“Coupled plasmon modes in 2D gold nanoparticle clusters and their effect on local temperature control”. Borah R, Verbruggen SW, The journal of physical chemistry: C : nanomaterials and interfaces 123, 30594 (2019). http://doi.org/10.1021/ACS.JPCC.9B09048
Abstract: Assemblies of closely separated gold nanoparticles exhibit a strong collective plasmonic response due to coupling of the plasmon modes of the individual nanostructures. In the context of self-assembly of nanoparticles, close-packed two-dimensional (2D) clusters of spherical nanoparticles present an important composite system that promises numerous applications. The present study probes the collective plasmonic characteristics and resulting photothermal behavior of close-packed 2D Au nanoparticle clusters to delineate the effects of the cluster size, interparticle distance, and particle size. Smaller nanoparticles (20 and 40 nm in diameter) that exhibit low individual scattering and high absorption were considered for their relevance to photothermal applications. In contrast to typical literature studies, the present study compares the optical response of clusters of different sizes ranging from a single nanoparticle up to large assemblies of 61 nanoparticles. Increasing the cluster size induces significant changes to the spectral position and optophysical characteristics. Based on the model outcome, an optimal cluster size for maximum absorption per nanoparticle is also determined for enhanced photothermal effects. The effect of the particle size and interparticle distance is investigated to elucidate the nature of interaction in terms of near-field and far-field coupling. The photothermal effect resulting from absorption is compared for different cluster sizes and interparticle distances considering a homogeneous water medium. A strong dependence of the steady-state temperature of the nanoparticles on the cluster size, particle position in the cluster, incident light polarization, and interparticle distance provides new physical insight into the local temperature control of plasmonic nanostructures.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 4.536
DOI: 10.1021/ACS.JPCC.9B09048
|
“Image analysis and in situ FTIR as complementary detection tools for photocatalytic soot oxidation”. Van Hal M, Verbruggen SW, Yang X-Y, Lenaerts S, Tytgat T, Chemical engineering journal 367, 269 (2019). http://doi.org/10.1016/J.CEJ.2019.02.154
Abstract: Air pollution, especially particulate matter (PM), is an increasingly urgent problem in urban environments, causing both short and long-term health problems, climate interference and aesthetical problems due to building fouling. Photocatalysis has been shown to be a possible solution to that end. In this work two complementary detection methods for photocatalytic soot oxidation are studied and their advantages and disadvantages are discussed. First, a colour-based digital image analysis method is drastically improved towards an accurate, detailed and straightforward detection tool, that enables simultaneous measurement of the degradation of different grades of soot fouling (for instance a shallow soot haze versus condensed soot deposits). In the next part, a second soot oxidation detection method is presented based on in situ FTIR spectroscopy. This method has the additional advantage of providing more insight into the photocatalytic soot degradation process by monitoring both gaseous and adsorbed intermediates as well as reaction products while the reactions are ongoing. As an illustration, the proposed detection strategies were applied on four different commercially available and synthesized photocatalytic materials. The digital image analysis showed that P25 (Evonik) is the fastest photocatalytic soot degrader of all studied materials for both a uniform soot haze as well as concentrated soot spots. Application of the in situ method showed that for all studied materials adsorbed formate-related surface species were formed and that commercially available ZnO nanopowder has the highest specificity towards complete mineralization into CO2. With this we aim to provide a set of complementary experimental tools for the convenient, reliable, realistic and standardised detection of photocatalytic soot degradation.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 6.216
Times cited: 1
DOI: 10.1016/J.CEJ.2019.02.154
|
“Mesoporous TiO2 from poly(N,N-dimethylacrylamide)-b-polystyrene block copolymers for long-term acetaldehyde photodegradation”. Billet J, Vandewalle S, Meire M, Blommaerts N, Lommens P, Verbruggen SW, De Buysser K, Du Prez F, Van Driesche I, Journal of materials science 55, 1933 (2019). http://doi.org/10.1007/S10853-019-04024-3
Abstract: Although already some mesoporous (2–50 nm) sol–gel TiO2 synthesis strategies exist, no pore size control beyond the 12 nm range is possible without using specialized organic structure-directing agents synthetized via controlled anionic/radical polymerizations. Here, we present the use of reversible addition–fragmentation chain transfer (RAFT) polymerization as a straightforward and industrial applicable alternative to the existing controlled polymerization methods for structure-directing agent synthesis. Poly(N,N-dimethylacrylamide)-block-polystyrene (PDMA-b-PS) block copolymer, synthesized via RAFT, was chosen as structure-directing agent for the formation of the mesoporous TiO2. Crack-free thin layers TiO2 with tunable pores from 8 to 45 nm could be acquired. For the first time, in a detailed and systematic approach, the influence of the block size and dispersity of the block copolymer is experimentally screened for their influence on the final meso-TiO2 layers. As expected, the mesoporous TiO2 pore sizes showed a clear correlation to the polystyrene block size and the dispersity of the PDMA-b-PS block copolymer. Surprisingly, the dispersity of the polymer was shown not to be affecting the standard deviation of the pores. As a consequence, RAFT could be seen as a viable alternative to the aforementioned controlled polymerization reactions for the synthesis of structure-directing agents enabling the formation of mesoporous pore size-controlled TiO2. To examine the photocatalytic activity of the mesoporous TiO2 thin layers, the degradation of acetaldehyde, a known indoor pollutant, was studied. Even after 3 years of aging, the TiO2 thin layer retained most of its activity.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 2.599
Times cited: 2
DOI: 10.1007/S10853-019-04024-3
|
“Proof of concept of an upscaled photocatalytic multi-tube reactor : a combined modelling and experimental study”. van Walsem J, Roegiers J, Modde B, Lenaerts S, Denys S, Chemical engineering journal 378, 122038 (2019). http://doi.org/10.1016/J.CEJ.2019.122038
Abstract: Three upscaled multi-tube photocatalytic reactors designed for integration into HVAC (Heating, Ventilation and Air Conditioning) systems were proposed and evaluated using a CFD modelling approach, with emphasis on the flow, irradiation and concentration distribution in the reactor and hence, photocatalytic performance. Based on the obtained insights, the best reactor design was selected, further characterized and improved by an additional proof of concept study and eventually converted into practice. Subsequently, the scaled-up prototype was experimentally tested according to the CEN-EN-16846-1 standard (2017) for volatile organic compound (VOC) removal by an external scientific research center. The combined modelling and experimental approach used in this work, leads to essential insights into the design and assessment of photocatalytic reactors. Therefore, this study provides an essential step towards the optimization and commercialization of photocatalytic reactors for HVAC applications.
