“Chemical characterization and multivariate analysis of atmospheric PM2.5 particles”. Ravindra K, Stranger M, Van Grieken R, Journal of atmospheric chemistry 59, 199 (2008). http://doi.org/10.1007/S10874-008-9102-5
Abstract: The new European Council Directive (PE-CONS 3696/07) frames the inhalable (PM10) and fine particles (PM2.5) on priority to chemically characterize these fractions in order to understand their possible relation with health effects. Considering this, PM2.5 was collected during four different seasons to evaluate the relative abundance of bulk elements (Cl, S, Si, Al, Br, Cu, Fe, Ti, Ca, K, Pb, Zn, Ni, Mn, Cr and V) and water soluble ions (F−, Cl−, NO2 −, NO3 −, SO4 2−, Na+, NH4 +, Ca2+ and Mg2+) over Menen, a Belgian city near the French border. The air quality over Menen is influenced by industrialized regions on both sides of the border. The most abundant ionic species were NO3 −, SO4 2− and NH4 +, and they showed distinct seasonal variation. The elevated levels of NO3 − during spring and summer were found to be related to the larger availability of the NOx precursor. The various elemental species analyzed were distinguished into crustal and anthropogenic source categories. The dominating elements were S and Cl in the PM2.5 particles. The anthropogenic fraction (e.g. Zn, Pb, and Cu) shows a more scattered abundance. Furthermore, the ions and elemental data were also processed using principal component analysis and cluster analysis to identify their sources and chemistry. These approach identifies anthropogenic (traffic and industrial) emissions as a major source for fine particles. The variations in the natural/anthropogenic fractions of PM2.5 were also found to be a function of meteorological conditions as well as of long-range transport of air masses from the industrialized regions of the continent.
Keywords: A1 Journal article; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation)
DOI: 10.1007/S10874-008-9102-5
|
“Ground state and normal-mode spectra of a two-dimensional system of dipole particles confined in a parabolic trap”. Munarin FF, Ferreira WP, Farias GA, Peeters FM, Physical review : E : statistical, nonlinear, and soft matter physics 78, 031405 (2008). http://doi.org/10.1103/PhysRevE.78.031405
Abstract: The ordered configurations of a monolayer of interacting magnetic dipoles confined in a circular parabolic potential are investigated as a function of the dipole moment of the particles. Despite the circular confinement, we find very asymmetric ordered structures like chains and Y-shaped configurations when a magnetic field is applied parallel to the plane of the particles. The normal-mode spectrum of the particles and its dependence on the magnetic field and the strength of the dipole moment of the particles are studied. The vibrational and rotational modes of the spectrum, which are associated with the stability of the system, are investigated in detail. The number of particles is varied and we found different ordering of the particles for different values of the dipole moment and the magnetic field. A ring structure with a large number of particles is observed for high values of the dipole moment of the particles.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 2.366
Times cited: 5
DOI: 10.1103/PhysRevE.78.031405
|
“Resonant tunneling in graphene microstructures”. Milton Pereira J, Vasilopoulos P, Peeters FM, Microelectronics journal 39, 534 (2008). http://doi.org/10.1016/j.mejo.2007.07.099
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 1.163
Times cited: 9
DOI: 10.1016/j.mejo.2007.07.099
|
“Tuning of the optical properties of (11k) grown InAs quantum dots by the capping layer”. Mlinar V, Peeters FM, Microelectronics journal 39, 359 (2008). http://doi.org/10.1016/j.mejo.2007.07.052
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 1.163
DOI: 10.1016/j.mejo.2007.07.052
|
“Complementary analysis of historical glass by scanning electron microscopy with energy dispersive X-ray spectroscopy and laser ablation inductiveley coupled plasma mass spectrometry”. Wagner B, Nowak A, Bulska E, Kunicki-Goldfinger J, Schalm O, Janssens K, schalm, Microchimica acta 162, 415 (2008). http://doi.org/10.1007/S00604-007-0835-7
Keywords: A1 Journal article; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation)
Times cited: 28
DOI: 10.1007/S00604-007-0835-7
|
“Model-based quantification of EELS: is standardless quantification possible?”.Verbeeck J, Bertoni G, Microchimica acta 161, 439 (2008). http://doi.org/10.1007/s00604-008-0948-7
Abstract: Electron energy loss spectroscopy (EELS) is an ideal tool to obtain chemical information from nanoscale volumes. Quantification of the experimental spectra however has prevented for a long time access to the available information in a reliable and reproducible way. We present recent advances in model-based quantification of EELS spectra and show that we obtain the best possible precision for a given dataset, as well as remarkably good accuracies when applied to three different materials. The results are shown to be far superior over conventional quantification techniques and could hold a promise for standardless quantification of EELS spectra.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 4.58
