|
|
“Optimization of the amount of catalyst and reaction time in single wall nanotube production”. Horvath ZE, Biro LP, Van Tendeloo G, Tondeur C, Bister G, Pierard N, Fonseca A, Nagy JB, Diffusion and defect data : solid state data : part B : solid state phenomena 94, 271 (2003)
Abstract: The influence of the amount of catalyst and the reaction time on the quantity and quality of catalytically grown single wall carbon nanotubes (SWNT) was investigated. The aim was to optimize some of the SWNT growth parameters using TEM and HRTEM. The thickness of catalyst layer influences the synthesis of the nanotube because the gas composition can differ between top and bottom. Microscopic investigation of the grown SWNT samples showed that the thicker the catalyst layer the lower relative nanotube content, so the deeper parts of the catalyst layer are less effective: The optimum time for the reaction was found to be 10 minutes. This may be understood assuming that nanotube growth needs an initial incubation time while the activity of the catalyst decreases steadily until the nariotube growth stops.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
|
|
|
|
“Optimizing Er/Yb ratio and content in Er-Yb co-doped glass-ceramics for enhancement of the up- and down-conversion luminescence”. Tikhomirov VK, Rodríguez VD, Méndez-Ramos J, del- Castillo J, Kirilenko D, Van Tendeloo G, Moshchalkov VV, Solar energy materials and solar cells 100, 209 (2012). http://doi.org/10.1016/j.solmat.2012.01.019
Abstract: Er3+Yb3+ co-doped transparent glass-ceramics with varying Er/Yb content and ratio have been prepared. High quantum yields for up- and down-conversion luminescence by energy transfer from Yb3+ to Er3+ and from Er3+ to Yb3+, respectively, have been detected and optimized with respect to the Er/Yb content and ratio, and proposed in particular for up- and down-conversion of solar spectrum for enhancement of the efficiency of solar cells. The rise and decay kinetics for the population of the excited levels of Er3+ and Yb3+ have been studied and fit. Based on these experimental data, the mechanisms for the energy transfers have been suggested with emphasis on the optimized Er/Yb content and ratio for enhancement of the efficiency of the Er3+↔Yb3+ energy transfers.
Keywords: A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
Impact Factor: 4.784
Times cited: 66
DOI: 10.1016/j.solmat.2012.01.019
|
|
|
|
“Optimizing mesoscopic two-band superconductors for observation of fractional vortex states”. Piña JC, de Souza Silva CC, Milošević, MV, Physica: C : superconductivity 503, 48 (2014). http://doi.org/10.1016/j.physc.2014.04.017
Abstract: Using the two-component Ginzburg-Landau model, we investigate the effect of sample size and magnitude and homogeneity of external magnetic field on the stability of fractional vortex states in a mesoscopic two-band superconducting disk. We found that each fractional state has a preferable sample size, for which the range of applied field in which the state is stable is pronouncedly large. Vice versa, there exists an optimal magnitude of applied field for which a large range of possible sample radii will support the considered fractional state. Finally, we show that the stability of fractional states can be enhanced even further by magnetic nanostructuring of the sample, i.e. by suitably chosen geometrical parameters and magnetic moment of a ferromagnetic dot placed on top of the superconducting disk. (C) 2014 Elsevier B.V. All rights reserved.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 1.404
Times cited: 5
DOI: 10.1016/j.physc.2014.04.017
|
|
|
|
“Ordering and defects in BanTaxTiyO3n ternary oxides”. Nistor L, Van Tendeloo G, Amelinckx S, Shpanchenko RV, van Landuyt J, Electron Microscopy 1994, Vols 2a And 2b: Applications In Materials Sciences , 869 (1994)
Keywords: P1 Proceeding; Electron microscopy for materials research (EMAT)
|
|
|
|
“Ordering and phase transitions of charged particles in a classical finite two-dimensional system”. Bedanov VM, Peeters FM, Physical review : B : condensed matter and materials physics 49, 2667 (1994)
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 3.736
Times cited: 412
|
|
|
|
“Organic SIMS: the influence of time on the ion yield enhancement by silver and gold deposition”. Adriaensen L, Vangaever F, Gijbels R, Applied surface science 231/232, 256 (2004). http://doi.org/10.1016/j.apsusc.2004.03.031
Keywords: A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Impact Factor: 3.387
Times cited: 10
DOI: 10.1016/j.apsusc.2004.03.031
|
|
|
|
“Organische TOF-S-SIMS: gebruik van opgedampt Ag en Au voor de verhoging van secundaire ionenintensiteiten”. Adriaensen L, Vangaever F, Gijbels R, Chemie magazine , 10 (2004)
Keywords: A2 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
|
|
|
|
“Orientation fluctuations, diffuse scattering and orientational order in solid C60”. Michel KH, Copley JRD World Scientific, Singapore, page 381 (1996).
