Home | [1–100] << 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 >> [201–249] |
![]() |
Records | |||||
---|---|---|---|---|---|
Author | Zhao, L.; Macias, J.G.S.; Ding, L.; Idrissi, H.; Simar, A. | ||||
Title | Damage mechanisms in selective laser melted AlSi10Mg under as built and different post-treatment conditions | Type | A1 Journal article | ||
Year | 2019 | Publication | Microstructure And Processing | Abbreviated Journal | Mat Sci Eng A-Struct |
Volume | 764 | Issue | 764 | Pages | 138210 |
Keywords | A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) | ||||
Abstract | Selective laser melting (SLM) manufactured AlSi10Mg alloys present a fine silicon-rich network and precipitates which grant high mechanical strength but low ductility. Post-treatments, aiming at eliminating inherent defects related to SLM such as residual stresses, porosity or inhomogeneity, result in significant changes in the microstructure and impact both the hardening and the damage mechanisms of the post-treated material. The present work is dedicated to the investigation of the fracture of SLM AlSi10Mg under as built and three post-treatment conditions, namely two stress relieve heat treatments and friction stir processing (FSP). It is found that the interconnected Si network fosters damage at low strain due to the brittleness of the Si phase. The onset of damage transfers load to the enclosed Al phase which then fractures quickly under high stress, thus leading to low material ductility. In contrast, when the Si network is globularized into Si particles, the ductility is highly increased even in the case where the porosity and inhomogeneity of the microstructure remain after the post-treatment. The ductility enhancement results from the delay in void nucleation on the Si particles as well as from the tolerance for void growth in the Al matrix. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000486360100029 | Publication Date | 2019-07-27 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN ![]() |
0921-5093 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.094 | Times cited | 1 | Open Access | |
Notes | ; This research work has been supported by the WALInnov LongLifeAM project, Convention n 1810016, funded by Service public de Wallonie Economic Emploi Recherche (SPW-EER). L. Ding and A. Simar acknowledge the financial support of the European Research Council (ERC) for the Starting Grant ALUFIX project (grant agreement n 716678). J. G. Santos Macias acknowledges the support of the Fonds de la recherche scientifique -FNRS (FRIA grant), Belgium. H. Idrissi is mandated by the Belgian National Fund for Scientific Research (FSRFNRS). Any-Shape is acknowledged for material supply. We thank Prof. P. J. Jacques from UCLouvain for fruitful discussion and critical reading of the paper. ; | Approved | Most recent IF: 3.094 | ||
Call Number | UA @ admin @ c:irua:162800 | Serial | 5386 | ||
Permanent link to this record | |||||
Author | Yang, M.; Chen, H.; Orekhov, A.; Lu, Q.; Lan, X.; Li, K.; Zhang, S.; Song, M.; Kong, Y.; Schryvers, D.; Du, Y. | ||||
Title | Quantified contribution of β″ and β′ precipitates to the strengthening of an aged Al–Mg–Si alloy | Type | A1 Journal article | ||
Year | 2020 | Publication | Materials Science And Engineering A-Structural Materials Properties Microstructure And Processing | Abbreviated Journal | Mat Sci Eng A-Struct |
Volume | 774 | Issue | Pages | 138776 | |
Keywords | A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) | ||||
Abstract | It is generally believed that β00 precipitates, rather than β0 precipitates, are the major strengthening precipitates in aged Al–Mg–Si alloys. The reason for this difference is not well understood. To clarify this, two samples of the same Al–Mg–Si alloy but with different aging states were prepared. The under-aged sample only contains nanoprecipitates of the β00 type, while the peak-aged one contains nearly equal volumes of β00 and β0 precipitates. We have, for the first time, separated the strengthening effect of the contribution from βʺ and βʹ precipitates, respectively, by an indirect approach based on high-precision measurements of volume fractions, number densities, sizes, proportions of the precipitates, their lattice strains, the composition and grain size of the matrix. The β0 precipitates, which take 45.6% of the total precipitate volume in the peak-aged sample, contribute to the entire precipitation strengthening by only 31.6%. The main reason why they are less useful compared to β00 precipitates has been found to be associated with their smaller lattice strains relative to the matrix, which is 0.99% versus 2.10% (for β00 ). |
||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000514747200001 | Publication Date | 2019-12-04 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN ![]() |
0921-5093 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 6.4 | Times cited | Open Access | OpenAccess | |
Notes | National Natural Science Foundation of China, 51531009 51711530713 51501230 ; Central South University, 2018gczd033 ; Flemish Science Foundation, VS.026.18N ; Program for Guangdong Introducing Innovative and Entrepreneurial Teams, 2016ZT06G025 ; Guangdong Natural Science Foundation, 2017B030306014 ; | Approved | Most recent IF: 6.4; 2020 IF: 3.094 | ||
Call Number | EMAT @ emat @c:irua:165290 | Serial | 5440 | ||
Permanent link to this record | |||||
Author | Morsdorf, L.; Kashiwar, A.; Kübel, C.; Tasan, C.C. | ||||
Title | Carbon segregation and cementite precipitation at grain boundaries in quenched and tempered lath martensite | Type | A1 Journal article | ||
Year | 2023 | Publication | Materials science and engineering: part A: structural materials: properties, microstructure and processing | Abbreviated Journal | |
Volume | 862 | Issue | Pages | 144369-21 | |
Keywords | A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) | ||||
