“Precision magnetometry on a submicron scale: magnetisation of superconducting quantum dots”. Geim AK, Grigorieva IV, Lok JGS, Maan JC, Dubonos SV, Li XQ, Peeters FM, Nazarov YV, Superlattices and microstructures 23, 151 (1998). http://doi.org/10.1006/spmi.1996.0199
Abstract: We report on magnetisation of individual superconducting particles with size down to 0.1 micron. The non-invasive access to properties of such small objects has become possible using submicron Hall probes which detect a local magnetic field and work effectively as micro-fluxmeters similar to, e.g., SQUIDs but with an effective detection loop of only about a square micron. We have found that the spatial confinement of superconductivity in a small volume gives rise to dramatic changes in thermodynamic properties of mesoscopic superconductors. (C) 1998 Academic Press Limited.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 2.123
Times cited: 12
DOI: 10.1006/spmi.1996.0199
|
“Predicted field-dependent increase of critical currents in asymmetric superconducting nanocircuits”. Clem JR, Mawatari Y, Berdiyorov GR, Peeters FM, Physical review : B : condensed matter and materials physics 85, 144511 (2012). http://doi.org/10.1103/PhysRevB.85.144511
Abstract: The critical current of a thin superconducting strip of width W much larger than the Ginzburg-Landau coherence length xi but much smaller than the Pearl length Lambda = 2 lambda(2)/d is maximized when the strip is straight with defect-free edges. When a perpendicular magnetic field is applied to a long straight strip, the critical current initially decreases linearly with H but then decreases more slowly with H when vortices or antivortices are forced into the strip. However, in a superconducting strip containing sharp 90 degrees or 180 degrees turns, the zero-field critical current at H = 0 is reduced because vortices or antivortices are preferentially nucleated at the inner corners of the turns, where current crowding occurs. Using both analytic London-model calculations and time-dependent Ginzburg-Landau simulations, we predict that in such asymmetric strips the resulting critical current can be increased by applying a perpendicular magnetic field that induces a current-density contribution opposing the applied current density at the inner corners. This effect should apply to all turns that bend in the same direction.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 3.836
Times cited: 40
DOI: 10.1103/PhysRevB.85.144511
|
“Prediction of hyperbolic exciton-polaritons in monolayer black phosphorus”. Wang F, Wang C, Chaves A, Song C, Zhang G, Huang S, Lei Y, Xing Q, Mu L, Xie Y, Yan H, Nature Communications 12, 5628 (2021). http://doi.org/10.1038/S41467-021-25941-5
Abstract: Hyperbolic polaritons exhibit large photonic density of states and can be collimated in certain propagation directions. The majority of hyperbolic polaritons are sustained in man-made metamaterials. However, natural-occurring hyperbolic materials also exist. Particularly, natural in-plane hyperbolic polaritons in layered materials have been demonstrated in MoO3 and WTe2, which are based on phonon and plasmon resonances respectively. Here, by determining the anisotropic optical conductivity (dielectric function) through optical spectroscopy, we predict that monolayer black phosphorus naturally hosts hyperbolic exciton-polaritons due to the pronounced in-plane anisotropy and strong exciton resonances. We simultaneously observe a strong and sharp ground state exciton peak and weaker excited states in high quality monolayer samples in the reflection spectrum, which enables us to determine the exciton binding energy of similar to 452 meV. Our work provides another appealing platform for the in-plane natural hyperbolic polaritons, which is based on excitons rather than phonons or plasmons.
