Records |
Author |
Volkov, V.V.; van Heurck, C.; van Landuyt, J.; Amelinckx, S.; Zhukov, E.G.; Polulyak, E.S.; Novotortsev, V.M. |
Title |
Electron microscopy and X-ray study of the growth of FeCr2S4 spinel single crystals by chemical vapour transport |
Type |
A1 Journal article |
Year |
1993 |
Publication |
Crystal research and technology |
Abbreviated Journal |
Cryst Res Technol |
Volume |
28 |
Issue |
8 |
Pages |
1051-1061 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
The growth features of FeCr2S4 spinel single crystals prepared by chemical vapour transport were studied by means of scanning electron microscopy, transmission electron microscopy, high resolution electron microscopy, electron diffraction and X-ray analysis. Our results indicate that the epitaxial growth of the new phases FeCr7S12 and FeCr8S12, both based on the NiAs structure, can essentially inhibit the growth of large FeCr2S4 spinel single crystals in the octahedral habit. The new phases are fully characterised and the effects of defect ordering in these new phases are also reported. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Berlin |
Editor |
|
Language |
|
Wos |
A1993MN86700003 |
Publication Date |
2007-01-13 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0232-1300;1521-4079; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
0.935 |
Times cited |
1 |
Open Access |
|
Notes |
|
Approved |
no |
Call Number |
UA @ lucian @ c:irua:6788 |
Serial |
952 |
Permanent link to this record |
|
|
|
Author |
De Dobbelaere, C.; Lourdes Calzada, M.; Bretos, I.; Jimenez, R.; Ricote, J.; Hadermann, J.; Hardy, A.; Van Bael, M.K. |
Title |
Gaining new insight into low-temperature aqueous photochemical solution deposited ferroelectric PbTiO3 films |
Type |
A1 Journal article |
Year |
2016 |
Publication |
Materials chemistry and physics |
Abbreviated Journal |
Mater Chem Phys |
Volume |
174 |
Issue |
|
Pages |
28-40 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
The nature of the low-temperature photochemical assisted formation process of ferroelectric lead titanate (PbTiO3) films is studied in the present work. Films are obtained by the deposition of an aqueous solution containing citric acid based (citrato) metal ion complexes with intrinsic UV activity. This UV activity is crucial for the aqueous photochemical solution deposition (aqueous PCSD) route being used. UV irradiation enhances the early decomposition of organics and results in improved electrical properties for the crystalline oxide film, even if the film is crystallized at low temperature. GATR-FTIR shows that UV irradiation promotes the decomposition of organic precursor components, resulting in homogeneous films if applied in the right temperature window during film processing. The organic content, morphology and crystallinity of the irradiated films, achieved at different processing atmospheres and temperatures, is studied and eventually correlated to the functional behavior of the obtained films. This is an important issue, as crystalline films obtained at low temperatures often lack ferroelectric responses. In this work, the film prepared in pure oxygen at the very low temperature of 400 degrees C and after an optimized UV treatment presents a significant remanent polarization value of P-r = 8.8 mu C cm(-2). This value is attributed to the better crystallinity, the larger grain size and the reduced porosity obtained thanks to the early film crystallization effectively achieved through the UV treatment in oxygen. (C) 2016 Elsevier B.V. All rights reserved. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Lausanne |
Editor |
|
Language |
|
Wos |
000373865700005 |
Publication Date |
2016-03-16 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0254-0584 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
2.084 |
Times cited |
4 |
Open Access |
|
Notes |
|
Approved |
Most recent IF: 2.084 |
Call Number |
UA @ lucian @ c:irua:144729 |
Serial |
4659 |
Permanent link to this record |
|
|
|
Author |
Thomé, T.; Colaux, J.L.; Colomer, J.-F.; Bertoni, G.; Terwagne, G. |
Title |
Formation of carbon nitride nanospheres by ion implantation |
Type |
A1 Journal article |
Year |
2007 |
Publication |
Materials chemistry and physics |
Abbreviated Journal |
Mater Chem Phys |
Volume |
103 |
Issue |
2-3 |
Pages |
290-294 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
Carbon nitride nanospheres have been synthesized into copper by simultaneous high fluence (10(18) at. cm(-2)) implantations of C-12 and N-15 ions. The composition of the implanted region has been measured using C-12(d,p(0))C-13 and N-15(d,alpha(0))C-13 nuclear reactions induced by a 1.05 MeV deuteron beam. The C-12 and N-15 depth profiles are very close and the retained doses into copper are relatively high, which indicates that carbon and nitrogen diffusion processes are likely limited during implantation. High resolution transmission electron microscopy (HRTEM) observations and electron diffraction (ED) analyses have been carried out to determine the structure of the nanospheres formed during implantation. Some consist in small hollow amorphous nanocapsules with sizes ranging from 30 to 100 nm. Large gas bubbles with diameters up to 300 mn have also been observed in the copper matrix. Electron energy-loss spectroscopy (EELS) measurements performed on the small nanocapsules indicate that their shells are composed of carbon and nitrogen. (c) 2007 Elsevier B.V. All rights reserved. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Lausanne |
Editor |
|
Language |
|
Wos |
000247715300016 |
Publication Date |
2007-02-25 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0254-0584; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
2.084 |
Times cited |
1 |
Open Access |
|
Notes |
|
Approved |
Most recent IF: 2.084; 2007 IF: 1.871 |
Call Number |
UA @ lucian @ c:irua:102670 |
Serial |
1258 |
Permanent link to this record |
|
|
|
Author |
Navío, C.; Vallejos, S.; Stoycheva, T.; Llobet, E.; Correig, X.; Snyders, R.; Blackman, C.; Umek, P.; Ke, X.; Van Tendeloo, G.; Bittencourt, C.; |