Abstract | Tempering is widely applied to make carbon atoms beneficially rearrange in high strength steel microstructures after quenching; though the nano-scale interaction of carbon atoms with crystallographic defects is hard to experimentally observe. To improve, we investigate the redistribution of carbon atoms along martensite grain boundaries in a quenched and tempered low carbon steel. We observe the tempering-induced microstructural evolution by in-situ heating in a transmission electron microscope (TEM) and by compositional analysis through atom probe tomography (APT). Probe volumes for APT originate from a single martensite packet but in different tempering conditions, which is achieved via a sequential lift-out with in-between tempering treatments. The complementary use of TEM and APT provides crystallographic as well as chemical information on carbon segregation and subsequent carbide precipitation at martensite grain boundaries. The results show that the amount of carbon segregation to martensite grain boundaries is influenced by the boundary type, e.g. low-angle lath or high-angle block boundaries. Also, the growth behavior of cementite precipitates from grain boundary nucleation sites into neighboring martensite grains differs at low- and high-angle grain boundaries. This is due to the crystallographic constraints arising from the semi-coherent orientation relationship between cementite and adjacent martensite. We also show that slower quenching stabilizes thin retained austenite films between martensite grains because of enhanced carbon segregation during cooling. Finally, we demonstrate the effect of carbon redistribution along martensite grain boundaries on the mechanical properties. Here, we compare micro-scale Vickers hardness results from boundary-containing probe volumes to nanoindentation results from pure bulk martensite (boundary-free) probe volumes. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000905165700001 | Publication Date | 2022-12-07 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN ![]() |
0921-5093 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 6.4 | Times cited | Open Access | Not_Open_Access | |
Notes | Approved | Most recent IF: 6.4; 2023 IF: 3.094 | |||
Call Number | UA @ admin @ c:irua:192279 | Serial | 7285 | ||
Permanent link to this record | |||||
Author | Schryvers, D.; Potapov, P.; Santamarta, R.; Tirry, W. | ||||
Title | Applications of advanced transmission electron microscopic techniques to Ni-Ti based shape memory materials | Type | A1 Journal article | ||
Year | 2004 | Publication | Materials science and engineering: part A: structural materials: properties, microstructure and processing | Abbreviated Journal | Mat Sci Eng A-Struct |
Volume | 378 | Issue | 1/2 | Pages | 11-15 |
Keywords | A1 Journal article; Electron microscopy for materials research (EMAT) | ||||
Abstract | |||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Lausanne | Editor | ||
Language | Wos | 000223329900003 | Publication Date | 2004-03-23 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN ![]() |
0921-5093; | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.094 | Times cited | 6 | Open Access | |
Notes | Approved | Most recent IF: 3.094; 2004 IF: 1.445 | |||
Call Number | UA @ lucian @ c:irua:48783 | Serial | 145 | ||
Permanent link to this record | |||||
Author | Giorgio, S.; Henry, C.R.; Pauwels, B.; Van Tendeloo, G. | ||||
Title | Au particles supported on (110) anatase-TiO2 | Type | A1 Journal article | ||
Year | 2001 | Publication | Microstructure And Processing | Abbreviated Journal | Mat Sci Eng A-Struct |
Volume | 297 | Issue | 1-2 | Pages | 197-202 |
Keywords | A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) | ||||
Abstract | Au particles were prepared by evaporation in ultra high vacuum at high temperature, on the surfaces of TiO2 micro-spheres with the anatase structure. The morphology and the structural deformation in Au deposits were studied by high resolution transmission electron microscopy and image simulations by the multislice technique. The particles were polyhedral, limited by (100) and (111) faces. Patches with a hexagonal lattice were found around the particles, which was interpreted as thin Au islands on the surface. In these islands the Au lattice was deformed and perfectly accommodated to the (110) surface of TiO2. (C) 2001 Elsevier Science B.V. All rights reserved. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Lausanne | Editor | ||
Language | Wos | 000166241400026 | Publication Date | 2002-07-25 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN ![]() |
0921-5093; | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.094 | Times cited | 40 | Open Access | |
Notes | Approved | Most recent IF: 3.094; 2001 IF: 0.978 | |||
Call Number | UA @ lucian @ c:irua:104204 | Serial | 206 | ||
Permanent link to this record | |||||
Author | Srivastava, A.K.; Yang, Z.; Schryvers, D.; van Hurnbeeck, J. | ||||
Title | Effect of annealing on cold-rolled Ni-Ti alloys | Type | A1 Journal article | ||
Year | 2008 | Publication | Materials science and engineering: part A: structural materials: properties, microstructure and processing | Abbreviated Journal | Mat Sci Eng A-Struct |
Volume | 481 | Issue | Si | Pages | 594-597 |
Keywords | A1 Journal article; Electron microscopy for materials research (EMAT) | ||||
Abstract | |||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000255716100123 | Publication Date | 2007-06-07 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN ![]() |
0921-5093; | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.094 | Times cited | 8 | Open Access | |
Notes | Fwo; G0465.05 | Approved | Most recent IF: 3.094; 2008 IF: 1.806 | ||
Call Number | UA @ lucian @ c:irua:69141 | Serial | 797 | ||
Permanent link to this record | |||||
Author | Yang, Z.Q.; Schryvers, D. | ||||
Title | Electron energy-loss spectroscopy study of NiTi shape memory alloys | Type | A1 Journal article | ||
Year | 2008 | Publication | Materials science and engineering: part A: structural materials: properties, microstructure and processing | Abbreviated Journal | Mat Sci Eng A-Struct |
Volume | 481 | Issue | Pages | 214-217 | |
Keywords | A1 Journal article; Electron microscopy for materials research (EMAT) | ||||
Abstract | |||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000255716100041 | Publication Date | 2007-06-11 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN ![]() |
0921-5093; | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.094 | Times cited | 7 | Open Access | |
Notes | Gao | Approved | Most recent IF: 3.094; 2008 IF: 1.806 | ||
Call Number | UA @ lucian @ c:irua:69156 | Serial | 934 | ||
Permanent link to this record | |||||
Author | Bouvier, S.; Benmhenni, N.; Tirry, W.; Gregory, F.; Nixon, M.E.; Cazacu, O.; Rabet, L. | ||||
Title | Hardening in relation with microstructure evolution of high purity \alpha-titanium deformed under monotonic and cyclic simple shear loadings at room temperature | Type | A1 Journal article | ||
Year | 2012 | Publication | Materials science and engineering: part A: structural materials: properties, microstructure and processing | Abbreviated Journal | Mat Sci Eng A-Struct |
Volume | 535 | Issue | Pages | 12-21 | |
Keywords | A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) | ||||
