|
“Catalyst traces after chemical purification in CVD grown carbon nanotubes”. Biró, LP, Khanh NQ, Horváth ZE, Vértesy Z, Kocsonya A, Konya Z, Osváth Z, Koós A, Guylai J, Zhang XB, Van Tendeloo G, Fonseca A, Nagy JB, , 183 (2001)
Keywords: P3 Proceeding; Electron microscopy for materials research (EMAT)
|
|
|
“Large scale synthesis of carbon nanotubes and their composite materials”. Nagy JB, Fonseca A, Pierard N, Willems I, Bister G, Pirlot C, Demortier A, Delhalle J, Mekhalif Z, Niesz K, Bossuot C, Pirard J-P, Biró, LP, Konya Z, Colomer J-F, Van Tendeloo G, Kiricsi I, (2001)
Keywords: P3 Proceeding; Electron microscopy for materials research (EMAT)
|
|
|
“Synthesis of single wall carbon nanotubes by catalytic decomposition of hydrocarbons”. Colomer J-F, Bister G, Willems I, Konya Z, Fonseca A, Van Tendeloo G, Nagy JB, Chemical communications , 1343 (1999). http://doi.org/10.1039/a903142a
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 6.319
Times cited: 110
DOI: 10.1039/a903142a
|
|
|
“Production of differently shaped multi-wall carbon nanotubes using various cobalt supported catalysts”. Piedigrosso P, Konya Z, Colomer J-F, Fonseca A, Van Tendeloo G, Nagy JB, Physical chemistry, chemical physics 2, 163 (2000). http://doi.org/10.1039/a905622j
Abstract: Catalytic synthesis and transmission electron microscopy (TEM) of multi-wall carbon nanotubes are presented. Silica, zeolite and alumina supported cobalt catalysts were prepared by different methods (impregnation and ion-adsorption precipitation) and were used to produce nanotubes. The synthesis was carried out in a fixed bed flow reactor and the process was optimized in order to produce carbon nanotubes on a gram scale. The influence of various parameters such as the method of catalyst preparation, the nature of the support, cobalt concentration and reaction conditions on the formation of nanotubes was investigated. The carbon deposits were measured and the quality of nanotubes was determined by low and high resolution TEM. Multi-wall straight and coiled nanotubes were found to be fairly regular with an average inner (outer) diameter of 4-7 nm (8-23 nm) and with lengths up to 0.1 mm.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 4.123
Times cited: 53
DOI: 10.1039/a905622j
|
|
|
“Catalyst traces and other impurities in chemically purified carbon nanotubes grown by CVD”. Biró, LP, Khanh NQ, Vértesy Z, Horváth ZE, Osváth Z, Koós A, Gyulai J, Kocsonya A, Kónya Z, Zhang XB, Van Tendeloo G, Fonseca A, Nagy JB;, Materials science and engineering: part C: biomimetic materials
T2 –, EMRS Spring Meeting, JUN 05-08, 2001, STRASBOURG, FRANCE 19, 9 (2002). http://doi.org/10.1016/S0928-4931(01)00407-6
Abstract: Multiwall carbon nanotubes grown by the catalytic decomposition of acetylene over supported Co catalyst were subjected to wet and dry oxidation in order to remove the unwanted products and the catalyst traces. The effects of the purification treatment on the Co content was monitored by physical methods: Rutherford Backscattering Spectrometry (RBS). Particle Induced X-Ray Emission (PIXE) and X-Ray Fluorescence (XRF). The purified products were investigated by microscopic methods: TEM. Scanning Electron Microscopy (SEM), Energy Dispersive Spectroscopy (EDS) and STM. The KMnO4/H2SO4 aqueous oxidation procedure was found to be effective in reducing the Co content while damaging only moderately the outer wall of the nanotubes. Treatment in HNO3/H2SO4 yields a bucky-paper like product and produces the increase of the Si and S content of the sample. (C) 2002 Elsevier Science B.V. All rights reserved.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 4.164
Times cited: 36
DOI: 10.1016/S0928-4931(01)00407-6
|
|
|
“The texture of catalytically grown coil-shaped carbon nanotubes”. Zhang XB, Zhang XF, Bernaerts D, Van Tendeloo G, Amelinckx S, van Landuyt J, Ivanov V, Nagy JB, Lambin P, Lucas AA, Europhysics letters 27, 141 (1994). http://doi.org/10.1209/0295-5075/27/2/011
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 2.095
Times cited: 168
DOI: 10.1209/0295-5075/27/2/011
|
|
|
“Ball milling effect on the structure of single-wall carbon nanotubes”. Pierard N, Fonseca A, Colomer J-F, Bossuot C, Benoit J-M, Van Tendeloo G, Pirard J-P, Nagy JB, Carbon 42, 1691 (2004). http://doi.org/10.1016/j.carbon.2004.02.031
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 6.337
Times cited: 133
DOI: 10.1016/j.carbon.2004.02.031
|
|
|
“Multiwalled carbon nanotubes functionalized with 7-octenyltrichlorosilane and n-octyltrichlorosilane: dispersion in Sylgard®184 silicone and Youngs modulus”. Vast L, Carpentier L, Lallemand F, Colomer J-F, Van Tendeloo G, Fonseca A, Nagy JB, Mekhalif Z, Delhalle J, Journal of materials science 44, 3476 (2009). http://doi.org/10.1007/s10853-009-3464-1
