniques were successfully applied for activation of the template macrocyclization process. An alternative multi-step approach involving the initial stage of free-base ligand formation was realized for the lutetium compound. The target complexes were identified by high-resolution mass spectrometry, infrared spectroscopy and nuclear magnetic resonance (NMR) spectroscopy. Electrochemical behavior in solution and UV-vis absorbance in solutions and films were studied as well. Shifts in the position of the Q band and oxidationreduction potentials in comparison with corresponding phthalocyanine analogues were noticed. Using the IR absorption spectra recorded in the temperature range of 170300 K, the position of the Fermi level of −4.7 ± 0.1 eV and a characteristic energy diagram were obtained for the erbium complex.
Keywords: A1 Journal article; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation)
Impact Factor: 3.269
Times cited: 1
DOI: 10.1039/C8NJ05939J
|
“De kleine boerderij : twee bijzondere tuinkamers”. Vermander C, De Wael J, Gielis J, Groencontact 45, 14 (2019)
Keywords: A2 Journal article; Sustainable Energy, Air and Water Technology (DuEL)
|
“Rational design of an XNA ligase through docking of unbound nucleic acids to toroidal proteins”. Vanmeert M, Razzokov J, Mirza MU, Weeks SD, Schepers G, Bogaerts A, Rozenski J, Froeyen M, Herdewijn P, Pinheiro VB, Lescrinier E, Nucleic acids research 47, 7130 (2019). http://doi.org/10.1093/nar/gkz551
Abstract: Xenobiotic nucleic acids (XNA) are nucleic acid analogues not present in nature that can be used for the storage of genetic information. In vivo XNA applications could be developed into novel biocontainment strategies, but are currently limited by the challenge of developing XNA processing enzymes such as polymerases, ligases and nucleases. Here, we present a structure-guided modelling-based strategy for the rational design of those enzymes essential for the development of XNA molecular biology. Docking of protein domains to unbound double-stranded nucleic acids is used to generate a first approximation of the extensive interaction of nucleic acid processing enzymes with their substrate. Molecular dynamics is used to optimise that prediction allowing, for the first time, the accurate prediction of how proteins that form toroidal complexes with nucleic acids interact with their substrate. Using the Chlorella virus DNA ligase as a proof of principle, we recapitulate the ligase's substrate specificity and successfully predict how to convert it into an XNA-templated XNA ligase.
Keywords: A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Impact Factor: 10.162
Times cited: 1
DOI: 10.1093/nar/gkz551
|
“Highly porous palladium nanodendrites : wet-chemical synthesis, electron tomography and catalytic activity”. Mourdikoudis S, Montes-Garcia V, Rodal-Cedeira S, Winckelmans N, Perez-Juste I, Wu H, Bals S, Perez-Juste J, Pastoriza-Santos I, Journal of the Chemical Society : Dalton transactions 48, 3758 (2019). http://doi.org/10.1039/C9DT00107G
Abstract: A simple procedure to obtain highly porous hydrophilic palladium nanodendrites in one-step is described. The synthetic strategy is based on the thermal reduction of a Pd precursor in the presence of a positively charged polyelectrolyte such as polyethylenimine (PEI). Advanced electron microscopy techniques combined with X-ray diffraction (XRD), thermogravimetry and BET analysis demonstrate the polycrystalline nature of the nanodendrites as well as their high porosity and active surface area, facilitating a better understanding of their unique morphology. Besides, catalytic studies performed using Raman scattering and UV-Vis spectroscopies revealed that the nanodendrites exhibit a superior performance as recyclable catalysts towards hydrogenation reaction compared to other noble metal nanoparticles.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Times cited: 23
DOI: 10.1039/C9DT00107G
|
“Interpreting technical evidence from spectral imaging of paintings by Edouard Manet in the Courtauld Gallery”. Amato SR, Burnstock A, Cross M, Janssens K, Rosi F, Cartechini L, Fontana R, Dal Fovo A, Paolantoni M, Grazia C, Romani A, Michelin A, Andraud C, Tournie A, Dik J, X-ray spectrometry
T2 –, MA-XRF Workshop on Developments and Applications of Macro-XRF in, Conservation, Art, and Archeology, SEP 24-25, 2017, Trieste, ITALY 48, 282 (2019). http://doi.org/10.1002/XRS.2828
Abstract: The paintings by edouard Manet in The Courtauld Gallery Dejeuner sur l'herbe (1863-68), Marguerite de Conflans en Toilette de Bal (1870-1880), Banks of the Seine at Argenteuil (1874), and A Bar at the Folies-Bergere (1882) were investigated for the first time using a range of non-invasive in situ analyses. The aims of the study were to investigate the painting techniques and materials used for this group of works and to critically evaluate the technical evidence derived from the integrated use of imaging techniques and portable spectroscopic methods in this context. The paintings were investigated by means of macro X-ray fluorescence (MA-XRF), reflection spectral imaging, portable UV-Vis-NIR spectroscopy, portable Raman spectroscopy, and reflection FTIR. MA-XRF and reflection spectral imaging allowed visualising elements in the compositions that were not visible using traditional methods of technical study. For example, MA-XRF analysis of Dejeuner sur l'herbe revealed elements of the development of the composition that provided new evidence to consider its relationship to other versions of the composition. The study also highlighted questions about the interpretation of elemental distribution maps and spectral images that did not correspond to the reworking visible in X-radiographs. For example, in A Bar at the Folies-Bergere Manet made numerous changes during painting, which were not clearly visualised with any of the techniques used. The research has wider implications for the study of Impressionist paintings, as the results will support technical studies of works by other artists of the period who used similar materials and painting methods.