Title |
Gold clusters on WO3 nanoneedles grown via AACVD : XPS and TEM studies |
Type |
A1 Journal article |
Year |
2012 |
Publication |
Materials chemistry and physics |
Abbreviated Journal |
Mater Chem Phys |
Volume |
134 |
Issue |
2/3 |
Pages |
809-813 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
We have prepared tungsten oxide films decorated with gold particles on Si substrates by aerosol assisted chemical vapor deposition (AACVD) and characterized them using scanning electron microscopy (SEM), transmission electron microscopy (TEM) and X-ray photoelectron spectroscopy (XPS). SEM shows that the films are composed of needle-like structures and TEM shows that both the needles and the gold particles are crystalline. XPS indicates the presence of oxygen vacancies, i.e. the films are WO3−x, and hence the deposited material is composed of semiconducting nanostructures and that the interaction between the gold particles and the WO3 needles surface is weak. The synthesis of semiconducting tungsten oxide nanostructures decorated with metal particles represents an important step towards the development of sensing devices with optimal properties. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Lausanne |
Editor |
|
Language |
|
Wos |
000305918200038 |
Publication Date |
2012-04-30 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0254-0584; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
2.084 |
Times cited |
52 |
Open Access |
|
Notes |
Iap |
Approved |
Most recent IF: 2.084; 2012 IF: 2.072 |
Call Number |
UA @ lucian @ c:irua:97705 |
Serial |
1356 |
Permanent link to this record |
|
|
|
Author |
Lorenz, H.; Zhao, Q.; Turner, S.; Lebedev, O.I.; Van Tendeloo, G.; Klötzer, B.; Rameshan, C.; Penner, S. |
Title |
Preparation and structural characterization of SnO2 and GeO2 methanol steam reforming thin film model catalysts by (HR)TEM |
Type |
A1 Journal article |
Year |
2010 |
Publication |
Materials chemistry and physics |
Abbreviated Journal |
Mater Chem Phys |
Volume |
122 |
Issue |
2/3 |
Pages |
623-629 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
Structure, morphology and composition of different tin oxide and germanium oxide thin film catalysts for the methanol steam reforming (MSR) reaction have been studied by a combination of (high-resolution) transmission electron microscopy, selected area electron diffraction, dark-field imaging and electron energy-loss spectroscopy. Deposition of the thin films on NaCl(0 0 1) cleavage faces has been carried out by thermal evaporation of the respective SnO2 and GeO2 powders in varying oxygen partial pressures and at different substrate temperatures. Preparation of tin oxide films in high oxygen pressures (10−1 Pa) exclusively resulted in SnO phases, at and above 473 K substrate temperature epitaxial growth of SnO on NaCl(0 0 1) leads to well-ordered films. For lower oxygen partial pressures (10−3 to 10−2 Pa), mixtures of SnO and β-Sn are obtained. Well-ordered SnO2 films, as verified by electron diffraction patterns and energy-loss spectra, are only obtained after post-oxidation of SnO films at temperatures T ≥ 673 K in 105 Pa O2. Preparation of GeOx films inevitably results in amorphous films with a composition close to GeO2, which cannot be crystallized by annealing treatments in oxygen or hydrogen at temperatures comparable to SnO/SnO2. Similarities and differences to neighbouring oxides relevant for selective MSR in the third group of the periodic system (In2O3 and Ga2O3) are also discussed with the aim of cross-correlation in formation of nanomaterials, and ultimately, also catalytic properties. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Lausanne |
Editor |
|
Language |
|
Wos |
000278637900054 |
Publication Date |
2010-04-18 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0254-0584; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
2.084 |
Times cited |
15 |
Open Access |
|
Notes |
Esteem 026019 |
Approved |
Most recent IF: 2.084; 2010 IF: 2.356 |
Call Number |
UA @ lucian @ c:irua:83099 |
Serial |
2699 |
Permanent link to this record |
|
|
|
Author |
Bampouli, A.; Goris, Q.; Hussain, M.N.; Louisnard, O.; Stefanidis, G.D.; Van Gerven, T. |
Title |
Importance of design and operating parameters in a sonication system for viscous solutions : effects of input power, horn tip diameter and reactor capacity |
Type |
A1 Journal article |
Year |
2024 |
Publication |
Chemical engineering and processing |
Abbreviated Journal |
|
Volume |
198 |
Issue |
|
Pages |
109715-12 |
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
Abstract |
This study investigates the distribution of ultrasound (US) energy in a batch system for solutions with viscosity ranging from 1 to approximately 3000 mPas. Sonication was performed using horn type configurations operating at 20-30 kHz and rated power capacity of 50 or 200 W. Two different tip diameters (3 or 7 mm) and two insertion depths (35 or 25 mm) within vessels of different sizes ( approximate to 60 or 130 ml) were utilized. Additionally, a special conical tip design was employed. For each experimental setup, the calorimetric efficiency was estimated, the cavitationally active regions were visualized using the sonochemiluminescence (SCL) method and bubble cluster formation inside the vessel was macroscopically observed using a high speed camera (HSC). In the viscosity range tested, the calorimetry results showed that the efficiency and continuous operation of the device depend on both the rated power and the horn tip diameter. The ratio between electrical and calorimetric power input remained consistently around 40 to 50% across the different configurations for water, but for the 123.2 mPas solution exhibited significant variation ranging from 40 to 85%. Moreover, the power density in the smaller reactor was found to be nearly double compared to the larger one. The SCL analysis showed multiple cavitationally active zones in all setups, and the zones intensity decreased considerably with increase of the solutions viscosity. The results for the cone tip were not conclusive, but can be used as the basis for further investigation. The current research highlights the importance of thoroughly understanding the impact of each design parameter, and of establishing characterization methodologies to assist in the future development of scaled-up, commercial applications. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