Keywords: A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 6.216
DOI: 10.1016/J.CEJ.2019.122038
|
“Assessing the economic potential of landfill mining : review and recommendations”. Esguerra JL, Krook J, Svensson N, Van Passel S, Detritus Volume 08 - December 2019, 1 (2019). http://doi.org/10.31025/2611-4135/2019.13883
Abstract: As landfill mining (LFM) gains public attention, systematic assessment of its economic potential is deemed necessary. The aim of this review is to critically analyze the usefulness and validity of previous economic assessments of LFM. Following the life cycle costing (LCC) framework, (i) the employed methods based on goal and scope, technical parameters and data inventory, and modelling choices were contrasted with respect to (ii) the synthesized main findings based on net profitability and economic performance drivers. Results showed that the selected studies (n=15) are mostly case study-specific and concluded that LFM has a weak economic potential, hinting at the importance of favorable market and regulation settings. However, several method issues are apparent as costs and revenues are accounted at different levels of aggregation, scope and scale-from process to sub-process level, from private to societal economics, and from laboratory to pilot-scale, respectively. Moreover, despite the inherent large uncertainties, more than half of the studies did not perform any uncertainty or sensitivity analyses posing validity issues. Consequently, this also limits the usefulness of results as individual case studies and as a collective, towards a generic understanding of LFM economics. Irrespective of case study-specific or generic aims, this review recommends that future assessments should be learning-oriented. That is, uncovering granular information about what builds up the net profitability of LFM, to be able to systematically determine promising paths for the development of cost-efficient projects.
Keywords: A1 Journal article; Engineering Management (ENM)
DOI: 10.31025/2611-4135/2019.13883
|
“Big is efficient : evidence from agricultural cooperatives in Ethiopia”. Gezahegn TW, Van Passel S, Berhanu T, D'Haese M, Maertens M, Agricultural Economics 50, 555 (2019). http://doi.org/10.1111/AGEC.12509
Abstract: In Ethiopia, there is a renewed interest in agricultural cooperatives as an institutional tool to improve the welfare of smallholder farmers. One of the pathways through which cooperatives benefit their members is scale economies. However, the establishment of cooperatives in Ethiopia seems to pay little attention to the size of the organizations. This article aims at investigating the effect of size on cost efficiency of agricultural cooperatives. More specifically, the purpose is to examine whether a single cooperative can serve a given number of farmers at a lower cost than two or more smaller cooperatives could. We employ the concept of cost subadditivity to compare the cost efficiency of large versus small cooperatives, and by extension unilateral actions. We estimate a flexible production technology using cross-sectional cooperative-level data. Findings show that costs would drop by 78% to 181% if farmers join hands in relatively large rather than small cooperatives.
Keywords: A1 Journal article; Economics; Engineering Management (ENM)
Impact Factor: 1.758
DOI: 10.1111/AGEC.12509
|
“Causal loop diagrams to systematically analyze market power in the Belgian sugar value chain”. Biely K, Mathijs E, Van Passel S, AIMS Agriculture and Food 4, 711 (2019). http://doi.org/10.3934/AGRFOOD.2019.3.711
Abstract: It has been acknowledged that power is a fundamental aspect that needs to be considered when performing a value chain analysis. The structure of the value chain is indicative of the power distribution along the chain. By employing systems thinking the structure of the value chain can be further investigated and inferences on market power issues can be made. This novel approach connects value chain research with insights from Industrial Organization (IO) literature. Depending on the case, market power may not be measurable by traditional economic tools. Systems thinking offers an alternative tool, allowing the employment of qualitative and quantitative data, overcoming drawbacks of IO methods and providing more depth to value chain analysis. In this paper the valuable contribution of systems thinking to market power analysis is exemplified by the Belgian sugar beet case. The analysis showed that transportability and perishability of sugar beet are key causes of market failure in the Belgian sugar value chain. Systems thinking can support understanding potential future behavior of the market based on the thorough understanding of the current market structure. We illustrate how to integrate factors determining the market structure into causal loop diagrams. This novel approach allows a comprehensive evaluation and thus opens up market power analysis to interdisciplinary research.
Keywords: A1 Journal article; Engineering Management (ENM)
DOI: 10.3934/AGRFOOD.2019.3.711
|
“Climate variable choice in Ricardian studies of European Agriculture”. Vaitkeviciute J, Chakir R, Van Passel S, Revue économique 70, 375 (2019). http://doi.org/10.3917/RECO.703.0375
Abstract: The Ricardian model has been employed frequently to study the impact of climate change on European agriculture. This paper contributes to this literature by using a panel data of FADN EU regions and the period 2004-2012 and by taking into account both individual heterogeneity as well as spatial autocorrelation among EU regions. We tested three hypotheses related to the degree days model. Our results show that climate outside the defined growing season matters for European agriculture, and excluding it could underestimate climate change impacts. Our results should support public policy decisions about efficient and effective mitigation and adaptation policy measures in EU agriculture.