Keywords: A1 Journal article; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation)
Impact Factor: 1.298
DOI: 10.1002/XRS.2828
|
“Preface to the special issue on: MA-XRF “developments and applications of macro-XRF in conservation, art, and archeology&rdquo, (Trieste, Italy, 24 and 25 September 2017)”. Romano FP, Janssens K, X-ray spectrometry 48, 249 (2019). http://doi.org/10.1002/XRS.3047
Keywords: Editorial; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation)
Impact Factor: 1.298
DOI: 10.1002/XRS.3047
|
“In vitro and ex vivo assessment of microporous Faujasite zeolite (NaX-FAU) as a carrier for the oral delivery of danazol”. Kontogiannidou E, Karavasili C, Kouskoura MG, Filippousi M, Van Tendeloo G, Andreadis II, Eleftheriadis GK, Kontopoulou I, Markopoulou CK, Bouropoulos N, Fatouros DG, Journal of drug delivery science and technology 51, 177 (2019). http://doi.org/10.1016/J.JDDST.2019.02.036
Abstract: Microporous zeolite NaX-FAU has been systemically evaluated for the oral delivery of the poorly water-soluble compound danazol. For this purpose, danazol-loaded zeolitic particles were prepared by the incipient wetness method and were characterized by means of N-2 physisorption, X-ray diffraction (XRD), differential scanning calorimetry (DSC), thermogravimetric analysis (TGA) and high-resolution transmission electron microscopy (HRTEM). The zeolitic formulation shows a high drug payload and drug stability over a period of six months under accelerated storage conditions. The dissolution profile of danazol-loaded zeolitic particles was assessed in simulated gastric fluid (SGF) pH 1.2; fasted state simulated intestinal fluids (FaSSIF) and fed state simulated intestinal fluid (FeSSIF) showing a gradual and increasing drug dissolution in the different media. Ex vivo studies using the everted gut sac model show an increased drug transport across rat intestinal epithelium when loaded in the zeolitic particles. Our results suggest that microporous Faujasite zeolite (NaX-FAU) could be used as a drug delivery system to facilitate the oral delivery of poorly water soluble compounds.
Keywords: A1 Journal article; Pharmacology. Therapy; Electron microscopy for materials research (EMAT)
Impact Factor: 1.194
Times cited: 3
DOI: 10.1016/J.JDDST.2019.02.036
|
“Characterization of a nitrogen gliding arc plasmatron using optical emission spectroscopy and high-speed camera”. Gröger S, Ramakers M, Hamme M, Medrano JA, Bibinov N, Gallucci F, Bogaerts A, Awakowicz P, Journal of physics: D: applied physics 52, 065201 (2019). http://doi.org/10.1088/1361-6463/aaefe4
Abstract: A gliding arc plasmatron (GAP), which is very promising for purification and gas conversion,
is characterized in nitrogen using optical emission spectroscopy and high-speed photography,
because the cross sections of electron impact excitation of N 2 are well known. The gas
temperature (of about 5500 K), the electron density (up to 1.5 × 10 15 cm −3 ) and the reduced
electric field (of about 37 Td) are determined using an absolutely calibrated intensified charge-
coupled device (ICCD) camera, equipped with an in-house made optical arrangement for
simultaneous two-wavelength diagnostics, adapted to the transient behavior of a GA channel
in turbulent gas flow. The intensities of nitrogen molecular emission bands, N 2 (C–B,0–0) as
well as N +
2 (B–X,0–0), are measured simultaneously. The electron density and the reduced
electric field are determined at a spatial resolution of 30 µm, using numerical simulation and
measured emission intensities, applying the Abel inversion of the ICCD images. The temporal
behavior of the GA plasma channel and the formation of plasma plumes are studied using a
high-speed camera. Based on the determined plasma parameters, we suggest that the plasma
plume formation is due to the magnetization of electrons in the plasma channel of the GAP by
an axial magnetic field in the plasma vortex.