001218630800001 |
Publication Date |
2024-02-21 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0255-2701 |
ISBN |
|
Additional Links |
UA library record; WoS full record |
Impact Factor |
4.3 |
Times cited |
|
Open Access |
|
Notes |
|
Approved |
Most recent IF: 4.3; 2024 IF: 2.234 |
Call Number |
UA @ admin @ c:irua:206003 |
Serial |
9154 |
Permanent link to this record |
|
|
|
Author |
Romano-Rodriguez, A.; Perez-Rodriguez, A.; Serre, C.; van Landuyt, J.; et al. |
Title |
Epitaxial growth of \beta-SiC on ion-beam synthesized \beta-SiC : structural characterization |
Type |
A1 Journal article |
Year |
2000 |
Publication |
Materials science forum
T2 – International Conference on Silicon Carbide and Related Materials, OCT 10-15, 1999, RES TRIANGLE PK, NORTH CAROLINA |
Abbreviated Journal |
Mater Sci Forum |
Volume |
338-3 |
Issue |
|
Pages |
309-312 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
In this work we present for the first time, to our knowledge, the CVD epitaxial growth of beta -SiC using an ion beam synthesized (IBS) beta -SiC layer as seed, which has been formed by multiple implantation into Si wafers at 500 degreesC. The ion beam synthesized continuous layer is constituted by beta -SiC nanocrystals that are well oriented relative to the silicon substrate. Comparison of the epitaxial growth on these samples with that on silicon test samples, both on and off-axis, is performed. The results show that the epitaxial growth can be achieved on the IBS samples without the need of the carbonization step and that the structural quality of the CVD layer is comparable to that obtained on a carbonized silicon sample. Improvement of the quality of the deposited layer is proposed. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
Trans tech publications ltd |
Place of Publication |
Zurich-uetikon |
Editor |
|
Language |
|
Wos |
000165996700075 |
Publication Date |
0000-00-00 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0255-5476 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
|
Times cited |
2 |
Open Access |
|
Notes |
|
Approved |
Most recent IF: NA |
Call Number |
UA @ lucian @ c:irua:104262 |
Serial |
1071 |
Permanent link to this record |
|
|
|
Author |
Krsmanovic, R.; Bertoni, G.; Van Tendeloo, G. |
Title |
Structural characterization of erbium doped LAS glass ceramics obtained by glass melting technique |
Type |
A1 Journal article |
Year |
2007 |
Publication |
Materials science forum |
Abbreviated Journal |
|
Volume |
555 |
Issue |
|
Pages |
377-381 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
Samples of transparent glass-ceramics in the ternary system Li2O-Al2O3-SiO2 (LAS), with Er2O3 as a luminescent dopant, are investigated. The initial glass is obtained by the classical melting technique. In order to induce ceramization of the glass, TiO2 and ZrO2 are added in small amount as nucleating agents. The thermal treatments at 730 and 770 degrees C are carried out to promote formation of titanium zirconate solid solution precipitates. The spatial distribution of the precipitates in the material, their morphology, and their composition are investigated with TEM, HRTEM, HAADF-STEM, EELS and EFTEM. The results demonstrate that with the glass-melting preparation technique it is possible to achieve small nanoparticles with uniform distribution and higher number density than with the sol-gel glass preparation. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Lausanne |
Editor |
|
Language |
|
Wos |
|
Publication Date |
0000-00-00 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0255-5476 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
|
Times cited |
|
Open Access |
|
Notes |
|
Approved |
Most recent IF: NA |
Call Number |
UA @ lucian @ c:irua:94673 |
Serial |
3220 |
Permanent link to this record |
|
|
|
Author |
van Landuyt, J.; Van Tendeloo, G.; Amelinckx, S.; Zhang, X.F.; Zhang, X.B.; Luyten, W. |
Title |
Crystallography of fullerites and related graphene textures |
Type |
A1 Journal article |
Year |
1994 |
Publication |
Materials science forum |
Abbreviated Journal |
|
Volume |
150/151 |
Issue |
|
Pages |
53-64 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
|
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Lausanne |
Editor |
|
Language |
|
Wos |
A1994BC12F00004 |
Publication Date |
0000-00-00 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0255-5476; 1662-9752 |
ISBN |
|
Additional Links |
UA library record; WoS full record; |
Impact Factor |
|
Times cited |
|
Open Access |
|
Notes |
|
Approved |
no |
Call Number |
UA @ lucian @ c:irua:10001 |
Serial |
590 |
Permanent link to this record |
|
|
|
Author |
Teodorescu, V.S.; Nistor, L.C.; van Landuyt, J. |
Title |
High resolution TEM observation of in situ colloid formation in CaF2 crystals |
Type |
A1 Journal article |
Year |
1997 |
Publication |
Materials science forum |
Abbreviated Journal |
|
Volume |
239-241 |
Issue |
|
Pages |
671-674 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
|
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Lausanne |
Editor |
|
Language |
|
Wos |
A1997BH33W00145 |
Publication Date |
0000-00-00 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0255-5476; 1662-9752 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
|
Times cited |
3 |
Open Access |
|
Notes |
|
Approved |
Most recent IF: NA |
Call Number |
UA @ lucian @ c:irua:21404 |
Serial |
1460 |
Permanent link to this record |
|
|
|
Author |
Kee-Hyun, K.; van Daele, B.; Van Tendeloo, G.; Jong-Kyu, Y. |
Title |