Times cited: 5
DOI: 10.1007/s00604-008-0948-7
|
“Modern developments and applications in microbeam analysis: proceedings of the 10th Workshop of the European Microbeam Analysis Society (EMAS), Antwerp, Belgium, May 6-10, 2007”. Van 't dack L, Gijbels R, Walker CT, Microchimica acta 161, 285 (2008). http://doi.org/10.1007/s00604-008-0958-5
Keywords: Editorial; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Impact Factor: 4.58
Times cited: 1
DOI: 10.1007/s00604-008-0958-5
|
“Application of EPMA and XRF for the investigation of particulate pollutants in the field of cultural heritage”. Kontozova-Deutsch V, Deutsch F, Godoi RHM, Spolnik Z, Wei W, Van Grieken R, Microchimica acta 161, 465 (2008). http://doi.org/10.1007/S00604-007-0917-6
Keywords: A1 Journal article; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation)
DOI: 10.1007/S00604-007-0917-6
|
“Investigation of gaseous and particulate air pollutants at the Basilica Saint-Urbain in Troyes, related to the preservation of the medieval stained glass windows”. Kontozova-Deutsch V, Godoi RHM, Worobiec A, Spolnik Z, Krata A, Deutsch F, Van Grieken R, Microchimica acta 162, 425 (2008). http://doi.org/10.1007/S00604-007-0930-9
Keywords: A1 Journal article; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation); Laboratory Experimental Medicine and Pediatrics (LEMP)
DOI: 10.1007/S00604-007-0930-9
|
“Modelling concentrations of airborne primary and secondary PM10 and PM2.5 with the BelEUROS-model in Belgium”. Deutsch F, Vankerkom J, Janssen L, Janssen S, Bencs L, Van Grieken R, Fierens F, Dumont G, Mensink C, Ecological modelling 217, 230 (2008). http://doi.org/10.1016/J.ECOLMODEL.2008.06.003
Abstract: The Eulerian Chemistry-Transport Model BelEUROS was used to calculate the concentrations of airborne PM10 and PM2.5 over Europe. Both primary as well as secondary particulate matter in the respirable size-range was taken into account. Especially PM2.5 aerosols are often formed in the atmosphere from gaseous precursor compounds. Comprehensive computer codes for the calculation of gas phase chemical reactions and thermodynamic equilibria between compounds in the gas-phase and the particulate phase had been implemented into the BelEUROS-model. Calculated concentrations of PM10 and PM2.5 are compared to observations, including both the spatial and daily, temporal distribution of particulate matter in Belgium for certain monitoring locations and periods. The concentrations of the secondary compounds ammonium, nitrate and sulfate have also been compared to observed values. BeIEUROS was found to reproduce the observed concentrations rather well. The model was applied to assess the contribution of emissions derived from the sector agriculture in Flanders, the northern part of Belgium, to PM10- and PM2.5-concentrations. The results demonstrate the importance of ammonia emissions in the formation of secondary particulate matter. Hence, future European emission abatement policy should consider more the role of ammonia in the formation of secondary particles
Keywords: A1 Journal article; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation)
DOI: 10.1016/J.ECOLMODEL.2008.06.003
|
“SnIV-containing layered double hydroxides as precursors for nano-sized ZnO/SnO2 photocatalysts”. Seftel EM, Popovici E, Mertens M, Stefaniak EA, Van Grieken R, Cool P, Vansant EF, Applied catalysis : B : environmental 84, 699 (2008). http://doi.org/10.1016/J.APCATB.2008.06.006
Abstract: Sn4+-containing LDH was prepared using the co-precipitation method at constant pH, and characterized using X-ray diffraction, UVvis diffuse reflectance spectroscopy and TG/DTG methods. The obtained product was further exposed to different thermal treatments in order to obtain nano-sized coupled ZnO/SnO2 systems with enhanced photocatalytic performances than the ones obtained by mixing the two semiconductor oxides. The formation of a well-defined ZnO/SnO2 system and the crystallite size, fully investigated using XRD, micro-Raman scattering and UVvis DR techniques, were found to be influenced by the nature of the precursors and the calcination temperature. The photocatalytic activity of the ZnO/SnO2 systems, evaluated for the photodegradation of methyl orange (MO) dye, was studied as a function of the initial pH, catalyst loading and the calcination temperature. The metal dispersion supplied by layered structures proved to be an advantage when preparing coupled ZnO/SnO2 systems, the photocatalytic activity being 2.3 times higher comparing with the physical mixtures performances. The maximum photocatalytic activity of the coupled ZnO/SnO2 system having a layered precursor was observed when using neutral pH, at a catalyst loading of 1 g/L calcined at 600 °C for 4 h.