Keywords: A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Impact Factor: 2.588
Times cited: 7
DOI: 10.1088/1361-6463/aaefe4
|
“Coupling of the skyrmion velocity to its breathing mode in periodically notched nanotracks”. Leliaert J, Gypens P, Milošević, MV, Van Waeyenberge B, Mulkers J, Journal of physics: D: applied physics 52, 024003 (2019). http://doi.org/10.1088/1361-6463/AAE7C1
Abstract: A thorough understanding of the skyrmion motion through nanotracks is a prerequisite to realize the full potential of spintronic applications like the skyrmion racetrack memory. One of the challenges is to place the data, i.e. skyrmions, on discrete fixed positions, e.g. below a read or write head. In the domain-wall racetrack memory, one proposed solution to this problem was patterning the nanotrack with notches. Following this approach, this paper reports on the skyrmion mobility through a nanotrack with periodic notches (constrictions) made using variations in the chiral Dzyaloshinskii-Moriya interaction. We observe that such notches induce a coupling between the mobility and the skyrmion breathing mode, which manifests itself as velocity-dependent oscillations of the skyrmion diameter and plateaus in which the velocity is independent of the driving force. Despite the fact that domain walls are far more rigid objects than skyrmions, we were able to perform an analogous study and, surprisingly, found even larger plateaus of constant velocity. For both systems it is straightforward to tune the velocity at these plateaus by changing the design of the notched nanotrack geometry, e.g. by varying the distance between the notches. Therefore, the notch-induced coupling between the excited modes and the mobility could offer a strategy to stabilize the velocity against unwanted perturbations in racetrack-like applications. In the last part of the paper we focus on the low-current mobility regimes, whose very rich dynamics at nonzero temperatures are very similar to the operating principle of recently developed probabilistic logic devices. This proves that the mobility of nanomagnetic structures through a periodically modulated track is not only interesting from a fundamental point of view, but has a future in many spintronic applications.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 2.588
Times cited: 10
DOI: 10.1088/1361-6463/AAE7C1
|
“Etching induced formation of interfacial FeMn in IrMn/CoFe bilayers”. O'Donnell D, Hassan S, Du Y, Gauquelin N, Krishnan D, Verbeeck J, Fan R, Steadman P, Bencok P, Dobrynin AN, Journal of physics: D: applied physics 52, 165002 (2019). http://doi.org/10.1088/1361-6463/AB03BD
Abstract: The effect of ion etching on exchange bias in IrMn3/Co70Fe30 bilayers is investigated. In spite of the reduction of saturation magnetization caused by the embedding of Tr from the capping layer into the Co70Fe30 layer during the etching process, the exchange bias in samples with the same thickness of the Co70Fe30 layer is reducing in proportion to the etching power. X-ray magnetic circular dichroism measurements revealed the emergence of an uncompensated Mn magnetization after etching, which is antiferromagnetically coupled to the ferromagnetic layer. This suggests etching induced formation of small interfacial FeMn regions which leads to the decrease of effective exchange coupling between ferromagnetic and antiferromagnetic layers.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 2.588
DOI: 10.1088/1361-6463/AB03BD
|
“Effect of dust particle size on the plasma characteristics in a radio frequency capacitively coupled silane plasma”. Jia W-Z, Zhang Q-Z, Wang X-F, Song Y-H, Zhang Y-Y, Wang Y-N, Journal of physics: D: applied physics 52, 015206 (2019). http://doi.org/10.1088/1361-6463/AAE5CF
Abstract: Compared with dust-free plasmas, the existence of dust particles in plasmas may greatly influence the plasma properties. such as the plasma density, electron temperature, sheath properties, electron energy distribution function (EEDF) as well as the heating mechanism. In this work, a 1D hybrid fluid/MC model has been developed to investigate the interaction between dust and plasma in a low-pressure silane discharge sustained in a radio frequency capacitively coupled plasma, in which we assume spherical dust particles with a given radius are generated by taking the sum of the production rate of Si2H4- and Si2H5- as the nucleation rate. From our simulation, the plasma may experience definite perturbation by dust particles with a certain radius (more than 50nm) with an increase in electron temperature first, which further induces a rapid rise in the positive and negative ion densities. Then, the densities begin to decline due to the gradual lack of sufficient seed electrons. In addition, as the dust radius increases, the high energy tails of the EEDFs will be enhanced for discharge maintenance, accompanied by a decline in the population of low-energy electrons in comparison with those of pristine plasma. Furthermore, an obvious bulk heating is observed apart from the a-mode and local field reversal heating. This may contribute to the enhanced bulk electric field (also called the drift field) as a result of electron depletion via the dust. In addition, large-sized dust particles that accumulate near the sheaths tend to form two stable density peaks with their positions largely influenced by the time-averaged sheath thickness. A detailed study of the effects of the external parameters, including pressure, voltage and frequency, on the spatial distribution of dust particles is also conducted.