Keywords: A1 Journal article; Engineering sciences. Technology; Condensed Matter Theory (CMT)
Impact Factor: 12.124
DOI: 10.1038/S41467-021-25941-5
|
“Prediction of monoclinic single-layer Janus Ga₂, Te X (X = S and Se) : strong in-plane anisotropy”. Yagmurcukardes M, Mogulkoc Y, Akgenc B, Mogulkoc A, Peeters FM, Physical Review B 104, 045425 (2021). http://doi.org/10.1103/PHYSREVB.104.045425
Abstract: By using density functional theory (DFT) based first-principles calculations, electronic, vibrational, piezo-electric, and optical properties of monoclinic Janus single-layer Ga2TeX (X = S or Se) are investigated. The dynamical, mechanical, and thermal stability of the proposed Janus single layers are verified by means of phonon bands, stiffness tensor, and quantum molecular dynamics simulations. The calculated vibrational spectrum reveals the either pure or coupled optical phonon branches arising from Ga-Te and Ga-X atoms. In addition to the in-plane anisotropy, single-layer Janus Ga2TeX exhibits additional out-of-plane asymmetry, which leads to important consequences for its electronic and optical properties. Electronic band dispersions indicate the direct band-gap semiconducting nature of the constructed Janus structures with energy band gaps falling into visible spectrum. Moreover, while orientation-dependent linear-elastic properties of Janus single layers indicate their strong anisotropy, the calculated in-plane stiffness values reveal the ultrasoft nature of the structures. In addition, predicted piezoelectric coefficients show that while there is a strong in-plane anisotropy between piezoelectric constants along armchair (AC) and zigzag (ZZ) directions, there exists a tiny polarization along the out-of-plane direction as a result of the formation of Janus structure. The optical response to electromagnetic radiation has been also analyzed through density functional theory by considering the independent-particle approximation. Finally, the optical spectra of Janus Ga2TeX structures is investigated and it showed a shift from the ultraviolet region to the visible region. The fact that the spectrum is between these regions will allow it to be used in solar energy and many nanoelectronics applications. The predicted monoclinic single-layer Janus Ga2TeX are relevant for promising applications in optoelectronics, optical dichroism, and anisotropic nanoelasticity.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 3.836
Times cited: 14
DOI: 10.1103/PHYSREVB.104.045425
|
“Prediction of novel two-dimensional Dirac nodal line semimetals in Al₂B₂, and AlB₄, monolayers”. Abedi S, Sisakht ET, Hashemifar SJ, Cherati NG, Sarsari IA, Peeters FM, Nanoscale 14, 11270 (2022). http://doi.org/10.1039/D2NR00888B
Abstract: Topological semimetal phases in two-dimensional (2D) materials have gained widespread interest due to their potential applications in novel nanoscale devices. Despite the growing number of studies on 2D topological nodal lines (NLs), candidates with significant topological features that combine nontrivial topological semimetal phase with superconductivity are still rare. Herein, we predict Al2B2 and AlB4 monolayers as new 2D nonmagnetic Dirac nodal line semimetals with several novel features. Our extensive electronic structure calculations combined with analytical studies reveal that, in addition to multiple Dirac points, these 2D configurations host various highly dispersed NLs around the Fermi level, all of which are semimetal states protected by time-reversal and in-plane mirror symmetries. The most intriguing NL in Al2B2 encloses the K point and crosses the Fermi level, showing a considerable dispersion and thus providing a fresh playground to explore exotic properties in dispersive Dirac nodal lines. More strikingly, for the AlB4 monolayer, we provide the first evidence for a set of 2D nonmagnetic open type-II NLs coexisting with superconductivity at a rather high transition temperature. The coexistence of superconductivity and nontrivial band topology in AlB4 not only makes it a promising material to exhibit novel topological superconducting phases, but also a rather large energy dispersion of type-II nodal lines in this configuration may offer a platform for the realization of novel topological features in the 2D limit.
Keywords: A1 Journal article; Engineering sciences. Technology; Condensed Matter Theory (CMT)
Impact Factor: 6.7
Times cited: 5
DOI: 10.1039/D2NR00888B
|
“Prediction of two-dimensional bismuth-based chalcogenides Bi₂X₃(X = S, Se, Te) monolayers with orthorhombic structure : a first-principles study”. Bafekry A, Faraji M, Fadlallah MM, Jappor HR, Hieu NN, Ghergherehchi M, Feghhi SAH, Gogova D, Journal Of Physics D-Applied Physics 54, 395103 (2021). http://doi.org/10.1088/1361-6463/AC118C
