“A potential method to correlate electrical properties and microstructure of a unique high-Tc superconducting Josephson junction”. Verbist K, Lebedev OI, Van Tendeloo G, Tafuri F, Granozio FM, Di Chiara A, Bender H, Applied physics letters 74, 1024 (1999). http://doi.org/10.1063/1.123443
Abstract: A method to correlate microstructure from cross-section transmission electron microscopy (TEM) investigations and transport properties of a single well characterized high-T-c artificial grain boundary junction is reported. A YBa2Cu3O7-delta 45 degrees twist junction exhibiting the typical phenomenology of high T-c Josephson weak links was employed. The TEM sample preparation is based on focused ion beam etching and allows to easily localize the electron transparent area on a microbridge. The reported technique opens clear perspectives in the determination of the microstructural origin of variations in Josephson junction properties, such as the spread in I-c and IcRN values and the presence of different transport regimes in nominally identical junctions. (C) 1999 American Institute of Physics. [S0003-6951(99)03404-X].
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 3.411
Times cited: 5
DOI: 10.1063/1.123443
|
“Preparation of nanocrystalline titania powder via aerosol pyrolysis of titanium tetrabutoxide”. Ahonen PP, Kauppinen EI, Joubert JC, Deschanvres JL, Van Tendeloo G, Journal of materials research 14, 3938 (1999). http://doi.org/10.1557/JMR.1999.0533
Abstract: Nanocrystalline titanium dioxide was prepared via aerosol pyrolysis of titanium alkoxide precursor at 200-580 degrees C in air and in nitrogen atmospheres. Powders were characterized by x-ray diffraction, thermogravimetric analysis, Brunauer-Emmett-Teller analysis, scanning electron microscopy, transmission electron microscopy, energy dispersive spectroscopy, x-ray fluorescence, Raman and infrared spectroscopy, and Berner-type low-pressure impactor. The anatase phase transition was initiated at 500 degrees C in nitrogen and at 580 degrees C in air. Under other conditions amorphous powders were observed and transformed to nanocrystalline TiO2 via thermal postannealing. In air, smooth and spherical particles with 2-4-mu m diameter were formed with an as-expected tendency to convert to rutile in the thermal postannealings. In nitrogen, a fraction of the titanium tetrabutoxide precursor evaporated and formed ultrafine particles via the gas-to-particle conversion. At 500 degrees C thermally stable anatase phase was formed in nitrogen. A specific surface area as high as 280 m(2) g(-1) was observed for an as-prepared powder.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 1.673
Times cited: 38
DOI: 10.1557/JMR.1999.0533
|
“Preparing polymer films doped with magnetic nanoparticles by spin-coating and melt-processing can induce an in-plane magnetic anisotropy”. Wouters J, Lebedev OI, Van Tendeloo G, Yamada H, Sato N, Vanacken J, Moshchalkov VV, Verbiest T, Valev VK, Journal of applied physics 109, 076105 (2011). http://doi.org/10.1063/1.3572048
Abstract: Faraday rotation has been used to investigate a series of polymer films doped with magnetic iron oxide nanoparticles. The films have been prepared by spin-coating and melt-processing. In each case, upon varying the angle of optical incidence on the films, an in-plane magnetic anisotropy is observed. The effect of such an anisotropy on the Faraday rotation as a function of the angle of optical incidence is verified by comparison with magnetically poled films. These results demonstrate that care should be taken upon analyzing the magnetic behavior of such films on account of the sample preparation techniques themselves being able to affect the magnetization.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 2.068
Times cited: 10
DOI: 10.1063/1.3572048
|
“Reconstruction of the La0.9Sr0.1MnO3-SrTiO3 interface by quantitative high-resolution electron microscopy”. Geuens P, Lebedev OI, Van Tendeloo G, Solid state communications 116, 643 (2000). http://doi.org/10.1016/S0038-1098(00)00411-7
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 1.554