Abstract | The aim of this paper is to gain understanding of the quasi-static, large strain deformation behavior at room-temperature of high-purity alpha-Ti with an initial split-basal texture. Simple shear tests were conducted along different directions in order to quantify the material's anisotropy and hardening evolution for different strain paths such as monotonic, Bauschinger, and cyclic loadings. The stress-strain curves indicate that the material displays strong anisotropy in the flow behavior. In order to capture the link between microstructure evolution (occurrence of twinning, grain size evolution, etc.) and the macroscopic response, a thoroughly detailed multi-scale characterization using scanning electron microscope (SEM) observations and electron backscattered diffraction (EBSD) analysis was also conducted. Specifically, EBSD analyses indicate that the twin activity and grain fragmentation are responsible for the observed difference between the macroscopic hardening rates corresponding to different directions and loading paths. (C) 2011 Elsevier B.V. All rights reserved. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Lausanne | Editor | ||
Language | Wos | 000301402400003 | Publication Date | 2011-12-17 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN ![]() |
0921-5093; | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.094 | Times cited | 22 | Open Access | |
Notes | Approved | Most recent IF: 3.094; 2012 IF: 2.108 | |||
Call Number | UA @ lucian @ c:irua:97824 | Serial | 1410 | ||
Permanent link to this record | |||||
Author | Tirry, W.; Schryvers, D. | ||||
Title | High resolution TEM study of Ni4Ti3 precipitates in austenitic Ni51Ti49 | Type | A1 Journal article | ||
Year | 2004 | Publication | Materials science and engineering: part A: structural materials: properties, microstructure and processing | Abbreviated Journal | Mat Sci Eng A-Struct |
Volume | 378 | Issue | 1/2 | Pages | 157-160 |
Keywords | A1 Journal article; Electron microscopy for materials research (EMAT) | ||||
Abstract | |||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Lausanne | Editor | ||
Language | Wos | 000223329900028 | Publication Date | 2004-04-10 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN ![]() |
0921-5093; | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.094 | Times cited | 19 | Open Access | |
Notes | Approved | Most recent IF: 3.094; 2004 IF: 1.445 | |||
Call Number | UA @ lucian @ c:irua:48785 | Serial | 1461 | ||
Permanent link to this record | |||||
Author | Coghe, F.; Tirry, W.; Rabet, L.; Schryvers, D.; Van Houtte, P. | ||||
Title | Importance of twinning in static and dynamic compression of a Ti-6Al-4V titanium alloy with an equiaxed microstructure | Type | A1 Journal article | ||
Year | 2012 | Publication | Materials science and engineering: part A: structural materials: properties, microstructure and processing | Abbreviated Journal | Mat Sci Eng A-Struct |
Volume | 537 | Issue | Pages | 1-10 | |
Keywords | A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) | ||||
Abstract | Whereas deformation twinning is known to be an important deformation mechanism for hexagonal materials like magnesium and pure titanium, so far almost no literature exists on the twinning behaviour of the Ti-6Al-4V alloy. In this work it was shown that the activation of twinning as a deformation mechanism could have a pronounced effect on the mechanical behaviour of the Ti-6Al-4V alloy. This effect is even more pronounced under dynamic loading conditions. Transmission electron microscopy showed that only the {1 0 1 2}{1 0 1 1} tensile twin system was activated under certain loading conditions. Light-optical microscopy and electron backscatter diffraction data were afterwards used to experimentally determine the twin fractions. The importance of twinning for the texture evolution was also studied. It was shown that even small twin fractions can lead to distinct texture features, especially due to the discrete reorientation of the c-axes. The experimental results were compared to simulated results that were obtained with a viscoplastic self-consistent crystal plasticity code, after experimental validation that twinning can be reliably modelled as a unidirectional slip system. Although good agreement was obtained for the experimental and simulated stress-strain curves, the simulated results concerning twinning correlated well only on a qualitative basis as the simulated twin fractions were systematically higher than the experimental fractions. This seems to strengthen the hypothesis made by other research groups that complete grains might reorient by twinning. (C) 2011 Elsevier B.V. All rights reserved. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Lausanne | Editor | ||
Language | Wos | 000301473300001 | Publication Date | 2011-12-21 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN ![]() |
0921-5093; | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.094 | Times cited | 35 | Open Access | |
Notes | Approved | Most recent IF: 3.094; 2012 IF: 2.108 | |||
Call Number | UA @ lucian @ c:irua:97818 | Serial | 1565 | ||
Permanent link to this record | |||||
Author | Tirry, W.; Schryvers, D. | ||||
Title | In situ transmission electron microscopy of stress-induced martensite with focus on martensite twinning | Type | A1 Journal article | ||
Year | 2008 | Publication | Materials science and engineering: part A: structural materials: properties, microstructure and processing | Abbreviated Journal | Mat Sci Eng A-Struct |
Volume | 481 | Issue | Si | Pages | 420-425 |
Keywords | A1 Journal article; Electron microscopy for materials research (EMAT) | ||||
Abstract | |||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000255716100087 | Publication Date | 2007-06-07 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN ![]() |
0921-5093; | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.094 | Times cited | 22 | Open Access | |
Notes | Approved | Most recent IF: 3.094; 2008 IF: 1.806 | |||
Call Number | UA @ lucian @ c:irua:69139 | Serial | 1586 | ||
Permanent link to this record | |||||
Author | Schryvers, D.; Holland-Moritz, D. | ||||
Title | Martensitic transformations and microstructures in splat-cooled Ni-Al | Type | A1 Journal article | ||
Year | 1999 | Publication | Materials science and engineering: part A: structural materials: properties, microstructure and processing | Abbreviated Journal | Mat Sci Eng A-Struct |
Volume | 273/275 | Issue | Pages | 697-702 | |
Keywords | A1 Journal article; Electron microscopy for materials research (EMAT) | ||||
Abstract | |||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Lausanne | Editor | ||
