|
“HRTEM studies of dislocations in cubic BN”. Nistor LC, Van Tendeloo G, Dincã, G, Physica status solidi: A: applied research 201, 2578 (2004). http://doi.org/10.1002/pssa.200405192
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Times cited: 8
DOI: 10.1002/pssa.200405192
|
|
|
“Direct observation of laser-induced crystallization of a-C : H films”. Nistor LC, van Landuyt J, Ralchenko VG, Kononenko TV, Obraztsova ED, Strelnitsky VE, Applied physics A : materials science &, processing 58, 137 (1994). http://doi.org/10.1007/BF00332170
Abstract: The post-growth modification of diamond-like amorphous hydrogenated carbon a-C:H films by laser treatment has been studied by transmission electron microscopy and Raman spectroscopy. a-C:H films grown on Si substrates by benzene decomposition in a rf glow discharge were irradiated with 15 ns pulses of a KrF-excimer laser with fluences in the ran e of E = 50-700 mJ/cm(2). At fluences below 100 mJ/cm(2) an increase in the number of graphitic clusters and in their ordering was evidenced from Raman spectra, while the film structure remained amorphous according to electron microscopy and electron diffraction observations. At higher fluences the appearance of diamond particles of 2-7 nm size, embedded into the lower crystallized graphitic matrix, was observed and simultaneously a progressive growth of graphite nanocrystals with dimensions from 2 nm to 4 nm was deduced from Raman measurements. The maximum thickness of the crystallized surface layer (approximate to 400 nm) and the degree of laser annealing are limited by the film ablation which starts at E > 250 mJ/cm(2). The laser-treated areas lose their chemical inertness. In particular, chemical etching in chromium acid becomes possible, which may be used for patterning the highly inert carbon films.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Times cited: 73
DOI: 10.1007/BF00332170
|
|
|
“Growth and characterization of a-axis textured ZnO thin films”. Nistor LC, Ghica C, Matei D, Dinescu G, Dinescu M, Van Tendeloo G, Journal of crystal growth 277, 26 (2005). http://doi.org/10.1016/j.jcrysgro.2004.12.162
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 1.751
Times cited: 44
DOI: 10.1016/j.jcrysgro.2004.12.162
|
|
|
“Thermal stability of atomic layer deposited Zr:Al mixed oxide thin films: an in situ transmission electron microscopy study”. Nistor LC, Richard O, Zhao C, Bender H, Van Tendeloo G, Journal of materials research 20, 1741 (2005). http://doi.org/10.1557/JMR.2005.0217
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 1.673
DOI: 10.1557/JMR.2005.0217
|
|
|
“Strain mapping around dislocations in diamond and cBN”. Willems B, Nistor L, Ghica C, Van Tendeloo G, Physica status solidi: A: applied research 202, 2224 (2005). http://doi.org/10.1002/pssa.200561923
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Times cited: 4
DOI: 10.1002/pssa.200561923
|
|
|
“Crystallographic aspects related to advanced tribological multilayers of Cr/CrN and Ti/TiN types produced by pulsed laser deposition (PLD)”. Major L, Morgiel J, Major B, Lackner JM, Waldhauser W, Ebner R, Nistor L, Van Tendeloo G, Surface and coatings technology 200, 6190 (2006). http://doi.org/10.1016/j.surfcoat.2005.11.021
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 2.589
Times cited: 32
DOI: 10.1016/j.surfcoat.2005.11.021
|
|
|
“Characterization of {111} planar defects induced in silicon by hydrogen plasma treatments”. Ghica C, Nistor LC, Bender H, Richard O, Van Tendeloo G, Ulyashin A;, Philosophical magazine 86, 5137 (2006). http://doi.org/10.1080/14786430600801443
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 1.505
Times cited: 12
DOI: 10.1080/14786430600801443
|
|
|
“TEM characterization of extended defects induced in Si wafers by H-plasma treatment”. Ghica C, Nistor LC, Bender H, Richard O, Van Tendeloo G, Ulyashin A, Journal of physics: D: applied physics 40, 395 (2007). http://doi.org/10.1088/0022-3727/40/2/016