Keywords: A1 Journal article; Laboratory of adsorption and catalysis (LADCA); AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation)
DOI: 10.1016/J.APCATB.2008.06.006
|
“Synthesis of few-layer graphene via microwave plasma-enhanced chemical vapour deposition”. Malesevic A, Vitchev R, Schouteden K, Volodin A, Zhang L, Van Tendeloo G, Vanhulsel A, van Haesendonck C, Nanotechnology 19, 305604 (2008). http://doi.org/10.1088/0957-4484/19/30/305604
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 3.44
Times cited: 309
DOI: 10.1088/0957-4484/19/30/305604
|
“Inhable particulate matter from lime industries: chemical composition and deposition in human respiratory tract”. Godoi RHM, Braga DM, Makarovska Y, Alfoldy B, Carvalho Filho MAS, Van Grieken R, Godoi AFL, Atmospheric environment : an international journal 42, 7027 (2008). http://doi.org/10.1016/J.ATMOSENV.2008.07.002
Abstract: Air pollution caused by the lime production industry has become a serious problem with potential effects to human health, especially in developing countries. Colombo is a city included in the Metropolitan Region of Curitiba (capital of Parana State) in South Brazil. In Colombo city, a correlation has been shown between the lime production and the number of persons who need respiratory treatment in a local hospital, indicating that the lime industry can cause deleterious health effects in the exposed workers and population. This research was conducted to deal firstly with the characterization of the size distribution and chemical compositions of particles emitted from lime manufacturing and subsequently to assess the deposition rate of inhaled dolomitic lime aerosol particles in the human respiratory tract. The elemental chemical composition and particle size of individual atmospheric particles was quantitatively elucidated, including low-Z components like C, N and 0, as well as higher-Z elements, using automated electron probe microanalysis. Information concerning the bulk composition is provided by energy-dispersive X-ray detection. The majority of the respirable particulate matter identified was composed of aluminosilicates, Ca-Mg oxides, carbon-rich particles, mixtures of organic particles and Ca-Mg carbonates, soot and biogenic particles. In view of the chemical composition and size distribution of the aerosol particles, local deposition efficiencies in the human respiratory system were calculated, revealing the deposition of CaO center dot MgO at extrathoracic, tracheobronchial and pulmonary levels. The results of this study offer evidence to the threat of the fine and coarse particles emitted from dolomite lime manufacturing, allowing policy-makers to better focus their mitigation strategies in an effective way, as well as to the dolomite producers for the purpose of designing and/or implementing improved emission controls.