Abstract: First-principles calculation is a very powerful tool for discovery and design of novel two-dimensional materials with unique properties needed for the next generation technology. Motivated by the successful preparation of Bi2S3 nanosheets with orthorhombic structure in the last year, herein we gain a deep theoretical insight into the crystal structure, stability, electronic and optical properties of Bi2X3 (X = S, Se, Te) monolayers of orthorhombic phase employing the first-principles calculations. The Molecular dynamics study, phonon spectra, criteria for elastic stability, and cohesive energy results confirm the desired stability of the Bi2X3 monolayers. From S, to Se and Te, the work function value as well as stability of the systems decrease due to the decline in electronegativity. Mechanical properties study reveals that Bi2X3 monolayers have brittle nature. The electronic bandgap values of Bi2S3, Bi2Se3 and Bi2Te3 monolayers are predicted by the HSE06 functional to be 2.05, 1.20 and 1.16 eV, respectively. By assessing the optical properties, it has been found that Bi2X3 monolayers can absorb ultraviolet light. The high in-plane optical anisotropy offers an additional degree of freedom in the design of optical devices. The properties revealed in our survey will stimulate and inspire the search for new approaches of orthorhombic Bi2X3 (X = S, Se, Te) monolayers synthesis and properties manipulation for fabrication of novel nanoelectronic and optoelectronic devices.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 2.588
DOI: 10.1088/1361-6463/AC118C
|
“Preface”. Aguiar JA, Roa-Rojas J, Parra Vargas CA, Landinez Tellez DA, Corredor Bohorquez LT, Shanenko A, Jardim RF, Peeters F, Physica: B : condensed matter 455, 1 (2014). http://doi.org/10.1016/j.physb.2014.05.013
Keywords: Editorial; Condensed Matter Theory (CMT)
Impact Factor: 1.386
DOI: 10.1016/j.physb.2014.05.013
|
“Prevalence of oxygen defects in an in-plane anisotropic transition metal dichalcogenide”. Plumadore R, Baskurt M, Boddison-Chouinard J, Lopinski G, Modarresi M, Potasz P, Hawrylak P, Sahin H, Peeters FM, Luican-Mayer A, Physical Review B 102, 205408 (2020). http://doi.org/10.1103/PHYSREVB.102.205408
Abstract: Atomic scale defects in semiconductors enable their technological applications and realization of different quantum states. Using scanning tunneling microscopy and spectroscopy complemented by ab initio calculations we determine the nature of defects in the anisotropic van der Waals layered semiconductor ReS2. We demonstrate the in-plane anisotropy of the lattice by directly visualizing chains of rhenium atoms forming diamond-shaped clusters. Using scanning tunneling spectroscopy we measure the semiconducting gap in the density of states. We reveal the presence of lattice defects and by comparison of their topographic and spectroscopic signatures with ab initio calculations we determine their origin as oxygen atoms absorbed at lattice point defect sites. These results provide an atomic-scale view into the semiconducting transition metal dichalcogenides, paving the way toward understanding and engineering their properties.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 3.7
Times cited: 9
DOI: 10.1103/PHYSREVB.102.205408
|
“Probing charge density wave phases and the Mott transition in 1T-TaS₂I by inelastic light scattering”. Mijin SD, Baum A, Bekaert J, Solajic A, Pesic J, Liu Y, He G, Milošević, MV, Petrovic C, Popovic Z V, Hackl R, Lazarevic N, Physical Review B 103, 245133 (2021). http://doi.org/10.1103/PHYSREVB.103.245133
Abstract: We present a polarization-resolved, high-resolution Raman scattering study of the three consecutive charge density wave (CDW) regimes in 1T-TaS2 single crystals, supported by ab initio calculations. Our analysis of the spectra within the low-temperature commensurate (C-CDW) regime shows P (3) over bar symmetry of the system, thus excluding the previously proposed triclinic stacking of the “star-of-David” structure, and promoting trigonal or hexagonal stacking instead. The spectra of the high-temperature incommensurate (IC-CDW) phase directly project the phonon density of states due to the breaking of the translational invariance, supplemented by sizable electron-phonon coupling. Between 200 and 352 K, our Raman spectra show contributions from both the IC-CDW and the C-CDW phases, indicating their coexistence in the so-called nearly commensurate (NC-CDW) phase. The temperature dependence of the symmetry-resolved Raman conductivity indicates the stepwise reduction of the density of states in the CDW phases, followed by a Mott transition within the C-CDW phase. We determine the size of the Mott gap to be Omega(gap) approximate to 170-190 meV, and track its temperature dependence.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 3.836
