|
“Ureolytic activity and its regulation in vibrio campbellii and vibrio harveyi in relation to nitrogen recovery from human urine”. Defoirdt T, Vlaeminck SE, Sun X, Boon N, Clauwaert P, Environmental science and technology 51, 13335 (2017). http://doi.org/10.1021/ACS.EST.7B03829
Abstract: Human urine contains a high concentration of nitrogen and is therefore an interesting source for nutrient recovery. Ureolysis is a key requirement in many processes aiming at nitrogen recovery from urine. Although ureolytic activity is widespread in terrestrial and aquatic environments, very little is known about the urease activity and regulation in specific bacteria other than human pathogens. Given the relatively high salt concentration of urine, marine bacteria would be particularly well suited for biotechnological applications involving nitrogen recovery from urine, and therefore, in this study, we investigated ureolytic activity and its regulation in marine vibrios. Thirteen out of 14 strains showed ureolytic activity. The urease activity was induced by urea, since complete and very rapid hydrolysis, up to 4 g L-1 of urea, was observed in synthetic human urine when the bacteria were pretreated with 10 g L-1 urea, whereas slow hydrolysis occurred when they were pretreated with 1 g L-1 urea (14-35% hydrolysis after 2 days). There was no correlation between biofilm formation and "motility on one hand, and ureolysis on the other hand, and biofilm and motility inhibitors did not affect ureolysis. Together, our data demonstrate for the first time the potential of marine vibrios as fast urea hydrolyzers for biotechnological applications aiming at nutrient recovery from human urine.
Keywords: A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1021/ACS.EST.7B03829
|
|
“Urban soil exploration through multi-receiver electromagnetic induction and stepped-frequency ground penetrating radar”. Van de Vijver E, Van Meirvenne M, Vandenhaute L, Delefortrie S, De Smedt P, Saey T, Seuntjens P, Environmental science : processes &, impacts 17, 1271 (2015). http://doi.org/10.1039/C5EM00023H
Abstract: In environmental assessments, the characterization of urban soils relies heavily on invasive investigation, which is often insufficient to capture their full spatial heterogeneity. Non-invasive geophysical techniques enable rapid collection of high-resolution data and provide a cost-effective alternative to investigate soil in a spatially comprehensive way. This paper presents the results of combining multi-receiver electromagnetic induction and stepped-frequency ground penetrating radar to characterize a former garage site contaminated with petroleum hydrocarbons. The sensor combination showed the ability to identify and accurately locate building remains and a high-density soil layer, thus demonstrating the high potential to investigate anthropogenic disturbances of physical nature. In addition, a correspondence was found between an area of lower electrical conductivity and elevated concentrations of petroleum hydrocarbons, suggesting the potential to detect specific chemical disturbances. We conclude that the sensor combination provides valuable information for preliminary assessment of urban soils.
Keywords: A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1039/C5EM00023H
|
|
“Unveiling the composition of sulphur sensitization specks by their interactions with TAI”. Charlier E, van Doorselaer M, Gijbels R, de Keyzer R, Geuens I, Journal Of Imaging Science And Technology 44, 235 (2000)
Abstract: A two-step process for the formation of sensitivity centers different from earlier described two-step processes was found for sulfur sensitized emulsions. After deposition of sulfur in the first step, it was found that the second step does not consist of rearrangement of sulfur over the surface, but of the supply of silver interstitial ions towards the deposited sulfur clusters. The two processes could be separated by adsorbing and desorbing TAI (4-hydroxy-1, 3,3a, 7-tetraazaindene) at/from the silver halide surface. When 1.5 mmol TAI/mol Ag is added before the sulfur reaction, the silver interstitials are immobilized but sulfur still can be deposited at the same level. By lowering the pH to 2.50 after this sulfur reaction, TAI is desorbed from the surface and the released interstitials then cause a restoration of the properties of a sulfur system without TAI. These effects could be demonstrated via diffuse reflectance spectroscopy (DRS), sensitometry and dielectric loss measurements. We could also confirm the isolation of silver sulfide clusters by TAI from other chemicals in the solution, by adsorption of TAI on the clusters.
Keywords: A1 Journal article; Engineering sciences. Technology; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Impact Factor: 0.348
Times cited: 16
|
|
“Unveiling the binding mode of perfluorooctanoic acid to human serum albumin”. Maso L, Trande M, Liberi S, Moro G, Daems E, Linciano S, Sobott F, Covaceuszach S, Cassetta A, Fasolato S, Moretto LM, De Wael K, Cendron L, Angelini A, Protein Science 30, 830 (2021). http://doi.org/10.1002/PRO.4036
Abstract: Perfluorooctanoic acid (PFOA) is a toxic compound that is absorbed and distributed throughout the body by noncovalent binding to serum proteins such as human serum albumin (hSA). Though the interaction between PFOA and hSA has been already assessed using various analytical techniques, a high resolution and detailed analysis of the binding mode is still lacking. We report here the crystal structure of hSA in complex with PFOA and a medium-chain saturated fatty acid (FA). A total of eight distinct binding sites, four occupied by PFOAs and four by FAs, have been identified. In solution binding studies confirmed the 4:1 PFOA-hSA stoichiometry and revealed the presence of one high and three low affinity binding sites. Competition experiments with known hSA-binding drugs allowed locating the high affinity binding site in sub-domain IIIA. The elucidation of the molecular basis of the interaction between PFOA and hSA might provide not only a better assessment of the absorption and elimination mechanisms of these compounds in vivo but also have implications for the development of novel molecular receptors for diagnostic and biotechnological applications.