Language | Wos | 000084560400122 | Publication Date | 2002-07-25 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN ![]() |
0921-5093; | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.094 | Times cited | 6 | Open Access | |
Notes | Approved | Most recent IF: 3.094; 1999 IF: 0.943 | |||
Call Number | UA @ lucian @ c:irua:29380 | Serial | 1949 | ||
Permanent link to this record | |||||
Author | Schryvers, D.; Tirry, W.; Yang, Z.Q.; | ||||
Title | Measuring strain fields and concentration gradients around Ni4Ti3 precipitates | Type | A1 Journal article | ||
Year | 2006 | Publication | Materials science and engineering A: structural materials properties microstructure and processing | Abbreviated Journal | Mat Sci Eng A-Struct |
Volume | 438 | Issue | Pages | 485-488 | |
Keywords | A1 Journal article; Electron microscopy for materials research (EMAT) | ||||
Abstract | |||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000242900900105 | Publication Date | 2006-07-12 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN ![]() |
0921-5093; | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.094 | Times cited | 35 | Open Access | |
Notes | Goa | Approved | Most recent IF: 3.094; 2006 IF: 1.490 | ||
Call Number | UA @ lucian @ c:irua:62329 | Serial | 1969 | ||
Permanent link to this record | |||||
Author | Tirry, W.; Coghe, F.; Bouvier, S.; Gasperini, M.; Rabet, L.; Schryvers, D. | ||||
Title | A multi-scale characterization of deformation twins in Ti6Al4V sheet material deformed by simple shear | Type | A1 Journal article | ||
Year | 2010 | Publication | Materials science and engineering: part A: structural materials: properties, microstructure and processing | Abbreviated Journal | Mat Sci Eng A-Struct |
Volume | 527 | Issue | 16/17 | Pages | 4136-4145 |
Keywords | A1 Journal article; Electron microscopy for materials research (EMAT) | ||||
Abstract | Ti6Al4V sheet material is subjected to simple shear deformation with strain ratio's of 10%, 30% and 50%. Optical microscopy, transmission electron microscopy and electron backscatter diffraction techniques are applied to study the presence and morphology of deformation twins. Only the View the MathML source type of twins seems to be present with a volume fraction below 1%. These View the MathML source twins show a high density of basal stacking faults of the ABABACAC type identified using atomic resolution transmission electron microscopy. A resolved shear stress analysis shows that twins most often occur on those planes with the highest resolved shear stresses, but that the starting texture is not beneficial for the occurrence of twins. It is further suggested that a transitory strain hardening regime observed around 530 MPa might be related with the onset of twinning. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Lausanne | Editor | ||
Language | Wos | 000278766800068 | Publication Date | 2010-03-23 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN ![]() |
0921-5093; | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.094 | Times cited | 20 | Open Access | |
Notes | Iap | Approved | Most recent IF: 3.094; 2010 IF: 2.101 | ||
Call Number | UA @ lucian @ c:irua:82291 | Serial | 2212 | ||
Permanent link to this record | |||||
Author | Rotaru, G.-M.; Schryvers, D. | ||||
Title | New (3(3)under-bar) long-period microtwin variant in the martensitic phase of the PtTi alloy | Type | A1 Journal article | ||
Year | 2008 | Publication | Materials science and engineering: part A: structural materials: properties, microstructure and processing | Abbreviated Journal | Mat Sci Eng A-Struct |
Volume | 481 | Issue | Si | Pages | 437-441 |
Keywords | A1 Journal article; Electron microscopy for materials research (EMAT) | ||||
Abstract | |||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000255716100090 | Publication Date | 2007-06-07 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN ![]() |
0921-5093; | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.094 | Times cited | 3 | Open Access | |
Notes | Multimat | Approved | Most recent IF: 3.094; 2008 IF: 1.806 | ||
Call Number | UA @ lucian @ c:irua:69140 | Serial | 2300 | ||
Permanent link to this record | |||||
Author | Tirry, W.; Schryvers, D.; Jorissen, K.; Lamoen, D. | ||||
Title | Quantitative determination of the crystal structure of Ni4Ti3 precipitates | Type | A1 Journal article | ||
Year | 2006 | Publication | Materials science and engineering: part A: structural materials: properties, microstructure and processing | Abbreviated Journal | Mat Sci Eng A-Struct |
Volume | 438 | Issue | Pages | 517-520 | |
Keywords | A1 Journal article; Electron microscopy for materials research (EMAT) | ||||
Abstract | |||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Lausanne | Editor | ||
Language | Wos | 000242900900112 | Publication Date | 2006-07-12 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN ![]() |
0921-5093; | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.094 | Times cited | 7 | Open Access | |
Notes | Mrtn-Ct-2004-505226 | Approved | Most recent IF: 3.094; 2006 IF: 1.490 | ||
Call Number | UA @ lucian @ c:irua:61577 | Serial | 2752 | ||
Permanent link to this record | |||||
Author | Udoh, K.-I.; El- Araby, A.M.; Tanaka, Y.; Hisatsune, K.; Yasuda, K.; Van Tendeloo, G.; van Landuyt, J. | ||||
Title | Structural aspects of AuCu I or AuCu II and a cuboidal black configuration of f.c.c. disordered phase in AuCu-Pt and AuCu-Ag pseudobinary alloys | Type | A1 Journal article | ||
Year | 1995 | Publication | Materials science and engineering: part A: structural materials: properties, microstructure and processing | Abbreviated Journal | Mat Sci Eng A-Struct |
Volume | 203 | Issue | Pages | 154-164 | |
Keywords | A1 Journal article; Electron microscopy for materials research (EMAT) | ||||
Abstract | |||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Lausanne | Editor | ||
Language | Wos | A1995TM62800016 | Publication Date | 2002-07-25 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN ![]() |
0921-5093; | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 2.567 | Times cited | 15 | Open Access | |
Notes | Approved | ||||
Call Number | UA @ lucian @ c:irua:13298 | Serial | 3205 | ||
Permanent link to this record | |||||
Author | Santamarta, R.; Schryvers, D. | ||||
Title | Structure of multi-grain spherical particles in an amorphous Ti50Ni25Cu25 melt-spun ribbon | Type | A1 Journal article | ||
Year | 2004 | Publication | Materials science and engineering: part A: structural materials: properties, microstructure and processing | Abbreviated Journal | Mat Sci Eng A-Struct |
Volume | 378 | Issue | 1/2 | Pages | 143-147 |