Times cited: 4
DOI: 10.1103/PHYSREVB.103.245133
|
“Probing confined vortices with a superconducting nanobridge”. Foltyn M, Norowski K, Wyszynski MJ, De Arruda AS, Milošević, MV, Zgirski M, Physical review applied 19, 044073 (2023). http://doi.org/10.1103/PHYSREVAPPLIED.19.044073
Abstract: We realize a superconducting nanodevice in which vortex traps in the form of an aluminum square are integrated with a Dayem nanobridge. We perform field cooling of the traps arriving to different vortex configurations, dependent on the applied magnetic field, to demonstrate that the switching current of the bridge is highly sensitive to the presence and location of vortices in the trap. Our measurements exhibit unprecedented precision and ability to detect the first and successive vortex entries into all fabricated traps, from few hundred nm to 2 mu m in size. The experimental results are corroborated by Ginzburg-Landau simulations, which reveal the subtle yet crucial changes in the density of the superconducting condensate in the vicinity of the bridge with every additional vortex entry and relocation inside the trap. An ease of integration and simplicity make our design a convenient platform for studying dynamics of vortices in strongly confining geometries, involving a promise to manipulate vortex states electronically with simultaneous in situ control and monitoring.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 4.6
DOI: 10.1103/PHYSREVAPPLIED.19.044073
|
“Probing of the electron-phonon interaction using high magnetic fields”. Peeters FM, Physicalia magazine 19, 187 (1997)
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
|
“Probing the dynamic response of antivortex, interstitial and trapped vortex lattices on magnetic periodic pinning potentials”. Gomez A, Gonzalez EM, Gilbert DA, Milošević, MV, Liu K, Vicent JL, Superconductor science and technology 26, 085018 (2013). http://doi.org/10.1088/0953-2048/26/8/085018
Abstract: The dynamics of the pinned vortex, antivortex and interstitial vortex have been studied in superconducting/magnetic hybrids consisting of arrays of Co/Pd multilayer nanodots embedded in Nb films. The magnetic nanodots show out-of-plane magnetization at the remanent state. This magnetic state allows for superconducting vortex lattices of different types in an applied homogeneous magnetic field. We experimentally and theoretically show three such lattices: (i) a lattice containing only antivortices; (ii) a vortex lattice entirely pinned on the dots; and (iii) a vortex lattice with pinned and interstitial vortices. Between the flux creep (low vortex velocity) and the free flux flow (high vortex velocity) regimes the interaction between the magnetic array and the vortex lattice governs the vortex dynamics, which in turn enables distinguishing experimentally the type of vortex lattice which governs the dissipation. We show that the vortex lattice with interstitial vortices has the highest onset velocity where the lattice becomes ordered, whereas the pinned vortex lattice has the smallest onset velocity. Further, for this system, we directly estimate that the external force needed to depin vortices is 60% larger than the one needed to depin antivortices; therefore we are able to decouple the antivortex-vortex motion.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 2.878
Times cited: 7
DOI: 10.1088/0953-2048/26/8/085018
|
“Probing the intrinsic limitations of the contact resistance of metal/semiconductor interfaces through atomistic simulations”. Pourtois G, Dabral A, Sankaran K, Magnus W, Yu H, de de Meux AJ, Lu AKA, Clima S, Stokbro K, Schaekers M, Houssa M, Collaert N, Horiguchi N, Semiconductors, Dielectrics, And Metals For Nanoelectronics 15: In Memory Of Samares Kar , 303 (2017). http://doi.org/10.1149/08001.0303ECST
Abstract: In this contribution, we report a fundamental study of the factors that set the contact resistivity between metals and highly doped semiconductors. We investigate the case of n-type doped Si contacted with amorphous TiSi combining first-principles calculations with Non-Equilibrium Green functions transport simulations. The intrinsic contact resistivity is found to saturate at similar to 2x10(-10) Omega.cm(2) with the doping concentration and sets an intrinsic limit to the ultimate contact resistance achievable for n-doped Si vertical bar amorphous-TiSi. This limit arises from the intrinsic properties of the semiconductor and of the metal such as their electron effective masses and Fermi energies. We illustrate that, in this regime, contacting metals with a heavy electron effective mass helps reducing the interface intrinsic contact resistivity.