Keywords: A1 Journal article; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation)
Impact Factor: 2.523
DOI: 10.1002/PRO.4036
|
|
“Unusual commensurability effects in quasiperiodic pinning arrays induced by local inhomogeneities of the pinning site density”. Bothner D, Seidl R, Misko VR, Kleiner R, Koelle D, Kemmler M, Superconductor science and technology 27, 065002 (2014). http://doi.org/10.1088/0953-2048/27/6/065002
Abstract: We experimentally investigate the magnetic field dependence of the critical current I-c(B) of superconducting niobium thin films patterned with periodic and quasiperiodic antidot arrays on the submicron scale. For this purpose we monitor current-voltage characteristics at different values of B and temperature T. We investigate samples with antidots positioned at the vertices of two different tilings with quasiperiodic symmetry, namely the Shield Tiling and the Tuebingen Triangle Tiling. For reference we investigate a sample with a triangular antidot lattice. We find modulations of the critical current for both quasiperiodic tilings, which have partly been predicted by numerical simulations but not observed in experiments yet. The particularity of these commensurability effects is that they correspond to magnetic field values slightly above an integer multiple of the matching field. The observed matching effects can be explained by the caging of interstitial vortices in quasiperiodically distributed cages and the formation of symmetry-induced giant vortices.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 2.878
Times cited: 7
DOI: 10.1088/0953-2048/27/6/065002
|
|
“Unravelling the solvent flux behaviour of ceramic nanofiltration and ultrafiltration membranes”. Buekenhoudt A, Bisignano F, De Luca G, Vandezande P, Wouters M, Verhulst K, Journal of membrane science 439, 36 (2013). http://doi.org/10.1016/j.memsci.2013.03.032
Abstract: In order to increase the understanding of the underlying processes in organic solvent nanofiltration (OSN), a study has been undertaken aimed at clarifying the solvent flux behaviour of ceramic nanofiltration and ultrafiltration membranes. Ceramic membranes were chosen for their non-swelling character. Pure water and a variation of 11 different organic solvents were measured on a series of different ceramic membranes with pore-size diameters ranging from 0.9 nm up to 100 nm. To avoid any historical effects, each flux measurement was carried out on a new membrane. The flux results were analysed in a phenomenological way, and a common very simple linear relationship was observed between the product of flux and viscosity of the solvent, and the total Hansen solubility parameter of the solvent. The linear relationship was found for all membranes, independent of the membrane pore size and the membrane material. The slope of the linear relationship was found to depend exponentially on the pore-size diameter and on the polarity of the membrane surface. This result emphasizes the importance of viscosity in the solvent transport, but also of the polarity difference between membrane surface and solvent. The very simple flux model deduced, allows a straightforward prediction of the flux of any solvent or solvent mixture, once the water flux of the membrane is known. At the high pore-size end, the phenomenological model naturally transforms into the viscous-flow or pore-flow behaviour as required. A tentative physical explanation of the model takes into account the presence and extension of a water layer adsorbed to the total pore surface of these membranes. This work also shows that the water flux of a hydrophilic membrane gives a good indication of its molecular weight cut-off (MWCO), and therefore of its separation performance in water. (C)0 2013 Elsevier B.V. All rights reserved.
Keywords: A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT); Applied Electrochemistry & Catalysis (ELCAT)
Impact Factor: 6.035
Times cited: 55
DOI: 10.1016/j.memsci.2013.03.032
|
|
“Unprecedented and highly stable lithium storage capacity of (001) faceted nanosheet-constructed hierarchically porous TiO₂/rGO hybrid architecture for high-performance Li-ion batteries”. Yu W-B, Hu Z-Y, Jin J, Yi M, Yan M, Li Y, Wang H-E, Gao H-X, Mai L-Q, Hasan T, Xu B-X, Peng D-L, Van Tendeloo G, Su B-L, National Science Review 7, 1046 (2020). http://doi.org/10.1093/NSR/NWAA028
Abstract: Active crystal facets can generate special properties for various applications. Herein, we report a (001) faceted nanosheet-constructed hierarchically porous TiO2/rGO hybrid architecture with unprecedented and highly stable lithium storage performance. Density functional theory calculations show that the (001) faceted TiO2 nanosheets enable enhanced reaction kinetics by reinforcing their contact with the electrolyte and shortening the path length of Li+ diffusion and insertion-extraction. The reduced graphene oxide (rGO) nanosheets in this TiO2/rGO hybrid largely improve charge transport, while the porous hierarchy at different length scales favors continuous electrolyte permeation and accommodates volume change. This hierarchically porous TiO2/rGO hybrid anode material demonstrates an excellent reversible capacity of 250 mAh g(-1) at 1 C (1 C = 335 mA g(-1)) at a voltage window of 1.0-3.0 V. Even after 1000 cycles at 5 C and 500 cycles at 10 C, the anode retains exceptional and stable capacities of 176 and 160 mAh g(-1), respectively. Moreover, the formed Li2Ti2O4 nanodots facilitate reversed Li+ insertion-extraction during the cycling process. The above results indicate the best performance of TiO2-based materials as anodes for lithium-ion batteries reported in the literature.