Keywords: A1 Journal article; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation)
DOI: 10.1016/J.ATMOSENV.2008.07.002
|
“Synthesis and characterization of oxygen-deficient oxides BaCo1-xYxO3-y' x = 0.15, 0.25 and 0.33, with the perovskite structure”. Lomakov MV, Istomin SY, Abakumov AM, Van Tendeloo G, Antipov EV, Solid state ionics 179, 1885 (2008). http://doi.org/10.1016/j.ssi.2008.05.004
Abstract: Oxygen-deficient complex cobalt oxides BaCo1 − xYxO3 − y, = 0.15, 0.25 and 0.33, with a cubic perovskite structure have been synthesized in air at 1100 °C using a citrate route. Cation composition of the compounds was confirmed by energy-dispersed X-ray (EDX) microanalysis while oxygen content was determined by iodometric titration. An electron diffraction (ED) study of the x = 0.25 and 0.33 compositions show the presence of a diffuse intensity, indicating possible short-range ordering of the B cations. It was found that the treatment of BaCo0.75Y0.25O2.55 in a humid atmosphere leads to the absorption of water vapour at the first stage. Oxygen permeation studies of the ceramic membranes of BaCo0.75Y0.25O2.55 and BaCo0.67Y0.33O2.55 with variable thickness showed high oxygen fluxes of 0.170.32 µmol/cm2/s at 950 °C.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 2.354
Times cited: 9
DOI: 10.1016/j.ssi.2008.05.004
|
“Microstructure and high temperature transport properties of high quality epitaxial SrFeO3-\delta films”. Solís C, Rossell MD, Garcia G, Figueras A, Van Tendeloo G, Santiso J, Solid state ionics 179, 1996 (2008). http://doi.org/10.1016/j.ssi.2008.06.004
Abstract: We report the high temperature electronic transport properties of SrFeO3 − ä epitaxial thin films obtained by pulsed laser deposition on NdGaO3(110) substrates. The films show total conductivity higher than the bulk material and apparent activation energy of about 0.12 eV in O2, lower than reported values for SrFeO3 − ä films. The conductivity dependence with oxygen partial pressure shows a power dependence with an exponent close to + 1/4, in agreement with expected point defect equilibrium. For a given oxygen partial pressure, the temperature coefficient of resistance (TCR) shows a low positive value of about 1.52.5 10− 3 K− 1, which is still suitable for resistive oxygen sensing applications. The transport properties of the films are discussed in view of their particular microstructure.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 2.354
Times cited: 10
DOI: 10.1016/j.ssi.2008.06.004
|
“Carbon nanotube TiO2 hybrid films for detecting traces of O2”. Llobet E, Espinosa EH, Sotter E, Ionescu R, Vilanova X, Torres J, Felten A, Pireaux JJ, Ke X, Van Tendeloo G, Renaux F, Paint Y, Hecq M, Bittencourt C;, Nanotechnology 19, 375501 (2008). http://doi.org/10.1088/0957-4484/19/37/375501
Abstract: Hybrid titania films have been prepared using an adapted sol-gel method for obtaining well-dispersed hydrogen plasma-treated multiwall carbon nanotubes in either pure titania or Nb-doped titania. The drop-coating method has been used to fabricate resistive oxygen sensors based on titania or on titania and carbon nanotube hybrids. Morphology and composition studies have revealed that the dispersion of low amounts of carbon nanotubes within the titania matrix does not significantly alter its crystallization behaviour. The gas sensitivity studies performed on the different samples have shown that the hybrid layers based on titania and carbon nanotubes possess an unprecedented responsiveness towards oxygen (i.e. more than four times higher than that shown by optimized Nb-doped TiO(2) films). Furthermore, hybrid sensors containing carbon nanotubes respond at significantly lower operating temperatures than their non-hybrid counterparts. These new hybrid sensors show a strong potential for monitoring traces of oxygen (i.e. <= 10 ppm) in a flow of CO(2), which is of interest for the beverage industry.
Keywords: A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
Impact Factor: 3.44
Times cited: 48
DOI: 10.1088/0957-4484/19/37/375501
|
“Surface enhanced Raman scattering of silver sensitized cobalt nanoparticles in metaldielectric nanocomposites”. Margueritat J, Gonzalo J, Afonso CN, Hörmann U, Van Tendeloo G, Mlayah A, Murray DB, Saviot L, Zhou Y, Hong MH, Luk'yanchuk BS, Nanotechnology 19, 375701 (2008). http://doi.org/10.1088/0957-4484/19/37/375701