Times cited: 2
DOI: 10.1016/S0038-1098(00)00411-7
|
“Relaxation phenomena at the metal-to-insulator transition in La0.8Sr0.2MnO3 single crystals”. Dominiczak M, Ruyter A, Limelette P, Monot-Laffez I, Giovannelli F, Rossell MD, Van Tendeloo G, Solid state communications 148, 340 (2008). http://doi.org/10.1016/j.ssc.2008.08.029
Abstract: The time dependence of the resistance RAC of a La0.8Sr0.2MnO3 single crystal has been investigated in the vicinity of the metal-to-insulator transition temperature. We used local probe microscopy to show the existence, at room temperature, of coexisting clusters of micrometer size. Our analysis shows that relaxation effects can be described with a simple exponential contribution using a random resistor-network, based on phase separation between insulating and metallic domains. Our results clearly prove the existence of a percolation threshold over which no percolation path exists. Moreover, these results highlight the significant role of the remanent magnetization.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 1.554
Times cited: 9
DOI: 10.1016/j.ssc.2008.08.029
|
“Resistive switching at manganite/manganite interfaces”. Kalkert C, Krisponeit J-O, Esseling M, Lebedev OI, Moshnyaga V, Damaschke B, Van Tendeloo G, Samwer K, Applied physics letters 99, 132512 (2011). http://doi.org/10.1063/1.3643425
Abstract: We report bipolar resistive switching between the interfaces of manganite nanocolumns. La0.7Sr0.3MnO3 films were prepared on Al2O3 substrates, where the films grow in nanocolumns from the substrate to the surface. Conductive atomic force microscopy directly detects that the resistive switching is located at the boundaries of the grains. Furthermore, mesoscopic transport measurements reveal a tunnel magnetoresistance. In combination with the resistive switching, this leads to a total of four different resistive states.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 3.411
Times cited: 10
DOI: 10.1063/1.3643425
|
“Reversible Li-intercalation through oxygen reactivity in Li-rich Li-Fe-Te oxide materials”. McCalla E, Prakash AS, Berg E, Saubanere M, Abakumov AM, Foix D, Klobes B, Sougrati MT, Rousse G, Lepoivre F, Mariyappan S, Doublet ML, Gonbeau D, Novak P, Van Tendeloo G, Hermann RP, Tarascon JM;, Journal of the electrochemical society 162, A1341 (2015). http://doi.org/10.1149/2.0991507jes
Abstract: Lithium-rich oxides are a promising class of positive electrode materials for next generation lithium-ion batteries, and oxygen plays a prominent role during electrochemical cycling either by forming peroxo-like species and/or by irreversibly forming oxygen gas during first charge. Here, we present Li-Fe-Te-O materials which show a tremendous amount of oxygen gas release. This oxygen release accounts for nearly all the capacity during the first charge and results in vacancies as seen by transmission electron microscopy. There is no oxidation of either metal during charge but significant changes in their environments. These changes are particularly extreme for tellurium. XRD and neutron powder diffraction both show limited Changes during cycling and no appreciable change in lattice parameters. A density functional theory study of this material is performed and demonstrates that the holes created on some of the oxygen atoms upon oxidation are partially stabilized through the formation of shorter O-O bonds, i.e. (O-2)(n-) species which on further delithiation show a spontaneous O-2 de-coordination from the cationic network and migration to the now empty lithium layer. The rate limiting step during charge is undoubtedly the diffusion of oxygen either out along the lithium layer or via columns of oxygen atoms. (C) 2015 The Electrochemical Society. All rights reserved.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 3.259
Times cited: 23
DOI: 10.1149/2.0991507jes
|
“The role of Al on Ohmic contact formation on n-type GaN and AlGaN/GaN”. van Daele B, Van Tendeloo G, Ruythooren W, Derluyn J, Leys M, Germain M, Applied physics letters 87, 061905 (2005). http://doi.org/10.1063/1.2008361