Keywords: A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
Impact Factor: 20.6
Times cited: 3
DOI: 10.1093/NSR/NWAA028
|
|
“Unique nanostructural features in Fe, Mn-doped YBCO thin films”. Meledin A, Turner S, Cayado P, Mundet B, Solano E, Ricart S, Ros J, Puig T, Obradors X, Van Tendeloo G, Superconductor science and technology 29, 125009 (2016). http://doi.org/10.1088/0953-2048/29/12/125009
Abstract: An attempt to grow a thin epitaxial composite film of YBa2Cu3O7−δ (YBCO) with spinel MnFe2O4 (MFO) nanoparticles on a LAO substrate using the CSD approach resulted in a decomposition of the spinel and various doping modes of YBCO with the Fe and Mn cations. These nanostructural effects lead to a lowering of T c and a slight J c increase in field. Using a combination of advanced transmission electron microscopy (TEM) techniques such as atomic resolution high-angle annular dark field scanning TEM, energy dispersive x-ray spectroscopy and electron energy-loss spectroscopy we have been able to decipher and characterize the effects of the Fe and Mn doping on the film architecture. The YBaCuFeO5 anion-deficient double perovskite phase was detected in the form of 3D inclusions as well as epitaxially grown lamellas within the YBCO matrix. These nano-inclusions play a positive role as pinning centers responsible for the J c/J sf (H) dependency smoothening at high magnetic fields in the YBCO-MFO films with respect to the pristine YBCO films.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 2.878
Times cited: 6
DOI: 10.1088/0953-2048/29/12/125009
|
|
“Understanding and optimizing Evolon®, CR for varnish removal from oil paintings”. Baij L, Liu C, Buijs J, Alvarez Martin A, Westert D, Raven L, Geels N, Noble P, Sprakel J, Keune K, Heritage science 9, 155 (2021). http://doi.org/10.1186/S40494-021-00627-9
Keywords: A1 Journal article; Engineering sciences. Technology; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation); Antwerp X-ray Imaging and Spectroscopy (AXIS)
DOI: 10.1186/S40494-021-00627-9
|
|
“Unconventional microanalysis for low-Z, volatile and organic aerosol compounds”. Worobiec A, de Hoog J, Osán J, Szalóki I, Joos P, Van Grieken R, Journal of aerosol science 31, 384 (2000)
Keywords: A1 Journal article; Laboratory Experimental Medicine and Pediatrics (LEMP); AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation)
|
|
“Ultralong Cu(OH)(2) and CuO nanowire bundles: PEG200-directed crystal growth for enhanced photocatalytic performance”. Li Y, Yang X-Y, Rooke J, Van Tendeloo G, Su B-L, Journal of colloid and interface science 348, 303 (2010). http://doi.org/10.1016/j.jcis.2010.04.052
Abstract: Ultralong Cu(OH)(2) and CuO nanowire bundles with lengths ranging from tens to hundreds of micrometers have been selectively synthesized on a large scale by a facile solution-phase method, using PEG200 as growth-directing agent. The growth mechanisms were investigated by monitoring the nanowire evolution process. The results showed that under the action of PEG200 molecules, the Cu(OH)(2) and CuO nanowires were first formed through oriented attachment of colloidal particles, then through side self-assembly leading to nanowire bundles, and finally to CuO nanoleaves. PEG200 plays a critical role in the synthesis of nanowires as it not only prevents the random aggregation of colloidal particles toward CuO nanoleaves but also helps to orientate nanowire growth by the coalescence and alignment in one direction of the colloidal particles. The concentration of OH(-) in the reaction system is also important for nanowire growth. In the absence of PEG200, nanoleaves are formed by an Ostwald ripening process. The band-gap value estimated from a UV-Vis absorption spectrum of CuO nanowire bundles is 2.32 eV. The photodegradation of a model pollutant, rhodamine B, by CuO nanowires and nanoleaves was compared with commercial nanopowders, showing that the as-synthesized ultralong CuO polycrystalline nanowire bundles have an enhanced photocatalytic activity with 87% decomposition of rhodamine B after an 8-h reaction, which was much higher than that of single-crystal nanoleaves (61%) and commercial nanopowders (32%). The origin of the high photocatalytic activity of these new polycrystalline CuO nanowire bundles has been discussed. This present work reveals that the (0 0 2) crystallographic surface is more favorable for photocatalytic decomposition of organic compounds and that these ultralong CuO nanowire bundles are potential candidates for photocatalysts in wastewater treatment. (C) 2010 Elsevier Inc. All rights reserved.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 4.233
Times cited: 70
DOI: 10.1016/j.jcis.2010.04.052
|
|
“Two-dimensional tunneling through magnetic barriers”. Matulis A, Peeters FM, Vasilopoulos P, Surface science : a journal devoted to the physics and chemistry of interfaces 305, 434 (1994). http://doi.org/10.1016/0039-6028(94)90931-8
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 1.925
Times cited: 2
DOI: 10.1016/0039-6028(94)90931-8
|
|
“Two new members of the covalent organic frameworks family : crystalline 2D-oxocarbon and 3D-borocarbon structures”. Hassani N, Movafegh-Ghadirli A, Mahdavifar Z, Peeters FM, Neek-Amal M, Computational materials science 241, 1 (2024). http://doi.org/10.1016/J.COMMATSCI.2024.113022
Abstract: Oxocarbons, known for over two centuries, have recently revealed a long-awaited facet: two-dimensional crystalline structures. Employing an intelligent global optimization algorithm (IGOA) alongside densityfunctional calculations, we unearthed a quasi -flat oxocarbon (C 6 0 6 ), featuring an oxygen -decorated hole, and a novel 3D-borocarbon. Comparative analyses with recently synthesized isostructures, such as 2D -porous carbon nitride (C 6 N 6 ) and 2D -porous boroxine (B 6 0 6 ), highlight the unique attributes of these compounds. All structures share a common stoichiometry of X 6 Y 6 (which we call COF-66), where X = B, C, and Y = B, N, O (with X not equal Y), exhibiting a 2D -crystalline structure, except for borocarbon C 6 B 6 , which forms a 3D crystal. In our comprehensive study, we conducted a detailed exploration of the electronic structure of X 6 Y 6 compounds, scrutinizing their thermodynamic properties and systematically evaluating phonon stability criteria. With expansive surface areas, diverse pore sizes, biocompatibility, pi-conjugation, and distinctive photoelectric properties, these structures, belonging to the covalent organic framework (COF) family, present enticing prospects for fundamental research and hold potential for biosensing applications.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 3.3