Keywords: A1 Journal article; Economics; Engineering Management (ENM)
DOI: 10.3917/RECO.703.0375
|
“Conserving African biosphere reserves : a workshop on the valuation of ecosystem services in Man and the Biosphere Reserves”. Janssens de Bisthoven L, Rochette A-J, Verheyen E, Akpona TJ-D, Verbist B, Vanderhaegen K, Naturinda Z, Van Passel S, Berihun D, Munishi L, Hugé, J, Oryx 53, 609 (2019). http://doi.org/10.1017/S003060531900070X
Keywords: A1 Journal article; Engineering Management (ENM); Evolutionary ecology group (EVECO)
Impact Factor: 2.191
DOI: 10.1017/S003060531900070X
|
“Developing stakeholder archetypes for enhanced landfill mining”. Einhäupl P, Van Acker K, Svensson N, Van Passel S, Detritus Volume 08 - December 2019, 1 (2019). http://doi.org/10.31025/2611-4135/2019.13882
Abstract: Understanding the perspectives of different stakeholders on emerging technological concepts is an important step towards their implementation. Enhanced Landfill Mining (ELFM) is one of these emerging concepts. It aims at valorizing past waste streams to higher added values in a sustainable manner. Yet, assessment of ELFM mainly focusses on environmental and private economic issues, and societal impacts are rarely analyzed. This study uses semi-structured interviews to build understanding for different ELFM practitioners and researchers and develops five stakeholder archetypes for ELFM implementation: the Engaged Citizen, the Entrepreneur, the Technology Enthusiast, the Visionary and the Skeptic. The archetypes outline major differences in approaching ELFM implementation. The stakeholder perceptions are put into context with existing literature, and implications for ELFM implementation and future research are discussed. Results show that differences in regulatory changes and technology choices are affected by different stakeholder perspectives and more research is needed to balance inner- and inter-dimensional conflicts of ELFM's sustainability. The developed archetypes can especially be helpful when evaluating social impacts, whose perception often depends on opinion and is difficult to quantify.
Keywords: A1 Journal article; Engineering Management (ENM)
DOI: 10.31025/2611-4135/2019.13882
|
“The development of a payment regime for deep sea mining activities in the area through stakeholder participation”. Van Nijen K, Van Passel S, Brown CG, Lodge MW, Segerson K, Squires D, International Journal Of Marine And Coastal Law 34, 571 (2019). http://doi.org/10.1163/15718085-13441100
Abstract: In July 2015, the Council of the International Seabed Authority (ISA) adopted seven priority deliverables for the development of the exploitation code. The first priority was the development of a zero draft of the exploitation regulations. This article focusses on the second priority deliverable, namely the development of a payment mechanism for exploitation activities, following detailed financial and economic models based on proposed business plans. Between 2015 and 2017, five workshops have been organised with 196 active participants from 34 countries. The results so far are synthesised, drawing upon the outcome of these workshops, ISA technical papers, and the scholarly literature.
Keywords: A1 Journal article; Economics; Law; Engineering Management (ENM)
Impact Factor: 0.362
DOI: 10.1163/15718085-13441100
|
“Direct and indirect effect of irrigation water availability on crop revenue in northwest Ethiopia : a structural equation model”. Chekol Zewdie M, Van Passel S, Cools J, Tenessa DB, Ayele ZA, Tsegaye EA, Minale AS, Nyssen J, Agricultural Water Management 220, 27 (2019). http://doi.org/10.1016/J.AGWAT.2019.04.013
Abstract: Development of a clear understanding of the relationship between the availability of dam-driven irrigation water and crop revenue is important in poverty reduction and food security process. As a result, large research efforts are devoted to understanding the relationship between the availability of irrigation water and crop revenue. However, earlier studies do have several limitations. For example, without considering its indirect effect, prior studies focused solely on the direct effect of availability of irrigation water on crop revue. In this study, using a structural equation model analysis, the direct and indirect effect of availability of dam-driven irrigation water on crop revenue is decomposed and quantified specifically for the Koga irrigation scheme, located in the Mecha district of Amhara region in Ethiopia. A primary data set was collected from a randomly selected sample of 450 households in the Koga irrigation scheme. More than half of the households (254) are supported by the Koga Dam irrigation water during the dry season, and the other 196 households depended only on rainfall. The results of the study showed that, in addition to its direct effect, the availability of irrigation water indirectly affected crop revenue through receptivity of the farmers to use modern farm inputs. Around 27 percent of the total effect of dam-driven irrigation water on crop revenue was mediated by farmers’ receptivity to use yield-enhancing modern farm inputs. The results of this study suggested that the availability of irrigation water is essential to improve both crop revenue and receptivity of the farmers to use modern farm inputs. This finding also drives a strategic framework that the receptivity of the farmers to use modern farm inputs is crucial for utilizing the positive effects of irrigation water availability on crop revenue.