Observations of intermetallic compound formation of hot dip aluminized steel |
Type |
A1 Journal article |
Year |
2006 |
Publication |
Aluminium alloys: part 1-2 |
Abbreviated Journal |
|
Volume |
519-521 |
Issue |
1-2 |
Pages |
1871-1875 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
A hot dip aluminizing process to simulate the continuous galvanizing line (CGL) was carried out in three successive steps by a hot dip simulator: the pre-treatment for removing scales on the 200 x 250 mm(2) and 1mm in thickness cold rolled steel sheet, the dipping in 660 degrees C Al-Si melt for 3s and the cooling. In a pre-treatment, the steel specimen was partly coated by Au to confirm the mechanism of intermetallic compound (IMC) formation. Scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX), and transmission electron microscopy (TEM) analyses were followed to observe the cross-section and the distribution of the elements. The specimen was analyzed in the boundary of the dipped-undipped part to see the formation mechanism of the aluminized steel. An intermetallic compound (IMC) is rapidly developed and grown in the steel-liquid interface. It has been usually reported that the IMC was formed by the dissolution of iron in the steel substrate toward the melt and the diffusion of aluminum in an opposite direction. The specimen is covered with aluminum-10 wt.% silicon, forms the IMC in the part that was not Au coated. However, IMC is not formed in the Au-coated part. The interface of the dipped-undipped is also analyzed by EDX. At the interface of the steel-IMC, it is clearly shown that the IMC is only formed in the dipped part and exists in the steel substrate as well, and contributes by iron, aluminum and silicon. The result clearly shows that only aluminum diffuses into the steel substrate without the dissolution of iron and forms the IMC between the steel substrate and the melt. Au coating and the short dipping time prevent the iron from dissolving into the aluminum melt. By TEM combined with focused ion beam (FIB) sample preparation, the IMC is confirmed as Fe2SiAl8, a hexagonal structure with space group P6(3)/mmc. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Lausanne |
Editor |
|
Language |
|
Wos |
|
Publication Date |
0000-00-00 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0255-5476; 1662-9752 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
|
Times cited |
|
Open Access |
|
Notes |
|
Approved |
Most recent IF: NA |
Call Number |
UA @ lucian @ c:irua:104062 |
Serial |
2425 |
Permanent link to this record |
|
|
|
Author |
Nistor, L.C.; van Landuyt, J.; Ralchenko, V.G.; Obratzova, E.D.; Korothushenko, K.G.; Smolin, A.A. |
Title |
Structural studies of nanocrystalline diamond thin films |
Type |
A1 Journal article |
Year |
1997 |
Publication |
Materials science forum |
Abbreviated Journal |
|
Volume |
239-241 |
Issue |
|
Pages |
115-118 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
|
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Lausanne |
Editor |
|
Language |
|
Wos |
A1997BH33W00026 |
Publication Date |
0000-00-00 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0255-5476; 1662-9752 |
ISBN |
|
Additional Links |
UA library record; WoS full record; |
Impact Factor |
|
Times cited |
|
Open Access |
|
Notes |
|
Approved |
Most recent IF: NA |
Call Number |
UA @ lucian @ c:irua:21403 |
Serial |
3260 |
Permanent link to this record |
|
|
|
Author |
Cremers, V.; Rampelberg, G.; Barhoum, A.; Walters, P.; Claes, N.; Oliveira, T.M. de; Assche, G.V.; Bals, S.; Dendooven, J.; Detavernier, C. |
Title |
Oxidation barrier of Cu and Fe powder by Atomic Layer Deposition |
Type |
A1 Journal article |
Year |
2018 |
Publication |
Surface and coatings technology |
Abbreviated Journal |
Surf Coat Tech |
Volume |
349 |
Issue |
349 |
Pages |
1032-1041 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
Atomic layer deposition (ALD) is a vapor based technique which allows to deposit uniform, conformal films with a thickness control at the atomic scale. In this research, Al 2 O 3 coatings were deposited on micrometer-sized Fe and Cu powder (particles) using the thermal trimethylaluminum (TMA)/ water (H 2 O) process in a rotary pump-type ALD reactor. Rotation of the powder during deposition was required to obtain a pinhole-free ALD coating. The protective nature of the coating was evaluated by quantifying its effectiveness in protecting the metal particles during oxidative annealing treatments. The Al 2 O 3 coated powders were annealed in ambient air while in-situ thermogravimetric analysis (TGA) and in-situ x-ray diffraction (XRD) data were acquired. The thermal stability of a series of Cu and Fe powder with different Al 2 O 3 thicknesses were determined with TGA. In both samples a clear shift in oxidation temperature is visible. For Cu and Fe powder coated with 25 nm Al 2 O 3 , we observed an increase of the oxidation temperature with 300-400°C. For the Cu powder a thin film of only 8 nm is required to obtain an initial increase in oxidation temperature of 200°C. In contrast, for Fe powder a thicker coating of 25 nm is required. In both cases, the oxidation temperature increases with increasing thickness of the Al 2 O 3 coating. These results illustrate that the Al 2 O 3 thin film, deposited by the thermal ALD process (TMA/H 2 O) can be an efficient and pinhole-free barrier layer for micrometer-sized powder particles, provided that the powder is properly agitated during the process to ensure sufficient vapour-solid interaction. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
000441492600108 |
Publication Date |
2018-06-25 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0257-8972 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
2.589 |
Times cited |
10 |
Open Access |
OpenAccess |
Notes |