Keywords: A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Impact Factor: 2.588
DOI: 10.1088/1361-6463/AAE5CF
|
“Dissecting demand response : a quantile analysis of flexibility, household attitudes, and demographics”. Srivastava A, Van Passel S, Laes E, Energy Research and Social Science 52, 169 (2019). http://doi.org/10.1016/J.ERSS.2019.02.011
Abstract: Demand response (DR) can aid with grid integration of renewables, ensuring security of supply, and reducing generation costs. However, not enough is known about how residential customers’ perceptions of DR shape their response to such programs. This paper offers a deeper understanding of – and reveals the heterogeneity in – this relationship by conducting a quantile regression analysis of a Belgian DR trial, combining data on response with information on household attitudes towards smart appliances. Results overall suggest that improving response requires subtle shifts in electricity consumption behaviour, which can be achieved through changes in user perceptions. Specifically, if customers are inclined to be flexible, a stronger perception of smart appliances as being beneficial can greatly improve response. With those who are less flexible, the cost of smart appliances is a bigger concern. Thus, when designing DR programs, policymakers should aim to promote modest behaviour changes – so as to minimise inconvenience – in customers, by improving awareness on the benefits of smart appliances. Uptake of such DR programs may be improved by explaining the financial benefits or offering incentives to less flexible population segments. Lastly, improving response among older population segments will require a deeper investigation into their concerns.
Keywords: A1 Journal article; Economics; Engineering Management (ENM)
Times cited: 1
DOI: 10.1016/J.ERSS.2019.02.011
|
“Non-thermal plasma-induced immunogenic cell death in cancer”. Khalili M, Daniels L, Lin A, Krebs FC, Snook AE, Bekeschus S, Bownel WB, Miller V, Journal of physics: D: applied physics 52, 423001 (2019). http://doi.org/10.1088/1361-6463/AB31C1
Abstract: Recent advances in biomedical research in cancer immunotherapy have identified the use of an oxidative stress-based approach to treat cancers, which works by inducing immunogenic cell death (ICD) in cancer cells. Since the anti-cancer effects of non-thermal plasma (NTP) are largely attributed to the reactive oxygen and nitrogen species that are delivered to and generated inside the target cancer cells, it is reasonable to postulate that NTP would be an effective modality for ICD induction. NTP treatment of tumors has been shown to destroy cancer cells rapidly and, under specific treatment regimens, this leads to systemic tumorspecific immunity. The translational benefit of NTP for treatment of cancer relies on its ability to enhance the interactions between NTP-exposed minor cells and local immune cells which initiates subsequent protective immune responses. This review discusses results from recent investigations of NTP application to induce ICD in cancer cells. With further optimization of clinical devices and treatment protocols, NTP can become an essential part of the therapeutic armament against cancer.
