“A simple absorption correction for electron probe X-ray microanalysis of bulk samples”. Markowicz A, Storms H, Van Grieken R, X-ray spectrometry 15, 115 (1986). http://doi.org/10.1002/XRS.1300150209
Abstract: A simple procedure is proposed for the calculation of the absorption correction factor in electron-probe x-ray microanalysis. It is based on the concept of an effective depth of x-ray production, assuming a rectangular depth distribution function for x-ray generation. This effective x-ray production depth is expressed as a fraction of the x-ray excitation depth given by Whelan's expression. Adequate values for this fraction are presented. Two versions are considered. In the first the effective x-ray production is a function of both the characteristic x-ray energy and the atomic numbers of the matrix elements, whereas in the second one, which is indicated for routine use, the energy dependence is neglected. Calculations pointed to satisfactory results, even for low x-ray energies and high overvoltages.
Keywords: A1 Journal article; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation)
DOI: 10.1002/XRS.1300150209
|
“A seasonal study of atmospheric conditions influenced by the intensive tourist flow in the Royal Museum of Wawel Castle in Cracow, Poland”. Worobiec A, Samek L, Karaszkiewicz P, Kontozova-Deutsch V, Stefaniak EA, van Meel K, Krata A, Bencs L, Van Grieken R, Microchemical journal 90, 99 (2008). http://doi.org/10.1016/J.MICROC.2008.04.005
Abstract: Increasingmass tourismcan generate importantmicroclimatic perturbations and also elevate indoor pollution by the transport of fine particulatematter. The purpose of this researchwas to study the indoor air conditions in the RoyalMuseum ofWawel Castle in Cracow, Poland, displaying amongst other valuable works of art also a unique collection of Flemish tapestries. The investigation involved in the determination of transport and deposition of particulate matter brought in by visitors. The microclimate inside the exhibition rooms was also monitored. Samples of suspended particulateswere collected inside and outside themuseuminwinterand summer2006.On days with intensive tourist visits the concentration of total suspended particulates was significantly higher (i.e., 130 µg/m3 inwinter and 49 µg/m3 in summer) than on those days without tourists (i.e., 73 µg/m3 and 22 µg/m3 in winter and summer, respectively). The concentrations of all investigated elementswere also considerably higher during the tourist flow. This was especially valid for soil dust associated elements (Si, K, Ca, Al, and Ti), with considerably higher levels in summer than winter. This could be linked with much more frequent tourist activity in the summer period. Also, the concentration of Clwasmuch higher inwinter than summer, due to the use of deicing salts on the roads and pavements.
Keywords: A1 Journal article; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation); Laboratory Experimental Medicine and Pediatrics (LEMP)
DOI: 10.1016/J.MICROC.2008.04.005
|
“A robust nitrifying community in a bioreactor at 50 degrees C opens up the path for thermophilic nitrogen removal”. Courtens ENP, Spieck E, Vilchez-Vargas R, Bode S, Boeckx P, Schouten S, Jauregui R, Pieper DH, Vlaeminck SE, Boon N, The ISME journal : multidisciplinary journal of microbial ecology 10, 2293 (2016). http://doi.org/10.1038/ISMEJ.2016.8
Abstract: The increasing production of nitrogen-containing fertilizers is crucial to meet the global food demand, yet high losses of reactive nitrogen associated with the food production/consumption chain progressively deteriorate the natural environment. Currently, mesophilic nitrogen-removing microbes eliminate nitrogen from wastewaters. Although thermophilic nitrifiers have been separately enriched from natural environments, no bioreactors are described that couple these processes for the treatment of nitrogen in hot wastewaters. Samples from composting facilities were used as inoculum for the batch-wise enrichment of thermophilic nitrifiers (350 days). Subsequently, the enrichments were transferred to a bioreactor to obtain a stable, high-rate nitrifying process (560 days). The community contained up to 17% ammonia-oxidizing archaea (AOAs) closely related to 'Candidatus Nitrososphaera gargensis', and 25% nitrite-oxidizing bacteria (NOBs) related to Nitrospira calida. Incorporation of C-13-derived bicarbonate into the respective characteristic membrane lipids during nitrification supported their activity as autotrophs. Specific activities up to 198 +/- 10 and 894 +/- 81 mg N g(-1) VSS per day for AOAs and NOBs were measured, where NOBs were 33% more sensitive to free ammonia. The NOBs were extremely sensitive to free nitrous acid, whereas the AOAs could only be inhibited by high nitrite concentrations, independent of the free nitrous acid concentration. The observed difference in product/substrate inhibition could facilitate the development of NOB inhibition strategies to achieve more cost-effective processes such as deammonification. This study describes the enrichment of autotrophic thermophilic nitrifiers from a nutrient-rich environment and the successful operation of a thermophilic nitrifying bioreactor for the first time, facilitating opportunities for thermophilic nitrogen removal biotechnology.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1038/ISMEJ.2016.8
|
“A robust evolutionary algorithm for the recovery of rational Gielis curves”. Fougerolle YD, Truchetet F, Demonceaux C, Gielis J, Pattern recognition 46, 2078 (2013). http://doi.org/10.1016/J.PATCOG.2013.01.024