Keywords: A1 Journal article; Economics; Engineering Management (ENM)
Impact Factor: 2.848
Times cited: 1
DOI: 10.1016/J.AGWAT.2019.04.013
|
“Dissecting demand response : a quantile analysis of flexibility, household attitudes, and demographics”. Srivastava A, Van Passel S, Laes E, Energy Research and Social Science 52, 169 (2019). http://doi.org/10.1016/J.ERSS.2019.02.011
Abstract: Demand response (DR) can aid with grid integration of renewables, ensuring security of supply, and reducing generation costs. However, not enough is known about how residential customers’ perceptions of DR shape their response to such programs. This paper offers a deeper understanding of – and reveals the heterogeneity in – this relationship by conducting a quantile regression analysis of a Belgian DR trial, combining data on response with information on household attitudes towards smart appliances. Results overall suggest that improving response requires subtle shifts in electricity consumption behaviour, which can be achieved through changes in user perceptions. Specifically, if customers are inclined to be flexible, a stronger perception of smart appliances as being beneficial can greatly improve response. With those who are less flexible, the cost of smart appliances is a bigger concern. Thus, when designing DR programs, policymakers should aim to promote modest behaviour changes – so as to minimise inconvenience – in customers, by improving awareness on the benefits of smart appliances. Uptake of such DR programs may be improved by explaining the financial benefits or offering incentives to less flexible population segments. Lastly, improving response among older population segments will require a deeper investigation into their concerns.
Keywords: A1 Journal article; Economics; Engineering Management (ENM)
Times cited: 1
DOI: 10.1016/J.ERSS.2019.02.011
|
“Economic performance of using batteries in European residential microgrids under the net-metering scheme”. Saviuc I, Peremans H, Van Passel S, Milis K, Energies 12, 165 (2019). http://doi.org/10.3390/EN12010165
Abstract: Decentralized energy production offers an increased share of renewable energy and autonomy compared to the conventional, grid-only solution. However, under the net-metering scheme, the energy losses in batteries translate into financial losses to an investor seeking to move away from grid-only electricity and set up a residential PV+Battery microgrid. Our paper examines a hypothetical support scheme for such a project, designed to balance the economic disadvantage through partially supporting the acquisition of batteries, and thus ensure that the microgrid solution is more attractive than no investment. For this we develop four case studies based on experiments carried out in Greece, Italy, Denmark and Finland. Using the minimization of the Net Present Cost for each project, we compare the PV+Battery solution to the grid-only scenario over 25 years, for a range of electricity prices. The results illustrate first how the success of this project depends on the price of electricity. Second, we find that under current conditions in the respective countries the need for battery support varies between zero in Denmark and 86% in Italy, which reflects how the disadvantages of net metering can only be counterbalanced by either very high electricity price or very high solar resource. Our paper contributes thus to the discussion about the favourable environment for batteries in residential microgrids.
Keywords: A1 Journal article; Engineering sciences. Technology; Engineering Management (ENM)
Impact Factor: 2.262
DOI: 10.3390/EN12010165
|
“Effective bioeconomy policies for the uptake of innovative technologies under resource constraints”. Maes D, Van Passel S, Biomass &, Bioenergy 120, 91 (2019). http://doi.org/10.1016/J.BIOMBIOE.2018.11.008
Abstract: The bioeconomy is a shared vision for a future European industry entirely based on organic matter. Authorities support this technological development with subsidies and policies stimulating R&D. One major limitation for the bioeconomy is that R&D and industrial growth require the continuous availability of biomass as a primary resource. This resource dependence is already present during the formative years of new biobased innovations and influences the pilot and demonstration phase of the development. Traditionally, it is assumed that public support for pilot and demonstration initiatives may overcome this hurdle. In this paper, we investigate how this resource constraint limits the effectiveness of bioeconomy policies. The future development of the biobased sector is simulated including the inherent dependence of industrial activity on biomass. We simulate the future growth and technological diversity of an emerging biotechnological sector: the sector of manure transformation in Belgium. The paper reports the evolutions for three policy scenarios. The model explicitly accounts for endogenous innovation and knowledge transfer mechanisms. The results show that policies may have an important impact on the sector structure in the long run, but the sector growth remains ultimately constrained by the availability of inputs. So bioeconomy policies to promote innovation will be less effective, unless mechanisms are included to alleviate the resource constraint.
Keywords: A1 Journal article; Engineering sciences. Technology; Engineering Management (ENM)
Impact Factor: 3.219
Times cited: 3
DOI: 10.1016/J.BIOMBIOE.2018.11.008
|
“Eliciting stakeholder needs : an anticipatory approach assessing enhanced landfill mining”. Einhäupl PV, Krook J, Svensson N, Van Acker K, Van Passel S, Waste Management 98, 113 (2019). http://doi.org/10.1016/J.WASMAN.2019.08.009
Abstract: Landfill owners, governmental institutions, technology providers, academia and local communities are important stakeholders involved in Enhanced Landfill Mining (ELFM). This concept of excavating and processing historical waste streams to higher added values can be seen as a continuation of traditional landfill mining (LFM) and seems to be an innovative and promising idea for potential environmental and societal benefits. However, ELFM's profitability is still under debate, and environmental as well as societal impacts have to be further investigated. This study provides a first step towards an anticipatory approach, assessing ELFM through stakeholder integration. In the study, semi-structured interviews were conducted with various stakeholders, involved in a case study in Flanders, Belgium. Participants were selected across a quadruple helix (QH) framework, i.e. industrial, governmental, scientific, and local community actors. The research comprises 13 interviews conducted with an aim to elicit stakeholder needs for ELFM implementation using a general inductive approach. In total 18 different stakeholder needs were identified. The paper explains how the stakeholder needs refer to the different dimensions of sustainability, which groups of stakeholders they primarily affect, and what types of uncertainty could be influenced by their implementation. The stakeholder needs are structured into societal, environmental, regulatory and techno-economic needs. Results show additional economic, environmental, and societal aspects of ELFM to be integrated into ELFM research, as well as a need for the dynamic modeling of impacts. (C) 2019 Elsevier Ltd. All rights reserved.