Abstract: Sylgard®184/multiwalled carbon nanotube (MWNT) composites have been prepared by in situ polymerization using purified and functionalized multiwalled carbon nanotubes (f-MWNTs) as fillers. Surface modification of the MWNTs has been carried out by silanization with 7-octenyltrichlorosilane (7OTCS) and n-octyltrichlorosilane (nOTCS). The modification and dispersion of the carbon nanotubes in composites were characterized by X-ray photoelectron spectroscopy (XPS), transmission electron spectroscopy (TEM), and high-resolution transmission electron spectroscopy (HRTEM). Youngs modulus results were derived from indentation testing. It is shown that the terminal-vinyl group of 7OTCS molecules plays an essential role for both the dispersion of the f-MWNTs in the composite and its mechanical properties. At loading as low as 0.2 wt%, the Youngs modulus is shown to increase up to 50%. This is interpreted as resulting from a combination of the good compatibility in the forming silicone matrix of the MWNTs coated with a siloxane network, on the one hand, and the covalent links created between the terminal-vinyl groups and the host matrix in formation, on the other hand.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 2.599
Times cited: 16
DOI: 10.1007/s10853-009-3464-1
|
|
|
“Electron microscopy study of coiled carbon tubules”. Bernaerts D, Zhang XB, Zhang XF, Amelinckx S, Van Tendeloo G, van Landuyt J, Ivanov V, Nagy JB, Philosophical magazine: A: physics of condensed matter: defects and mechanical properties 71, 605 (1995). http://doi.org/10.1080/01418619508244470
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Times cited: 72
DOI: 10.1080/01418619508244470
|
|
|
“Optimization of the amount of catalyst and reaction time in single wall nanotube production”. Horvath ZE, Biro LP, Van Tendeloo G, Tondeur C, Bister G, Pierard N, Fonseca A, Nagy JB, Diffusion and defect data : solid state data : part B : solid state phenomena 94, 271 (2003)
Abstract: The influence of the amount of catalyst and the reaction time on the quantity and quality of catalytically grown single wall carbon nanotubes (SWNT) was investigated. The aim was to optimize some of the SWNT growth parameters using TEM and HRTEM. The thickness of catalyst layer influences the synthesis of the nanotube because the gas composition can differ between top and bottom. Microscopic investigation of the grown SWNT samples showed that the thicker the catalyst layer the lower relative nanotube content, so the deeper parts of the catalyst layer are less effective: The optimum time for the reaction was found to be 10 minutes. This may be understood assuming that nanotube growth needs an initial incubation time while the activity of the catalyst decreases steadily until the nariotube growth stops.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
|
|
|
“Purification of catalytically produced multi-wall nanotubes”. Colomer J-F, Piedigrosso P, Willems I, Journet C, Bernier P, Van Tendeloo G, Fonseca A, Nagy JB, Journal of the Chemical Society : Faraday transactions: physical chemistry and chemical physics 94, 3753 (1998). http://doi.org/10.1039/a806804f
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Times cited: 92
DOI: 10.1039/a806804f
|
|
|
“TEM and laser-polarized 129Xe NMR characterization of oxidatively purified carbon nanotubes”. Kneller JM, Soto RJ, Surber SE, Colomer JF, Fonseca A, Nagy JB, Van Tendeloo G, Pietrass T, Journal of the American Chemical Society 122, 10591 (2000). http://doi.org/10.1021/ja994441y
Abstract: Multiwall carbon nanotubes are produced by decomposition of acetylene at 600 degreesC on metal catalysts supported on NaY zeolite. The support and the metal are eliminated by dissolving them in aqueous hydrofluoric acid (HF). Two methods were used to eliminate the pyrolitic carbon: oxidation in air at 500 degreesC and oxidation by potassium permanganate in acidic solution at 70 degreesC. The progress and efficacy of the purification methods are verified by TEM. The properties of the purified multiwalled carbon nanotubes are probed using C-13 and Xe-129 NMR spectroscopy under continuous-flow optical-pumping conditions. Xenon is shown to penetrate the interior of the nanotubes. A distribution of inner tube diameters gives rise to chemical shift dispersion. When the temperature is lowered, an increasing fraction of xenon resides inside the nanotubes and is not capable of exchanging with xenon in the interparticle space. In the case of the permanganate-oxidized sample, rapid xenon relaxation is attributed to interaction with residual MnO2 nanoparticles in the interior of the tubes.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 13.858