Keywords: H3 Book chapter; Condensed Matter Theory (CMT)
|
|
|
|
“Orientational charge density waves and the metal-insulator transition in polymerized KC60”. Verberck B, Nikolaev AV, Michel KH, AIP conference proceedings 723, 339 (2004)
Abstract: Polymerized KC60 undergoes a structural phase transition accompanied by a metal-insulator transition around 50 K. To explain the structural aspect, a mechanism involving small orientational deviations of the valence electron density on every C-60 monomer orientational charge density waves (OCDWs) – has already been proposed earlier. In the present work, we address the metal-insulator transition using the OCDW concept. We are inspired by the analogy between a polymer chain exhibiting an OCDW and a linear atomic chain undergoing a static lattice deformation doubling the unit cell: such a deformation implies a band gap at the zone boundary, yielding an insulating state (Peierls instability). Within our view, a similar mechanism occurs in polymerized KC60; the OCDW plays the role of the lattice deformation. We present tight-binding band structure calculations and conclude that the metal-insulator transition can indeed be explained using OCDWs, but that the threedimensionality of the crystal plays an unexpected key role.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
|
|
|
|
“Orientational disorder and order in C60-fullerite and in MC60-alkali metal fullerides”. Nikolaev AV, Michel KH, Copley JRD Plenum Press, New York, page 183 (1999).
Keywords: H3 Book chapter; Condensed Matter Theory (CMT)
|
|
|
|
“Orientational mode coupling, diffuse scattering, and the order-disorder phase transition in solid C60”. Michel KH, Copley JRD, Zeitschrift für Physik: B: condensed matter and quanta 103, 369 (1997)
Keywords: A3 Journal article; Condensed Matter Theory (CMT)
Times cited: 21
|
|
|
|
“The origin of diffuse intensity in electron diffraction patterns”. Van Tendeloo G, Amelinckx S, Phase transitions 67, 101 (1998). http://doi.org/10.1080/01411599808219190
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 1.06
Times cited: 17
DOI: 10.1080/01411599808219190
|
|
|
|
“Ortho II structure in ABa2Cu307-d compounds (A=Er, Nd, Pr, Sm, Yb), pp”. Krekels T, Zou H, Van Tendeloo G, Wagner D, Buchgeister M, Hosseini SM, Herzog P, Physica: C : superconductivity 196, 363 (1992)
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 0.942
Times cited: 52
|
|
|
|
“Oscillating sliding wear of mono- and multilayer ceramic coatings in air”. Huq MZ, Celis JP, Meneve J, Stals L, Schryvers D, Surface and coatings technology 113, 242 (1999). http://doi.org/10.1016/S0257-8972(99)00009-2
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 2.589
Times cited: 10
DOI: 10.1016/S0257-8972(99)00009-2
|
|
|
|
“Oscillator strength and sum rule for inter-subband transitions in a superlattice”. Peeters FM, Matulis A, Helm M, Fromherz T, Hilber W, Physical review : B : condensed matter and materials physics 48, 12008 (1993). http://doi.org/10.1103/PhysRevB.48.12008
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 3.736
Times cited: 28
DOI: 10.1103/PhysRevB.48.12008
|
|
|
|
“Oxide superconductors: electron microscopy”. Mitchell TE, Gronsky R, Van Tendeloo G Pergamon Press, Oxford, page 401 (1992).