Keywords: P1 Proceeding; Engineering sciences. Technology; Condensed Matter Theory (CMT); Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Times cited: 1
DOI: 10.1149/08001.0303ECST
|
“Probing the structure and composition of van der Waals heterostructures using the nonlocality of Dirac plasmons in the terahertz regime”. Lavor IR, Cavalcante LSR, Chaves A, Peeters FM, Van Duppen B, 2d Materials 8, 015014 (2021). http://doi.org/10.1088/2053-1583/ABBECC
Abstract: Dirac plasmons in graphene are very sensitive to the dielectric properties of the environment. We show that this can be used to probe the structure and composition of van der Waals heterostructures (vdWh) put underneath a single graphene layer. In order to do so, we assess vdWh composed of hexagonal boron nitride and different types of transition metal dichalcogenides (TMDs). By performing realistic simulations that account for the contribution of each layer of the vdWh separately and including the importance of the substrate phonons, we show that one can achieve single-layer resolution by investigating the nonlocal nature of the Dirac plasmon-polaritons. The composition of the vdWh stack can be inferred from the plasmon-phonon coupling once it is composed by more than two TMD layers. Furthermore, we show that the bulk character of TMD stacks for plasmonic screening properties in the terahertz regime is reached only beyond 100 layers.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 6.937
Times cited: 4
DOI: 10.1088/2053-1583/ABBECC
|
“Process variability in Cu2ZnSnSe4 solar cell devices: Electrical and structural investigations”. Brammertz G, Buffiere M, Verbist C, Bekaert J, Batuk M, Hadermann J, et al, The conference record of the IEEE Photovoltaic Specialists Conference
T2 –, IEEE 42nd Photovoltaic Specialist Conference (PVSC), JUN 14-19, 2015, New Orleans, LA (2015)
Abstract: We have fabricated 9.7% efficient Cu2ZnSnSe4/CdS/ZnO solar cells by H2Se selenization of sequentially sputtered metal layers. Despite the good efficiency obtained, process control appears to be difficult. In the present contribution we compare the electrical and physical properties of two devices with nominal same fabrication procedure, but 1% and 9.7% power conversion efficiency respectively. We identify the problem of the lower performing device to be the segregation of ZnSe phases at the backside of the sample. This ZnSe seems to be the reason for the strong bias dependent photocurrent observed in the lower performing devices, as it adds a potential barrier for carrier collection. The reason for the different behavior of the two nominally same devices is not fully understood, but speculated to be related to sputtering variability.
Keywords: P1 Proceeding; Engineering sciences. Technology; Electron microscopy for materials research (EMAT); Condensed Matter Theory (CMT)
|
“Progressive melting in confined one-dimensional C60 chains”. Bousige C, Rols S, Paineau E, Rouziere S, Mocuta C, Verberck B, Wright JP, Kataura H, Launois P, Physical review : B : condensed matter and materials physics 86, 045446 (2012). http://doi.org/10.1103/PhysRevB.86.045446
Abstract: C-60 fullerenes confined inside single-walled carbon nanotubes form an archetypal one-dimensional system. X-ray diffraction experiments, from room temperature to 1073 K, reveal an increasing melting phenomenon. Detailed analysis of the sawtooth peak characteristic of the fullerene organization allows the quantitative determination of fluctuations in intermolecular distances. The present results validate the predictions of one-dimensional statistical models.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 3.836
DOI: 10.1103/PhysRevB.86.045446
|
“Promising Piezoelectric Performance of Single Layer Transition-Metal Dichalcogenides and Dioxides”. Alyörük MM, Aierken Y, Çakır D, Peeters FM, Sevik C, The journal of physical chemistry: C : nanomaterials and interfaces 119, 23231 (2015). http://doi.org/10.1021/acs.jpcc.5b06428
Abstract: Piezoelectricity is a unique material property that allows one to convert mechanical energy into electrical one or vice versa. Transition metal dichalcogenides (TMDC) and transition metal dioxides (TMDO) are expected to have great potential for piezoelectric device applications due to their noncentrosymmetric and two-dimensional crystal structure. A detailed theoretical investigation of the piezoelectric stress (e 11 ) and piezoelectric strain (d 11 ) coefficients of single layer TMDCs and TMDOs with chemical formula MX 2 (where M= Cr, Mo, W, Ti, Zr, Hf, Sn and X = O, S, Se, Te) is presented by using first-principles calculations based on density func- tional theory. We predict that not only the Mo- and W-based members of this family but also the other materials with M= Cr, Ti, Zr and Sn exhibit highly promising piezoelectric properties. CrTe 2 has the largest e 11 and d 11 coefficients among the group VI elements (i.e., Cr, Mo, and W). In addition, the relaxed-ion e 11 and d 11 coefficients of SnS 2 are almost the same as those of CrTe 2 . Furthermore, TiO 2 and ZrO 2 pose comparable or even larger e 11 coefficients as compared to Mo- and W-based TMDCs and TMDOs. Our calculations reveal that TMDC and TMDO structures are strong candidates for future atomically thin piezoelectric applications such as transducers, sensors, and energy harvesting devices due to their piezoelectric coefficients that are comparable (even larger) to currently used bulk piezoelectric materials.