DOI: 10.1016/J.COMMATSCI.2024.113022
|
|
“Tuning quantum nonlocal effects in graphene plasmonics”. Lundeberg MB, Gao Y, Asgari R, Tan C, Van Duppen B, Autore M, Alonso-Gonzalez P, Woessner A, Watanabe K, Taniguchi T, Hillenbrand R, Hone J, Polini M, Koppens FHL, Science 357, 187 (2017). http://doi.org/10.1126/SCIENCE.AAN2735
Abstract: The response of electron systems to electrodynamic fields that change rapidly in space is endowed by unique features, including an exquisite spatial nonlocality. This can reveal much about the materials' electronic structure that is invisible in standard probes that use gradually varying fields. Here, we use graphene plasmons, propagating at extremely slow velocities close to the electron Fermi velocity, to probe the nonlocal response of the graphene electron liquid. The near-field imaging experiments reveal a parameter-free match with the full quantum description of the massless Dirac electron gas, which involves three types of nonlocal quantum effects: single-particle velocity matching, interaction-enhanced Fermi velocity, and interaction-reduced compressibility. Our experimental approach can determine the full spatiotemporal response of an electron system.
Keywords: A1 Journal article; Engineering sciences. Technology; Condensed Matter Theory (CMT)
Impact Factor: 37.205
Times cited: 87
DOI: 10.1126/SCIENCE.AAN2735
|
|
“Tunable porous nanoallotropes prepared by post-assembly etching of binary nanoparticle superlattices”. Udayabhaskararao T, Altantzis T, Houben L, Coronado-Puchau M, Langer J, Popovitz-Biro R, Liz-Marzán LM, Vuković, L, Král P, Bals S, Klajn R, Science 358, 514 (2017). http://doi.org/10.1126/science.aan6046
Abstract: Self-assembly of inorganic nanoparticles has been used to prepare hundreds of different colloidal crystals, but almost invariably with the restriction that the particles must be densely packed. Here,we show that non–close-packed nanoparticle arrays can be fabricated through the selective removal of one of two components comprising binary nanoparticle superlattices. First, a variety of binary nanoparticle superlattices were prepared at the liquid-air interface, including several arrangements that were previously unknown. Molecular dynamics simulations revealed the particular role of the liquid in templating the formation of superlattices not achievable through self-assembly in bulk solution. Second, upon stabilization, all of these binary superlattices could be transformed into distinct “nanoallotropes”—nanoporous materials having the same chemical composition but differing in their nanoscale architectures.
Keywords: A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
Impact Factor: 37.205
Times cited: 113
DOI: 10.1126/science.aan6046
|
|
“Tunable electronic and magnetic properties of MoSi₂N₄, monolayer via vacancy defects, atomic adsorption and atomic doping”. Bafekry A, Faraji M, Fadlallah MM, Khatibani AB, Ziabari A abdolahzadeh, Ghergherehchi M, Nedaei S, Shayesteh SF, Gogova D, Applied Surface Science 559, 149862 (2021). http://doi.org/10.1016/J.APSUSC.2021.149862
Abstract: The two dimensional MoSi2N4 (MSN) monolayer exhibiting rich physical and chemical properties was synthesized for the first time last year. We have used the spin-polarized density functional theory to study the effect of different types of point defects on the structural, electronic, and magnetic properties of the MSN monolayer. Adsorbed, substitutionally doped (at different lattice sites), and some kind of vacancies have been considered as point defects. The computational results show all defects studied decrease the MSN monolayer band gap. We found out the H-, O-, and P-doped MSN are n-type conductors. The arsenic-doped MSN, and MSN with vacancy defects have a magnetic moment. The MSN with a Si vacancy defect is a half-metallic which is favorable for spintronic applications, while the MSN with a single N vacancy or double vacancy (N + S) defects are metallic, i. e., beneficial as spin filters and chemical sensors.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 3.387
DOI: 10.1016/J.APSUSC.2021.149862
|
|
“Tunable electronic and magnetic properties of graphene/carbon-nitride van der Waals heterostructures”. Bafekry A, Akgenc B, Shayesteh SF, Mortazavi B, Applied Surface Science 505, 144450 (2020). http://doi.org/10.1016/J.APSUSC.2019.144450
Abstract: In this paper, we explore the electronic properties of C3N, C3N4 and C4N3 and graphene (Gr) van der Waals heterostructures by conducing extensive first-principles calculations. The acquired results show that these heterostructures can show diverse electronic properties, such as the metal (Gr on C3N), semiconductor with narrow band gap (Gr on C3N4) and ferromagnetic-metal (Gr on C4N3). We furthermore explored the effect of vacancies, atom substitution, topological, antisite and Stone-Wales defects on the structural and electronic properties of considered heterostructures. Our results show that the vacancy defects introduce localized states near the Fermi level and create a local magnetic moment. The Gr/C3N heterostructures with the single and double vacancy defects exhibit a ferromagnetic-metal, while Stone-Wales defects show an indirect semiconductor with the band gap of 0.2 eV. The effects of adsorption and insertion of O, C, Be, Cr, Fe and Co atoms on the electronic properties of Gr/C3N have been also elaborately studied. Our results highlight that the electronic and magnetic properties of garphene/carbon-nitride lateral heterostructures can be effectively modified by point defects and impurities.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 6.7
Times cited: 26
DOI: 10.1016/J.APSUSC.2019.144450
|
|