Keywords | A1 Journal article; Electron microscopy for materials research (EMAT) | ||||
Abstract | |||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Lausanne | Editor | ||
Language | Wos | 000223329900025 | Publication Date | 2004-04-10 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN ![]() |
0921-5093; | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.094 | Times cited | 5 | Open Access | |
Notes | Approved | Most recent IF: 3.094; 2004 IF: 1.445 | |||
Call Number | UA @ lucian @ c:irua:48784 | Serial | 3311 | ||
Permanent link to this record | |||||
Author | Monot, I.; Tancret, F.; Laffez, P.; Van Tendeloo, G.; Desgardin, G. | ||||
Title | Microstructure and properties of oxygen controlled melt textured NdBaCuO superconductive ceramics | Type | A1 Journal article | ||
Year | 1999 | Publication | Technology | Abbreviated Journal | Mater Sci Eng B-Adv |
Volume | 65 | Issue | 1 | Pages | 26-34 |
Keywords | A1 Journal article; Electron microscopy for materials research (EMAT) | ||||
Abstract | Nd1+xBa2-xCu3O7-delta (123) bulk superconductors have been synthesised by the oxygen controlled melt growth method. Unlike the YBaCuO system, platinum doping or Nd4Ba2Cu2O10 (422) rich compositions do not refine the peritectic '422' secondary phase, but the latter improves the microstructural quality. Low oxygen partial pressure and high purity precursors are necessary to achieve in a reproducible manner high T-c and J(c) (up to 56 000 A/cm(2) in 0T and 30 000 A/cm(2) under 1.5T). The fishtail effect observed at 77 K is compared with the one observed in the YBCO system, and is discussed in terms of oxygen deficiency, Nd-Ba substitution, defects and vortex lattice. Our TEM observations did not evidence any Nd-Ba substituted clusters in the Nd123 matrix; however, some diffuse streaks, observed in the [100] zone ED pattern, support the fact that the source of the peak effect in this system is mainly due to oxygen disorder and low stability of the orthorhombic phase. (C) 1999 Elsevier Science S.A. All rights reserved. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Lausanne | Editor | ||
Language | Wos | 000083432000005 | Publication Date | 2002-07-25 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN ![]() |
0921-5107; | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 2.552 | Times cited | 5 | Open Access | |
Notes | Approved | Most recent IF: 2.552; 1999 IF: 0.690 | |||
Call Number | UA @ lucian @ c:irua:104286 | Serial | 2060 | ||
Permanent link to this record | |||||
Author | Ang, F.; Van Passel, S. | ||||
Title | The sustainable value approach : a clarifying and constructive comment | Type | A1 Journal article | ||
Year | 2010 | Publication | Ecological Economics | Abbreviated Journal | Ecol Econ |
Volume | 69 | Issue | 12 | Pages | 2303-2306 |
Keywords | A1 Journal article; Economics | ||||
Abstract | Recently, the original benchmarking methodology of the Sustainable Value approach became subjected to serious debate. While Kuosmanen and Kuosmanen (2009b) critically question its validity introducing productive efficiency theory, Figge and Hahn (2009) put forward that the implementation of productive efficiency theory severely conflicts with the original financial economics perspective of the Sustainable Value approach. We argue that the debate is very confusing because the original Sustainable Value approach presents two largely incompatible objectives. Nevertheless, we maintain that both ways of benchmarking could provide useful and moreover complementary insights. If one intends to present the overall resource efficiency of the firm from the investor's viewpoint, we recommend the original benchmarking methodology. If one on the other hand aspires to create a prescriptive tool setting up some sort of reallocation scheme, we advocate implementation of the productive efficiency theory. Although the discussion on benchmark application is certainly substantial, we should avoid the debate to become accordingly narrowed. Next to the benchmark concern, we see several other challenges considering the development of the Sustainable Value approach: (1) a more systematic resource selection, (2) the inclusion of the value chain and (3) additional analyses related to policy in order to increase interpretative power. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000283700900001 | Publication Date | 2010-07-30 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN ![]() |
0921-8009; 1873-6106 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles; WoS full record; WoS citing articles | |
Impact Factor | 2.965 | Times cited | 18 | Open Access | |
Notes | ; ; | Approved | Most recent IF: 2.965; 2010 IF: 2.754 | ||
Call Number | UA @ admin @ c:irua:136760 | Serial | 6258 | ||
Permanent link to this record | |||||
Author | Daniels, S.; Bellmore, J.R.; Benjamin, J.R.; Witters, N.; Vangronsveld, J.; Van Passel, S. | ||||
Title | Quantification of the indirect use value of functional group diversity based on the ecological role of species in the ecosystem | Type | A1 Journal article | ||
Year | 2018 | Publication | Ecological Economics | Abbreviated Journal | Ecol Econ |
Volume | 153 | Issue | 153 | Pages | 181-194 |
Keywords | A1 Journal article; Economics; Engineering Management (ENM) | ||||
Abstract | An important issue in biodiversity valuation is gaining a better understanding of how biodiversity conservation affects economic activities and human welfare. Quantifying the economic benefits of biodiversity for human well-being is not straightforward. Here, we expand the ecosystem service cascade by (i) attributing a methodology to the different steps of the cascade to assess the effects of changes in functional group diversity on economic activities; (ii) including multiple attributes for defining functional diversity and (iii) integrating a dynamic ecological model simulating complex interactions and feedbacks between species with an economic model assessing the effects of changes in functional group diversity for gross revenues. The stepwise methodological framework integrates a production function approach with a market price-based approach in order to investigate the indirect use value of functional group diversity based on the ecological role of species in the ecosystem. The methodology is applied to estimate the relationship between the gross economic value of Chinook salmon (Pacific Northwest, United States) and the diversity of freshwater macroinvertebrates. The results of our analysis emphasize the importance of biological diversity for sustaining ecosystem goods and services. The analysis provides a tractable framework for quantitatively exploring the economic consequences of changes in functional group diversity. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000443669200016 | Publication Date | 2018-07-31 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN ![]() |