The authors acknowledge financial support from the Strategic Initiative Materials in Flanders (SIM, SBO-FUNC project) and the Special Research Fund BOF of Ghent University (GOA 01G01513). J. D. acknowledges the Research Foundation Flanders (FWO-Vlaanderen) for a postdoctoral fellowship. N.C. and S.B. acknowledge financial support from European Research Council (ERC Starting Grant 335078-COLOURATOMS). The authors acknowledge S. Goeteyn for the assistance in preliminary depositions. (ROMEO:green; preprint:; postprint:can ; pdfversion:cannot); ecas_sara |
Approved |
Most recent IF: 2.589 |
Call Number |
EMAT @ emat @c:irua:152174UA @ admin @ c:irua:152174 |
Serial |
4994 |
Permanent link to this record |
|
|
|
Author |
Sharp, J.; Mueller, I.C.; Mandal, P.; Abbas, A.; Nord, M.; Doye, A.; Ehiasarian, A.; Hovsepian, P.; MacLaren, I.; Rainforth, W.M. |
Title |
Characterisation of a high-power impulse magnetron sputtered C/Mo/W wear resistant coating by transmission electron microscopy |
Type |
A1 Journal article |
Year |
2019 |
Publication |
Surface and coatings technology |
Abbreviated Journal |
Surf Coat Tech |
Volume |
377 |
Issue |
377 |
Pages |
124853 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
Thin films of C/Mo/W deposited using combined UBM/HIPIMS sputtering show 2-8 nm clusters of material richer in Mo and W than the matrix (found by EDS microanalysis), with structures that resemble graphitic onions with the metal atoms arranged regularly within them. EELS microanalysis showed the clusters to be rich in W and Mo. As the time averaged power used in the pulsed HIPIMS magnetron was increased, the clusters became more defined, larger, and arranged into layers with amorphous matrix between them. Films deposited with average HIPIMS powers of 4 kW and 6 kW also showed a periodic modulation of the cluster density within the finer layers giving secondary, wider stripes in TEM. By analysing the ratio between the finer and coarser layers, it was found that this meta-layering is related to the substrate rotation in the deposition chamber but in a non-straightforward way. Reasons for this are proposed. The detailed structure of the clusters remains unknown and is the subject of further work. Fluctuation electron microscopy results indicated the presence of crystal planes with the graphite interlayer spacing, crystal planes in hexagonal WC perpendicular to the basal plane, and some plane spacings found in Mo2C. Other peaks in the FEM results suggested symmetry-related starting points for future determination of the structure of the clusters. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
000488417800015 |
Publication Date |
2019-08-03 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0257-8972 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
2.589 |
Times cited |
1 |
Open Access |
|
Notes |
; J.S. thanks the Mercury Centre at the University of Sheffield for funding, which was part funded by the ERDF under grant MERCURY 904467. I.C.M. acknowledges support from CONACyT and RobertoRocca Education Fellowship. We gratefully acknowledge funding from EPSRC for the pixelated STEM detector and the software used in its operation for the fluctuation microscopy (EP/M009963/ 1, EP/K503903/1 & EP/R511705/1). AD was supported by the EPSRC CDT in Integrative Sensing and Measurement, Grant Number EP/L016753/1. Funding sources did not influence the planning or execution of this work except to enable it. ; |
Approved |
Most recent IF: 2.589 |
Call Number |
UA @ admin @ c:irua:163700 |
Serial |
5383 |
Permanent link to this record |
|
|
|
Author |
Mahieu, S.; Ghekiere, P.; de Winter, G.; de Gryse, R.; Depla, D.; Van Tendeloo, G.; Lebedev, O.I. |
Title |
Biaxially aligned titanium nitride thin films deposited by reactive unbalanced magnetron sputtering |
Type |
A1 Journal article |
Year |
2006 |
Publication |
Surface and coatings technology |
Abbreviated Journal |
Surf Coat Tech |
Volume |
200 |
Issue |
8 |
Pages |
2764-2768 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
|
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Lausanne |
Editor |
|
Language |
|
Wos |
000235202100023 |
Publication Date |
2004-12-15 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0257-8972; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
2.589 |
Times cited |
36 |
Open Access |
|
Notes |
IWT-Vlaanderen |
Approved |
Most recent IF: 2.589; 2006 IF: 1.559 |
Call Number |
UA @ lucian @ c:irua:56554 |
Serial |
229 |
Permanent link to this record |
|
|
|
Author |
Major, L.; Morgiel, J.; Major, B.; Lackner, J.M.; Waldhauser, W.; Ebner, R.; Nistor, L.; Van Tendeloo, G. |
Title |
Crystallographic aspects related to advanced tribological multilayers of Cr/CrN and Ti/TiN types produced by pulsed laser deposition (PLD) |
Type |
A1 Journal article |
Year |
2006 |
Publication |
Surface and coatings technology |
Abbreviated Journal |
Surf Coat Tech |
Volume |
200 |
Issue |
22/23 |
Pages |
6190-6195 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
|
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Lausanne |
Editor |
|
Language |
|
Wos |
000237842300007 |
Publication Date |
2005-12-10 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0257-8972; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
2.589 |
Times cited |
32 |
Open Access |
|
Notes |
|
Approved |
Most recent IF: 2.589; 2006 IF: 1.559 |
Call Number |
UA @ lucian @ c:irua:59459 |
Serial |
586 |
Permanent link to this record |
|
|
|
Author |
Major, L.; Tirry, W.; Van Tendeloo, G. |
Title |
Microstructure and defect characterization at interfaces in TiN/CrN multilayer coatings |
Type |
A1 Journal article |
Year |
2008 |
Publication |
Surface and coatings technology |
Abbreviated Journal |
Surf Coat Tech |
Volume |
202 |
Issue |
24 |
Pages |
6075-6080 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
Microstructures of TiN/CrN multilayer coatings deposited on austenite steel (Cr Ni 18 8) by pulsed laser deposition (PLD) are characterized using transmission electron microscopy while their mechanical properties were assessed in a ball-on-disk test. All coatings have the same total thickness of about 1 ìm. The individual layers show a highly defective columnar structure, which is characterized by conventional electron microscopy (TEM) as well as by high resolution TEM. These techniques, combined with measurements of the local chemical composition through EDS prove that PLD allows to produce fully separated CrN and TiN layers. The friction, and consequently the wear, are lowered by increasing the total number of layers in the coating. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Lausanne |