“Transmission electron microscopy study of complex oxide scales on DIN 1.4970 steel exposed to liquid Pb-Bi eutectic”. Charalampopoulou E, Delville R, Verwerft M, Lambrinou K, Schryvers D, Corrosion science 147, 22 (2019). http://doi.org/10.1016/j.corsci.2018.10.018
Abstract: The deployment of Gen-IV lead-cooled fast reactors requires a good compatibility between the selected structural/cladding steels and the inherently corrosive heavy liquid metal coolant. An effective liquid metal corrosion mitigation strategy involves the in-situ steel passivation in contact with the oxygen-containing Pb-alloy coolant. Transmission electron microscopy was used in this work to study the multi-layered oxide scales forming on an austenitic stainless steel fuel cladding exposed to oxygen-containing (CO ≈ 10−6 mass%) static liquid leadbismuth eutectic (LBE) for 1000 h between 400 and 500 °C. The oxide scale constituents were analyzed, including the intertwined phases comprising the innermost biphasic layer.
Keywords: A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
Times cited: 5
DOI: 10.1016/j.corsci.2018.10.018
|
|
“Transition energies of D- centers in a superlattice”. Shi JM, Peeters FM, Devreese JT, Surface science : a journal devoted to the physics and chemistry of interfaces 305, 220 (1994). http://doi.org/10.1016/0039-6028(94)90888-5
Keywords: A1 Journal article; Condensed Matter Theory (CMT); Theory of quantum systems and complex systems
Impact Factor: 1.925
Times cited: 6
DOI: 10.1016/0039-6028(94)90888-5
|
|
“Trace-level microanalysis of Roman glass from Khirbet Qumran, Israel”. Aerts A, Janssens K, Adams F, Journal of archaeological science 26, 883 (1999). http://doi.org/10.1006/JASC.1999.0397
Keywords: A1 Journal article; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation)
Impact Factor: 2.602
DOI: 10.1006/JASC.1999.0397
|
|
“Towards biolubricant compatible vegetable oils by pore mouth hydrogenation with shape-selective Pt/ZSM-5 catalysts”. Van Aelst J, Philippaerts A, Bartholomeeusen E, Fayad E, Thibault-Starzyk F, Lu J, Schryvers D, Ooms R, Verboekend D, Jacobs P, Sels B, Catalysis science &, technology 6, 2820 (2016). http://doi.org/10.1039/C6CY00498A
Abstract: Pt/ZSM-5 catalysts with various crystal sizes were prepared via competitive ion-exchange, followed by a slow activation procedure. Even when using very large ZSM-5 crystals, highly dispersed Pt nano-clusters were contained within the zeolite crystal's voids, as ascertained by 2D pressure-jump IR spectroscopy of adsorbed CO and focussed ion-beam transmission electron microscopy. The shape-selective properties of the Pt/ZSM-5 catalysts were evaluated in the partial hydrogenation of soybean oil. Unique hydrogenation selectivities were observed, as the fatty acids located at the central position of the triacylglycerol (TAG) molecules were preferentially hydrogenated. The resulting oil has therefore high levels of intermediately melting TAGs, which are compatible with biolubricants due to their improved oxidative stability and still appropriate low-temperature fluidity. The TAG distribution in the partially hydrogenated soybean oil samples was independent from the zeolite crystal size, while the hydrogenation activity linearly increases with the crystal's external surface area. This trend was confirmed with a Pt loaded mesoporous ZSM-5 zeolite, obtained via a mild alkaline treatment. These observations imply and confirm a genuine pore mouth catalysis mechanism, in which only one fatty acid chain of the TAG is able to enter the micropores of ZSM-5, where the double bonds are hydrogenated by the crystal encapsulated Pt-clusters.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 5.773
Times cited: 5
DOI: 10.1039/C6CY00498A
|
|
“Towards a novel strategy for soot removal from water-soluble materials : the synergetic effect of hydrogels and cyclomethicone on gelatine emulsion-based photographs”. Ortega Saez N, Arno R, Marchetti A, Cauberghs S, Janssens K, Van der Snickt G, Al-Emam E, Heritage science 11, 78 (2023). http://doi.org/10.1186/S40494-023-00916-5
Abstract: Gels are a popular cleaning method for paper conservators and a lot of research has been done concerning gel cleaning of paper objects over the last 15 years. Despite the close interconnection between the conservation fields of paper and photographic material, research on using gels for cleaning photographs is very scarce. However, gels can provide an excellent cleaning method for photographic material. Cleaning silver gelatine prints with aqueous solvents is very complex due to the hydrophilic properties and fragility of the gelatine layer which makes mechanical cleaning difficult. The properties of gels ensure better control over the flow and evaporation of the solvent, facilitating the cleaning process. This study is the first insight into the viability of using gellan gum gel and polyvinyl acetate-borax (PVAc-borax) gel to clean contaminants from the surface of silver gelatine photographs. It is based on self-made samples that were artificially aged and contaminated with soot. Water, ethanol (EtOH), and Kodak Photo-flo were studied as solvents to remove the soot from the silver gelatine-based prints. These solvents were loaded into the aforementioned gels and applied to the samples in two different methods. These gel cleaning methods were subsequently compared with traditional cleaning methods. In addition, the usage of cyclomethicone D4 as a protective mask for the gelatine layer was studied. Measuring methods used to evaluate the cleaning were visual comparison, microscopic observation, and densitometry. ATR-FTIR measurements were also conducted to investigate potential side-effects of the cleaning methods on the prints, such as unwanted chemical transformations or the presence of gel residues after the treatments. Most of the gel cleaning methods within this study proved to be inadequate, with the exception of the gellan gum gel loaded with 30% EtOH. It was used as a granulated gel applied mechanically on a print saturated with cyclomethicone (octamethylcyclotetrasiloxane D4). Cyclomethicone proved to be a very effective protective barrier for the water-sensitive gelatine layer with minimal reduction in cleaning effectiveness.