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 3.411
Times cited: 57
DOI: 10.1063/1.2008361
|
“Short-range order in phase segregation systems”. De Meulenaere P, Mommaert C, Van Tendeloo G, Solid state communications 102, 687 (1997). http://doi.org/10.1016/S0038-1098(97)00071-9
Abstract: Spin systems on an f.c.c.-lattice which exhibit phase segregation are studied by means of Monte Carlo simulations. Short-range order, both above and below the segregation temperature, is observed. Experimental evidence for short range order in Ti-V is provided by electron diffraction.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 1.554
DOI: 10.1016/S0038-1098(97)00071-9
|
“A-site ordering versus electronic inhomogeneity in colossally magnetoresistive manganite films”. Moshnyaga V, Sudheendra L, Lebedev OI, Koster SA, Gehrke K, Shapoval O, Belenchuk A, Damaschke B, Van Tendeloo G, Samwer K, Physical review letters 97, 107205 (2006). http://doi.org/10.1103/PhysRevLett.97.107205
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 8.462
Times cited: 43
DOI: 10.1103/PhysRevLett.97.107205
|
“Site-specific mapping of transition metal oxygen coordination in complex oxides”. Turner S, Egoavil R, Batuk M, Abakumov AA, Hadermann J, Verbeeck J, Van Tendeloo G, Applied physics letters 101, 241910 (2012). http://doi.org/10.1063/1.4770512
Abstract: We demonstrate site-specific mapping of the oxygen coordination number for transition metals in complex oxides using atomically resolved electron energy-loss spectroscopy in an aberration-corrected scanning transmission electron microscope. Pb2Sr2Bi2Fe6O16 contains iron with a constant Fe3+ valency in both octahedral and tetragonal pyramidal coordination and is selected to demonstrate the principle of site-specific coordination mapping. Analysis of the site-specific Fe-L2,3 data reveals distinct variations in the fine structure that are attributed to Fe in a six-fold (octahedron) or five-fold (distorted tetragonal pyramid) oxygen coordination. Using these variations, atomic resolution coordination maps are generated that are in excellent agreement with simulations.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 3.411
Times cited: 12
DOI: 10.1063/1.4770512
|
“The size and structure of Ag particles responsible for surface plasmon effects and luminescence in Ag homogeneously doped bulk glass”. Shestakov MV, Meledina M, Turner S, Tikhomirov VK, Verellen N, Rodríguez VD, Velázquez JJ, Van Tendeloo G, Moshchalkov VV, Journal of applied physics 114, 073102 (2013). http://doi.org/10.1063/1.4818830
Abstract: As-prepared and heat-treated oxyfluoride glasses, co-doped with Ag nanoclusters/nanoparticles, are prepared at 0.15 at. % Ag concentration. The as-prepared glass shows an absorption band in the UV/violet attributed to the presence of amorphous Ag nanoclusters with an average size of 1.1 nm. The luminescence spectra of the untreated glass can also be ascribed to these Ag nanoclusters. Upon heat-treatment, the clusters coalesce into Ag nanoparticles with an average size of 2.3 nm, and the glasses show an extra surface plasmon absorption band in the visible. These particles, however, cease to emit due to ascribing plasmonic properties of bulk silver.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 2.068
Times cited: 19
DOI: 10.1063/1.4818830
|
“Size distribution and magnetic behavior of lead inclusions in silicon single crystals”. Milants K, Verheyden J, Barancira T, Deweerd W, Pattyn H, Bukshpan S, Williamson DL, Vermeiren F, Van Tendeloo G, Vlekken C, Libbrecht S, van Haesendonck C, Journal of applied physics 81, 2148 (1997)
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 2.068
Times cited: 8
|
“Stabilization of the cubic phase of HfO2 by Y addition in films grown by metal organic chemical vapor deposition”. Rauwel E, Dubourdieu C, Holländer B, Rochat N, Ducroquet F, Rossell MD, Van Tendeloo G, Pelissier B, Applied physics letters 89, 012902 (2006). http://doi.org/10.1063/1.2216102