Editor |
|
Language |
|
Wos |
000260267100042 |
Publication Date |
2008-07-20 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0257-8972; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
2.589 |
Times cited |
23 |
Open Access |
|
Notes |
|
Approved |
Most recent IF: 2.589; 2008 IF: 1.860 |
Call Number |
UA @ lucian @ c:irua:76614 |
Serial |
2049 |
Permanent link to this record |
|
|
|
Author |
Huq, M.Z.; Celis, J.P.; Meneve, J.; Stals, L.; Schryvers, D. |
Title |
Oscillating sliding wear of mono- and multilayer ceramic coatings in air |
Type |
A1 Journal article |
Year |
1999 |
Publication |
Surface and coatings technology |
Abbreviated Journal |
Surf Coat Tech |
Volume |
113 |
Issue |
|
Pages |
242-250 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
|
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Lausanne |
Editor |
|
Language |
|
Wos |
000079807600007 |
Publication Date |
2002-07-25 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0257-8972; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
2.589 |
Times cited |
10 |
Open Access |
|
Notes |
|
Approved |
Most recent IF: 2.589; 1999 IF: 1.008 |
Call Number |
UA @ lucian @ c:irua:29379 |
Serial |
2532 |
Permanent link to this record |
|
|
|
Author |
Lamas, J.S.; Leroy, W.P.; Lu, Y.-G.; Verbeeck, J.; Van Tendeloo, G.; Depla, D. |
Title |
Using the macroscopic scale to predict the nano-scale behavior of YSZ thin films |
Type |
A1 Journal article |
Year |
2014 |
Publication |
Surface and coatings technology |
Abbreviated Journal |
Surf Coat Tech |
Volume |
238 |
Issue |
|
Pages |
45-50 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
In this work, Yttria-stabilized zirconia (YSZ) thin films were deposited using dual reactive magnetron sputtering. By varying the deposition conditions, the film morphology and texture of the thin films are tuned and biaxial alignment is obtained. Studying the crystallographic and microstructural properties of the YSZ thin films, a tilted columnar growth was identified. This tilt is shown to be dependent on the compositional gradient of the sample. The variation of composition within a single YSZ column measured via STEM-EDX is demonstrated to be equal to the macroscopic variation on a full YSZ sample when deposited under the same deposition parameters. A simple stress model was developed to predict the tilt of the growing columns. The results indicate that this model not only determines the column bending of the growing film but also confirms that a macroscopic approach is sufficient to determine the compositional gradient in a single column of the YSZ thin films. (C) 2013 Elsevier B.V. All rights reserved. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Lausanne |
Editor |
|
Language |
|
Wos |
000331028200005 |
Publication Date |
2013-10-29 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0257-8972; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
2.589 |
Times cited |
8 |
Open Access |
|
Notes |
246791 Countatoms; 278510 Vortex;Nmp3-La-2010-246102 Ifox; 312483 Esteem2; esteem2jra3 ECASJO; |
Approved |
Most recent IF: 2.589; 2014 IF: 1.998 |
Call Number |
UA @ lucian @ c:irua:115765 |
Serial |
3827 |
Permanent link to this record |
|
|
|
Author |
Zhou, C.; Ji, G.; Chen, Z.; Wang, M.; Addad, A.; Schryvers, D.; Wang, H. |
Title |
Fabrication, interface characterization and modeling of oriented graphite flakes/Si/Al composites for thermal management applications |
Type |
A1 Journal article |
Year |
2014 |
Publication |
Materials and design |
Abbreviated Journal |
Mater Design |
Volume |
63 |
Issue |
|
Pages |
719-728 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
Highly thermally conductive graphite flakes (Gf)/Si/Al composites have been fabricated using Gf, Si powder and an AlSi7Mg0.3 alloy by an optimized pressure infiltration process for thermal management applications. In the composites, the layers of Gf were spaced apart by Si particles and oriented perpendicular to the pressing direction, which offered the opportunity to tailor the thermal conductivity (TC) and coefficient of thermal expansion (CTE) of the composites. Microstructural characterization revealed that the formation of a clean and tightly-adhered interface at the nanoscale between the side surface of the Gf and Al matrix, devoid of a detrimental Al4C3 phase and a reacted amorphous AlSiOC layer, contributed to excellent thermal performance along the alignment direction. With increasing volume fraction of Gf from 13.7 to 71.1 vol.%, the longitudinal (i.e. parallel to the graphite layers) TC of the composites increased from 179 to 526 W/m K, while the longitudinal CTE decreased from 12.1 to 7.3 ppm/K (matching the values of electronic components). Furthermore, the modified layers-in-parallel model better fitted the longitudinal TC data than the layers-in-parallel model and confirmed that the clean and tightly-adhered interface is favorable for the enhanced longitudinal TC. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Reigate |
Editor |
|
Language |
|
Wos |
000340949300086 |
Publication Date |
2014-07-17 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0261-3069; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
|
Times cited |
61 |
Open Access |
|
Notes |
|
Approved |
Most recent IF: NA |
Call Number |
UA @ lucian @ c:irua:118124 |
Serial |
1166 |
Permanent link to this record |
|
|
|
Author |
Barhoum, A.; Van Assche, G.; Rahier, H.; Fleisch, M.; Bals, S.; Delplancked, M.-P.; Leroux, F.; Bahnemann, D. |
Title |
Sol-gel hot injection synthesis of ZnO nanoparticles into a porous silica matrix and reaction mechanism |
Type |