Keywords: A1 Journal article; Engineering sciences. Technology; Art; Antwerp Cultural Heritage Sciences (ARCHES); Antwerp X-ray Imaging and Spectroscopy (AXIS)
Impact Factor: 2.5
DOI: 10.1186/S40494-023-00916-5
|
|
“Tilted BaHfO3 nanorod artificial pinning centres in REBCO films on inclined substrate deposited-MgO coated conductor templates”. Stafford BH, Sieger M, Ottolinger R, Meledin A, Strickland NM, Wimbush SC, Van Tendeloo G, Huehne R, Schultz L, Superconductor science and technology 30, 055002 (2017). http://doi.org/10.1088/1361-6668/AA621D
Abstract: We grow BaHfO3 (BHO) nanorods in REBa2Cu3O7-x (REBCO, RE: Gd or Y) thin films on metal tapes coated with the inclined substrate deposited (ISD)-MgO template by both electron beam physical vapour deposition and pulsed laser deposition. In both cases the nanorods are inclined by an angle of 21 degrees-29 degrees with respect to the sample surface normal as a consequence of the tilted growth of the REBCO film resulting from the ISD-MgO layer. We present angular critical current density (J(c)) anisotropy as well as field- and temperature-dependant J(c) data of the BHO nanorod-containing GdBCO films demonstrating an increase in J(c) over a wide range of temperatures between 30 and 77 K and magnetic fields up to 8 T. In addition, we show that the angle of the peak in the J(c) anisotropy curve resulting from the nanorods is dependent both on temperature and magnetic field. The largest J(c) enhancement from the addition of the nanorods was found to occur at 30 K, 3 T, resulting in a J(c) of 3.0 MA cm(-2).
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 2.878
Times cited: 6
DOI: 10.1088/1361-6668/AA621D
|
|
“Three-dimensional modeling of energy transport in a gliding arc discharge in argon”. Kolev S, Bogaerts A, Plasma Sources Science &, Technology 27, 125011 (2018). http://doi.org/10.1088/1361-6595/aaf29c
Abstract: In this work we study energy transport in a gliding arc discharge with two diverging flat
electrodes in argon gas at atmospheric pressure. The discharge is ignited at the shortest electrode
gap and it is pushed downstream by a forced gas flow. The current values considered are
relatively low and therefore a non-equilibrium plasma is produced. We consider two cases, i.e.
with high and low discharge current (28 mA and 2.8mA), and a constant gas flow of 10 lmin −1 ,
with a significant turbulent component to the velocity. The study presents an analysis of the
various energy transport mechanisms responsible for the redistribution of Joule heating to the
plasma species and the moving background gas. The objective of this work is to provide a
general understanding of the role of the different energy transport mechanisms in arc formation
and sustainment, which can be used to improve existing or new discharge designs. The work is
based on a three-dimensional numerical model, combining a fluid plasma model, the shear stress
transport Reynolds averaged Navier–Stokes turbulent gas flow model, and a model for gas
thermal balance. The obtained results show that at higher current the discharge is constricted
within a thin plasma column several hundred kelvin above room temperature, while in the low-
current discharge the combination of intense convective cooling and low Joule heating prevents
discharge contraction and the plasma column evolves to a static non-moving diffusive plasma,
continuously cooled by the flowing gas. As a result, the energy transport in the two cases is
determined by different mechanisms. At higher current and a constricted plasma column, the
plasma column is cooled mainly by turbulent transport, while at low current and an unconstricted
plasma, the major cooling mechanism is energy transport due to non-turbulent gas convection. In
general, the study also demonstrates the importance of turbulent energy transport in
redistributing the Joule heating in the arc and its significant role in arc cooling and the formation
of the gas temperature profile. In general, the turbulent energy transport lowers the average gas
temperature in the arc, thus allowing additional control of thermal non-equilibrium in the
discharge.
