Records |
Author |
Aghaei, M.; Lindner, H.; Bogaerts, A. |
Title |
Effect of a mass spectrometer interface on inductively coupled plasma characteristics : a computational study |
Type |
A1 Journal article |
Year |
2012 |
Publication |
Journal of analytical atomic spectrometry |
Abbreviated Journal |
J Anal Atom Spectrom |
Volume |
27 |
Issue |
4 |
Pages |
604-610 |
Keywords |
A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) |
Abstract |
An inductively coupled plasma connected to a mass spectrometer interface (sampling cone) is computationally investigated. Typical plasma characteristics, such as gas flow velocity, plasma temperature and electron density, are calculated in two dimensions (cylindrical symmetry) and compared with and without a mass spectrometer sampling interface. The results obtained from our model compare favorably with experimental data reported in the literature. A dramatic increase in the plasma velocity is reported in the region close to the interface. Furthermore, a cooled metal interface lowers the plasma temperature and electron density on the axial channel very close to the sampling cone but the corresponding values in the off axial regions are increased. Therefore, the effect of the interface strongly depends on the measurement position. It is shown that even a small shift from the actual position of the sampler leads to a considerable change of the results. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
London |
Editor |
|
Language |
|
Wos |
000301496700005 |
Publication Date |
2012-02-22 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0267-9477;1364-5544; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
3.379 |
Times cited |
18 |
Open Access |
|
Notes ![sorted by Notes field, ascending order (up)](img/sort_asc.gif) |
|
Approved |
Most recent IF: 3.379; 2012 IF: 3.155 |
Call Number |
UA @ lucian @ c:irua:97386 |
Serial |
791 |
Permanent link to this record |
|
|
|
Author |
Aghaei, M.; Lindner, H.; Bogaerts, A. |
Title |
The effect of the sampling cone position and diameter on the gas flow dynamics in an ICP |
Type |
A1 Journal article |
Year |
2013 |
Publication |
Journal of analytical atomic spectrometry |
Abbreviated Journal |
J Anal Atom Spectrom |
Volume |
28 |
Issue |
9 |
Pages |
1485-1492 |
Keywords |
A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) |
Abstract |
An inductively coupled plasma, connected to a sampling cone of a mass spectrometer, is computationally investigated. The effects of the sampler orifice diameter (ranging from 1 to 2 mm) and distance of the sampler cone from the load coil (ranging from 7 to 17 mm) are studied. An increase in sampler orifice diameter leads to a higher central plasma temperature at the place of the sampler, as well as more efficient gas transfer through the sampler, by reducing the interaction of the plasma gas with the sampling cone. However, the flow velocity at the sampler position is found to be independent of the sampler orifice diameter. Moreover, by changing the sampler orifice diameter, we can control whether only the central gas or also the auxiliary gas can exit through the sampler. Finally, with the increasing distance of the sampler from the load coil, the plasma temperature at the place of the sampler decreases slightly, which might also have consequences for the ion generation and transport through the sampling cone. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
London |
Editor |
|
Language |
|
Wos |
000322922300016 |
Publication Date |
2013-06-26 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0267-9477;1364-5544; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
3.379 |
Times cited |
14 |
Open Access |
|
Notes ![sorted by Notes field, ascending order (up)](img/sort_asc.gif) |
|
Approved |
Most recent IF: 3.379; 2013 IF: 3.396 |
Call Number |
UA @ lucian @ c:irua:109204 |
Serial |
848 |
Permanent link to this record |
|
|
|
Author |
Aghaei, M.; Lindner, H.; Bogaerts, A. |
Title |
Optimization of operating parameters for inductively coupled plasma mass spectrometry : a computational study |
Type |
A1 Journal article |
Year |
2012 |
Publication |
Spectrochimica acta: part B : atomic spectroscopy |
Abbreviated Journal |
Spectrochim Acta B |
Volume |
76 |
Issue |
|
Pages |
56-64 |
Keywords |
A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) |
Abstract |