Keywords: A1 Journal article; Engineering sciences. Technology; Engineering Management (ENM)
Impact Factor: 4.03
Times cited: 3
DOI: 10.1016/J.WASMAN.2019.08.009
|
“The future of Ex-Ante LCA? Lessons learned and practical recommendations”. Buyle M, Audenaert A, Billen P, Boonen K, Van Passel S, Sustainability 11, 5456 (2019). http://doi.org/10.3390/SU11195456
Abstract: Every decision-oriented life cycle assessment (LCAs) entails, at least to some extent, a future-oriented feature. However, apart from the ex-ante LCAs, the majority of LCA studies are retrospective in nature and do not explicitly account for possible future effects. In this review a generic theoretical framework is proposed as a guideline for ex-ante LCA. This framework includes the entire technology life cycle, from the early design phase up to continuous improvements of mature technologies, including their market penetration. The compatibility with commonly applied system models yields an additional aspect of the framework. Practical methods and procedures are categorised, based on how they incorporate future-oriented features in LCA. The results indicate that most of the ex-ante LCAs focus on emerging technologies that have already gone through some research cycles within narrowly defined system boundaries. There is a lack of attention given to technologies that are at a very early development stage, when all options are still open and can be explored at a low cost. It is also acknowledged that technological learning impacts the financial and environmental performance of mature production systems. Once technologies are entering the market, shifts in market composition can lead to substantial changes in environmental performance.
Keywords: A1 Journal article; Engineering sciences. Technology; Engineering Management (ENM); Biochemical Wastewater Valorization & Engineering (BioWaVE); Energy and Materials in Infrastructure and Buildings (EMIB)
Impact Factor: 1.789
Times cited: 4
DOI: 10.3390/SU11195456
|
“How to assess the potential of emerging green technologies? Towards a prospective environmental and techno-economic assessment framework”. Thomassen G, Van Dael M, Van Passel S, You F, Green Chemistry 21, 4868 (2019). http://doi.org/10.1039/C9GC02223F
Abstract: For sustainable production and consumption, emerging green technologies need to be optimized towards a minimal environmental impact and a maximal economic impact. In an early stage of technology development, more flexibility is available to adapt the technology. Therefore, a prospective environmental and techno-economic assessment is required. The prospective assessment differs at the different stages of technology development, as also the data availability and accuracy evolves. This paper reviews the different prospective technological, economic and environmental assessment methods which have been used to assess the potential of new green chemical technologies. Based on the current best practices, an overarching framework is introduced to assess the technological, economic and environmental potential of an emerging green chemical technology at the different stages of technology development.
Keywords: A1 Journal article; Engineering sciences. Technology; Engineering Management (ENM)
Impact Factor: 9.125
Times cited: 5
DOI: 10.1039/C9GC02223F
|
“Impacts of the hydropower-controlled Tana-Beles interbasin water transfer on downstream rural livelihoods (northwest Ethiopia)”. Annys S, Adgo E, Ghebreyohannes T, Van Passel S, Dessein J, Nyssen J, Journal Of Hydrology 569, 436 (2019). http://doi.org/10.1016/J.JHYDROL.2018.12.012
Abstract: Despite public awareness of unintended impacts (1980s) and well-developed international standards (2000s), downstream impacts of large hydropower projects still very often are not properly assessed. Impacts of (hydropower-regulated) interbasin water transfers (IBWTs) are considered self-evidently positive, although they can have far-reaching consequences for hydrogeomorphological systems and consequently river-dependent communities. In this study, the downstream direct and indirect impacts of the Ethiopian hydropower-regulated Tana-Beles IBWT are evaluated in an interdisciplinary way. The components of the framework of rural livelihoods are considered and changing contexts, resources availabilities and livelihood strategies are analysed. Mixed methods are applied, combining hydrogeomorphological field observations, GIS analyses, scientific literature, policy documents, and semi-structured interviews with local people and local to federal authorities. Results show that the IBWT drastically increased the Beles rivers discharge (with an average release of +92 m3 s−1 at the outlet; *2 in rainy season and *12 in dry season 100 km downstream of the water release) and introduced dangerous situations for local communities (over 250 people drowned in the river). River bank erosion resulted in the uncompensated loss of farmland (163 ha) and the establishment of large-scale commercial farms increased the pressure on land and led to the impoverishment of displaced communities (4310 households). The project was implemented top-down, without any transparency, benefit sharing or compensation for external costs. This stresses the importance of downstream interdisciplinary impact assessments and highlights the need for decent in-depth ex post-analyses of hydropower projects. Environmental impact assessments should be taken seriously and cannot be considered a formality. In Ethiopia and in many developing countries, the hydropower industry is booming. Although dams and IBWTs can be the best solution for water-related problems in specific contexts, national development goals (such as the expansion of the electricity network) should not be at the expense of rural livelihoods.