Keywords: A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Impact Factor: 2.588
Times cited: 6
DOI: 10.1088/1361-6463/AB31C1
|
“Conserving African biosphere reserves : a workshop on the valuation of ecosystem services in Man and the Biosphere Reserves”. Janssens de Bisthoven L, Rochette A-J, Verheyen E, Akpona TJ-D, Verbist B, Vanderhaegen K, Naturinda Z, Van Passel S, Berihun D, Munishi L, Hugé, J, Oryx 53, 609 (2019). http://doi.org/10.1017/S003060531900070X
Keywords: A1 Journal article; Engineering Management (ENM); Evolutionary ecology group (EVECO)
Impact Factor: 2.191
DOI: 10.1017/S003060531900070X
|
“Study of the Q&prime, (Q)-phase precipitation in Al–Mg–Si–Cu alloys by quantification of atomic-resolution transmission electron microscopy images and atom probe tomography”. Ding L, Orekhov A, Weng Y, Jia Z, Idrissi H, Schryvers D, Muraishi S, Hao L, Liu Q, Journal of materials science 54, 7943 (2019). http://doi.org/10.1007/s10853-019-03427-6
Abstract: The precipitation mechanism of the Q phase in Al-Mg-Si-Cu alloys has long been the subject of ambiguity and debate since its metastable phase (Q 0) has the same crystal structure and similar lattice parameters as its equilibrium counterparts. In the present work, the evolution of the Q 0 (Q) phase during aging is studied by combination of quantitative atomic-resolution scanning transmission electron microscopy and atom probe tomography. It was found that the transformation from the Q 0 to the Q phase involves changes of the occupancy of Al atoms in atomic columns of the Q 0 (Q) phase. The Al atoms incorporated in the Cu, Si and Mg columns are gradually released into the Al matrix, while mixing between Cu and Si atoms occurs in the Si columns. This transformation process is mainly attributed to the low lattice misfit of the equilibrium Q phase. Besides, the formation of various compositions of the Q phase is due to the different occupancy in the atomic columns of the Q phase. The occupancy changes in the columns of the Q phase are kinetically controlled and are strongly influenced by the alloy composition and aging temperature.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 2.599
Times cited: 1
DOI: 10.1007/s10853-019-03427-6
|
“Layered CeSO and LiCeSO oxide chalcogenides obtained via topotactic oxidative and reductive transformations”. Cassidy SJ, Pitcher MJ, Lim JJK, Hadermann J, Allen JP, Watson GW, Britto S, Chong EJ, Free DG, Grey CP, Clarke SJ, Inorganic chemistry 58, 3838 (2019). http://doi.org/10.1021/ACS.INORGCHEM.8B03485
Abstract: The chemical accessibility of the Celv oxidation state enables redox chemistry to be performed on the naturally coinagemetal -deficient phases CeM1-xSO (M = Cu, Ag). A metastable black compound with the PbFC1 structure type (space group P4/nmm: a = 3.8396(1) angstrom, c = 6.607(4) angstrom, V = 97.40(6) angstrom(3)) and a composition approaching CeSO is obtained by deintercalation of Ag from CeAg0.8SO. High-resolution transmission electron microscopy reveals the presence of large defect-free regions in CeSO, but stacking faults are also evident which can be incorporated into a quantitative model to account for the severe peak anisotropy evident in all the highresolution X-ray and neutron diffractograms of bulk CeSO samples; these suggest that a few percent of residual Ag remains. A strawcolored compound with the filled PbFCI (i.e., ZrSiCuAs- or HfCuSi2type) structure (space group P4/nmm: a = 3.98171(1) angstrom, c = 8.70913(5) angstrom, V = 138.075(1) angstrom 3) and a composition close to LiCeSO, but with small amounts of residual Ag, is obtained by direct reductive lithiation of CeAga8S0 or by insertion of Li into CeSO using chemical or electrochemical means. Computation of the band structure of pure, stoichiometric CeSO predicts it to be a Ce' compound with the 4f-states lying approximately 1 eV above the sulfide-dominated valence band maximum. Accordingly, the effective magnetic moment per Ce ion measured in the CeSO samples is much reduced from the value found for the Ce3+-containing LiCeSO, and the residual paramagnetism corresponds to the Ce3+ ions remaining due to the presence of residual Ag, which presumably reflects the difficulty of stabilizing Ce' in the presence of sulfide (S2-). Comparison of the behavior of CeCu0.8SO with that of CeCu0.8SO reveals much slower reaction kinetics associated with the Cu,_xS layers, and this enables intermediate CeCui LixSO phases to be isolated.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 4.857
DOI: 10.1021/ACS.INORGCHEM.8B03485
|