Abstract: Addition of yttrium in HfO(2) thin films prepared on silicon by metal organic chemical vapor deposition is investigated in a wide compositional range (2.0-99.5 at. %). The cubic structure of HfO(2) is stabilized for 6.5 at. %. The permittivity is maximum for yttrium content of 6.5-10 at. %; in this range, the effective permittivity, which results from the contribution of both the cubic phase and silicate phase, is of 22. These films exhibit low leakage current density (5x10(-7) A/cm(2) at -1 V for a 6.4 nm film). The cubic phase is stable upon postdeposition high temperature annealing at 900 degrees C under NH(3). (c) 2006 American Institute of Physics.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 3.411
Times cited: 78
DOI: 10.1063/1.2216102
|
“Statistical estimation of atomic positions from exit wave reconstruction with a precision in the picometer range”. Bals S, Van Aert S, Van Tendeloo G, Avila-Brande D, Physical review letters 96, 096106 (2006). http://doi.org/10.1103/PhysRevLett.96.096106
Abstract: The local structure of Bi4W2/3Mn1/3O8Cl is determined using quantitative transmission electron microscopy. The electron exit wave, which is closely related to the projected crystal potential, is reconstructed and used as a starting point for statistical parameter estimation. This method allows us to refine all atomic positions on a local scale, including those of the light atoms, with a precision in the picometer range. Using this method one is no longer restricted to the information limit of the electron microscope. Our results are in good agreement with x-ray powder diffraction data demonstrating the reliability of the method. Moreover, it will be shown that local effects can be interpreted using this approach.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 8.462
Times cited: 69
DOI: 10.1103/PhysRevLett.96.096106
|
“Strain relaxation and oxygen superstructure modulation in epitaxial Sr4Fe6O13\pm\delta films”. Santiso J, Pardo JA, Solis C, Garcia G, Figueras A, Rossell MD, Van Tendeloo G, Applied physics letters 86, 132105 (2005). http://doi.org/10.1063/1.1886264
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 3.411
Times cited: 5
DOI: 10.1063/1.1886264
|
“Structural defects and epitaxial rotation of C60 and C70 (111) films on GeS(001)”. Bernaerts D, Van Tendeloo G, Amelinckx S, Hevesi K, Gensterblum G, Yu LM, Pireaux JJ, Grey F, Bohr J, Journal of applied physics 80, 3310 (1996). http://doi.org/10.1063/1.363241
Abstract: A transmission electron microscopy study of epitaxial C-60 and C-70 films grown on a GeS (001) surface is presented. The relationship between the orientation of the substrate and the films and structural defects in the films, such as grain boundaries, unknown in bulk C-60 and C-70 crystals, are studied. Small misalignments of the overlayers with respect to the orientation of the substrate, so-called epitaxial rotations, exist mainly in C-70 films, but also sporadically in the C-60 overlayers. A simple symmetry model, previously used to predict the rotation of hexagonal overlayers on hexagonal substrates, is numerically tested and applied to the present situation. Some qualitative conclusions concerning the substrate-film interaction are deduced. (C) 1996 American Institute of Physics.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 2.183
Times cited: 6
DOI: 10.1063/1.363241
|
“Structural investigations of recently discovered high Tc superconductors”. Van Tendeloo G, Krekels T, Amelinckx S, Babu TGN, Greaves C, Hervieu M, Michel C, Raveau B, Microscopy research and technique 30, 102 (1995). http://doi.org/10.1002/jemt.1070300203
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 1.154
Times cited: 4
DOI: 10.1002/jemt.1070300203
|
“Structural phase transition at low temperature, corresponding to charge ordering in the CMR perovskites LN0.5A0.5MNO3”. Laffez P, Van Tendeloo G, Millange F, Caignaert V, Hervieu M, Raveau B, Materials research bulletin 31, 905 (1996). http://doi.org/10.1016/S0025-5408(96)00090-6