Keywords: H3 Book chapter; Electron microscopy for materials research (EMAT)
|
|
|
|
“Oxygen exchange on nanocrystalline tin dioxide modified by palladium”. Frolov DD, Kotovshchikov YN, Morozov IV, Boltalin AI, Fedorova AA, Marikutsa AV, Rumyantseva MN, Gaskov AM, Sadovskaya EM, Abakumov AM, Journal of solid state chemistry 186, 1 (2012). http://doi.org/10.1016/j.jssc.2011.11.028
Abstract: Temperature-programmed oxygen isotopic exchange study was performed on nanocrystalline tin dioxide-based materials synthesized via sol-gel route and modified by palladium. Such materials are widely used as resistive gas sensors. The experiments were carried out in a flow-reactor up to complete isotopic substitution of oxygen. Substantial rates of isotopic exchange for SnO2 were observed from about 700 K. The distribution of isotopic molecules O-16(2). (OO)-O-16-O-18 and O-18(2) corresponds to simple dioxygen heteroexchange mechanism with single lattice oxygen atom. The modification of SnO2 by Pd introduced multiple heteroexchange mechanism with preliminary O-2 dissociation on the clusters surface. Spill-over of atomic oxygen from Pd to the surface of SnO2 and fast exchange with lattice oxygen result in more than 100% increase of apparent heteroexchange rate. The exchange on SnO2/Pd was shown to be a complex process involving partial deactivation of the catalytic centers at temperature higher than 750 K. (C) 2011 Elsevier Inc. All rights reserved.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 2.299
Times cited: 34
DOI: 10.1016/j.jssc.2011.11.028
|
|
|
|
“Oxygen ordering and critical temperature plateaus in ABa2Cu3O7-d (A=Er, Nd, Sm, Yb), pp”. Zou H, Krekels T, Van Tendeloo G, Wagener G, Buchgeister M, Hosseini SM, Kopitzki K, , 278 (1992)
Keywords: P3 Proceeding; Electron microscopy for materials research (EMAT)
|
|
|
|
“Padé, approximants for the groundstate energy of closed-shell quantum dots”. Gonzalez A, Partoens B, Peeters FM, Physical review : B : condensed matter and materials physics 56, 15740 (1997). http://doi.org/10.1103/PhysRevB.56.15740
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 3.836
Times cited: 18
DOI: 10.1103/PhysRevB.56.15740
|
|
|
|
“The paraelectric-ferroelectric phase transition of Bi4Ti3O12 studied by electron microscopy”. Nistor L, Van Tendeloo G, Amelinckx S, Phase transitions 59, 135 (1996)
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 0.954
Times cited: 6
|
|
|
|
“Parametric study by means of numerical modelling for a dielectric barrier discharge at atmospheric pressure in nitrogen”. Madani M, Bogaerts A, Gijbels R, Vangeneugden D, , 49 (2004)
Keywords: P3 Proceeding; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
|
|
|
|
“Particle-in-cell/Monte Carlo collisions treatment of an Ar/O2 magnetron discharge used for the reactive sputter deposition of TiOx films”. Bultinck E, Bogaerts A, New journal of physics 11, 103010 (2009). http://doi.org/10.1088/1367-2630/11/10/103010
Abstract: The physical processes in an Ar/O2 magnetron discharge used for the reactive sputter deposition of TiOx thin films were simulated with a 2d3v particle-in-cell/Monte Carlo collisions (PIC/MCC) model. The plasma species taken into account are electrons, Ar+ ions, fast Arf atoms, metastable Arm* atoms, Ti+ ions, Ti atoms, O+ ions, O2+ ions, O− ions and O atoms. This model accounts for plasmatarget interactions, such as secondary electron emission and target sputtering, and the effects of target poisoning. Furthermore, the deposition process is described by an analytical surface model. The influence of the O2/Ar gas ratio on the plasma potential and on the species densities and fluxes is investigated. Among others, it is shown that a higher O2 pressure causes the region of positive plasma potential and the O− density to be more spread, and the latter to decrease. On the other hand, the deposition rates of Ti and O are not much affected by the O2/Ar proportion. Indeed, the predicted stoichiometry of the deposited TiOx film approaches x=2 for nearly all the investigated O2/Ar proportions.
