Abstract: Buildings are responsible for 40% of our worldwide energy consumption and 50% of this energy is converted for Heating Ventilation Air Conditioning (HVAC) systems in buildings. The increasing share of renewable energy production required to make the transition towards a carbon neutral energy system challenges the stability of the grid. Through demand response it becomes possible to activate these systems in support of grid balancing. However, this flexibility is currently not rewarded in the market. We simulate a domestic water heater participating in the balancing of the electricity net and calculated the revenue from this action. We simulate a water heater in connection with an Economic Model Predictive Controller (EMPC) which takes future usage, energy cost, and reward for delivering balanced power into account. We show that the choice of an EMPC controller is valid as it allows the setpoint to change if certain conditions are met, leading to a more optimal revenue stream from selling flexibility. We find that the economic benefits of participating in delivering balancing power is considerable and offset an increase in energy costs. The increase in energy consumption could be justified as the participation in net stabilisation allows the macro-system to integrate more renewable energy sources. More importantly, the simulations also show that the poorer the energy performance of the water heater, the more flexibility can be sold. From a policy point of view, a minimal energy performance should be determined before allowing participation in net stabilisation.

Abstract: Europe has somewhere between 150,000 and 500,000 landfill sites, with an estimated 90% of them being “non-sanitary” landfills, predating the EU Landfill Directive of 1999/31/EC. These older landfills tend to be filled with municipal solid waste and often lack any environmental protection technology. “ Doing nothing”, state-of-theart aftercare or remediating them depends largely on technical, societal and economic conditions which vary between countries. Beside “ doing nothing' and landfill aftercare, there are different scenarios in landfill mining, from re-landfilling the waste into ”sanitary landfills" to seizing the opportunity for a combined resource-recovery and remediation strategy. This review article addresses present and future issues and potential opportunities for landfill mining as an embedded strategy in current waste management systems through a multi-disciplinary approach. In particular, three general landfill mining strategies are addressed with varying extents of resource recovery. These are discussed in relation to the main targets of landfill mining: (i) reduction of the landfill volume (technical), (ii) reduction of risks and impacts (environmental) and (iii) increase in resource recovery and overall profitability (economic). Geophysical methods could be used to determine the characteristics of the landfilled waste and subsurface structures without the need of an invasive exploration, which could greatly reduce exploration costs and time, as well as be useful to develop a procedure to either discard or select the most appropriate sites for (E)LFM. Material and energy recovery from land-filled waste can be achieved through mechanical processing coupled with thermochemical valorization technologies and residues upcycling techniques. Gasification could enable the upcycling of residues after thermal treatment into a new range of eco-friendly construction materials based on inorganic polymers and glass-ceramics. The multi-criteria assessment is directly influenced by waste- and technology related factors, which together with site-specific conditions, market and regulatory aspects, influence the environmental, economic and societal impacts of (E)LFM projects.

Abstract: Understanding the perspectives of different stakeholders on emerging technological concepts is an important step towards their implementation. Enhanced Landfill Mining (ELFM) is one of these emerging concepts. It aims at valorizing past waste streams to higher added values in a sustainable manner. Yet, assessment of ELFM mainly focusses on environmental and private economic issues, and societal impacts are rarely analyzed. This study uses semi-structured interviews to build understanding for different ELFM practitioners and researchers and develops five stakeholder archetypes for ELFM implementation: the Engaged Citizen, the Entrepreneur, the Technology Enthusiast, the Visionary and the Skeptic. The archetypes outline major differences in approaching ELFM implementation. The stakeholder perceptions are put into context with existing literature, and implications for ELFM implementation and future research are discussed. Results show that differences in regulatory changes and technology choices are affected by different stakeholder perspectives and more research is needed to balance inner- and inter-dimensional conflicts of ELFM's sustainability. The developed archetypes can especially be helpful when evaluating social impacts, whose perception often depends on opinion and is difficult to quantify.

Abstract: This study focuses on the water-soluble ion concentrations in the washing solution of leaves of different roadside tree species at three sites in Iran to estimate the ionic composition of the dry deposition of ambient air particulates. All considered water-soluble ion concentrations were significantly higher next to the roads with high traffic density compared to the reference site with low traffic density. The PCA results showed that Ca2+, Mg2+, and originated mainly from traffic activities and geological sources, and Na+, Cl-, K+ and F- from sea salts. In addition to sea salt, K+ and F- were also originated from anthropogenic sources i.e. industrial activities, biomass burning and fluorite mining. Moreover, the concentration of the water-soluble ions depended on species and site. C. lawsoniana had significantly higher ion concentrations in its leaf washing solution compared to L. japonicum and P. brutia which indicates C. lawsoniana is the most suitable species for accumulating of atmospheric dry deposition. From our results, it can be concluded that sites with similar traffic density can have different particle loads and water-soluble ion species, and that concentrations in leaf-washing solutions depend on site conditions and species-specific leaf surface characteristics.

Abstract: Hydroxyapatite (HAP) is frequently used as biocompatible coating on Ti-based implants. In this context, the HAP-Ti adhesion is of crucial importance. Here, we report ab initio calculations to investigate the influence of Si incorporation into the amorphous calcium-phosphate (a-HAP) structure on the interfacial bonding mechanism between the a-HAP coating and an amorphous titanium dioxide (a-TiO2) substrate, contrasting two different density functionals: PBE-GGA, and DFT-D3, which are capable of describing the influence of the van der Waals (vdW) interactions. In particular, we discuss the effect of dispersion on the work of adhesion (W-ad), equilibrium geometries, and charge density difference (CDD). We find that replacement of P by Si in a-HAP (a-Si-HAP) with the creation of OH vacancies as charge compensation results in a significant increase in the bond strength between the coating and substrate in the case of using the PBE-GGA functional. However, including the vdW interactions shows that these forces considerably contribute to the W-ad. We show that the difference (W-ad – W-ad(vdW)) is on average more than 1.1 J m(-2) and 0.5 J m(-2) for a-HAP/a-TiO2 and a-Si-HAP/a-TiO2, respectively. These results reveal that including vdW interactions is essential for accurately describing the chemical bonding at the a-HAP/a-TiO2 interface.

Abstract: In the present work, kelvin probe force microscopy (KPFM) technique has been used to study the CZTSe/CuxSe bilayer interface prepared by multi-step deposition and selenization process of metal precursors. Transmission electron microscopy (TEM) confirmed the bilayer configuration of the CZTSe/CuxSe sample. Two configuration modes (surface mode and junction mode) in KPFM have been employed in order to measure the junction voltage under illumination conditions. The results show that CZTSe/CuxSe has small junction voltage of similar to 21 mV and the presence of CuxSe secondary phase in the CZTSe grain boundaries changes the workfunction of the local grain boundaries region. The negligible photovoltage difference between grain and grain boundaries in photovoltage image indicates that CuxSe phase deteriorates the higher photovoltage at grain boundaries normally observed in CZTSe based device. These results can be important for understanding the role of secondary phases in CZTSe based junction devices.