0921-8009; 1873-6106 | ISBN | Additional Links | UA library record; WoS full record | |
Impact Factor | 2.965 | Times cited | Open Access | ||
Notes | ; The authors would like to thank Ken Bagstad for his valuable comments. The research was made possible with the financial aid from a BOF grant of the Centre for Environmental Sciences (CMK, Hasselt University, BE) (BSFFEEC-R4270). Nele Witters is funded by Research Foundation-Flanders (FWO). Any use of trade, firm, or product names is for descriptive purposes only and does not imply endorsement by the U.S. Government. ; | Approved | Most recent IF: 2.965 | ||
Call Number | UA @ admin @ c:irua:153598 | Serial | 6239 | ||
Permanent link to this record | |||||
Author | Jouzi, Z.; Azadi, H.; Taheri, F.; Zarafshani, K.; Gebrehiwot, K.; Van Passel, S.; Lebailly, P. | ||||
Title | Organic farming and small-scale farmers : main opportunities and challenges | Type | A1 Journal article | ||
Year | 2017 | Publication | Ecological Economics | Abbreviated Journal | Ecol Econ |
Volume | 132 | Issue | Pages | 144-154 | |
Keywords | A1 Journal article; Economics; Engineering Management (ENM) | ||||
Abstract | Producing enough food to meet the needs of a growing population has always been the greatest concern of food policy-makers around the world. Given the increasing attention to organic farming (OF), we conducted this study to investigate the main opportunities and challenges of the food production system of small-scale farmers in developing countries with an emphasis on their livelihoods. The study showed that the most significant advantages of OF are environmental protection and a higher resilience to environmental changes, increasing farmers' income and reducing external input cost, enhancing social capacity and increasing employment opportunities. A s well as enhancing food security primarily by increasing the food purchasing power of local people. However, the main challenges of this food production system include lower yields in comparison to conventional systems, difficulties with soil nutrient management, certification and market barriers, and the educational and research needs of small-holders. The paper concludes that even though OF might present some significant challenges to small-scale farmers, it could/should still be considered as a part of the solution and means of improving their livelihoods. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000390825200014 | Publication Date | 2016-11-06 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN ![]() |
0921-8009; 1873-6106 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles; WoS full record; WoS citing articles | |
Impact Factor | 2.965 | Times cited | 39 | Open Access | |
Notes | ; ; | Approved | Most recent IF: 2.965 | ||
Call Number | UA @ admin @ c:irua:139034 | Serial | 6233 | ||
Permanent link to this record | |||||
Author | Daniels, S.; Witters, N.; Beliën, T.; Vrancken, K.; Vangronsveld, J.; Van Passel, S. | ||||
Title | Monetary valuation of natural predators for biological pest control in pear production | Type | A1 Journal article | ||
Year | 2017 | Publication | Ecological Economics | Abbreviated Journal | Ecol Econ |
Volume | 134 | Issue | Pages | 160-173 | |
Keywords | A1 Journal article; Economics; Engineering Management (ENM) | ||||
Abstract | In spite of global actions, biodiversity is declining at an alarming rate. Despite the need for objectively comparable monetary standards to include biodiversity arguments in policymaking, research on the relationship between species diversity and its valuation from a societal perspective is still scarce. In this paper, a methodological framework for the valuation of natural predators based on their ecological role in the agroecosystem is introduced. The framework integrates a dynamic ecological model simulating interactions between species with an economic model, thereby quantifying the effect of reduced numbers of natural predators on the net farm income. The model attributes an objective monetary value to increased species diversity through the changes in the provisioning of a marketable good. Results indicate that the loss of three predators could decrease net farm income with 88.86 ha− 1 to 2186.5 ha− 1. For the pear production sector in Flanders in 2011, this constitutes to an indirect use value of 0,68 million for one predator and 16.63 million for the presence of three predators. The aim is to provide a justification for the argument for biodiversity conservation, based on the ecological function of species, through the delivery of comparable monetary standards. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000395219300018 | Publication Date | 2017-01-26 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN ![]() |
0921-8009; 1873-6106 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles; WoS full record; WoS citing articles | |
Impact Factor | 2.965 | Times cited | 4 | Open Access | |
Notes | ; The research was made possible with the financial aid from a BOF grant of the Centre for Environmental Sciences (CMK, Hasselt University). Nele Witters is funded by Research Foundation-Flanders (FWO). The authors would like to thank Ellen Elias from Symbio for providing relevant data and insights into the complex interplay between pest insects, natural predators and human impacts from fertilizers and pesticide use. ; | Approved | Most recent IF: 2.965 | ||
Call Number | UA @ admin @ c:irua:140685 | Serial | 6228 | ||
Permanent link to this record | |||||
Author | Van Passel, S.; Nevens, F.; Mathijs, E.; Van Huylenbroeck, G. | ||||
Title | Measuring farm sustainability and explaining differences in sustainable efficiency | Type | A1 Journal article | ||
Year | 2007 | Publication | Ecological Economics | Abbreviated Journal | Ecol Econ |
Volume | 62 | Issue | 1 | Pages | 149-161 |
Keywords | A1 Journal article; Economics | ||||