Keywords: A1 Journal article; Economics; Engineering sciences. Technology; Engineering Management (ENM)
Impact Factor: 3.483
Times cited: 2
DOI: 10.1016/J.JHYDROL.2018.12.012
|
“Integration of resource recovery into current waste management through (enhanced) landfill mining”. Hernandez Parrodi JC, Lucas H, Gigantino M, Sauve G, Esguerra JL, Einhäupl P, Vollprecht D, Pomberger R, Friedrich B, Van Acker K, Krook J, Svensson N, Van Passel S, Detritus Volume 08 - December 2019, 1 (2019). http://doi.org/10.31025/2611-4135/2019.13884
Abstract: Europe has somewhere between 150,000 and 500,000 landfill sites, with an estimated 90% of them being “non-sanitary” landfills, predating the EU Landfill Directive of 1999/31/EC. These older landfills tend to be filled with municipal solid waste and often lack any environmental protection technology. “ Doing nothing”, state-of-theart aftercare or remediating them depends largely on technical, societal and economic conditions which vary between countries. Beside “ doing nothing' and landfill aftercare, there are different scenarios in landfill mining, from re-landfilling the waste into ”sanitary landfills" to seizing the opportunity for a combined resource-recovery and remediation strategy. This review article addresses present and future issues and potential opportunities for landfill mining as an embedded strategy in current waste management systems through a multi-disciplinary approach. In particular, three general landfill mining strategies are addressed with varying extents of resource recovery. These are discussed in relation to the main targets of landfill mining: (i) reduction of the landfill volume (technical), (ii) reduction of risks and impacts (environmental) and (iii) increase in resource recovery and overall profitability (economic). Geophysical methods could be used to determine the characteristics of the landfilled waste and subsurface structures without the need of an invasive exploration, which could greatly reduce exploration costs and time, as well as be useful to develop a procedure to either discard or select the most appropriate sites for (E)LFM. Material and energy recovery from land-filled waste can be achieved through mechanical processing coupled with thermochemical valorization technologies and residues upcycling techniques. Gasification could enable the upcycling of residues after thermal treatment into a new range of eco-friendly construction materials based on inorganic polymers and glass-ceramics. The multi-criteria assessment is directly influenced by waste- and technology related factors, which together with site-specific conditions, market and regulatory aspects, influence the environmental, economic and societal impacts of (E)LFM projects.
Keywords: A1 Journal article; Engineering Management (ENM)
Times cited: 1
DOI: 10.31025/2611-4135/2019.13884
|
“Modelling environmental impacts of treated municipal wastewater reuse for tree crops irrigation in the Mediterranean coastal region”. Moretti M, Van Passel S, Camposeo S, Pedrero F, Dogot T, Lebailly P, Vivaldi GA, Science Of The Total Environment 660, 1513 (2019). http://doi.org/10.1016/J.SCITOTENV.2019.01.043
Abstract: Wastewater reuse provides valuable solutions to solve the societal challenges of decreasing availability and limiting access to secure water resources. The present study quantifies the environmental performance of nectarine orchards irrigation using treated municipal wastewater (TMW) and surface water using a unique dataset based on field experimental data. Climate change, toxicity (for human and freshwater), eutrophication (marine and freshwater) and acidification impacts were analysed using the impact assessment method suggested by the International Reference Life Cycle Data System (ILCD). The water footprint associated to the life cycles of each system has been estimated using the Available WAter REmaining (AWARE) method. Monte Carlo simulation was used to assess data uncertainty. The irrigation of nectarine orchards using TMW performs better than the irrigation using surface water for eutrophication impact categories. Compared with surface water resources, the potential impacts of TMW reuse in agriculture on climate change and toxicity are affected by the wastewater treatment phase (WWT). Only eutrophication and acidification burdens are generated by in-field substitution of surface water with TMW. Considering human and ecosystem water demand, the irrigation with TMW increases water consumption of 19.12 m3 per kg of nectarine produced. Whereas, it shows a positive contribution to water stress (−0.19 m3) if only human water demand is considered. This study provides important results that allow for a better understanding of the potential environmental consequences of TMW reuse in agriculture. It suggests that embracing the type of WWTs, the replacement of fertilizers, the effects on water scarcity and ecosystem quality might be useful to redefine water reuse regulations and increase public acceptance for the reuse of TMW in agriculture. Moreover, this study reveals the need for developing consensus and standardized guidance for life cycle analysis of water reuse applications.
Keywords: A1 Journal article; Economics; Engineering sciences. Technology; Engineering Management (ENM)
Impact Factor: 4.9
Times cited: 4
DOI: 10.1016/J.SCITOTENV.2019.01.043
|
“A multi-objective optimization-extended techno-economic assessment : exploring the optimal microalgal-based value chain”. Thomassen G, Van Dael M, You F, Van Passel S, Green Chemistry 21, 5945 (2019). http://doi.org/10.1039/C9GC03071A
Abstract: The use of fossil-based products induces a large environmental burden. To lighten this burden, green technologies are required that can replace their fossil-based counterparts. To enable the development of economically viable green technologies, an optimization towards both economic and environmental objectives is required. To perform this multi-objective optimization (MOO), the environmental techno-economic assessment (ETEA) methodology is extended towards a MOO-extended ETEA. The development of this MOO-extended ETEA is the main objective of this manuscript. As an example of a green technology, the concept of microalgae biorefineries is used as a case study to illustrate the MOO-extended ETEA. According to the results, all optimal value chains include open pond cultivation, a membrane for medium recycling and spray drying. The optimal economic value chain uses Nannochloropsis sp. in a one-stage cultivation to produce fish larvae feed, while the optimal environmental design uses Dunaliella salina or Haematococcus pluvialis to produce carotenoids and fertilizer or energy products, by means of anaerobic digestion or gasification. The crucial parameters for both environmental and economic feasibility are the content, price and reference impact of the main end product, the growth parameters and the biomass and carotenoid recovery efficiency alongside the different process steps. By identifying the economic and environmentally optimal algal-based value chain and the crucial drivers, the MOO-extended ETEA provides insights on how algae-based value chains can be developed in the most economic and environmentally-friendly way. For example, the inclusion of a medium recycling step to lower the water and salt consumption is required in all Pareto-optimal scenarios. Another major insight is the requirement of high-value products such as carotenoids or specialty food to obtain and economically and environmentally feasible algal-based value chain. Due to the modular nature of the MOO-extended ETEA, multiple processes can be included or excluded from the superstructure. Although this case study is limited to current microalgae biorefinery technologies, the MOO-extended ETEA can also be used to assess the economic and environmental effect of more innovative technologies. This way, the MOO-extended ETEA provides a methodology to assess the economic and environmental potential of innovative green technologies and shorten their time-to-market.