Abstract: Gielis curves (GC) can represent a wide range of shapes and patterns ranging from star shapes to symmetric and asymmetric polygons, and even self intersecting curves. Such patterns appear in natural objects or phenomena, such as flowers, crystals, pollen structures, animals, or even wave propagation. Gielis curves and surfaces are an extension of Lamé curves and surfaces (superquadrics) which have benefited in the last two decades of extensive researches to retrieve their parameters from various data types, such as range images, 2D and 3D point clouds, etc. Unfortunately, the most efficient techniques for superquadrics recovery, based on deterministic methods, cannot directly be adapted to Gielis curves. Indeed, the different nature of their parameters forbids the use of a unified gradient descent approach, which requires initial pre-processings, such as the symmetry detection, and a reliable pose and scale estimation. Furthermore, even the most recent algorithms in the literature remain extremely sensitive to initialization and often fall into local minima in the presence of large missing data. We present a simple evolutionary algorithm which overcomes most of these issues and unifies all of the required operations into a single though efficient approach. The key ideas in this paper are the replacement of the potential fields used for the cost function (closed form) by the shortest Euclidean distance (SED, iterative approach), the construction of cost functions which minimize the shortest distance as well as the curve length using R-functions, and slight modifications of the evolutionary operators. We show that the proposed cost function based on SED and R-function offers the best compromise in terms of accuracy, robustness to noise, and missing data.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1016/J.PATCOG.2013.01.024
|
“A Ricardian analysis of climate change impacts on Japan's agriculture : accounting for solar radiation”. Okamura I, Van Passel S, Fabri C, Senda T, Climate change economics 14, 2350022 (2023). http://doi.org/10.1142/S2010007823500227
Abstract: This study evaluates the effects of climate change on the net revenue of farmers in Japan. We adopted the Ricardian model, which implicitly accounts for farmers’ full adaptation. The main findings of this study are as follows. First, the Ricardian regression shows that changes in temperature significantly impact farmers’ net revenue. In contrast, changes in precipitation have limited effects on farmers’ net revenue. The results of future predictions showed that the effects of climate change are positive across the country, with varying degrees between north and south. These results are more optimistic than those in the existing literature, which frequently reveal negative climate change impacts in southern Japan. However, it should be noted that this model assumes full adaptation and does not consider the transition costs of farmers, and understanding the actual adaptive measures is an important remaining issue.
Keywords: A1 Journal article; Economics; Engineering Management (ENM)
DOI: 10.1142/S2010007823500227
|
“A review on the leaf area index (LAI) in vertical greening systems”. De Bock A, Belmans B, Vanlanduit S, Blom J, Alvarado Alvarado AA, Audenaert A, Building and environment 229, 109926 (2023). http://doi.org/10.1016/J.BUILDENV.2022.109926
Abstract: The leaf area index (LAI) is a key dynamic parameter in Vertical Greening Systems (VGS). It quantifies the total amount of leaf area in the canopy and largely determines the extent of co-benefits of VGS. Whereas many studies on VGS discuss the importance of the LAI, only few elaborate on the parameter itself, how it is determined and what the current limitations are in VGS. Moreover, although there is scientific consensus on the importance of LAI in VGS, specific non-destructive monitoring techniques for continuous LAI monitoring appear to be absent, which results in limited overall data on the LAI of VGS under different spatial and temporal conditions and problems in quantifying the benefits of VGS in practice. To fill these gaps, this paper specifically focuses on the LAI of VGS and its monitoring techniques. An overview of existing LAI monitoring techniques in the field of VGS is presented. To arrive at dedicated techniques, this is complemented by a thorough analysis of LAI monitoring techniques used in other research fields, e.g. agriculture and forestry. It is established that two indirect techniques for LAI monitoring are currently available in the VGS sector, but a proper standardized sampling methodology currently lacks. Monitoring techniques used in other sectors offer opportunities for developing dedicated monitoring methods for VGS, but require further research due to the specific features of VGS systems. Furthermore, guidelines are proposed for a more standardized LAI determination of reporting of LAI values in VGS.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL); Sustainable Pavements and Asphalt Research (SuPAR); Energy and Materials in Infrastructure and Buildings
Impact Factor: 7.4
DOI: 10.1016/J.BUILDENV.2022.109926
|
“A review on self‐assembly of colloidal nanoparticles into clusters, patterns, and films : emerging synthesis techniques and applications”. Borah R, Ag KR, Minja AC, Verbruggen SW, Small methods , 1 (2023). http://doi.org/10.1002/SMTD.202201536
Abstract: The colloidal synthesis of functional nanoparticles has gained tremendous scientific attention in the last decades. In parallel to these advancements, another rapidly growing area is the self-assembly or self-organization of these colloidal nanoparticles. First, the organization of nanoparticles into ordered structures is important for obtaining functional interfaces that extend or even amplify the intrinsic properties of the constituting nanoparticles at a larger scale. The synthesis of large-scale interfaces using complex or intricately designed nanostructures as building blocks, requires highly controllable self-assembly techniques down to the nanoscale. In certain cases, for example, when dealing with plasmonic nanoparticles, the assembly of the nanoparticles further enhances their properties by coupling phenomena. In other cases, the process of self-assembly itself is useful in the final application such as in sensing and drug delivery, amongst others. In view of the growing importance of this field, this review provides a comprehensive overview of the recent developments in the field of nanoparticle self-assembly and their applications. For clarity, the self-assembled nanostructures are classified into two broad categories: finite clusters/patterns, and infinite films. Different state-of-the-art techniques to obtain these nanostructures are discussed in detail, before discussing the applications where the self-assembly significantly enhances the performance of the process.