Keywords: A1 Journal Article; gliding arc discharge, sliding arc discharge, energy transport, fluid plasma model, atmospheric pressure plasmas; Plasma, laser ablation and surface modeling Antwerp (PLASMANT) ;
Impact Factor: 3.302
DOI: 10.1088/1361-6595/aaf29c
|
|
“Thermal recrystallization of short-range ordered WS2 films”. Heyne MH, de Marneffe J-F, Radu I, Neyts EC, De Gendt S, Journal of vacuum science and technology: A: vacuum surfaces and films 36, 05g501 (2018). http://doi.org/10.1116/1.5036654
Abstract: The integration of van der Waals materials in nanoelectronic devices requires the deposition of few-layered MX2 films with excellent quality crystals covering a large area. In recent years, astonishing progress in the monolayer growth of WS2 and MoS2 was demonstrated, but multilayer growth resulted often in separated triangular or hexagonal islands. These polycrystalline films cannot fully employ the specific MX2 properties since they are not connected in-plane to the other domains. To coalesce separated islands, ultrahigh-temperature postdeposition anneals in H2S are applied, which are not compatible with bare silicon substrates. Starting from the deposition of stoichiometric short-ordered films, the present work studies different options for subsequent high-temperature annealing in an inert atmosphere to form crystalline films with large grains from stoichiometric films with small grains. The rapid thermal annealing, performed over a few seconds, is compared to excimer laser annealing in the nanosecond range, which are both able to crystallize the thin WS2. The WS2 recrystallization temperature can be lowered using metallic crystallization promoters (Co and Ni). The best result is obtained using a Co cap, due to the circumvention of Co and S binary phase formation below the eutectic temperature. The recrystallization above a critical temperature is accompanied by sulfur loss and 3D regrowth. These undesired effects can be suppressed by the application of a dielectric capping layer prior to annealing. A SiO2 cap can suppress the sulfur loss successfully during annealing and reveals improved material quality in comparison to noncapped films Published by the AVS.
Keywords: A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Impact Factor: 1.374
Times cited: 2
DOI: 10.1116/1.5036654
|
|
“Thermal instability and volume contraction in a pulsed microwave N2plasma at sub-atmospheric pressure”. Kelly S, van de Steeg A, Hughes A, van Rooij G, Bogaerts A, Plasma Sources Science &, Technology 30, 055005 (2021). http://doi.org/10.1088/1361-6595/abf1d6
Abstract: We studied the evolution of an isolated pulsed plasma in a vortex flow stabilised microwave (MW) discharge in N2 at 25 mbar via the combination of 0D kinetics modelling, iCCD imaging and laser scattering diagnostics. Quenching of electronically excited N2 results in fast gas heating and the onset of a thermal-ionisation instability, contracting the discharge volume. The onset of a thermal-ionisation instability driven by vibrational excitation pathways is found to facilitate significantly higher N2 conversion (i.e. dissociation to atomic N2 ) compared to pre-instability conditions, emphasizing the potential utility of this dynamic in future fixation applications. The instability onset is found to be instigated by super-elastic heating of the electron energy distribution tail via vibrationally excited N2 . Radial contraction of the discharge to the skin depth is found to occur post instability, while the axial elongation is found to be temporarily contracted during the thermal instability onset. An increase in power reflection during the thermal instability onset eventually limits the destabilising effects of exothermic electronically excited N2 quenching. Translational and vibrational temperature reach a quasi-non-equilibrium after the discharge contraction, with translational temperatures reaching ∼1200 K at the pulse end, while vibrational temperatures are found in near equilibrium with the electron energy (1 eV, or ∼11 600 K). This first description of the importance of electronically excited N2 quenching in thermal instabilities gives an additional fundamental understanding of N2 plasma behaviour in pulsed MW context, and thereby brings the eventual implementation of this novel N2 fixation method one step closer.
Keywords: A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Impact Factor: 3.302
DOI: 10.1088/1361-6595/abf1d6
|
|
“Thermal conductivity of titanium nitride/titanium aluminum nitride multilayer coatings deposited by lateral rotating cathode arc”. Samani MK, Ding XZ, Khosravian N, Amin-Ahmadi B, Yi Y, Chen G, Neyts EC, Bogaerts A, Tay BK, Thin solid films : an international journal on the science and technology of thin and thick films 578, 133 (2015). http://doi.org/10.1016/j.tsf.2015.02.032
Abstract: A seriesof [TiN/TiAlN]nmultilayer coatingswith different bilayer numbers n=5, 10, 25, 50, and 100 were deposited on stainless steel substrate AISI 304 by a lateral rotating cathode arc technique in a flowing nitrogen atmosphere. The composition and microstructure of the coatings have been analyzed by using energy dispersive X-ray spectroscopy, X-ray diffraction (XRD), and conventional and high-resolution transmission electron microscopy (HRTEM). XRD analysis shows that the preferential orientation growth along the (111) direction is reduced in the multilayer coatings. TEM analysis reveals that the grain size of the coatings decreases with increasing bilayer number. HRTEMimaging of the multilayer coatings shows a high density misfit dislocation between the TiN and TiAlN layers. The cross-plane thermal conductivity of the coatings was measured by a pulsed photothermal reflectance technique. With increasing bilayer number, the multilayer coatings' thermal conductivity decreases gradually. This reduction of thermal conductivity can be ascribed to increased phonon scattering due to the disruption of columnar structure, reduced preferential orientation, decreased grain size of the coatings and present misfit dislocations at the interfaces.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT); Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Impact Factor: 1.879