Keywords: A1 Journal article; Economics; Engineering sciences. Technology; Engineering Management (ENM)
Impact Factor: 9.125
Times cited: 1
DOI: 10.1039/C9GC03071A
|
“Relationship between farmers' perception of sustainability and future farming strategies : a commodity-level comparison”. Creemers S, Van Passel S, Vigani M, Vlahos G, AIMS Agriculture and Food 4, 613 (2019). http://doi.org/10.3934/AGRFOOD.2019.3.613
Abstract: The environmental challenges have become increasingly integrated into the European Union's Common Agricultural Policy (CAP). The Europe 2020 CAP Framework defines new rules for farmers and targets on innovation, resource efficiency, economic viability, and environmental sustainability. Given the continual evolution of the CAP, it is relevant to focus on sustainable agriculture and which indicators can be employed to aid our understanding of the future farming strategies. This study examines the relationship between perceived sustainability and future farming strategies for three different commodities: sugar beet, dairy, and feta cheese. Survey data collected between 2017-2018 from 191 Belgian sugar beet farmers, 524 dairy farmers (from UK, Denmark, France, and Latvia), and 150 Greek sheep and goat farmers producing milk for feta cheese were analysed using multinomial logistic regressions. Our results show that the farmers' attitude towards sustainability affects intentions to implement specific farming strategies. Belgian sugar beet farmers who perceive their supply chain arrangements (SCAs) environmentally sustainable are less likely to reduce the scale of their farms' operations rather than to maintain them. Dairy farmers are more likely to change the existing scale than to maintain scale if they perceive that production choices affect environmental sustainability to a higher extent. Dairy farmers who perceive their SCAs economically sustainable are less likely to abandon farming. Greek sheep and goat farmers who perceive their SCAs economically sustainable are more likely to expand the existing scale. The observed differences at commodity-level show the importance of well targeted policy measures towards more sustainable farming systems in the European Union.
Keywords: A1 Journal article; Engineering Management (ENM)
Times cited: 1
DOI: 10.3934/AGRFOOD.2019.3.613
|
“Sustainability indicators for biobased chemicals : a Delphi study using multi-criteria decision analysis”. Van Schoubroeck S, Springael J, Van Dael M, Malina R, Van Passel S, Resources Conservation And Recycling 144, 198 (2019). http://doi.org/10.1016/J.RESCONREC.2018.12.024
Abstract: Biobased chemistry has gained interest and has the potential to tackle some of the sustainability challenges the chemical industry must endure. Sustainability impacts need to be evaluated and monitored to highlight the advantages and pitfalls of different biobased routes over the entire product life cycle. This study aims for expert consensus concerning indicators needed and preferred for sustainability analysis of biobased chemicals in Europe. Experts are consulted by means of a Delphi method with stakeholders selected from three core groups: the private, public and academic sector. Best-Worst Scaling (BWS) is performed to gather data on the prioritization of the sustainability indicators per respondent. Afterwards, Multi-Criteria Decision Analysis (MCDA) is used to develop a consensus ranking among the experts. The results show that GHG emissions, market potential and acceptance of biobased materials are deemed the most crucial indicators for respectively environmental, economic and social sustainability. Expert consensus is positive in all three sustainability domains, with the strongest consensus measured for environmental sustainability showing a median Kendalls τ of 0.63 (τ ranging from -1 to 1) and the weakest consensus found within social sustainability showing a median Kendalls τ of 0.50. Further research can apply the ranked indicators on specific case studies to evaluate the practicability of the defined indicator set.
Keywords: A1 Journal article; Economics; Engineering sciences. Technology; Engineering Management (ENM)
Impact Factor: 3.313
Times cited: 4
DOI: 10.1016/J.RESCONREC.2018.12.024
|
“Take out the farmer: An economic assessment of land expropriation for urban expansion in Bahir Dar, Northwest Ethiopia”. Admasu WF, Van Passel S, Minale AS, Tsegaye EA, Azadi H, Nyssen J, Land Use Policy 87, 104038 (2019). http://doi.org/10.1016/J.LANDUSEPOL.2019.104038
Abstract: In Ethiopia, the demand for land for urbanisation is primarily met by converting rural land through expropriation. However, land expropriations are adversely affecting the previous land users by reducing the amount of production and their sources of income. In Bahir Dar, one of the fastest-growing cities in Ethiopia, approximately 300 landholdings are expropriated each year, on average, for urban expansion. This paper assesses the land expropriations to examine whether they offer economically appropriate compensation for the previous land users. Land expropriations for urbanisation between 2007/2008 and 2016/2017 were analysed based on data on land expropriation and its compensation payment obtained from the Bahir Dar City Land Administration and Management Office. Data were analysed using an exponential growth model and a stochastic budgeting technique in which Monte Carlo simulations are performed. Between 2007/2008 and 2016/2017, more than 1500 ha of land were included in the city's boundary through expropriation from 2900 landholders. The affected farmers received compensation that represents only 37 per cent of the value of current crop yields and its growth. The current compensation scheme ignores the impact of inflation on the prices of crops and assumes constant yields. It also excludes the value of crop residuals. We propose a workable discounted compensation framework that considers crop price and yield growths. This will make the compensation scheme more appropriate and make the affected farmers better off.