Keywords: A1 Journal article; Engineering sciences. Technology; Condensed Matter Theory (CMT)
Impact Factor: 4.536
Times cited: 134
DOI: 10.1021/acs.jpcc.5b06428
|
“Promising room temperature thermoelectric conversion efficiency of zinc-blende AgI from first principles”. Bulut P, Beceren B, Yildirim S, Sevik C, Gurel T, Journal Of Physics-Condensed Matter 33, 015501 (2021). http://doi.org/10.1088/1361-648X/ABB867
Abstract: The theoretical investigation on structural, vibrational, and electronic properties of zinc-blende (ZB) AgI were carried out employing first principles density functional theory calculations. Thermoelectric properties then were predicted through semi-classical Boltzmann transport equations within the constant relaxation time approximation. Equilibrium lattice parameter, bulk modulus, elastic constants, and vibrational properties were calculated by using generalized gradient approximation. Calculated properties are in good agreement with available experimental values. Electronic and thermoelectric properties were investigated both with and without considering spin-orbit coupling (SOC) effect which is found to have a strong influence on p-type Seebeck coefficient as well as the power factor of the ZB-AgI. By inclusion of SOC, a reduction of the band-gap and p-type Seebeck coefficients as well as the power factor was found which is the indication of that spin-orbit interaction cannot be ignored for p-type thermoelectric properties of the ZB-AgI. By using deformation potential theory for electronic relaxation time and experimentally predicted lattice thermal conductivity, we obtained aZTvalue 1.69 (0.89) at 400 K for n-type (p-type) carrier concentration of 1.5 x 10(18)(4.6 x10(19)) cm(-3)that makes ZB-AgI as a promising room temperature thermoelectric material.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 2.649
DOI: 10.1088/1361-648X/ABB867
|
“Properties of B and P doped Ge nanowires”. Peelaers H, Partoens B, Peeters FM, Applied physics letters 90, 263103 (2007). http://doi.org/10.1063/1.2752107
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 3.411
Times cited: 35
DOI: 10.1063/1.2752107
|
Vieira De Castro L (2019) Properties of quasi particles on two dimensional materials and related structures. 79 p
Keywords: Doctoral thesis; Condensed Matter Theory (CMT)
|
“Properties of two-dimensional Coulomb clusters confined in a ring”. Schweigert IV, Schweigert VA, Peeters FM, Physical review : B : condensed matter and materials physics 54, 10827 (1996). http://doi.org/10.1103/PhysRevB.54.10827
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 3.736
Times cited: 27
DOI: 10.1103/PhysRevB.54.10827
|
“Proposal for nanoscale cascaded plasmonic majority gates for non-Boolean computation”. Dutta S, Zografos O, Gurunarayanan S, Radu I, Sorée B, Catthoor F, Naeemi A, Scientific reports 7, 17866 (2017). http://doi.org/10.1038/S41598-017-17954-2
Abstract: <script type='text/javascript'>document.write(unpmarked('Surface-plasmon-polariton waves propagating at the interface between a metal and a dielectric, hold the key to future high-bandwidth, dense on-chip integrated logic circuits overcoming the diffraction limitation of photonics. While recent advances in plasmonic logic have witnessed the demonstration of basic and universal logic gates, these CMOS oriented digital logic gates cannot fully utilize the expressive power of this novel technology. Here, we aim at unraveling the true potential of plasmonics by exploiting an enhanced native functionality – the majority voter. Contrary to the state-of-the-art plasmonic logic devices, we use the phase of the wave instead of the intensity as the state or computational variable. We propose and demonstrate, via numerical simulations, a comprehensive scheme for building a nanoscale cascadable plasmonic majority logic gate along with a novel referencing scheme that can directly translate the information encoded in the amplitude and phase of the wave into electric field intensity at the output. Our MIM-based 3-input majority gate displays a highly improved overall area of only 0.636 mu m(2) for a single-stage compared with previous works on plasmonic logic. The proposed device demonstrates non-Boolean computational capability and can find direct utility in highly parallel real-time signal processing applications like pattern recognition.'));
Keywords: A1 Journal article; Engineering sciences. Technology; Condensed Matter Theory (CMT)
Impact Factor: 4.259
Times cited: 2
DOI: 10.1038/S41598-017-17954-2
|
“Proton and Li-Ion permeation through graphene with eight-atom-ring defects”. Griffin E, Mogg L, Hao G-P, Kalon G, Bacaksiz C, Lopez-Polin G, Zhou TY, Guarochico V, Cai J, Neumann C, Winter A, Mohn M, Lee JH, Lin J, Kaiser U, Grigorieva I V, Suenaga K, Ozyilmaz B, Cheng H-M, Ren W, Turchanin A, Peeters FM, Geim AK, Lozada-Hidalgo M, Acs Nano 14, 7280 (2020). http://doi.org/10.1021/ACSNANO.0C02496
Abstract: Defect-free graphene is impermeable to gases and liquids but highly permeable to thermal protons. Atomic-scale defects such as vacancies, grain boundaries, and Stone-Wales defects are predicted to enhance graphene's proton permeability and may even allow small ions through, whereas larger species such as gas molecules should remain blocked. These expectations have so far remained untested in experiment. Here, we show that atomically thin carbon films with a high density of atomic-scale defects continue blocking all molecular transport, but their proton permeability becomes similar to 1000 times higher than that of defect-free graphene. Lithium ions can also permeate through such disordered graphene. The enhanced proton and ion permeability is attributed to a high density of eight-carbon-atom rings. The latter pose approximately twice lower energy barriers for incoming protons compared to that of the six-atom rings of graphene and a relatively low barrier of similar to 0.6 eV for Li ions. Our findings suggest that disordered graphene could be of interest as membranes and protective barriers in various Li-ion and hydrogen technologies.