Keywords: A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Impact Factor: 3.786
Times cited: 24
DOI: 10.1088/1367-2630/11/10/103010
|
|
|
|
“Particle-in-cell Monte Carlo modeling of Langmuir probes in an Ar plasma”. Cenian A, Chernukho A, Bogaerts A, Gijbels R, Leys C, Journal of applied physics 97, 123310 (2005). http://doi.org/10.1063/1.1938275
Keywords: A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Impact Factor: 2.068
Times cited: 18
DOI: 10.1063/1.1938275
|
|
|
|
“Particle-in-cell/Monte Carlo simulation of a capacitively coupled radio frequency Ar/Cf4 discharge: effect of gas composition”. Georgieva V, Bogaerts A, Gijbels R, Journal of applied physics 93, 2369 (2003). http://doi.org/10.1063/1.1542920
Keywords: A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Impact Factor: 2.068
Times cited: 57
DOI: 10.1063/1.1542920
|
|
|
|
“Particle-in-cell/Monte Carlo simulations of a low-pressure capacitively coupled radio-frequency discharge: effect of adding H2 to an Ar discharge”. Neyts E, Yan M, Bogaerts A, Gijbels R, Journal of applied physics 93, 5025 (2003). http://doi.org/10.1063/1.1563820
Keywords: A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Impact Factor: 2.068
Times cited: 15
DOI: 10.1063/1.1563820
|
|
|
|
“Particle layering in the ceramic-metal thin film Pt-Al2O3”. Gibaud A, Hazra S, Sella C, Laffez P, Désert A, Naudon A, Van Tendeloo G, Physical review : B : condensed matter and materials physics 63, 193407 (2001). http://doi.org/10.1103/PhysRevB.63.193407
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 3.836
Times cited: 25
DOI: 10.1103/PhysRevB.63.193407
|
|
|
|
“A peculiar diffraction effect in FCC crystals of C60”. Amelinckx S, van Heurck C, van Dyck D, Van Tendeloo G, Physica status solidi: A: applied research 131, 589 (1992). http://doi.org/10.1002/pssa.2211310231
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT); Vision lab
Times cited: 13
DOI: 10.1002/pssa.2211310231
|
|
|
|
“Phase boundaries of superconducting mesoscopic square loops”. Fomin VM, Misko VR, Devreese JT, Moshchalkov VV, 249/251, 476 (1998)
Keywords: A1 Journal article; Electron Microscopy for Materials Science (EMAT);
|
|
|
|
“Phase boundaries of superconducting mesoscopic square loops”. Fomin VM, Misko VR, Devreese JT, Moshchalkov VV, 12th International Conference on the Electronic Properties of Two-Dimensional Systems (EP2DS), Tokyo, 835 (1997)
Keywords: A1 Journal article; Electron Microscopy for Materials Science (EMAT);
|
|
|
|
“Phase competition between Y2BaCuO5 and Y2O3 precipitates in Y-rich YBCO thin films”. Scotti di Uccio U, Miletto Granozio F, di Chiara A, Tafuri F, Lebedev OI, Verbist K, Van Tendeloo G, Physica: C : superconductivity 321, 162 (1999)
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 1.404
Times cited: 17
|
|