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 2.588
Times cited: 10
DOI: 10.1088/0022-3727/40/2/016
|
|
|
“Atomic imaging of cage like structures of silicon”. Nistor L, Van Tendeloo G, Amelinckx S, Cros C, Physica status solidi: A: applied research 146, 119 (1994). http://doi.org/10.1002/pssa.2211460111
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Times cited: 12
DOI: 10.1002/pssa.2211460111
|
|
|
“Mesoseopic ordering in the 0.9 Pb(Mg1/3Nb2/3)O3-0.1 PbTiO3 relaxor ferroelectric : a HRTEM study”. Nistor LC, Ghica C, Van Tendeloo G, Physica status solidi: C: conferences and critical reviews 4, 736 (2007). http://doi.org/10.1002/pssc.200673753
Abstract: We report a microstructural and compositional study of a 90% Pb(Mg1/3Nb2/3)O-3 – 10% PbTiO3 ceramic sample. High resolution transmission electron microscopy (HRTEM) revealed the presence of compositional ordered nano-domains (1 – 4 mn), observable in two specific orientations, [0 (1) over bar 1] and [1 1 (2) over bar]. However, the visibility and the ordering degree of the nano-domains on the HRTEM images are not at all obvious. Fourier filtering of the images clearly revealed the ordered domains. Antiphase boundaries lying in the (111) planes separate them, while (100) and (111) facets separate the ordered domains from the disordered matrix. Their shape is plate-like, not uniformly spread in the disordered matrix. Their average size varies in different regions of the sample, most probably due to a non-uniform distribution of Ti, as observed by energy dispersive X-ray spectroscopy. (c) 2007 WILEY-VCH Verlag GmbH Co. KGaA, Weinheim.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Times cited: 2
DOI: 10.1002/pssc.200673753
|
|
|
“The study of a crater forming on the surface of a Ti target submitted to multipulse excimer laser irradiation under low pressure N2”. Teodorescu VS, Mihailescu IN, Gyorgy E, Luches A, Martino M, Nistor LC, van Landuyt J, Hermann J, Journal of modern optics 43, 1773 (1996). http://doi.org/10.1080/095003496154815
Abstract: A Ti target was submitted to laser ablation in low ambient pressure N-2. Electron microscopy examination of the cross-section of the crater zone forming on the Ti target, and XPS analyses, indicate that there is a small effect on the nitridation processes taking place on and in the vicinity of the target. The studies show a zone influenced by the multipulse laser treatment extending beneath the crater down to a depth of the same order of magnitude as the crater depth (i.e. similar to 10 mu m). In this zone, TiN could be identified as being present only in traces, while the whole zone exhibited a layer structure with differences in morphology and mechanical wear.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 1.008
Times cited: 11
DOI: 10.1080/095003496154815
|
|
|
“Crystallographic aspects related to the high pressure-high temperature phase transformation of boron nitride”. Nistor LC, Van Tendeloo G, Dincã, G, Philosophical magazine 85, 1145 (2005). http://doi.org/10.1080/14786430412331325058
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 1.505
Times cited: 13
DOI: 10.1080/14786430412331325058
|
|
|
“The ferroelectric phase transition in tridymite type BaAl2O4 studied by electron microscopy”. Abakumov AM, Lebedev OI, Nistor L, Van Tendeloo G, Amelinckx S, Phase transitions 71, 143 (2000). http://doi.org/10.1080/01411590008224545
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 1.06
Times cited: 21
DOI: 10.1080/01411590008224545
|
|
|
“Natural titanite and malayite: structural investigations and the 500K anomaly”. Meyer HW, Bismayer U, Adiwidjaja G, Zhang M, Nistor L, Van Tendeloo G, Phase transitions 67, 27 (1998). http://doi.org/10.1080/01411599808219187