Keywords: A1 Journal article; Engineering sciences. Technology
Impact Factor: 12.4
DOI: 10.1002/SMTD.202201536
|
“A review of technological solutions to prevent or reduce marine plastic litter in developing countries”. Winterstetter A, Grodent M, Kini V, Ragaert K, Vrancken KCM, Sustainability 13, 4894 (2021). http://doi.org/10.3390/SU13094894
Abstract: Growing global plastic production combined with poor waste collection has led to increasing amounts of plastic debris being found in oceans, rivers and on shores. The goal of this study is to provide an overview on currently available technological solutions to tackle marine plastic litter and to assess their potential use in developing countries. To compile an inventory of technological solutions, a dedicated online platform was developed. A total of 51 out of initially 75 submitted solutions along the plastics value chain were assessed by independent experts. Collection systems represent more than half of the shortlisted solutions. A quarter include processing and treatment technologies, either as a stand-alone solution (30%) or, more commonly, in combination with a first litter capturing step. Ten percent offer digital solutions. The rest focuses on integrated waste management solutions. For each stage in the source-to-sea spectrum-land, rivers, sea-two illustrative examples are described in detail. This study concludes that the most cost-effective type of solution tackles land-based sources of marine litter and combines technology with people-oriented practices, runs on own energy sources, connects throughout the plastics value chain with a convincing valorization plan for captured debris, and involves all relevant stakeholders.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 1.789
DOI: 10.3390/SU13094894
|
Vermeulen S, Cools J, Staes J, Van Passel S (2023) A review of economic assessments of drought risk reduction approaches in agriculture. 118909–118912
Abstract: Due to climate change, the frequency and intensity of droughts are expected to increase. To improve resilience to droughts, proactive drought management is essential. Economic assessments are typically included to decide on the drought risk-reducing investments to make. The choice of both methods and scope of economic assessments influences the outcome, and thus the investment choice. This paper aims to identify how comprehensively economic assessments are applied in practice. Through a systematic literature review, 14 actual economic assessments are identified and their methods are evaluated based on seven criteria for economic assessments as derived from the United Nations Framework Convention on Climate Change (UNFCCC). The results show that in practice, economic assessments rarely address all criteria. Applying a limited number of criteria reduces the scope and narrows the approach, possibly leading to the underestimation of drought risk reduction approaches’ related benefits. Applying the seven criteria in practice will improve the results of economic assessments of drought risk reduction measures, allowing for optimal investment selection. Based on the different criteria, a Framework for Economic Assessments of Drought Risk-Reducing Applications (FEADRRA) is proposed. Applying the criteria of the framework can support decision-makers in drought risk management and in carrying out the most fitting drought interventions.
Keywords: Administrative Services; A1 Journal article; Economics; Ecosphere; Engineering Management (ENM)
Impact Factor: 8.7
DOI: 10.1016/J.JENVMAN.2023.118909
|
“A real-world analysis on the efficacy and tolerability of liposomal irinotecan plus 5-fluorouracil and folinic acid in metastatic pancreatic ductal adenocarcinoma in Belgium”. Verbruggen L, Verheggen L, Vanhoutte G, Loly C, Lybaert W, Borbath I, Vergauwe P, Hendrickx K, Debeuckelaere C, de Haar-Holleman A, Van Laethem J-L, Peeters M, Therapeutic advances in medical oncology 15, 1 (2023). http://doi.org/10.1177/17588359231181500
Abstract: Background: Currently, nanoliposomal irinotecan (nal-IRI) + 5-fluorouracil/folinic acid (5-FU/ LV) is the only approved second-line treatment for patients suffering from metastatic pancreatic ductal adenocarcinoma (mPDAC). However, also other chemotherapeutic regimens are used in this setting and due to the lack of clear real-world data on the efficacy of the different regimens, there is no consensus on the optimal treatment sequence for mPDAC patients. Objectives: To provide information on the safe and efficacious use of nal-IRI + 5-FU/LV in clinical practice in Belgium, which is needed for healthcare professionals to estimate the risk-benefit ratio of the intervention. Methods: Medical data of adult patients with mPDAC who were treated with nal-IRI + 5-FU/ LV in one of the participating Belgian hospitals were retrospectively collected. Kaplan-Meier analysis was performed to obtain survival curves to estimate the median overall survival (OS) and progression-free survival (PFS). All other results were presented descriptively. Results: A total of 56 patients [median age at diagnosis: 69 years (range 43 years), 57.1% male] were included. Patients received a median of 5 (range 49 cycles) nal-IRI + 5-FU/LV cycles, extended over 10 weeks (range 130.8 weeks). The median start dose for nal-IRI was 70 mg/ m(2) (range 49.24 mg/m(2)) and chemotherapy dose reduction and delay occurred in, respectively, 42.8% and 37.5% of the patients. The median OS was 6.8 months (95% CI: 5.6-8.4 months) with a 6-month survival rate of 57.4% and a 1-year survival rate of 27.8% in the overall study population. The median OS for patients treated with nal-IRI as second-line therapy or as laterline treatment was, respectively, 6.8 months (95% CI: 5.9-7.0 months) and 5.6 months (95% CI: 4.2-no upper limit). In the overall study population, a median PFS of 3.1 months (95% CI: 2.4-4.6 months) and a disease control rate of 48.3%, comprising 30.4% stable disease, 16.1% partial and 1.8% complete response, was observed. The median PFS for patients treated with nal-IRI as second-line therapy was 3.9 months (95% CI: 2.8-4.8 months) while this was 2.4 months (95% CI: 1.9-9.1 months) for those that received nal-IRI in a later-line treatment. In terms of safety, gastrointestinal problems occurred most (64.3% of the patients) and from all reported treatment emergent adverse events, 39.2% were grade 3 or 4. Conclusion: Nal-IRI + 5-FU/LV is a valuable, effective, and safe sequential treatment option following gemcitabine-based therapy in patients with mPDAC.
