“Modeling of the performance of BSCF capillary membranes in four-end and three-end integration mode”. Buysse C, Michielsen B, Middelkoop V, Snijkers F, Buekenhondt A, Kretzschmar J, Lenaerts S, Ceramics international 39, 4113 (2013). http://doi.org/10.1016/J.CERAMINT.2012.10.266
Abstract: Owing to their high surface-to-volume ratio, there has been an increasing research interest in mixed ionic electronic conducting (MIEC) capillary membranes for large-scale high temperature oxygen separation applications. They offer an energy-efficient solution for high temperature combustion processes in oxy-fuel and pre-combustion CO2 capture technologies used in fossil fuel power plants. In order to assess the effectiveness of these membranes in power plant applications, the impact of the geometry of Ba0.5Sr0.5Co0.8Fe0.2O3-delta (BSCF) capillaries on their performance in the three-end and four-end integration modes has been investigated and thoroughly discussed. The model's parameters were derived from four-end mode lab-scale experiments using gas-tight, macrovoid free and sulfur-free BSCF capillary membranes that were prepared by a phase-inversion spinning technique. The results of this modeling study revealed that in the four-end mode higher average oxygen fluxes and smaller total membrane areas can be obtained than in the three-end mode. This is due to the higher pO(2) gradient across the membrane wall. (C) 2012 Elsevier Ltd and Techna Group S.r.l. All rights reserved.
Keywords: A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 2.986
Times cited: 4
DOI: 10.1016/J.CERAMINT.2012.10.266
|
“CO 2 dissociation in a packed bed DBD reactor: First steps towards a better understanding of plasma catalysis”. Michielsen I, Uytdenhouwen Y, Pype J, Michielsen B, Mertens J, Reniers F, Meynen V, Bogaerts A, Chemical engineering journal 326, 477 (2017). http://doi.org/10.1016/j.cej.2017.05.177
Abstract: Plasma catalysis is gaining increasing interest for CO2 conversion, but the interaction between the plasma and catalyst is still poorly understood. This is caused by limited systematic materials research, since most works combine a plasma with commercial supported catalysts and packings. In the present paper, we study the influence of specific material and reactor properties, as well as reactor/bead configuration, on the conversion and energy efficiency of CO2 dissociation in a packed bed dielectric barrier discharge (DBD) reactor. Of the various packing materials investigated, BaTiO3 yields the highest conversion and energy efficiency, i.e., 25% and 4.5%.
Our results show that, when evaluating the influence of catalysts, the impact of the packing (support) material itself cannot be neglected, since it can largely affect the conversion and energy efficiency. This shows the large potential for further improvement of packed bed plasma reactors for CO2 conversion and other chemical conversion reactions by adjusting both packing (support) properties and catalytically active sites. Moreover, we clearly prove that comparison of results obtained in different reactor setups should be done with care, since there is a large effect of the reactor setup and reactor/bead configuration.
Keywords: A1 Journal article; Laboratory of adsorption and catalysis (LADCA); Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Impact Factor: 6.216
Times cited: 49
DOI: 10.1016/j.cej.2017.05.177
|
“C-H\cdots X (X = S, P) hydrogen bonding : the complexes of halothane with dimethyl sulfide and trimethylphosphine”. Michielsen B, Verlackt C, van der Veken BJ, Herrebout WA, Journal Of Molecular Structure 1023, 90 (2012). http://doi.org/10.1016/j.molstruc.2012.02.063
Abstract: The formation of CH⋯S and CH⋯P hydrogen bonded complexes of halothane, CHBrClCF3, with dimethyl sulfide(-d6) and trimethylphosphine(-d9) have been studied in solutions of liquid krypton using infrared and Raman spectroscopy. In the 1:1 complexes, the halothane CH stretching mode is found to be red-shifted by 43 cm−1 in the dimethyl sulfide complex, and by 63 cm−1 in the trimethylphosphine complex. The complexation enthalpies were derived and amount to −10.7(2) and −11.2(2) kJ mol−1 for the respective complexes. The experiments were supported by ab initio calculations and Monte Carlo simulations. The obtained data for the CH⋯S and CH⋯P hydrogen bonds is compared to that of corresponding CH⋯O and CH⋯N hydrogen bonds.
Keywords: A1 Journal article; Electron Microscopy for Materials Science (EMAT);
Impact Factor: 1.753
Times cited: 21
DOI: 10.1016/j.molstruc.2012.02.063
|