“Synthesis and Characterization of Double Solid Solution (Zr,Ti)(2)(Al,Sn)C MAX Phase Ceramics”. Tunca B, Lapauw T, Delville R, Neuville DR, Hennet L, Thiaudiere D, Ouisse T, Hadermann J, Vleugels J, Lambrinou K, Inorganic chemistry 58, 6669 (2019). http://doi.org/10.1021/ACS.INORGCHEM.9B00065
Abstract: Quasi phase-pure (>98 wt %) MAX phase solid solution ceramics with the (ZryTi)(2)(Al-0.5,Sn-0.5)C stoichiometry and variable Zr/Ti ratios were synthesized by both reactive hot pressing and pressureless sintering of ZrH2, TiH2, Al, Sn, and C powder mixtures. The influence of the different processing parameters, such as applied pressure and sintering atmosphere, on phase purity and microstructure of the produced ceramics was investigated. The addition of Sn to the (Zr,Ti)(2)AlC system was the key to achieve phase purity. Its effect on the crystal structure of a 211-type MAX phase was assessed by calculating the distortions of the octahedral M6C and trigonal M(6)A prisms due to steric effects. The M(6)A prismatic distortion values were found to be smaller in Sn-containing double solid solutions than in the (Zr,Ti)(2)AlC MAX phases. The coefficients of thermal expansion along the < a > and < c > directions were measured by means of Rietveld refinement of high-temperature synchrotron X-ray diffraction data of (Zr1-x,Ti-x)(2)(Al-0.5,Sn-0.5)C MAX phase solid solutions with x = 0, 0.3, 0.7, and 1. The thermal expansion coefficient data of the Ti-2(Al-0.5,Sn-0.5)C solid solution were compared with those of the Ti2AlC and Ti2SnC ternary compounds. The thermal expansion anisotropy increased in the (Zr,Ti)(2)(Al-0.5,Sn-0.5)C double solid solution MAX phases as compared to the Zr-2(Al-0.5,Sn-0.5)C and Ti-2(Al-0.5,Sn-0.5)C end-members.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 4.857
Times cited: 3
DOI: 10.1021/ACS.INORGCHEM.9B00065
|
“Computationally Driven Discovery of a Family of Layered LiNiB Polymorphs”. Gvozdetskyi V, Bhaskar G, Batuk M, Zhao X, Wang R, Carnahan SL, Hanrahan MP, Ribeiro RA, Canfield PC, Rossini AJ, Wang C-Z, Ho K-M, Hadermann J, Zaikina JV, Angewandte Chemie: international edition in English 58, 15855 (2019). http://doi.org/10.1002/anie.201907499
Abstract: Two novel lithium nickel boride polymorphs RT-LiNiB and HT-LiNiB with layered crystal structures are reported. This family of compounds was theoretically predicted by using the adaptive genetic algorithm (AGA) and subsequently synthesized via a hydride route with LiH precursor as a lithium source. Being unique among the known ternary transition metal borides, the LiNiB structures feature Li layers alternating with nearly planar [NiB] layers, composed of Ni hexagonal rings centered by B-B pairs. A comprehensive study using a combination of single crystal/synchrotron powder X-ray diffraction data, solid-state 7Li and 11B NMR, scanning transmission electron microscopy, quantum chemistry calculations, and magnetism has shed light on the intrinsic features of these polymorphic compounds. The unique layered structures of LiNiB compounds make them ultimate precursors to further study their exfoliation, paving a way toward two-dimensional transition metal borides, MBenes.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 11.994
DOI: 10.1002/anie.201907499
|
“A titanium(IV)-based metal-organic framework featuring defect-rich Ti-O sheets as an oxidative desulfurization catalyst”. Smolders S, Willhammar T, Krajnc A, Şentosun K, Wharmby MT, Lomachenko KA, Bals S, Mali G, Roeffaers MBJ, De Vos DE, Bueken B, Angewandte Chemie: international edition in English 58, 9160 (2019). http://doi.org/10.1002/ANIE.201904347
Abstract: While titanium-based metal-organic frameworks (MOFs) have been widely studied for their (photo) catalytic potential, only a few Ti-IV MOFs have been reported owing to the high reactivity of the employed titanium precursors. The synthesis of COK-47 is now presented, the first Ti carboxylate MOF based on sheets of (TiO6)-O-IV octahedra, which can be synthesized with a range of different linkers. COK-47 can be synthesized as an inherently defective nanoparticulate material, rendering it a highly efficient catalyst for the oxidation of thiophenes. Its structure was determined by continuous rotation electron diffraction and studied in depth by X-ray total scattering, EXAFS, and solid-state NMR. Furthermore, its photoactivity was investigated by electron paramagnetic resonance and demonstrated by catalytic photodegradation of rhodamine 6G.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 11.994
Times cited: 97
DOI: 10.1002/ANIE.201904347
|