Abstract: We report the preparation of a new type of nanocomposite containing cobalt and silver nanoparticles organized in parallel layers with a well controlled separation. This arrangement allows the observation of an enhanced low-frequency Raman signal at the vibration frequency of cobalt nanoparticles excited through the surface plasmons of silver nanoparticles. Numerical simulations of the electric field confirm the emergence of hot spots when the separation between silver and cobalt nanoparticles is small enough.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 3.44
Times cited: 11
DOI: 10.1088/0957-4484/19/37/375701
|
“Manipulation of two-electron states by the electric field in stacked self-assembled dots”. Nowak MP, Szafran B, Peeters FM, Journal of physics : condensed matter 20, 395225 (2008). http://doi.org/10.1088/0953-8984/20/39/395225
Abstract: A pair of electrons in vertically stacked self-assembled quantum dots is studied and the singlettriplet energy splitting is calculated in an external electric field using the configuration-interaction method. We show that for double quantum dots the dependence of the singlet energy levels on the electric field involves multiple avoided crossings of three energy levels. The exchange interaction, i.e., the energy difference of the lowest triplet and lowest singlet states, can be tuned by an electric field in a wide range of several tens of meV. For electric fields exceeding a threshold value the exchange interaction becomes a linear function of the field when the two electrons in the singlet state start to occupy the same dot. We also consider non-symmetric confinement, non-perfectly aligned dots, in horizontal as well as vertical field orientation. In a stack of three vertically coupled dots the depth of the confinement in the central dot can be used to enhance the exchange interaction. For a deeper central dot the dependence of the exchange interaction on the electric field is anomalousit initially decreases when the field is applied in both directions parallel and antiparallel to the axis of the stack. Such a behavior is never observed for a pair of quantum dots.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 2.649
Times cited: 5
DOI: 10.1088/0953-8984/20/39/395225
|
“Andreev-type states induced by quantum confinement”. Shanenko AA, Croitoru MD, Mints RG, Peeters FM, Journal of Surface Investigation. X-ray, Synchrotron and Neutron Techniques 2, 611 (2008). http://doi.org/10.1134/S1027451008040216
Abstract: The properties of a clean superconductor with nanoscale dimensions are governed by quantum confinement of the electrons. This results in a spatially inhomogeneous superconducting condensate and in the formation of new Andreev-type quasiparticle states. These states are mainly located beyond regions where the superconducting condensate is enhanced. A numerical self-consistent solution of the Bogoliubov-de Gennes equations for a cylindrical metallic nanowire shows that these new Andreev-type states decrease the ratio of the energy gap to the critical temperature.
Keywords: A1 Journal article; Condensed Matter Theory (CMT); Electron microscopy for materials research (EMAT)
Times cited: 1
DOI: 10.1134/S1027451008040216
|
“Dislocations and plasticity of experimentally deformed coesite”. Idrissi H, Cordier P, Jacob D, Walte N, European journal of mineralogy 20, 665 (2008). http://doi.org/10.1127/0935-1221/2008/0020-1849
Abstract: Dislocation microstructures have been characterized by transmission electron microscopy in polycrystalline coesite deformed experimentally at 4 GPa, 1200 degrees C. Burgers vectors have been determined by large-angle convergent-beam electron diffraction. Sample orientation was assisted by precession electron diffraction to overcome difficulties arising from pseudo-hexagonal symmetry. The results are explained by using a pseudo-hexagonal setting. We found that most dislocations observed are of the 1/3 < 2 (1) over bar(1) over bar0 > type. No clear glide plane was identified, suggesting that climb is activated under these conditions. This conclusion is supported by the observation of numerous subgrain boundaries. We have also observed some [00011 dislocations. Finally, the C12/cl space group to which coesite belongs being centred, an additional slip system is observed: 1/6[(1) over bar2 (1) over bar3](01 (1) over bar1) (1/2[(1) over bar 10](110) in the monoclinic setting).