Keywords: A1 Journal article; Engineering sciences. Technology; Condensed Matter Theory (CMT)
Impact Factor: 17.1
Times cited: 53
DOI: 10.1021/ACSNANO.0C02496
|
“Proton transport through nanoscale corrugations in two-dimensional crystals”. Wahab OJ, Daviddi E, Xin B, Sun PZ, Griffin E, Colburn AW, Barry D, Yagmurcukardes M, Peeters FM, Geim AK, Lozada-Hidalgo M, Unwin PR, Nature 620, 1 (2023). http://doi.org/10.1038/S41586-023-06247-6
Abstract: Defect-free graphene is impermeable to all atoms(1-5) and ions(6,7) under ambient conditions. Experiments that can resolve gas flows of a few atoms per hour through micrometre-sized membranes found that monocrystalline graphene is completely impermeable to helium, the smallest atom(2,5). Such membranes were also shown to be impermeable to all ions, including the smallest one, lithium(6,7). By contrast, graphene was reported to be highly permeable to protons, nuclei of hydrogen atoms(8,9). There is no consensus, however, either on the mechanism behind the unexpectedly high proton permeability(10-14) or even on whether it requires defects in graphene's crystal lattice(6,8,15-17). Here, using high-resolution scanning electrochemical cell microscopy, we show that, although proton permeation through mechanically exfoliated monolayers of graphene and hexagonal boron nitride cannot be attributed to any structural defects, nanoscale non-flatness of two-dimensional membranes greatly facilitates proton transport. The spatial distribution of proton currents visualized by scanning electrochemical cell microscopy reveals marked inhomogeneities that are strongly correlated with nanoscale wrinkles and other features where strain is accumulated. Our results highlight nanoscale morphology as an important parameter enabling proton transport through two-dimensional crystals, mostly considered and modelled as flat, and indicate that strain and curvature can be used as additional degrees of freedom to control the proton permeability of two-dimensional materials. A study using high-resolution scanning electrochemical cell microscopy attributes proton permeation through defect-free graphene and hexagonal boron nitride to transport across areas of the structure that are under strain.
Keywords: A1 Journal article; Engineering sciences. Technology; Condensed Matter Theory (CMT)
Impact Factor: 64.8
Times cited: 17
DOI: 10.1038/S41586-023-06247-6
|
“Proton tunneling and nonlinear polarizability effects in hydrogen-bonded ferroelectrics”. Bussmann-Holder A, Michel KH, AIP conference proceedings
T2 –, 5th Williamsburg Workshop on 1st-Principles Calculations for, Ferroelectrics, FEB 01-04, 1998, WILLIAMSBURG, VA , 202 (1998)
Abstract: Hydrogen-bonded ferroelectrics are modelled by a coupled spin/nonlinear lattice (polarizability) interaction Hamiltonian, where specifically the geometry of the hydrogen bond is included. The model leads to a structural phase transition and describes correctly the isotope effect due to the substitution H/D in hydrogen-bonded systems in terms of bond length changes.