Keywords: A1 Journal article; Center for Oncological Research (CORE)
Impact Factor: 4.9
DOI: 10.1177/17588359231181500
|
“A qualitative model structure sensitivity analysis method to support model selection”. Van Hoey S, Seuntjens P, van der Kwast J, Nopens I, Journal of hydrology 519, 3426 (2014). http://doi.org/10.1016/J.JHYDROL.2014.09.052
Abstract: The selection and identification of a suitable hydrological model structure is a more challenging task than fitting parameters of a fixed model structure to reproduce a measured hydrograph. The suitable model structure is highly dependent on various criteria, i.e. the modeling objective, the characteristics and the scale of the system under investigation and the available data. Flexible environments for model building are available, but need to be assisted by proper diagnostic tools for model structure selection. This paper introduces a qualitative method for model component sensitivity analysis. Traditionally, model sensitivity is evaluated for model parameters. In this paper, the concept is translated into an evaluation of model structure sensitivity. Similarly to the one-factor-at-a-time (OAT) methods for parameter sensitivity, this method varies the model structure components one at a time and evaluates the change in sensitivity towards the output variables. As such, the effect of model component variations can be evaluated towards different objective functions or output variables. The methodology is presented for a simple lumped hydrological model environment, introducing different possible model building variations. By comparing the effect of changes in model structure for different model objectives, model selection can be better evaluated. Based on the presented component sensitivity analysis of a case study, some suggestions with regard to model selection are formulated for the system under study: (1) a non-linear storage component is recommended, since it ensures more sensitive (identifiable) parameters for this component and less parameter interaction; (2) interflow is mainly important for the low flow criteria; (3) excess infiltration process is most influencing when focussing on the lower flows; (4) a more simple routing component is advisable; and (5) baseflow parameters have in general low sensitivity values, except for the low flow criteria. (C) 2014 Elsevier B.V. All rights reserved.
Keywords: A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1016/J.JHYDROL.2014.09.052
|
“A practical guide to build a Raspberry Pi Pico based potentiostat for educational electrochemistry and electronic instrumentation”. Steijlen A, Docter M, Bastemeijer J, Topyla M, Moraczewska M, Hoekstra T, Parrilla M, De Wael K, Journal of chemical education (2024). http://doi.org/10.1021/ACS.JCHEMED.4C00624
Abstract: This manuscript presents the first practical guide to build a Raspberry Pi Pico based potentiostat for electrical and electrochemical instrumentation education. The circuit enables us to perform different types of voltammetry such as cyclic and square wave voltammetry. Voltammograms of paracetamol tablets in a neutral buffer solution were successfully recorded and compared to lab equipment. Thereafter, the effect of different scan rates and different concentrations was studied as a proof of concept. Furthermore, the experiments were expanded with measurements of other pharmaceutical tablets such as vitamin C. Over 80 nanobiology bachelor students successfully built their own potentiostat in an electronic instrumentation course. They validated their systems successfully with electrochemical experiments using paracetamol as a conventional pharmaceutical that can be performed in a classroom. The students acquired a valuable understanding of the electronic building blocks and system architecture within electrochemical instrumentation, equipping them with the requisite knowledge to effectively optimize instrumentation parameters in their future research work.