“Exsolution of SrO during the Topochemical Conversion of LaSr3CoRuO8to the Oxyhydride LaSr3CoRuO4H4”. Jin L, Batuk M, Kirschner FKK, Lang F, Blundell SJ, Hadermann J, Hayward MA, Inorganic chemistry 58, 14863 (2019). http://doi.org/10.1021/acs.inorgchem.9b02552
Abstract: Reaction of the n = 1 Ruddlesden-Popper oxide LaSr3CoRuO8 with CaH2 yields the oxyhydride phase LaSr3CoRuO4H4 via topochemical anion-exchange. Close inspection of X-ray and neutron powder diffraction data in combination with HAADF-STEM images reveals that nanoparticles of SrO are exsolved from the system during the reaction, with the change in cation stoichiometry accommodated by the inclusion of n > 1 (Co/Ru)nOn+1H2n ‘perovskite’ layers into the Ruddlesden-Popper stacking sequence. This novel pseudo-topochemical process offers a new route for the formation of n > 1 Ruddlesden-Popper structured materials. Magnetization data are consistent with a LaSr3Co1+Ru2+O4H4 (Co1+, d8, S = 1; Ru2+, d6, S = 0) oxidation/spin state combination. Neutron diffraction and μ+SR data show no evidence for long-range magnetic order down to 2 K, suggesting the diamagnetic Ru2+ centers impede the Co-Co magnetic exchange interactions.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 4.857
Times cited: 1
DOI: 10.1021/acs.inorgchem.9b02552
|
“Rembrandt's An Old Man in Military Costume : combining hyperspectral and MA-XRF imaging to understand how two paintings were painted on a single panel”. MacLennan D, Trentelman K, Szafran Y, Woollett AT, Delaney JK, Janssens K, Dik J, Journal of the American Institute for Conservation 58, 54 (2019). http://doi.org/10.1080/01971360.2018.1540245
Abstract: Over the past several decades the painting An Old Man in Military Costume by Rembrandt Harmensz van Rijn (ca. 1630-31; J. Paul Getty Museum, 78.PB.246) has been the subject of a number of investigations carried out in order to better visualize a second painting beneath the surface figure. The underlying image – the head and shoulders of a man wearing a cloak – is oriented 180 degrees from the upper image and appears to be fairly complete. Scanning macro x-ray fluorescence (XRF) spectroscopy reveals the face is painted with lead white and a mercury-containing pigment (likely vermilion), and the cloak is painted with a copper-containing pigment. Following the revelation and digital color reconstruction of the underlying figure, a number of questions still remained. Here, through the use of infrared reflectance imaging spectroscopy (i.e., hyperspectral imaging) and macro-XRF imaging spectroscopy, together with cross-sections taken from targeted areas, the sequence of painting in both compositions was explored. Of particular interest was the discovery of evidence of multiple attempts to situate the lower figure, and the subsequent application of a blocking-out layer over the lower figure before the artist rotated the panel and executed the upper figure. In addition, examination of the placement of the two images on the panel adds to our understanding of the subtle complexities of Rembrandt's working process. RESUMEAu cours des dernieres decennies, la peinture Le vieil homme en costume militaire de Rembrandt Harmensz van Rijn (ca. 1630-31; J. Paul Getty Museum, 78.PB.246) a fait l'objet de nombreuses investigations menees dans le but de mieux visualiser une seconde peinture dissimulee sous la surface. L'image sous-jacente – la tete et les epaules d'un homme vetu d'une cape – est orientee a 180 degres de de l'image du vieil homme, et elle semble assez complete. La spectroscopie a macro-balayage de fluorescence X (MA-XRF) revele que le visage est peint avec du blanc de plomb et un pigment contenant du mercure (comme le vermillon), et que la cape est peinte avec un pigment a base de cuivre. Plusieurs questions restaient en suspens suite a cette decouverte et a la reconstruction numerique en couleur de l'image sous-jacente. Grace a l'emploi de techniques d'imagerie comme la spectroscopie proche infrarouge (ex., imagerie hyperspectrale) et l'imagerie MA-XRF, combinees a l'analyse de coupes stratigraphiques prelevees a des endroits cibles, on a pu explorer la sequence d'application des couches picturales de chacune des deux compositions. Une decouverte particulierement interessante est la preuve que l'artiste a fait plusieurs tentatives pour positionner la figure sous-jacente puis, a ensuite applique une couche pour la recouvrir completement avant de faire pivoter le panneau et peindre la figure du vieil homme. De plus, l'examen du positionnement des deux images sur le panneau ajoute a notre comprehension de la subtile complexite du processus de creation