A1 Journal article |
Year |
2017 |
Publication |
Materials & design |
Abbreviated Journal |
Mater Design |
Volume |
119 |
Issue |
119 |
Pages |
270-276 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
Despite the enormous interest in the properties and applications of porous silica matrix, only a few attempts have been reported to deposit metal and metal oxide nanoparticles (NPs) inside the porous silica matrix. We report a simple approach (i.e. sol-gel hot injection) for insitu synthesis of ZnO NPs inside a porous silica matrix. Control of the Zn:Si molar ratio, reaction temperature, pH value, and annealing temperature permits formation of ZnO NPs (<= 10 nm) inside a porous silica particles, without additives or organic solvents. Results revealed that a solid state reaction inside the ZnO/SiO2 nanocomposites occurs with increasing the annealing temperature. The reaction of ZnO NPs with SiO2 matrix was insignificant up to approximately 500 degrees C. However, ZnO NPs react strongly with the silica matrix when the nanocomposites are annealed at temperatures above 700 degrees C. Extensive annealing of the ZnO/SiO2 nanocomposite at 900 degrees C yields 3D structures made of 500 nm rod-like, 5-7 pm tube-like and 35 pm needle-like Zn2SiO4 crystals. A possible mechanism for forming ZnO NPs inside porous silica matrix and phase transformation of the ZnO/SiO2 nanocomposites into 3D architectures of Zn2SiO4 are carefully discussed. (C) 2017 Elsevier Ltd. All rights reserved. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
000397360000030 |
Publication Date |
2017-01-23 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0264-1275 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
4.364 |
Times cited |
43 |
Open Access |
Not_Open_Access |
Notes |
; A.B. would like to thank FWO – Research Foundation Flanders (grant no. V450315N) and the Strategic Initiative Materials in Flanders (SBO-project no. 130529 – INSITU) for financial support. TEM and TEM-EDX analyses were performed by Dr. F. Leroux (EMAT, Universiteit Antwerpen). XRD and DSC measurements were performed by T. Segato (4MAT, Universite Libre de Bruxelles). Notes: the authors declare no competing for financial interest. ; |
Approved |
Most recent IF: 4.364 |
Call Number |
UA @ lucian @ c:irua:142394UA @ admin @ c:irua:142394 |
Serial |
4689 |
Permanent link to this record |
|
|
|
Author |
Radi, A.; Khalil-Allafi, J.; Etminanfar, M.R.; Pourbabak, S.; Schryvers, D.; Amin-Ahmadi, B. |
Title |
Influence of stress aging process on variants of nano-N4Ti3precipitates and martensitic transformation temperatures in NiTi shape memory alloy |
Type |
A1 Journal article |
Year |
2018 |
Publication |
Materials & design |
Abbreviated Journal |
Mater Design |
Volume |
262 |
Issue |
262 |
Pages |
74-81 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
In this study, the effect of a stress aging process on the microstructure and martensitic phase transformation of NiTi shape memory alloy has been investigated. NiTi samples were aged at 450 degrees C for 1 h and 5 h under different levels of external tensile stress of 15, 60 and 150 MPa. Transmission electron microscopy (TEM) was used to characterize different variants and morphology of precipitates. The results show that application of all stress levels restricts the formation of precipitates variants in the microstructure after I h stress aging process. However, all variants can be detected by prolonging aging time to 5 h at 15 MPa stress level and the variants formation is again restricted by increasing the stress level. Moreover, the stress aging process resulted in changing the shape of precipitates in comparison with that of the stress-free aged samples. Coffee-bean shaped morphologies were detected for precipitates in all stress levels. According to the Differential Scanning Calorimetry (DSC) results, the martensite start temperature (M-s) on cooling shifts to higher temperatures with increasing the tensile stress during the aging process. This can be related to the change ofaustenite to martensite interface energy due to the different volume fractions and variants of precipitates. (c) 2018 Elsevier Ltd. All rights reserved. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
|
Publication Date |
2018-01-04 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0264-1275 |
ISBN |
|
Additional Links |
UA library record; ; WoS full record; WoS citing articles |
Impact Factor |
4.364 |
Times cited |
|
Open Access |
OpenAccess |
Notes |
|
Approved |
Most recent IF: 4.364 |
Call Number |
UA @ lucian @ c:irua:149854 |
Serial |
4938 |
Permanent link to this record |
|
|
|
Author |
Miotti Bettanini, A.; Ding, L.; Mithieux, J.-D.; Parrens, C.; Idrissi, H.; Schryvers, D.; Delannay, L.; Pardoen, T.; Jacques, P.J. |
Title |
Influence of M23C6 dissolution on the kinetics of ferrite to austenite transformation in Fe-11Cr-0.06C stainless steel |
Type |
A1 Journal article |
Year |
2019 |
Publication |
Materials & design |
Abbreviated Journal |
Mater Design |
Volume |
162 |
Issue |
|
Pages |
362-374 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
The design of high-strength martensitic stainless steels requires an accurate control over the stability of undesired phases, like carbides and ferrite, which can hamper strength and ductility. Here, the ferrite to austenite transformation in Fe-11Cr-0.06C has been studied with a combined experimental-modelling approach. Experimental observations of the austenization process indicate that austenite growth proceeds in multiple steps, each one characterized by a different transformation rate. DICTRA based modelling reveals that the dissolution of the M23C6 Cr-rich carbides leads to Cr partitioning between austenite and parent phases, which controls the rate of transformation through (i) a soft-impingement effect and (ii) consequent stabilization of the ferrite, which remains untransformed inside chromium-enriched-zones even after prolonged austenization stage. Slow heating rate and smaller initial particle sizes allow the design of ferrite-free microstructure. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