Keywords: A1 Journal article; Antwerp Electrochemical and Analytical Sciences Lab (A-Sense Lab); Antwerp engineering, PhotoElectroChemistry & Sensing (A-PECS)
Impact Factor: 3
DOI: 10.1021/ACS.JCHEMED.4C00624
|
“A Pareto aggregation approach for environmental-economic multi-objective optimization applied on a second-generation bioethanol production model”. Vasilakou K, Billen P, Van Passel S, Nimmegeers P, Energy conversion and management 303, 118184 (2024). http://doi.org/10.1016/J.ENCONMAN.2024.118184
Abstract: Multi-objective optimization is an important decision-making tool for energy processes, as multiple targets need to be achieved. These objectives are usually conflicting since a single solution cannot be optimal for all objectives, resulting in a set of Pareto-optimal solutions. Multiple indicators might be available to describe a sustainability objective, such as the environmental impact which is commonly evaluated by performing a life cycle assessment. In this study, Pareto aggregation is proposed as a method which employs a novel multi-objective optimization-based approach as an alternative to the classically used aggregation in life cycle assessment. This method identifies conflicting environmental indicators and performs an aggregation among those that require a trade-off. An environmental-economic optimization of a second-generation bioethanol plant is used to illustrate and evaluate the proposed method. Process parameters from a biochemical conversion pathway flowsheet simulation model are chosen as optimization variables. To reduce the computational time, surrogate models, based on artificial neural networks, are used. Out of the eighteen ReCiPe Midpoint environmental indicators, five were identified as conflicting, resulting in an aggregated environmental objective, which was then traded off with the economic objective function, chosen as the levelized cost of ethanol. Comparison with the widely used single-score EcoIndicator99 showed that the Pareto aggregation method can reduce most of the environmental indicators by up to 6.5%. This research provides an insight on non-redundant objective functions, aiming at reducing the dimensionality of multi-objective optimization problems, while taking into consideration decision-makers’ preferences.
Keywords: A1 Journal article; Economics; Engineering sciences. Technology; Engineering Management (ENM); Intelligence in PRocesses, Advanced Catalysts and Solvents (iPRACS)
Impact Factor: 10.4
DOI: 10.1016/J.ENCONMAN.2024.118184
|
“A novel mechanistic modelling approach for microbial selection dynamics : towards improved design and control of raceway reactors for purple bacteria”. Alloul A, Moradvandi A, Puyol D, Molina R, Gardella G, Vlaeminck SE, De Schutter B, Abraham E, Lindeboom REF, Weissbrodt DG, Bioresource technology 390, 129844 (2023). http://doi.org/10.1016/J.BIORTECH.2023.129844
Abstract: Purple phototrophic bacteria (PPB) show an underexplored potential for resource recovery from wastewater. Raceway reactors offer a more affordable full-scale solution on wastewater and enable useful additional aerobic processes. Current mathematical models of PPB systems provide useful mechanistic insights, but do not represent the full metabolic versatility of PPB and thus require further advancement to simulate the process for technology development and control. In this study, a new modelling approach for PPB that integrates the photoheterotrophic, and both anaerobic and aerobic chemoheterotrophic metabolic pathways through an empirical parallel metabolic growth constant was proposed. It aimed the modelling of microbial selection dynamics in competition with aerobic and anaerobic microbial community under different operational scenarios. A sensitivity analysis was carried out to identify the most influential parameters within the model and calibrate them based on experimental data. Process perturbation scenarios were simulated, which showed a good performance of the model.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 11.4
DOI: 10.1016/J.BIORTECH.2023.129844
|
“A note on spirals and curvature”. Gielis J, Caratelli D, Shi P, Ricci PE, Growth and form 1, 1 (2020). http://doi.org/10.2991/GAF.K.200124.001
Abstract: Starting from logarithmic, sinusoidal and power spirals, it is shown how these spirals are connected directly with Chebyshev polynomials, Lamé curves, with allometry and Antonelli-metrics in Finsler geometry. Curvature is a crucial concept in geometry both for closed curves and equiangular spirals, and allowed Dillen to give a general definition of spirals. Many natural shapes can be described as a combination of one of two basic shapes in nature—circle and spiral—with Gielis transformations. Using this idea, shape description itself is used to develop a novel approach to anisotropic curvature in nature. Various examples are discussed, including fusion in flowers and its connection to the recently described pseudo-Chebyshev functions.
Keywords: A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.2991/GAF.K.200124.001
|
“A note on Generalized Möbius-Listing Bodies”. Gielis J, Tavkhelidze I, , 31 (2023). http://doi.org/10.55060/s.atmps.231115.003
Abstract: Generalized Möbius-Listing surfaces and bodies generalize Möbius bands, and this research was motivated originally by solutions of boundary value problems. Analogous to cutting of the original Möbius band, for this class of surfaces and bodies, results have been obtained when cutting such bodies or surfaces. In general, cutting leads to interlinked and intertwined different surfaces or bodies, resulting in very complex systems. However, under certain conditions, the result of cutting can be a single surface or body, which reduces complexity considerably. These conditions are based on congruence and rotational symmetry of the resulting cross sections after cutting, and on the knife cutting the origin
Keywords: P1 Proceeding; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.55060/s.atmps.231115.003
|
“A note about generalized forms of the Gielis formula”. Gielis J, Natalini P, Ricci PE page 107 (2017).
Abstract: We generalize the Gielis Superformula by extending the R. Chacon approach, but avoiding the use of Jacobi elliptic functions. The obtained results are extended to the three-dimensional case. Several new shapes are derived by using the computer algebra system Mathematica(C).