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 1.06
Times cited: 9
DOI: 10.1080/01411599808219187
|
|
|
“Laser induced phase transition in iron thin films”. Teodorescu VS, Mihailescu IN, Dinescu M, Chitica N, Nistor LC, van Landuyt J, Barborica A, Journal de physique: 3: applied physics, materials science, fluids, plasma and instrumentation 4, 127 (1994). http://doi.org/10.1051/jp4:1994427
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Times cited: 2
DOI: 10.1051/jp4:1994427
|
|
|
“P-type ZnO thin films grown by RF plasma beam assisted Pulsed Laser Deposition”. Epurescu G, Dinescu G, Moldovan A, Birjega R, Dipietrantonio F, Verona E, Verardi P, Nistor LC, Ghica C, Van Tendeloo G, Dinescu A, Superlattices and microstructures 42, 79 (2007). http://doi.org/10.1016/j.spmi.2007.04.072
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 2.123
Times cited: 19
DOI: 10.1016/j.spmi.2007.04.072
|
|
|
“In situ transmission electron microscopy study of the silicidation process in Co thin films on patterned (001) Si substrates”. Ghica C, Nistor L, Bender H, Steegen A, Lauwers A, Maex K, van Landuyt J, Journal of materials research 16, 701 (2001). http://doi.org/10.1557/JMR.2001.0121
Abstract: The results of an in situ transmission electron microscopy study of the formation of Co-silicides on patterned (001) Si substrates are discussed. It is shown that the results of the in situ heating experiments agreed very well with the data based on standard rapid thermal annealing experiments. Fast heating rates resulted in better definition of the silicide lines. Also, better lines were obtained for samples that received already a low-temperature ex situ anneal. A Ti cap layer gave rise to a higher degree of epitaxy in the CoSi2 silicide.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 1.673
Times cited: 4
DOI: 10.1557/JMR.2001.0121
|
|
|
“Incorporation and localization of substitutional Mn2+ ions in cubic ZnS quantum dots”. Nistor SV, Stefan M, Nistor LC, Goovaerts E, Van Tendeloo G, Physical review : B : condensed matter and materials physics 81, 035336 (2010). http://doi.org/10.1103/PhysRevB.81.035336
Abstract: Multifrequency electron paramagnetic resonance (EPR) and high resolution transmission electron microscopy (HRTEM) investigations were performed on small (2 nm) cubic ZnS nanocrystals (quantum dotsQDs) doped with 0.2% mol Mn2+, self-assembled into a mesoporous structure. The EPR data analysis shows that the substitutional Mn2+ ions are localized at Zn2+ sites subjected to a local axial lattice distortion, resulting in the observed zero-field-splitting parameter |D|=41×10−4 cm−1. The local distortion is attributed to the presence in the second shell of ligands of a stacking fault or twin, which alters the normal stacking sequence of the cubic structure. The HRTEM results confirm the presence of such extended planar defects in a large percentage of the investigated QDs, which makes possible the proposed substitutional Mn2+ impurity ions localization model. Based on these results it is suggested that the high doping levels of Mn2+ ions observed in cubic ZnS and possible in other II-VI semiconductor QDs prepared at low temperatures can be explained by the assistance of the extended lattice defects in the impurities incorporation.
Keywords: A1 Journal article; Nanostructured and organic optical and electronic materials (NANOrOPT); Electron microscopy for materials research (EMAT)
Impact Factor: 3.836
Times cited: 55
DOI: 10.1103/PhysRevB.81.035336
|
|
|
“Modulated structures in KAISi3O8: a study by high resolution electron microscopy and 29Si MAS-NMR spectroscopy”. Sanchez-Munoz L, Nistor L, Van Tendeloo G, Sanz J, Journal of electron microscopy 47, 17 (1998). http://doi.org/10.1093/oxfordjournals.jmicro.a023555
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 0.9
Times cited: 10
DOI: 10.1093/oxfordjournals.jmicro.a023555
|
|