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 1.362
Times cited: 5
DOI: 10.1127/0935-1221/2008/0020-1849
|
“The dominant role of impurities in the composition of high pressure noble gas plasmas”. Martens T, Bogaerts A, Brok WJM, van Dijk J, Applied physics letters 92, 041504 (2008). http://doi.org/10.1063/1.2839613
Keywords: A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Impact Factor: 3.411
Times cited: 115
DOI: 10.1063/1.2839613
|
“Electron-vortex separation in quantum dots”. Anisimovas E, Tavernier MB, Peeters FM, Physical review : B : condensed matter and materials physics 77, 045327 (2008). http://doi.org/10.1103/PhysRevB.77.045327
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 3.836
Times cited: 3
DOI: 10.1103/PhysRevB.77.045327
|
“Electronic states above a helium film suspended on a ring-shaped substrate”. Ramos ACA, Chaves A, Farias GA, Peeters FM, Physical review : B : condensed matter and materials physics 77, 045415 (2008). http://doi.org/10.1103/PhysRevB.77.045415
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 3.836
Times cited: 4
DOI: 10.1103/PhysRevB.77.045415
|
“The extracellular matrix protein 1: its molecular interaction and implication in tumor progression”. Sercu S, Zhang L, Merregaert J, Cancer investigation 26, 375 (2008). http://doi.org/10.1080/07357900701788148
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 2.007
Times cited: 41
DOI: 10.1080/07357900701788148
|
“Functionalization of MWCNTs with atomic nitrogen : electronic structure”. Ruelle B, Felten A, Ghijsen J, Drube W, Johnson RL, Liang D, Erni R, Van Tendeloo G, Dubois P, Hecq M, Bittencourt C;, Journal of physics: D: applied physics 41, 045202 (2008). http://doi.org/10.1088/0022-3727/41/4/045202
Abstract: The changes induced by exposing multi-walled carbon nanotubes (CNTs) to atomic nitrogen were analysed by high-resolution transmission electron microscopy (HRTEM), x-ray and ultraviolet photoelectron spectroscopy. It was found that the atomic nitrogen generated by a microwave plasma effectively grafts chemical groups onto the CNT surface altering the density of valence electronic states. HRTEM showed that the exposure to atomic nitrogen does not significantly damage the CNT surface.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 2.588
Times cited: 16
DOI: 10.1088/0022-3727/41/4/045202
|
“General 2D Schrödinger-Poisson solver with open boundary conditions for nano-scale CMOS transistors”. Pourghaderi MA, Magnus W, Sorée B, de Meyer K, Meuris M, Heyns M, Journal of computational electronics 7, 475 (2008). http://doi.org/10.1007/s10825-008-0257-8
Abstract: Employing the quantum transmitting boundary (QTB) method, we have developed a two-dimensional Schrödinger-Poisson solver in order to investigate quantum transport in nano-scale CMOS transistors subjected to open boundary conditions. In this paper we briefly describe the building blocks of the solver that was originally written to model silicon devices. Next, we explain how to extend the code to semiconducting materials such as germanium, having conduction bands with energy ellipsoids that are neither parallel nor perpendicular to the channel interfaces or even to each other. The latter introduces mixed derivatives in the 2D effective mass equation, thereby heavily complicating the implementation of open boundary conditions. We present a generalized quantum transmitting boundary method that mainly leans on the completeness of the eigenstates of the effective mass equation. Finally, we propose a new algorithm to calculate the chemical potentials of the source and drain reservoirs, taking into account their mutual interaction at high drain voltages. As an illustration, we present the potential and carrier density profiles obtained for a (111) Ge NMOS transistor as well as the ballistic current characteristics.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 1.526
Times cited: 3
DOI: 10.1007/s10825-008-0257-8
|
“Local structure of perovskite-based “Pb2Fe2O5””. Hadermann J, Abakumov AM, Nikolaev IV, Antipov EV, Van Tendeloo G, Solid state sciences 10, 382 (2008). http://doi.org/10.1016/j.solidstatesciences.2007.12.008
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 1.811
Times cited: 29
DOI: 10.1016/j.solidstatesciences.2007.12.008
|
“Magnetic field dependence of the many-electron statis in a magnetic quantum dot: the ferromagnetic-antiferromagnetic transition”. Nguyen NTT, Peeters FM, Physical review : B : condensed matter and materials physics 78, 045321 (2008). http://doi.org/10.1103/PhysRevB.78.045321
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 3.836
Times cited: 41
DOI: 10.1103/PhysRevB.78.045321
|
“Nanowires and nanofilms: superconductivity in quantum-size regime”. Peeters FM, Croitoru MD, Shanenko AA, Physica: C : superconductivity 468, 326 (2008). http://doi.org/10.1016/j.physc.2007.07.013
Keywords: A1 Journal article; Condensed Matter Theory (CMT); Electron microscopy for materials research (EMAT)
Impact Factor: 1.404
Times cited: 3
DOI: 10.1016/j.physc.2007.07.013
|
“Advantages of combined mu-XRF and mu-XRD for phase characterization of Ti-B-C ceramics compared with conventional X-ray diffraction”. Jaroszewicz J, de Nolf W, Janssens K, Michalski A, Falkenberg G, Analytical and bioanalytical chemistry 391, 1129 (2008). http://doi.org/10.1007/S00216-008-2097-6
Keywords: A1 Journal article; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation)
Impact Factor: 3.431
Times cited: 7
DOI: 10.1007/S00216-008-2097-6
|