Keywords: H1 Book chapter; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.2991/978-94-6239-261-8_8
|
“A new sulfolane based solvent for CO₂, capture”. Wagaarachchige J, Idris Z, Kummamuru NB, Sætre KA, Halstensen M, Jens K-J, SSRN electronic journal (2021). http://doi.org/10.2139/SSRN.3817192
Abstract: This study presents novel sulfolane based non-aqueous CO2 capture solvents, as an alternative solution for capturing CO2 from industrial processes. In order to select the most promising amine system, five different amines were tested by monitoring CO2 absorption and desorption processes using the time-base Attenuated Total Reflectance-Fourier Transform Infrared (ATR-FTIR) spectroscopy. During absorption experiments, we observed the formation of Monomethyl Carbonate (MMC) in diisopropylamine (DIPA) and 2-amino-2-methyl-1-propanol (AMP) systems, while carbamate was observed as the main product for the other three amine systems tested. In regeneration experiments, the MMC could be desorbed relatively easily from the amine solution at a mild temperature.
Keywords: P1 Proceeding; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.2139/SSRN.3817192
|
“A new program to estimate the parameters of Preston's equation, a general formula for describing the egg shape of birds”. Shi P, Wang L, Quinn BKK, Gielis J, Symmetry 15, 231 (2023). http://doi.org/10.3390/SYM15010231
Abstract: Preston's equation is a general model describing the egg shape of birds. The parameters of Preston's equation are usually estimated after re-expressing it as the Todd-Smart equation and scaling the egg's actual length to two. This method assumes that the straight line through the two points on an egg's profile separated by the maximum distance (i.e., the longest axis of an egg's profile) is the mid-line. It hypothesizes that the photographed egg's profile is perfectly bilaterally symmetrical, which seldom holds true because of photographic errors and placement errors. The existing parameter estimation method for Preston's equation considers an angle of deviation for the longest axis of an egg's profile from the mid-line, which decreases prediction errors to a certain degree. Nevertheless, this method cannot provide an accurate estimate of the coordinates of the egg's center, and it leads to sub-optimal parameter estimation. Thus, it is better to account for the possible asymmetry between the two sides of an egg's profile along its mid-line when fitting egg-shape data. In this paper, we propose a method based on the optimization algorithm (optimPE) to fit egg-shape data and better estimate the parameters of Preston's equation by automatically searching for the optimal mid-line of an egg's profile and testing its validity using profiles of 59 bird eggs spanning a wide range of existing egg shapes. We further compared this method with the existing one based on multiple linear regression (lmPE). This study demonstrated the ability of the optimPE method to estimate numerical values of the parameters of Preston's equation and provide the theoretical egg length (i.e., the distance between two ends of the mid-line of an egg's profile) and the egg's maximum breadth. This provides a valuable approach for comparing egg shapes among conspecifics or across different species, or even different classes (e.g., birds and reptiles), in future investigations.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 2.7
DOI: 10.3390/SYM15010231
|
“A new method to compensate for counting losses due to system dead time”. Karabidak SM, Čevik U, Kaya S, Nuclear instruments and methods in physics research : A: accelerators, spectrometers, detectors and associated equipment 603, 361 (2009). http://doi.org/10.1016/J.NIMA.2009.02.005
Abstract: Determination of count losses and pile-up pulse effects in quantitative and qualitative analysis became a vital step in various analyses. Therefore, compensating for counting losses is of importance. These counting losses are due to the pulse pile-up, paralyzable and non-paralyzable system dead time or a combination of these mechanisms. In this work, a new method is suggested for the correction of dead time losses resulting from the above mechanisms. For this purpose, a source code was developed. It was found that the peaking time was an important parameter over system dead time. The method suggested seems to be more effective even at high count rate. (C) 2009 Elsevier B.V. All rights reserved.
Keywords: A1 Journal article; Engineering sciences. Technology; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation)
DOI: 10.1016/J.NIMA.2009.02.005
|
“A new method for the evaluation of the reversible and irreversible fouling propensity of MBR mixed liquor”. Huyskens C, Brauns E, van Hoof E, de Wever H, Journal of membrane science 323, 185 (2008). http://doi.org/10.1016/J.MEMSCI.2008.06.021
Abstract: In this paper, a new fouling measurement method is presented as a pragmatic approach to determine a mixed liquor's fouling propensity. The MBR-VFM (VITO Fouling Measurement) uses a specific measurement protocol consisting of alternating filtration and physical cleaning steps, which enables the calculation of both the reversible and the irreversible fouling resistances. The MBR-VFM principle, set-up and measurement protocol are described as well as the evaluation of the fouling measurement method. Finally, the MBR-VFM was validated by comparing the fouling propensity measured on-line by the MBR-VFM in a lab-scale MBR with the fouling of the MBR membranes themselves. Our experiments indicated that the MBR-VFM can accurately measure fouling and that it can even be detected earlier than can be seen from the on-line filtration data of the lab-scale system itself. Furthermore, the differences measured in reversible and irreversible fouling seemed to be related to the observed impact of physical and chemical cleaning respectively. Therefore, the application of the MBR-VFM as an on-line sensor in an advanced control system, enabling the deployment of the measured fouling data for the control of membrane cleaning, seems feasible and will be tested in the near future.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1016/J.MEMSCI.2008.06.021
|
“A new healing strategy for metals : programmed damage and repair”. Arseenko M, Hannard F, Ding L, Zhao L, Maire E, Villanova J, Idrissi H, Simar A, Acta materialia 238, 118241 (2022). http://doi.org/10.1016/J.ACTAMAT.2022.118241
Abstract: Self-healing strategies aim at avoiding part repair or even replacement, which is time consuming, expen-sive and generates waste. However, strategies for metallic systems are still under-developed and solid-state solutions for room temperature service are limited to nano-scale damage repair. Here we propose a new healing strategy of micron-sized damage requiring only short and low temperature heating. This new strategy is based on damage localization particles, which can be healed by fast diffusing atoms of the matrix activated during heat treatment. The healing concept was successfully validated with a com-mercial aluminum alloy and manufactured by Friction Stir Processing (FSP). Damage was demonstrated to initiate on particles that were added to the matrix during material processing. In situ 2D and 3D nano -imaging confirmed healing of the damaged material and showed that heating this material for 10 min at 400 degrees C is sufficient to heal incipient damage with complete filling of 70% of all damage (and up to 90% when their initial size is below 0.2 mu m). Furthermore, strength is retained and the work of fracture of the alloy is improved by about 40% after healing. The proposed Programmed Damage and Repair healing strategy could be extended to other metal based systems presenting precipitation. (C) 2022 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.