Abstract: The magneto resistive perovskites Nd0.5Sr0.5MnO3 and Pr0.5Sr0.41Ca0.09MnO3 undergo a transition from anti ferromagnetic insulator to ferromagnetic metal as function of temperature. The room temperature phase is orthorhombic with the space group Imma and the cell parameters a approximate to root 2a(p), b approximate to 2a(p), and c approximate to root 2a(p). A structural phase transition related to charge ordering accompanying the transition from ferromagnetic state to antiferromagnetic state has been evidenced by low temperature electron diffraction. This transition is reversible and a new superstructure, with a P-type orthorhombic cell. and lattice parameters parameters a approximate to 2 root 2a(p), b approximate to 2a(p), and c approximate to root 2a(p), is formed.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 2.288
Times cited: 25
DOI: 10.1016/S0025-5408(96)00090-6
|
“Structure and properties of artificial [(La0.7Sr0.3MnO3)m(SrTiO3)n]15 superlattices on (001)SrTiO3”. Lebedev OI, Verbeeck J, Van Tendeloo G, Dubourdieu C, Rosina M, Chaudouët P, Journal of applied physics 94, 7646 (2003). http://doi.org/10.1063/1.1628407
Abstract: Complex [(La0.7Sr0.3MnO3)(m)(SrTiO3)(n)] [(LSMO)(m)/(STO)(8)](15) superlattices with different layer thicknesses (m=5, 8, 12, 16, 32) have been prepared using pulsed liquid injection metalorganic chemical vapor deposition. Transmission electron microscopy and electron diffraction reveal a very clear and well-separated layer sequence. The remarkable microstructure, as well as the ferromagnetic transition temperature, depends on the LSMO layer thickness. Apart from a very clear layer sequence, electron microscopy shows evidence of a self-assembled nanostructure formation: SrMnO3 nanoinclusions and associated SrTiO3-SrMnO3 thin walls. A formation model and growth mechanism for the self-assembled structure is proposed, based on high resolution and energy filtered elemental imaging. (C) 2003 American Institute of Physics.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 2.068
Times cited: 22
DOI: 10.1063/1.1628407
|
“Structure and properties of the YBa2Cu3O7-x/LaAlO3 superlattices”. Lebedev OI, Hamet JF, Van Tendeloo G, Beaumont V, Raveau B, Journal of applied physics 90, 5261 (2001). http://doi.org/10.1063/1.1406963
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 2.068
Times cited: 13
DOI: 10.1063/1.1406963
|
“Structure of epitaxial Ca2Fe2O5 films deposited on different perovskite-type substrates”. Rossell MD, Lebedev OI, Van Tendeloo G, Hayashi N, Terashima T, Takano M, Journal of applied physics 95, 5145 (2004). http://doi.org/10.1063/1.1689003
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 2.068
Times cited: 16
DOI: 10.1063/1.1689003
|
“Structure of the hexagonal 16l perovskites Ba4Ca0.9Mn3.1O11.3 and Ba4Ca0.5Mn3Cu0.5O12-\delta by high-resolution electron microscopy”. Schuddinck W, Van Tendeloo G, Hervieu M, Floros N, Raveau B, Materials research bulletin 36, 2689 (2001). http://doi.org/10.1016/S0025-5408(01)00744-9
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 2.446
Times cited: 4
DOI: 10.1016/S0025-5408(01)00744-9
|
“The study of partially ordered 11/20 alloys by HREM”. De Meulenaere P, Van Tendeloo G, van Landuyt J, Microscopy research and technique 25, 169 (1993). http://doi.org/10.1002/jemt.1070250208
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 1.154
DOI: 10.1002/jemt.1070250208
|
“Substitution of mercury for thallium in the 2223 cuprate: the 130K superconductor Tl1.6Hg0.4Ba2Cu3O10-x”. Goutenoire F, Maignan A, Van Tendeloo G, Martin C, Michel C, Hervieu M, Raveau B, Solid state communications 90, 47 (1994)
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 1.897
Times cited: 16
|
“Superconducting single-phase Sr1-xLaxCuO2 thin films with improved crystallinity grown by pulsed laser deposition”. Leca V, Blank DHA, Rijnders G, Bals S, Van Tendeloo G, Applied physics letters 89 (2006). http://doi.org/10.1063/1.2339840