Abstract | A major objective of European agricultural policy is to have a sustainable and efficient farming sector that is applying environmentally-friendly production methods. Policy makers aim to combine a strong economic performance and a sustainable use of natural resources. Therefore, it is important to measure and to assess farm sustainability. For a large dataset of Flemish dairy farms, a valuation method that is based on the concept of opportunity costs is used to calculate and analyze differences among the sample farms with respect to the creation of sustainable value. But more important than measuring the creation of sustainable value is to analyze differences in sustainable efficiency. Therefore, sustainable efficiency measures are calculated and differences in sustainable efficiency are explained. Using panel data, an effect model captures the determinants of sustainable efficiency of the studied farms. The empirical model shows that, in general, larger farms have a higher sustainable efficiency. Also farmer's age and dependency on support payments proved to be determining characteristics for observed differences in sustainable efficiency. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000246021800015 | Publication Date | 2006-07-22 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN ![]() |
0921-8009; 1873-6106 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 2.965 | Times cited | 101 | Open Access | |
Notes | Approved | Most recent IF: 2.965; 2007 IF: 1.549 | |||
Call Number | UA @ admin @ c:irua:136767 | Serial | 6226 | ||
Permanent link to this record | |||||
Author | Pour, M.D.; Motiee, N.; Barati, A.A.; Taheri, F.; Azadi, H.; Gebrehiwot, K.; Lebailly, P.; Van Passel, S.; Witlox, F. | ||||
Title | Impacts of the Hara biosphere reserve on livelihood and welfare in Persian Gulf | Type | A1 Journal article | ||
Year | 2017 | Publication | Ecological Economics | Abbreviated Journal | Ecol Econ |
Volume | 141 | Issue | Pages | 76-86 | |
Keywords | A1 Journal article; Economics; Engineering Management (ENM) | ||||
Abstract | Despite the importance of biosphere reserves in Iran's livelihood and welfare, the economic significance of Hara Biosphere Reserve has never been comprehensively studied. This study examines the current importance of Hara Biosphere Reserve (HBR) in local livelihood and welfare. Using a household survey, data were collected through a questionnaire, key informant interviews and direct observations. Two hundred and forty-four households were randomly selected from 10 villages through proportional sampling. Results showed that non-environmental income was the first driver of the total income, poverty alleviation and narrowing income inequality gap. Park income was the second. The results also showed that excluding park income from total income would significantly increase headcount poverty, widen the poverty gap, and raise the Gini coefficient. Wealthier households had the greatest absolute income from the environment, including forest, fishing and fodder. However, the poorest group had smallest absolute income from these sources. Thus, the study demonstrated that wealthier households are responsible for the overharvesting of environmental resources. Interestingly, the study showed that wealthier households are more dependent on profitable environmental incomes sources while the poorest are more dependent on non-profitable ones. (C) 2017 Elsevier B.V. All rights reserved. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000410013200008 | Publication Date | 2017-06-02 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN ![]() |
0921-8009; 1873-6106 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles; WoS full record; WoS citing articles | |
Impact Factor | 2.965 | Times cited | 7 | Open Access | |
Notes | ; ; | Approved | Most recent IF: 2.965 | ||
Call Number | UA @ admin @ c:irua:145602 | Serial | 6214 | ||
Permanent link to this record | |||||
Author | Boerema, A.; Van Passel, S.; Meire, P. | ||||
Title | Cost-effectiveness analysis of ecosystem management with ecosystem services : from theory to practice | Type | A1 Journal article | ||
Year | 2018 | Publication | Ecological Economics | Abbreviated Journal | Ecol Econ |
Volume | 152 | Issue | 152 | Pages | 207-218 |
Keywords | A1 Journal article; Economics; Engineering Management (ENM); Ecosystem Management | ||||
Abstract | Integrated ecosystem management is challenging due to many, often conflicting, targets and limited resources to allocate. A valuable and straightforward approach is to integrate an ecosystem services assessment in a cost-effectiveness analysis as method to evaluate and compare the cost-effectiveness of several management scenarios to reach one or more objectives and take into account the potential effects on other ecosystem functions and services. Nevertheless, this method is not commonly used in ecosystem management evaluation but can provide an alternative for the frequently used but often contested cost-benefit analysis (which requires the step of assigning a monetary value to each benefit). The aim of this study is to apply the cost-effectiveness analysis in combination with an ecosystem services assessment on a real case-study (comparing alternative management strategies for estuaries) to derive lessons learned to go from theory to practice. The application of this method for the case-study reveals many remaining challenges such as data availability and knowledge to assess ecosystem effects of management measures. Nevertheless, the analysis demonstrates that this method can be used for making a more integrated evaluation and supporting better-informed management decisions. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000440118700021 | Publication Date | 2018-06-19 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN ![]() |
0921-8009; 1873-6106 | ISBN | Additional Links | UA library record; WoS full record | |
Impact Factor | 2.965 | Times cited | 2 | Open Access | |
Notes | ; ; | Approved | Most recent IF: 2.965 | ||
Call Number | UA @ admin @ c:irua:151754 | Serial | 6173 | ||
Permanent link to this record | |||||
Author | Ang, F.; Van Passel, S.; Mathijs, E. | ||||
Title | An aggregate resource efficiency perspective on sustainability : a sustainable value application to the EU-15 countries | Type | A1 Journal article | ||
Year | 2011 | Publication | Ecological Economics | Abbreviated Journal | Ecol Econ |
Volume | 71 | Issue | Pages | 99-110 | |
Keywords | A1 Journal article; Economics | ||||