Keywords: A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
Impact Factor: 9.4
DOI: 10.1016/J.ACTAMAT.2022.118241
|
“A new generalized empirical correlation for predicting methane hydrate equilibrium conditions in pure water”. Kummamuru NB, Perreault P, Lenaerts S, Industrial &, Engineering Chemistry Research 60, 3474 (2021). http://doi.org/10.1021/ACS.IECR.0C05833
Abstract: This work contributes to a new generalized empirical correlation for predicting methane (CH4) hydrate equilibrium conditions in pure water. Unlike the conventional thermodynamic approach that involves complex reckoning, the proposed empirical equation is developed by regressing 215 experimental data points from the literature and validating with 45 data points for predicting methane hydrate equilibrium conditions in pure water. The new correlation is proposed for a temperature and pressure range of 273.2–303.48 K and 2.63–72.26 MPa, respectively. The accuracy and performance of the proposed correlation is quantitatively evaluated using statistical error analysis. The proposed correlation was able to estimate CH4 hydrate equilibrium conditions satisfactorily with an R2 of 0.99987. The overall error analysis for the proposed correlation shows fair agreement with the experimental data reported within the literature. Concurrently, the new correlation showed better performance in predicting equilibrium conditions compared to those calculated by other empirical correlations available in the literature within the investigated range. In addition, the proposed empirical equation is also checked to evaluate its efficacy in fitting each set of experimental binary/ternary methane hydrates (BTMH) and binary hydrogen hydrates (BHH) for an accurate representation of equilibrium data over a wide range of composition, pressure, and temperature conditions. A maximum percentage deviation of 0.58% and 0.24% was observed between experimental and calculated equilibrium conditions for BTMH and BHH, respectively.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 2.843
DOI: 10.1021/ACS.IECR.0C05833
|
“A new approach to circular inversion in l₁-normed spaces”. Ermiş, T, Şen AO, Gielis J, Symmetry 16, 874 (2024). http://doi.org/10.3390/SYM16070874
Abstract: While there are well-known synthetic methods in the literature for finding the image of a point under circular inversion in l2-normed geometry (Euclidean geometry), there is no similar synthetic method in Minkowski geometry, also known as the geometry of finite-dimensional Banach spaces. In this study, we have succeeded in creating a synthetic construction of the circular inversion in l1-normed spaces, which is one of the most fundamental examples of Minkowski geometry. Moreover, this synthetic construction has been given using the Euclidean circle, independently of the l1-norm.
Keywords: A1 Journal article; Engineering sciences. Technology; Antwerp engineering, PhotoElectroChemistry & Sensing (A-PECS)
Impact Factor: 2.7
DOI: 10.3390/SYM16070874
|
“A multisensor hyperspectral benchmark dataset for unmixing of intimate mixtures”. Koirala B, Rasti B, Bnoulkacem Z, de Lima Ribeiro A, Madriz Y, Herrmann E, Gestels A, De Kerf T, Lorenz S, Fuchs M, Janssens K, Steenackers G, Gloaguen R, Scheunders P, IEEE sensors journal 24, 4694 (2024). http://doi.org/10.1109/JSEN.2023.3343552
Abstract: Optical hyperspectral cameras capture the spectral reflectance of materials. Since many materials behave as heterogeneous intimate mixtures with which each photon interacts differently, the relationship between spectral reflectance and material composition is very complex. Quantitative validation of spectral unmixing algorithms requires high-quality ground truth fractional abundance data, which are very difficult to obtain. In this work, we generated a comprehensive laboratory ground truth dataset of intimately mixed mineral powders. For this, five clay powders (Kaolin, Roof clay, Red clay, mixed clay, and Calcium hydroxide) were mixed homogeneously to prepare 325 samples of 60 binary, 150 ternary, 100 quaternary, and 15 quinary mixtures. Thirteen different hyperspectral sensors have been used to acquire the reflectance spectra of these mixtures in the visible, near, short, mid, and long-wavelength infrared regions (350-15385) nm. Overlaps in wavelength regions due to the operational ranges of each sensor and variations in acquisition conditions resulted in a large amount of spectral variability. Ground truth composition is given by construction, but to verify that the generated samples are sufficiently homogeneous, XRD and XRF elemental analysis is performed. We believe these data will be beneficial for validating advanced methods for nonlinear unmixing and material composition estimation, including studying spectral variability and training supervised unmixing approaches. The datasets can be downloaded from the following link: https://github.com/VisionlabHyperspectral/Multisensor_datasets.