Abstract: Sr1-xLaxCuO2-delta (x=0.10-0.20) thin films exhibiting an oxygen-deficient 2 root 2a(p)x2 root a(p) x c structure (a(p) and c represent the cell parameters of the perovskite subcell) were epitaxially grown by means of pulsed laser deposition in low-pressure oxygen ambient. (001) KTaO3 and (001) SrTiO3 single crystals were used as substrates, with BaTiO3 as buffer layer. The Sr1-xLaxCuO2-delta films were oxidized during cooling down in order to yield the infinite-layer-type structure. By applying this method, high quality single-phase Sr1-xLaxCuO2 thin films could be obtained for 0.10 <= x <= 0.175 doping range. The films grown on BaTiO3/KTaO3 show superconductivity for 0.15 <= x <= 0.175 with optimum doping at x=0.15, in contrast with previously reported data. (c) 2006 American Institute of Physics.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 3.411
Times cited: 32
DOI: 10.1063/1.2339840
|
“Symmetry and electronic states of Mn2+ in ZnS nanowires with mixed hexagonal and cubic stacking”. Chen L, Kirilenko D, Stesmans A, Nguyen XS, Binnemans K, Goderis B, Vanacken J, Lebedev O, Van Tendeloo G, Moshchalkov VV, Applied physics letters 97, 041918 (2010). http://doi.org/10.1063/1.3475017
Abstract: Electron spin resonance and electronic spectroscopy techniques were used to study the symmetry and electronic structure of Mn2+ dopants in solvothermally synthesized ZnS nanowires. The average diameter of ∼ 5 nm leads to the observable quantum confinement effects in the photoluminescence excitation spectra. The results clearly demonstrate the three symmetry locations of Mn2+ incorporation. Together with the inferred Mn2+ center densities, these data indicate a much higher efficiency of Mn2+ substitution in the nanowire sample with about two times larger diameter.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 3.411
Times cited: 5
DOI: 10.1063/1.3475017
|
“Synthesis, structure and properties of layered bismuthates: (Ba,K)3Bi2O7 and (Ba,K)2BiO4”. Khasanova NR, Kovba ML, Putilin SN, Antipov EV, Lebedev OI, Van Tendeloo G, Solid state communications 122, 189 (2002). http://doi.org/10.1016/S0038-1098(02)00096-0
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 1.554
Times cited: 3
DOI: 10.1016/S0038-1098(02)00096-0
|
“Tailoring CuO nanostructures for enhanced photocatalytic property”. Liu J, Jin J, Deng Z, Huang SZ, Hu ZY, Wang L, Wang C, Chen LH, Li Y, Van Tendeloo G, Su BL;, Journal of colloid and interface science 384, 1 (2012). http://doi.org/10.1016/j.jcis.2012.06.044
Abstract: We report on one-pot synthesis of various morphologies of CuO nanostructures. PEG200 as a structure directing reagent under the synergism of alkalinity by hydrothermal method has been employed to tailor the morphology of CuO nanostructures. The CuO products have been characterized by XRD, SEM, and TEM. The morphologies of the CuO nanostructures can be tuned from 10 (nanoseeds, nanoribbons) to 2D (nanoleaves) and to 3D (shuttle-like, shrimp-like, and nanoflowers) by changing the volume of PEG200 and the alkalinity in the reaction system. At neutral and relatively low alkalinity (OH-/Cu2+ <= 3), the addition of PEG200 can strongly influence the morphologies of the CuO nanostructures. At high alkalinity (OH/Cu2+ >= 4), PEG200 has no influence on the morphology of the CuO nanostructure. The different morphologies of the CuO nanostructures have been used for the photodecomposition of the pollutant rhodamine B (RhB) in water. The photocatalytic activity has been correlated with the different nanostructures of CuO. The 10 CuO nanoribbons exhibit the best performance on the RhB photodecomposition because of the exposed high surface energy {-121} crystal plane. The photocatalytic results show that the high energy surface planes of the CuO nanostructures mostly affect the photocatalytic activity rather than the morphology of the CuO nanostructures. Our synthesis method also shows it is possible to control the morphologies of nanostructures in a simple way. (C) 2012 Elsevier Inc. All rights reserved.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 4.233
Times cited: 105
DOI: 10.1016/j.jcis.2012.06.044
|
“:Ba2.1Bi0.9(O, F)6.8-\delta: a new ordered anion-excess fluorite”. Prituzhalov VA, Abakumov AM, Ardashnikova EI, Dolgikh VA, Van Tendeloo G, Materials research bulletin 42, 861 (2007). http://doi.org/10.1016/j.materresbull.2006.08.023
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 2.446
Times cited: 4
DOI: 10.1016/j.materresbull.2006.08.023
|