Times cited: 41
DOI: 10.1016/j.tsf.2015.02.032
|
|
“Thermal conductivity engineering of bulk and one-dimensional Si-Ge nanoarchitectures”. Kandemir A, Ozden A, Cagin T, Sevik C, Science and technology of advanced materials 18, 187 (2017). http://doi.org/10.1080/14686996.2017.1288065
Abstract: Various theoretical and experimental methods are utilized to investigate the thermal conductivity of nanostructured materials; this is a critical parameter to increase performance of thermoelectric devices. Among these methods, equilibrium molecular dynamics (EMD) is an accurate technique to predict lattice thermal conductivity. In this study, by means of systematic EMD simulations, thermal conductivity of bulk Si-Ge structures (pristine, alloy and superlattice) and their nanostructured one dimensional forms with square and circular cross-section geometries (asymmetric and symmetric) are calculated for different crystallographic directions. A comprehensive temperature analysis is evaluated for selected structures as well. The results show that one-dimensional structures are superior candidates in terms of their low lattice thermal conductivity and thermal conductivity tunability by nanostructuring, such as by diameter modulation, interface roughness, periodicity and number of interfaces. We find that thermal conductivity decreases with smaller diameters or cross section areas. Furthermore, interface roughness decreases thermal conductivity with a profound impact. Moreover, we predicted that there is a specific periodicity that gives minimum thermal conductivity in symmetric superlattice structures. The decreasing thermal conductivity is due to the reducing phonon movement in the system due to the effect of the number of interfaces that determine regimes of ballistic and wave transport phenomena. In some nanostructures, such as nanowire superlattices, thermal conductivity of the Si/Ge system can be reduced to nearly twice that of an amorphous silicon thermal conductivity. Additionally, it is found that one crystal orientation, <100>, is better than the <111> crystal orientation in one-dimensional and bulk SiGe systems. Our results clearly point out the importance of lattice thermal conductivity engineering in bulk and nanostructures to produce high-performance thermoelectric materials.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
DOI: 10.1080/14686996.2017.1288065
|
|
“Theoretical aspects of graphene-like group IV semiconductors”. Houssa M, van den Broek B, Scalise E, Ealet B, Pourtois G, Chiappe D, Cinquanta E, Grazianetti C, Fanciulli M, Molle A, Afanas’ev VV, Stesmans A;, Applied surface science 291, 98 (2014). http://doi.org/10.1016/j.apsusc.2013.09.062
Abstract: Silicene and germanene are the silicon and germanium counterparts of graphene, respectively. Recent experimental works have reported the growth of silicene on (1 1 1)Ag surfaces with different atomic configurations, depending on the growth temperature and surface coverage. We first theoretically study the structural and electronic properties of silicene on (1 1 1) Ag surfaces, focusing on the (4 x 4) silicene/Ag structure. Due to symmetry breaking in the silicene layer (nonequivalent number of top and bottom Si atoms), the corrugated silicene layer, with the Ag substrate removed, is predicted to be semiconducting, with a computed energy bandgap of about 0.3 eV. However, the hybridization between the Si 3p orbitals and the Ag 5s orbital in the silicene/(1 1 1)Ag slab model leads to an overall metallic system, with a distribution of local electronic density of states, which is related to the slightly disordered structure of the silicene layer on the (1 1 1)Ag surface. We next study the interaction of silicene and germanene with different hexagonal non-metallic substrates, namely ZnS and ZnSe. On reconstructed (0 0 0 1)ZnS or ZnSe surfaces, which should be more energetically stable for very thin layers, silicene and germanene are found to be semiconducting. Remarkably, the nature and magnitude of their energy bandgap can be controlled by an out-of-plane electric field, an important finding for the potential use of these materials in nanoelectronic devices. (C) 2013 Elsevier B. V. All rights reserved.
Keywords: A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Impact Factor: 3.387
Times cited: 20
DOI: 10.1016/j.apsusc.2013.09.062
|
|
“The young Van Dyck's fingerprint : a technical approach to assess the authenticity of a disputed painting”. Harth A, van der Snickt G, Schalm O, Janssens K, Blanckaert G, Heritage science 5, 22 (2017). http://doi.org/10.1186/S40494-017-0136-3
Abstract: The painting Saint Jerome, part of the collection of the Maagdenhuis Museum (Antwerp, Belgium), is attributed to the young Anthony van Dyck (1613-1621) with reservations. The painting displays remarkable compositional and iconographic similarities with two early Van Dyck works (1618-1620) now in Museum Boijmans van Beuningen (Rotterdam) and Nationalmuseum (Stockholm). Despite these similarities, previous art historical research did not result in a clear attribution to this master. In this study, the works authenticity as a young Van Dyck painting was assessed from a technical perspective by employing a twofold approach. First, technical information on Van Dycks materials and techniques, here identified as his fingerprint, were defined based on a literature review. Second, the materials and techniques of the questioned Saint Jerome painting were characterized by using complementary imaging techniques: infrared reflectography, X-ray radiography and macro X-ray fluorescence scanning. The insights from this non-invasive research were supplemented with analysis of a limited number of cross-sections by means of field emission scanning electron microscopy coupled with energy dispersive X-ray spectroscopy. The results demonstrated that the questioned paintings materials and techniques deviate from Van Dycks fingerprint, thus making the authorship of this master very unlikely.
Keywords: A1 Journal article; Art; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation); Antwerp Cultural Heritage Sciences (ARCHES)
Times cited: 1
DOI: 10.1186/S40494-017-0136-3
|