Keywords: A1 Journal article; Engineering sciences. Technology; Vision lab; Antwerp X-ray Imaging and Spectroscopy (AXIS)
Impact Factor: 4.3
DOI: 10.1109/JSEN.2023.3343552
|
“A multidimensional indicator set to assess the benefits of WEEE material recycling”. Nelen D, Manshoven S, Peeters JR, Vanegas P, D'Haese N, Vrancken K, Journal of cleaner production 83, 305 (2014). http://doi.org/10.1016/J.JCLEPRO.2014.06.094
Abstract: EU strategies for waste management have long recognized the key role of recycling to move towards sustainable consumption and production. This resulted in a range of regulatory measures, among which the Waste Electrical and Electronic Equipment (WEEE) directive, which sets weight-based targets for recovery, preparation for re-use and recycling. The increasing strategic relevance of the supply of raw materials has, however, spurred a more integrated approach towards resource efficiency. In addition to the prevention of disposal, recycling practices are now also meant to contribute to sustainable materials management by pursuing (i) a higher degree of material cycle closure, (ii) an improved recovery of strategically relevant materials, and (iii) the avoidance of environmental burdens associated with the extraction and refining of primary raw materials. In response to this evolution, this paper reports about the development of an indicator set that allows to quantitatively demonstrate these recycling benefits, hence going further than the weight-based objectives employed in the WEEE directive. The indicators can be calculated for WEEE recycling processes for which information is available on both input and output fractions. It offers a comprehensive framework that aims to support decision making processes on product design, to identify opportunities for the optimization of WEEE End-of-Life scenarios, and to assess the achieved (or expected) results of implemented (or planned) recycling optimization strategies. The paper is illustrated by a case study on the recycling of LCD televisions. (C) 2014 Elsevier Ltd. All rights reserved.
Keywords: A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1016/J.JCLEPRO.2014.06.094
|
“A Monte Carlo program for quantitative electron-induced x-ray analysis of individual particles”. Ro C-U, Osán J, Szalóki I, de Hoog J, Worobiec A, Van Grieken R, Analytical chemistry 75, 851 (2003). http://doi.org/10.1021/AC025973R
Keywords: A1 Journal article; Laboratory Experimental Medicine and Pediatrics (LEMP); AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation)
DOI: 10.1021/AC025973R
|
“A mobile scanner for xrpd-imaging of paintings in transmission and reflection geometry”. De Meyer S, Vanmeert F, Janssens K, Storme P, ACTA ARTIS ACADEMICA 2017: PAINTING AS A STORY
T2 –, 6th Interdisciplinary ALMA Conference, JUN 01-03, 2017, Brno, CZECH REPUBLIC , 29 (2017)
Abstract: In this paper the possibilities and limitations of a non-invasive prototype of macroscopic X-ray powder diffraction scanning device employed in transmission and reflection mode are demonstrated. Contrarily to e.g. macroscopic X-ray fluorescence scanners, which gather information on the elemental level, the prototype instrument allows to obtain information on the crystallographic structure of the components. When applied to cultural heritage artefacts, it becomes possible to identify and localize crystalline pigments. Furthermore, it became clear that different information can be available depending on the geometry of the scanner components. In transmission mode information over the entire stratigraphy of the painting is gathered, which is useful to e.g. identify background substrates and major pigments. On the other hand, reflection-XRPD is a surface-sensitive technique and allows the identification of pigments and degradation products located on the surface. The data acquired during both experiments can be presented as two-dimensional distribution maps which show the spatial distribution of every identified pigment. The complementary nature of transmission and reflectionmode makes it possible to gain more insight into the stratigraphy of the painting which is valuable information for conservation and restoration scientists.
Keywords: P1 Proceeding; Art; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation); Antwerp Cultural Heritage Sciences (ARCHES)
|
“A microanalytical study of the gills of aluminium-exposed rainbow trout (Salmo gairdneri)”. Goossenaerts C, Van Grieken R, Jacob W, Witters H, Vanderborght O, International journal of environmental analytical chemistry 34, 227 (1988). http://doi.org/10.1080/03067319808026840
Keywords: A1 Journal article; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation)
DOI: 10.1080/03067319808026840
|
“A microanalytical study of the gills of aluminium-exposed catfish”. Eeckhaoudt S, Landsberg J, Van Grieken R, Jacob W, Watt F, Witters H, Institute of physics conference series
T2 –, Proceedings of the 13th International Congress on X-Ray Optics and Microanalysis / Kenway, P.B. [edit.] , 251 (1993)
Abstract: Through a combined use of light- and electron microscopy with microanalytical techniques, the aluminium distribution in gills of aluminium-exposed catfish was investigated. This study demonstrates that also with the ''acid-resistant'' catfish, exposed during seven days to acidified water (pH=4.3) with an elevated aluminium concentration (1 mg Al/l), aluminium can be found at, and even in, the gills.
Keywords: P1 Proceeding; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation)
|