Times cited: 53
DOI: 10.1021/ja994441y
|
|
|
“The study of carbon nanotubes produced by catalytic method”. Ivanov V, Nagy JB, Lambin P, Lucas A, Zhang XB, Zhang XF, Bernaerts D, Van Tendeloo G, Amelinckx S, van Landuyt J, Chemical physics letters 223, 329 (1994)
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 1.897
Times cited: 405
|
|
|
“The study of carbon nanotubules produced by catalytic method”. Ivanov V, Nagy JB, Lambin P, Lucas A, Zhang XB, Zhang XF, Bernaerts D, Van Tendeloo G, Amelinckx S, van Landuyt J, Chemical physics letters 223, 329 (1994). http://doi.org/10.1016/0009-2614(94)00467-6
Abstract: Catalytic methods for the production of carbon nanotubules have been developed based on the decomposition of acetylene on well-dispersed metal particles strongly adsorbed on a support. Cobalt on silica was found to be the best catalyst-support combination for the production of graphitic tubules. The method for the catalyst preparation and the reaction conditions were optimized. Straight and coiled carbon tubules were obtained with inner and outer diameter of 3-7 and 15-20 nm, respectively, and up to 30 mum in length. These nanotubules were not coated by amorphous carbon. Traces of amorphous carbon could be removed by hydrogen. High resolution electron microscopy images and electron diffraction patterns of the straight nanotubules were similar to those obtained by the arc-discharge method. Coiled nanotubules were revealed by TEM to be regular polygonized helices where the bends are caused by pairs of pentagon-heptagon carbon rings among the hexagonal network.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 1.897
Times cited: 405
DOI: 10.1016/0009-2614(94)00467-6
|
|
|
“Control of the outer diameter of thin carbon nanotubes synthesized by catalytic decomposition of hydrocarbons”. Willems I, Konya Z, Colomer JF, Van Tendeloo G, Nagaraju N, Fonseca A, Nagy JB, Chemical physics letters 317, 71 (2000). http://doi.org/10.1016/S0009-2614(99)01300-7
Abstract: Multi-wall carbon nanotubes have been produced by the catalytic decomposition of acetylene. Go-Mo, Co-V and Co-Fe mixtures supported either on zeolite or corundum alumina were used as catalysts. When Fe or V is added to Co, the carbon deposit increases. The nanotubes were characterized by both low and high resolution TEM. From histograms representing the outer diameter distributions, it is clear that the outer diameter of the nanotubes can be controlled by choosing the appropriate catalyst. (C) 2000 Elsevier Science B.V. All rights reserved.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 1.815
Times cited: 130
DOI: 10.1016/S0009-2614(99)01300-7
|
|
|
“Large-scale synthesis of single-wall carbon nanotubes by catalytic chemical vapor deposition (CCVD) method”. Colomer JF, Stephan C, Lefrant S, Van Tendeloo G, Willems I, Konya Z, Fonseca A, Laurent C, Nagy JB, Chemical physics letters 317, 83 (2000). http://doi.org/10.1016/S0009-2614(99)01338-X
Abstract: The large-scale production of single-wall carbon nanotubes (SWNTs) is reported. Large quantities of SWNTs can be synthesised by catalytic decomposition of methane over well-dispersed metal particles supported on MgO at 1000 degrees C. The thus produced SWNTs can be separated easily from the support by a simple acidic treatment to obtain a product with high yields (70-80%) of SWNTs. Because the typical synthesis time is 10 min, 1 g of SWNTs can be synthesised per day by this method. The SWNTs are characterized by high-resolution transmission electron microscopy and by Raman spectroscopy, showing the quality and the quantity of products. (C) 2000 Elsevier Science B.V. All rights reserved.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 1.815
Times cited: 344
DOI: 10.1016/S0009-2614(99)01338-X
|
|
|
“Production of short carbon nanotubes with open tips by ball milling”. Pierard N, Fonseca A, Konya Z, Willems I, Van Tendeloo G, Nagy JB, Chemical physics letters 335, 1 (2001). http://doi.org/10.1016/S0009-2614(01)00004-5
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 1.815
Times cited: 203
DOI: 10.1016/S0009-2614(01)00004-5
|
|
|
“Characterization of single-wall carbon nanotubes produced by CCVD method”. Colomer J-F, Benoit J-M, Stephan C, Lefrant S, Van Tendeloo G, Nagy JB, Chemical physics letters 345, 11 (2001). http://doi.org/10.1016/S0009-2614(01)00841-7
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 1.815
Times cited: 45
DOI: 10.1016/S0009-2614(01)00841-7
|
|