Keywords: P1 Proceeding; Condensed Matter Theory (CMT)
|
“Proximity-induced pseudogap in mesoscopic superconductor/normal-metal bilayers”. Zha G-Q, Covaci L, Zhou S-P, Peeters FM, Physical review : B : condensed matter and materials physics 82, 140502 (2010). http://doi.org/10.1103/PhysRevB.82.140502
Abstract: Recent scanning tunneling microscopy (STM) measurements of the proximity effect in Au/La2−xSrxCuO4 and La1.55Sr0.45CuO4/La2−xSrxCuO4 bilayers showed a proximity-induced pseudogap [O. Yuli, I. Asulin, Y. Kalcheim, G. Koren, and O. Millo, Phys. Rev. Lett. 103, 197003 (2009)]. We describe the proximity effect in mesoscopic superconductor/normal-metal bilayers by using the Bogoliubov-de Gennes equations for a tight-binding Hamiltonian with competing antiferromagnetic and d-wave superconductivity orders. The temperature-dependent local density of states is calculated as a function of the distance from the interface. Bound state due to both d-wave and spin-density wave gaps are formed in the normal metal for energies less than the respective gaps. If there is a mismatch between the Fermi velocities in the two layers we observe that these states will shift in energy when spin-density wave order is present, thus inducing a minigap at finite energy. We conclude that the STM measurement in the proximity structures is able to distinguish between the two scenarios proposed for the pseudogap (competing or precursor to superconductivity).
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 3.836
Times cited: 7
DOI: 10.1103/PhysRevB.82.140502
|
“Pseudo magnetic field in strained graphene : revisited”. Masir MR, Moldovan D, Peeters FM, Solid state communications 175, 76 (2013). http://doi.org/10.1016/j.ssc.2013.04.001
Abstract: We revisit the theory of the pseudo magnetic field as induced by strain in graphene using the tight- binding approach. A systematic expansion of the hopping parameter and the deformation of the lattice vectors is presented from which we obtain an expression for the pseudo magnetic field for low energy electrons. We generalize and discuss previous results and propose a novel effective Hamiltonian. The contributions of the different terms to the pseudo field expression are investigated for a model triaxial strain profile and are compared with the full solution. Our work suggests that the previous proposed pseudo magnetic field expression is valid up to reasonably high strain (15%) and there is no K-dependent pseudo-magnetic field.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 1.554
Times cited: 57
DOI: 10.1016/j.ssc.2013.04.001
|
“Quantitative modeling of secondary electron emission from slow-ion bombardment on semiconductors”. Bercx M, Partoens B, Lamoen D, Physical review B 99, 085413 (2019). http://doi.org/10.1103/PhysRevB.99.085413
Abstract: When slow ions incident on a surface are neutralized, the excess potential energy is passed on to an electron inside the surface, leading to emission of secondary electrons. The microscopic description of this process, as
well as the calculation of the secondary electron yield, is a challenging problem due to its complexity as well
as its sensitivity to surface properties. One of the first quantitative descriptions was articulated in the 1950s by
Hagstrum, who based his calculation on a parametrization of the density of states of the material. In this paper, we
present a model for calculating the secondary electron yield, derived from Hagstrum’s initial approach. We use
first-principles density functional theory calculations to acquire the necessary input and introduce the concept of
electron cascades to Hagstrum’s model in order to improve the calculated spectra, as well as remove its reliance
on fitting parameters. We apply our model to He+ and Ne+ ions incident on Ge(111) and Si(111) and obtain
yield spectra that match closely to the experimental results of Hagstrum.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT); Condensed Matter Theory (CMT)
Impact Factor: 3.836
Times cited: 5
DOI: 10.1103/PhysRevB.99.085413
|
“Quantized conductance without reservoirs : method of the nonequilibrium statistical operator”. Sorée B, Magnus W, Journal of computational electronics 6, 255 (2007). http://doi.org/10.1007/s10825-006-0094-6
Abstract: We introduce a generalized non-equilibrium statistical operator (NSO) to study a current-carrying system. The NSO is used to derive a set of quantum kinetic equations based on quantum mechanical balance equations. The quantum kinetic equations are solved self-consistently together with Poissons equation to solve a general transport problem. We show that these kinetic equations can be used to rederive the Landauer formula for the conductance of a quantum point contact, without any reference to reservoirs at different chemical potentials. Instead, energy dissipation is taken into account explicitly through the electron-phonon interaction. We find that both elastic and inelastic scattering are necessary to obtain the Landauer conductance.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 1.526
DOI: 10.1007/s10825-006-0094-6
|
“Quantum and transport conductivities in monolayer graphene”. Dong HM, Xu W, Zeng Z, Lu TC, Peeters FM, Physical review : B : condensed matter and materials physics 77, 235402 (2008). http://doi.org/10.1103/PhysRevB.77.235402
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 3.836
Times cited: 31
DOI: 10.1103/PhysRevB.77.235402
|