Abstract | The Sustainable Value approach integrates the efficiency with regard to environmental, social and economic resources into a monetary indicator. It gained significant popularity as evidenced by diverse applications at the corporate level. However, its introduction as a measure adhering to the strong sustainability paradigm sparked an ardent debate. This study explores its validity as a macroeconomic strong sustainability measure by applying the Sustainable Value approach to the EU-15 countries. Concretely, we assessed environmental, social and economic resources in combination with the GDP for all EU-15 countries from 1995 to 2006 for three benchmark alternatives. The results show that several countries manage to adequately delink resource use from GDP growth. Furthermore, the remarkable difference in outcome between the national and EU-15 benchmark indicates a possible inefficiency of the current allocation of national resource ceilings imposed by the European institutions. Additionally, by using an effects model we argue that the service degree of the economy and governmental expenditures on social protection and research and development are important determinants of overall resource efficiency. Finally, we sketch out three necessary conditions to link the Sustainable Value approach to the strong sustainability paradigm. (C) 2011 Elsevier B.V. All rights reserved. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000297396700011 | Publication Date | 2011-09-28 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN ![]() |
0921-8009; 1873-6106 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles; WoS full record; WoS citing articles | |
Impact Factor | 2.965 | Times cited | 12 | Open Access | |
Notes | ; ; | Approved | Most recent IF: 2.965; 2011 IF: 2.713 | ||
Call Number | UA @ admin @ c:irua:127560 | Serial | 6151 | ||
Permanent link to this record | |||||
Author | Moretti, M.; Vanschoenwinkel, J.; Van Passel, S. | ||||
Title | Accounting for externalities in cross-sectional economic models of climate change impacts | Type | A1 Journal article | ||
Year | 2021 | Publication | Ecological Economics | Abbreviated Journal | Ecol Econ |
Volume | 185 | Issue | Pages | 107058 | |
Keywords | A1 Journal article; Economics; Engineering Management (ENM) | ||||
Abstract | Environmental effects and natural resources depletion associated with agriculture production affect the agriculture response to climate change. Traditional cross-sectional climate response models ignore this requirement. This research estimates the impact of climate on European agriculture using a continental scale Ricardian analysis. We correct farm income by accounting for resources (energy, fertilisers, pesticides, and water) use intensity and calculate the sustainable value for a sample of 9497 specialized field crop farms. Compared with the traditional Ricardian method, the marginal effects of temperature remain positive (but less positive) in Northern countries, while it leads to less damages in Southern countries when net revenue and farms? sustainable values are used as dependent variables. Accounting for the environmental effects and depletion of natural capital improves the ability of the Ricardian method to estimate agriculture climate response functions in the long run. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000647544700012 | Publication Date | 2021-04-05 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN ![]() |
0921-8009; 1873-6106 | ISBN | Additional Links | UA library record; WoS full record | |
Impact Factor | 2.965 | Times cited | Open Access | OpenAccess | |
Notes | Approved | Most recent IF: 2.965 | |||
Call Number | UA @ admin @ c:irua:178955 | Serial | 6911 | ||
Permanent link to this record | |||||
Author | Bjørnåvold, A.; David, M.; Bohan, D.A.; Gibert, C.; Rousselle, J.-M.; Van Passel, S. | ||||
Title | Why does France not meet its pesticide reduction targets? Farmers' socio-economic trade-offs when adopting agro-ecological practices | Type | A1 Journal article | ||
Year | 2022 | Publication | Ecological Economics | Abbreviated Journal | Ecol Econ |
Volume | 198 | Issue | Pages | 107440-28 | |
Keywords | A1 Journal article; Economics; Engineering Management (ENM) | ||||
Abstract | Despite substantial policy efforts made by the French government to reduce dependence on pesticides, farming practices are only changing slowly. This paper analyses the socio-economic trade-offs that 110 farmers are currently facing in the transition to agro-ecological practices. A mixed-method approach – a quantitative discrete choice experiment (DCE) and qualitative interviews – was set up to understand these farmers' motivations and perspectives, and how policy can improve to accompany them on the road to low chemical input farming. Results of the DCE indicate that the majority of the farmers in our sample are keen to change practices but are at a loss as to how this can be done, as a number of preferences for this transition came out as inconclusive. Qualitative interviews with a representative sample of the farmers that took part in the DCE complemented this result by illustrating a deep uncertainty for the future and a disconnect felt between authorities and themselves as a group. We argue that this uncertainty contributed to a lack of clear-cut solutions established through the DCE. The indepth discussions with farmers illustrated the wish for concrete and local policy measures based on farmers' networks and peer support. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000802083900003 | Publication Date | 2022-05-07 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN ![]() |
0921-8009; 1873-6106 | ISBN | Additional Links | UA library record; WoS full record | |
Impact Factor | 7 | Times cited | Open Access | OpenAccess | |
Notes | Approved | Most recent IF: 7 | |||
Call Number | UA @ admin @ c:irua:188764 | Serial | 7375 | ||
Permanent link to this record | |||||
Author | Zelaya, E.; Esquivel, M.R.; Schryvers, D. | ||||
Title | Evolution of the phase stability of NiAl under low energy ball milling | Type | A1 Journal article | ||
Year | 2013 | Publication | Advanced powder technology | Abbreviated Journal | Adv Powder Technol |
Volume | 24 | Issue | 6 | Pages | 1063-1069 |
Keywords | A1 Journal article; Electron microscopy for materials research (EMAT) | ||||
Abstract | Low energy mechanical alloying of Ni35 at.%Al and Ni40 at.%Al material was performed and the resulting structures were investigated by XRD and TEM. The final intermetallics observed consist of two phases, NiAl(B2) and Ni3Al while 7R and 3R martensite was observed in post-annealed samples. Different integrated milling times were associated to the intermetallic consolidation and initial blend dissociation. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Zeist | Editor | ||
Language | Wos | 000339175000024 | Publication Date | 2013-03-30 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN ![]() |
0921-8831; | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 2.659 | Times cited | 10 | Open Access | |
Notes | Fwo | Approved | Most recent IF: 2.659; 2013 IF: 1.642 | ||
Call Number | UA @ lucian @ c:irua:107345 | Serial | 1102 | ||
Permanent link to this record |