An inductively coupled plasma, connected to a mass spectrometer interface, is computationally investigated. The effect of pressure behind the sampler, injector gas flow rate, auxiliary gas flow rate, and applied power is studied. There seems to be an optimum range of injector gas flow rate for each setup which guaranties the presence and also a proper length of the central channel in the torch. Moreover, our modeling results show that for any specific purpose, it is possible to control that either only the central gas flow passes through the sampler orifice or that it is accompanied by the auxiliary gas flow. It was also found that depending on geometry, the variation of outgoing gas flow rate is much less than the variation of the injector gas flow rate and this causes a slightly higher pressure inside the torch. The general effect of increasing the applied power is a rise in the plasma temperature, which results in a higher ionization in the coil region. However, the negative effect is reducing the length of the cool central channel which is important to transfer the sample substances to the sampler. Using a proper applied power can enhance the efficiency of the system. Indeed, by changing the gas path lines, the power can control which flow (i.e., only from injector gas or also from the auxiliary gas) goes to the sampler orifice. Finally, as also reported from experiments in literature, the pressure behind the sampler has no dramatic effect on the plasma characteristics. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Oxford |
Editor |
|
Language |
|
Wos |
000311008600008 |
Publication Date |
2012-06-23 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0584-8547; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
3.241 |
Times cited |
18 |
Open Access |
|
Notes ![sorted by Notes field, ascending order (up)](img/sort_asc.gif) |
|
Approved |
Most recent IF: 3.241; 2012 IF: 3.141 |
Call Number |
UA @ lucian @ c:irua:101356 |
Serial |
2488 |
Permanent link to this record |
|
|
|
Author |
Aghaei, M.; Lindner, H.; Bogaerts, A. |
Title |
Ion Clouds in the Inductively Coupled Plasma Torch: A Closer Look through Computations |
Type |
A1 Journal article |
Year |
2016 |
Publication |
Analytical chemistry |
Abbreviated Journal |
Anal Chem |
Volume |
88 |
Issue |
88 |
Pages |
8005-8018 |
Keywords |
A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) |
Abstract |
We have computationally investigated the introduction of copper elemental particles in an inductively coupled plasma torch connected to a sampling cone, including for the first time the ionization of the sample. The sample is inserted as liquid particles, which are followed inside the entire torch, i.e., from the injector inlet up to the ionization and reaching the sampler. The spatial position of the ion clouds inside the torch as well as detailed information on the copper species fluxes at the position of the sampler orifice and the exhausts of the torch are provided. The effect of on- and off-axis injection is studied. We clearly show that the ion clouds of on-axis injected material are located closer to the sampler with less radial diffusion. This guarantees a higher transport efficiency through the sampler cone. Moreover, our model reveals the optimum ranges of applied power and flow rates, which ensure the proper position of ion clouds inside the torch, i.e., close enough to the sampler to increase the fraction that can enter the mass spectrometer and with minimum loss of material toward the exhausts as well as a sufficiently high plasma temperature for efficient ionization. |
Address |
Research Group PLASMANT, Chemistry Department, University of Antwerp , Universiteitsplein 1, 2610 Antwerp, Belgium |
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
English |
Wos |
000381654800020 |
Publication Date |
2016-07-26 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0003-2700 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
6.32 |
Times cited |
9 |
Open Access |
|
Notes ![sorted by Notes field, ascending order (up)](img/sort_asc.gif) |
The authors gratefully acknowledge financial support from the Fonds voor Wetenschappelijk Onderzoek (FWO), Grant Number 6713. The computational work was carried out using the Turing HPC infrastructure at the CalcUA core facility of the Universiteit Antwerpen (UA), a division of the Flemish Supercomputer Center VSC, funded by the Hercules Foundation, the Flemish Government (department EWI), and the UA. |
Approved |
Most recent IF: 6.32 |
Call Number |
PLASMANT @ plasmant @ c:irua:135644 |
Serial |
4293 |
Permanent link to this record |