Keywords: A1 Journal article; Engineering Management (ENM)
Impact Factor: 3.089
Times cited: 1
DOI: 10.1016/J.LANDUSEPOL.2019.104038
|
“Towards a more direct policy feedback in circular economy monitoring via a societal needs perspective”. Alaerts L, Van Acker K, Rousseau S, De Jaeger S, Moraga G, Dewulf J, De Meester S, Van Passel S, Compernolle T, Bachus K, Vrancken K, Eyckmans J, Resources, conservation and recycling 149, 363 (2019). http://doi.org/10.1016/J.RESCONREC.2019.06.004
Abstract: The increasing focus on circular economy at the level of governments and policy requires the development of appropriate indicators to effectively monitor the progress towards the circular economy. Currently two very different types of indicator areas are under development: (i) monitoring frameworks based on macro indicators that summarize the progress at (supra)national level, and (ii) micro indicators tailored towards assessing circularity at the level of products. It is not possible to obtain sufficiently direct feedback about the impact of policy interventions by either macro or micro indicators alone. In this paper, a conceptual approach is developed that aims to bridge the gap between the micro and macro level with meso level indicators, and thus ultimately deliver more direct feedback for policymakers, via the insertion of an extra level of meso indicators in between the macro and the micro level. These indicators have been extracted from a dedicated workshop that involved policy, sector and societal stakeholders. The aim of these indicators is to report on progress towards circular economy objectives based on the fulfillment of societal needs. In this way the consumption perspective is given a central position, and the role of circular business models is acknowledged. Following the development of the concept, the next steps towards tailored, flexible and agile monitoring frameworks for circular economy at (supra)national and regional level are outlined. The paper concludes with an illustrative example of the framework applied to the mobility system.
Keywords: A1 Journal article; Economics; Engineering Management (ENM); Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 3.313
Times cited: 1
DOI: 10.1016/J.RESCONREC.2019.06.004
|
“Win-win possibilities through capacity tariffs and battery storage in microgrids”. Milis K, Peremans H, Springael J, Van Passel S, Renewable &, Sustainable Energy Reviews 113, 109238 (2019). http://doi.org/10.1016/J.RSER.2019.06.045
Abstract: This paper investigates the impact of capacity tariff design on microgrids. While the possible benefits for utilities of capacity tariffs are well researched, comparatively little work has been done investigating the effects of capacity pricing on prosumers. Through simulating a grid connected microgrid and solving the day-ahead dispatch problem for a calendar year, we show that a well-designed capacity tariff will not only smooth out demand profiles, but could also lead to less erratic charge/discharge cycles in a real-time pricing scenario, lessening battery degradation. These results show that a properly designed capacity tariff has the potential to be beneficial for both the utilities as well as the battery-owning prosumer. Furthermore, we propose a new, heuristic approach to solve the day-ahead economic dispatch problem, which we prove to be effective and efficient. Additionally, we demonstrate that our novel approach does not impose mathematical restrictions such as continuous differentiability of the objective function. We show that the proposed capacity tariff achieves the stated aim of promoting battery storage uptake and that our novel method allows for compression and shorter run times.
Keywords: A1 Journal article; Economics; Engineering sciences. Technology; Engineering Management (ENM)
Impact Factor: 8.05
Times cited: 1
DOI: 10.1016/J.RSER.2019.06.045
|
“A 2D model of a gliding arc discharge for CO2conversion”. Paunska T, Trenchev G, Bogaerts A, Kolev S, AIP conference proceedings
T2 –, 10th Jubilee Conference of the Balkan-Physical-Union (BPU), AUG 26-30, 2018, Sofia, BULGARIA (2019). http://doi.org/10.1063/1.5091186
Abstract: The study presents a 2D fluid plasma model of a gliding arc discharge for dissociation of CO2 which allows its subsequent conversion into value-added chemicals. The model is based on the balance equations of charged and neutral particles, the electron energy balance equation, the gas thermal balance equation and the current continuity equation. By choosing the modeling domain to be the plane perpendicular to the arc current, the numerical calculations are significantly simplified. Thus, the model allows us to explore the influence of the gas instabilities (turbulences) on the energy efficiency of CO2 conversion. This paper presents results for plasma parameters at different values of the effective turbulent thermal conductivity leading to enhanced energy transport.
Keywords: P1 Proceeding; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
DOI: 10.1063/1.5091186
|
Yao X (2019) An advanced TEM study on quantification of Ni4Ti3 precipitates in low temperature aged Ni-Ti shape memory alloy. 149 p
Keywords: Doctoral thesis; Electron microscopy for materials research (EMAT)
|
“Applications of plasma-liquid systems : a review”. Rezaei F, Vanraes P, Nikiforov A, Morent R, De Geyter N, Materials 12, 2751 (2019). http://doi.org/10.3390/MA12172751
Abstract: Plasma-liquid systems have attracted increasing attention in recent years, owing to their high potential in material processing and nanoscience, environmental remediation, sterilization, biomedicine, and food applications. Due to the multidisciplinary character of this scientific field and due to its broad range of established and promising applications, an updated overview is required, addressing the various applications of plasma-liquid systems till now. In the present review, after a brief historical introduction on this important research field, the authors aimed to bring together a wide range of applications of plasma-liquid systems, including nanomaterial processing, water analytical chemistry, water purification, plasma sterilization, plasma medicine, food preservation and agricultural processing, power transformers for high voltage switching, and polymer solution treatment. Although the general understanding of plasma-liquid interactions and their applications has grown significantly in recent decades, it is aimed here to give an updated overview on the possible applications of plasma-liquid systems. This review can be used as a guide for researchers from different fields to gain insight in the history and state-of-the-art of plasma-liquid interactions and to obtain an overview on the acquired knowledge in this field up to now.
Keywords: A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Impact Factor: 2.654
Times cited: 4
DOI: 10.3390/MA12172751
|