de Rembrandt. Traduit par Elisabeth Forest. RESUMONas ultimas decadas, a pintura Um Velho em Traje Militar, de Rembrandt Harmensz van Rijn (ca. 1630-31; J. Paul Getty Museum, 78.PB.246), foi objeto de uma serie de investigacoes realizadas para visualizar melhor uma segunda pintura abaixo da figura aparente. A imagem subjacente – a cabeca e os ombros de um homem usando uma capa – e orientada a 180 graus da imagem superior e parece estar bastante completa. O macro mapeamento de imagem por espectroscopia de fluorescencia de raios X (FRX) revela que a face e pintada com branco de chumbo e um pigmento contendo mercurio (provavelmente vermelhAo), e a capa e pintada com um pigmento contendo cobre. Apos a descoberta e reconstrucAo digital da cor da figura subjacente, uma serie de questoes ainda permanecem. EntAo, atraves da utilizacAo do mapeamento por imagem de espectroscopia de refletancia por infravermelhos (i.e. mapeamento hiperespectral) e macro mapeamento por imagem de FRX, juntamente com cortes estratigraficos de amostras retiradas de areas de interesse, a pintura em ambas as composicoes foi explorada. De particular interesse foi a descoberta de evidencias de multiplas tentativas de posicionar a figura subjacente, e a subsequente aplicacAo de uma camada intermediaria de separacAo sobre a figura inferior antes do artista girar o painel e executar a figura superior. Alem disso, o exame da colocacAo das duas imagens no painel aumenta nossa compreensAo das sutis complexidades do processo de trabalho de Rembrandt. Traduzido por Marcia Rozzi e Beatriz Haspo. RESUMENA lo largo de las ultimas decadas, la pintura Un anciano con traje militar de Rembrandt Harmensz van Rijn (ca. 1630-31; J. Paul Getty Museum, 78.PB.246) ha sido objeto de varias investigaciones realizadas con el fin de visualizar mejor una segunda pintura debajo de la figura de la superficie. La imagen subyacente, la cabeza y los hombros de un hombre que lleva una capa, esta orientada a 180 grados de la imagen superior y parece estar bastante completa. La espectroscopia de fluorescencia de rayos X (XRF) de barrido revela que la cara esta pintada con blanco de plomo y un pigmento que contiene mercurio (probablemente bermellon), y la capa esta pintada con un pigmento que contiene cobre. Tras la revelacion y la reconstruccion digital del color de la figura subyacente, aun quedaban algunas preguntas. Aqui, por medio del uso de la espectroscopia de imagenes de reflectancia infrarroja (es decir, imagenes hiperespectrales) e imagenes macro-XRF, junto con las secciones transversales tomadas de areas especificas, se exploro la secuencia de pintura en ambas composiciones. De particular interes fue el descubrimiento de evidencia de multiples intentos de situar la figura inferior, y la aplicacion posterior de una capa de bloqueo sobre la figura inferior antes de que el artista rotara el panel y ejecutara la figura superior. Ademas, el examen de la colocacion de las dos imagenes en el panel contribuye a nuestra comprension de las sutiles complejidades del proceso de trabajo de Rembrandt. Traduccion: Amparo Rueda.
Keywords: A1 Journal article; Art; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation)
Times cited: 2
DOI: 10.1080/01971360.2018.1540245
|
“Phase transformation behavior of a two-dimensional zeolite”. Bae J, Cichocka MO, Zhang Y, Bacsik Z, Bals S, Zou X, Willhammar T, Hong SB, Angewandte Chemie: international edition in English 58, 10230 (2019). http://doi.org/10.1002/ANIE.201904825
Abstract: Understanding the molecular-level mechanisms of phase transformation in solids is of fundamental interest for functional materials such as zeolites. Two-dimensional (2D) zeolites, when used as shape-selective catalysts, can offer improved access to the catalytically active sites and a shortened diffusion length in comparison with their 3D analogues. However, few materials are known to maintain both their intralayer microporosity and structure during calcination for organic structure-directing agent (SDA) removal. Herein we report that PST-9, a new 2D zeolite which has been synthesized via the multiple inorganic cation approach and fulfills the requirements for true layered zeolites, can be transformed into the small-pore zeolite EU-12 under its crystallization conditions through the single-layer folding process, but not through the traditional dissolution/recrystallization route. We also show that zeolite crystal growth pathway can differ according to the type of organic SDAs employed.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Times cited: 2
DOI: 10.1002/ANIE.201904825
|