Abstract: The discharge properties of the plasma bulk flow near the surface of heated compound-materials strongly affects the kinetic layer parameters modeled and manifested in the Knudsen layer. This paper extends the widely used two-layer kinetic ablation model to the ablation controlled non-equilibrium discharge due to the fact that the local thermodynamic equilibrium (LTE) approximation is often violated as a result of the interaction between the plasma and solid walls. Modifications to the governing set of equations, to account for this effect, are derived and presented by assuming that the temperature of the electrons deviates from that of the heavy particles. The ablation characteristics of one typical material, polytetrafluoroethylene (PTFE) are calculated with this improved model. The internal degrees of freedom as well as the average particle mass and specific heat ratio of the polyatomic vapor, which strongly depends on the temperature, pressure and plasma non-equilibrium degree and plays a crucial role in the accurate determination of the ablation behavior by this model, are also taken into account. Our assessment showed the significance of including such modifications related to the non-equilibrium effect in the study of vaporization of heated compound materials in ablation controlled arcs. Additionally, a two-temperature magneto-hydrodynamic (MHD) model accounting for the thermal non-equilibrium occurring near the wall surface is developed and applied into an ablation-dominated discharge for an electro-thermal chemical launch device. Special attention is paid to the interaction between the non-equilibrium plasma and the solid propellant surface. Both the mass exchange process caused by the wall ablation and plasma species deposition as well as the associated momentum and energy exchange processes are taken into account. A detailed comparison of the results of the non-equilibrium model with those of an equilibrium model is presented. The non-equilibrium results show a non-equilibrium region near the plasma-wall interaction region and this indicates the need for the consideration of the influence of the possible departure from LTE in the plasma bulk on the determination of ablation rate.

Abstract: The quantum anomalous Hall (QAH) effect is a topologically nontrivial phase, characterized by a non-zero Chern number defined in the bulk and chiral edge states in the boundary. Using first-principles calculations, we demonstrate the presence of the QAH effect in a 1T-YN2 monolayer, which was recently predicted to be a Dirac half metal without spin-orbit coupling (SOC). We show that the inclusion of SOC opens up a large nontrivial bandgap of nearly 0.1 eV in the electronic band structure. This results in the nontrivial bulk topology, which is confirmed by the calculation of Berry curvature, anomalous Hall conductance and the presence of chiral edge states. Remarkably, a QAH phase of high Chern number C = 3 is found, and there are three corresponding gapless chiral edge states emerging inside the bulk gap. Different substrates are also chosen to study the possible experimental realization of the 1T-YN2 monolayer, while retaining its nontrivial topological properties. Our results open a new avenue in searching for QAH insulators with high temperature and high Chern numbers, which can have nontrivial practical applications.

Abstract: A novel two-dimensional (2D) structurally stable carbon allotrope is proposed using first-principles calculations, which is a promising material for water purification and for electronic devices due to its unique porous structure and electronic properties. Rectangular and hexagonal rings are connected with acetylenic linkages, forming a nanoporous structure with a pore size of 6.41 angstrom, which is known as T-4,T-4,T-4-graphyne. This 2D sheet exhibits a direct bandgap of 0.63 eV at the M point, which originates from the p(z)( )atomic orbitals of carbon atoms as confirmed by a tight-binding model. Importantly, T-4,T-4,T-4-graphyne is found to be energetically more preferable than the experimentally realized beta-graphdiyne, it is dynamically stable and can withstand temperatures up to 1500 K.

Abstract: Packed bed dielectric barrier discharge (PB-DBD) plasma reactors are very promising for various plasma catalysis applications, but the exact mechanisms of plasma-catalyst interaction are far from understood, because the plasma discharge and catalyst/packing properties are mutually dependent. To better understand the effect of packing dielectric material on the electrical plasma properties, we study here a single bead DBD plasma reactor operating in dry air, with beads of different dielectric constant and for different applied voltages, by means of fluid modelling validated by optical imaging experiments. Our study reveals that the plasma in the single bead DBD reactor can manifest itself in two different modalities, i.e. (a) polar discharges at the bead poles in contact with the electrodes, and (b) a streamer discharge caused by surface ionization waves, which bridges the gas gap. Beads with high dielectric constant result in localised electric field enhancement and hence yield a reduction of the applied voltage required for plasma production. At low applied voltage, the discharge appears as polar discharges between the bead and the electrodes, and upon higher voltage it undergoes a transition into a bridging streamer discharge. The transition voltage to the streamer mode rises for beads with higher dielectric constant. These observations are important for plasma catalysis applications. A higher dielectric constant yields a higher electric field and thus higher average electron energy and density, giving rise to more reactive species, but it also yields a confined discharge near the contact points of packing beads, limiting the interaction area between the catalyst and the active plasma species. In addition, our model reveals that the dielectric bead behaves as a capacitor and traps charges, which can explain the significant occurrence of partial discharging in PB-DBDs and non-parallelogram shaped Lissajous plots. Hence, equivalent circuit modelling of PB-DBDs should take into account the role of packing beads in charge trapping as a capacitor.