000454128400036 |
Publication Date |
2018-12-06 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0264-1275 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
4.364 |
Times cited |
3 |
Open Access |
OpenAccess |
Notes |
The authors thank Professor Anne-Francoise Gourgues-Lorenzon and Helene Godin, Ecole Nationale Superiore des Mines de Paris (MINES ParisTech) for their fruitful discussions. AMB thanks Stijn Van den broek (Universiteit Antwerpen) for the skillful preparation of TEM samples with FIB. The financial support of CBMM (Companhia Brasileira de Metalurgia e Mineracao) is gratefully acknowledged. L. Delannay is mandated by the FNRS-Belgium. Computational resources have been provided by the supercomputing facilities of the UCLouvain (CISM/UCL) and the Consortium des Equipements de Calcul Intensif en Federation Wallonie Bruxelles (CÉCI) funded by the Fond de la Recherche Scientifique de Belgique (F.R.S.-FNRS) under convention 2.5020.11.; Cbmm; F.r.s.-fnrs, 2.5020.11 ; |
Approved |
Most recent IF: 4.364 |
Call Number |
EMAT @ emat @UA @ admin @ c:irua:156721 |
Serial |
5161 |
Permanent link to this record |
|
|
|
Author |
Montero-Sistiaga, M.L.; Pourbabak, S.; Van Humbeeck, J.; Schryvers, D.; Vanmeensel, K. |
Title |
Microstructure and mechanical properties of Hastelloy X produced by HP-SLM (high power selective laser melting) |
Type |
A1 Journal article |
Year |
2019 |
Publication |
Materials & design |
Abbreviated Journal |
Mater Design |
Volume |
165 |
Issue |
|
Pages |
107598 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
In order to increase the production rate during selective laser melting (SLM), a high power laser with a large beam diameter is used to build fully dense Hastelloy X parts. Compared to SLM with a low power and small diameter beam, the productivity was increased from 6 mm3/s to 16 mm3/s, i.e. 2.6 times faster. Besides the productivity benefit, the influence of the use of a high power laser on the rapid solidification microstructure and concomitant material properties is highlighted. The current paper compares the microstructure and tensile properties of Hastelloy X built with low and high power lasers. The use of a high power laser results in wider and shallower melt pools inducing an enhanced morphological and crystallographic texture along the building direction (BD). In addition, the increased heat input results in coarser sub-grains or high density dislocation walls for samples processed with a high power laser. Additionally, the influence of hot isostatic pressing (HIP) as a post-processing technique was evaluated. After HIP, the tensile fracture strain increased as compared to the strain in the as-built state and helped in obtaining competitive mechanical properties as compared to conventionally processed Hastelloy X parts. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
000458259300020 |
Publication Date |
2019-01-09 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0264-1275 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
4.364 |
Times cited |
15 |
Open Access |
OpenAccess |
Notes |
This research was supported by the ENGIE Research and Technology Division. The authors acknowledge ENGIE Research and Technology Division for the use of the SLM280HL machine. S.P. likes to thank the Flemish Science Foundation FWO for financial support under Project G.0366.15N. |
Approved |
Most recent IF: 4.364 |
Call Number |
EMAT @ emat @UA @ admin @ c:irua:157469 |
Serial |
5176 |
Permanent link to this record |
|
|
|
Author |
Bignoli, F.; Rashid, S.; Rossi, E.; Jaddi, S.; Djemia, P.; Terraneo, G.; Li Bassi, A.; Idrissi, H.; Pardoen, T.; Sebastiani, M.; Ghidelli, M. |
Title |
Effect of annealing on mechanical properties and thermal stability of ZrCu/O nanocomposite amorphous films synthetized by pulsed laser deposition |
Type |
A1 Journal article |
Year |
2022 |
Publication |
Materials & design |
Abbreviated Journal |
Mater Design |
Volume |
221 |
Issue |
|
Pages |
110972-10 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
Binary ZrCu nanocomposite amorphous films are synthetized by pulsed laser deposition (PLD) under vac-uum (2 x 10-3 Pa) and 10 Pa He pressure, leading to fully amorphous compact and nanogranular mor-phologies, respectively. Then, post-thermal annealing treatments are carried out to explore thermal stability and crystallization phenomena together with the evolution of mechanical properties. Compact films exhibit larger thermal stability with partial crystallization phenomena starting at 420 degrees C, still to be completed at 550 degrees C, while nanogranular films exhibit early-stage crystallization at 300 degrees C and com-pleted at 485 degrees C. The microstructural differences are related to a distinct evolution of mechanical |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
000886072100004 |
Publication Date |
2022-07-21 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0264-1275; 1873-4197 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
8.4 |
Times cited |
|
Open Access |
OpenAccess |
Notes |
|
Approved |
Most recent IF: 8.4 |
Call Number |
UA @ admin @ c:irua:192194 |
Serial |
7299 |
Permanent link to this record |
|
|
|
Author |
Gheysen, J.; Kashiwar, A.; Idrissi, H.; Villanova, J.; Simar, A. |
Title |
Suppressing hydrogen blistering in a magnesium-rich healable laser powder bed fusion aluminum alloy analyzed by in-situ high resolution techniques |
Type |
A1 Journal article |
Year |
2023 |
Publication |
Materials & design |
Abbreviated Journal |
|
Volume |
231 |
Issue |
|
Pages |
112024-11 |
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
Abstract |
Hydrogen blistering, i.e. precipitation of supersaturated hydrogen at elevated temperatures, increases porosity during heat treatments in 4xxx series Al alloys manufactured by laser powder bed fusion (LPBF), as demonstrated by 3D X-ray nano-imaging in AlSi12. This paper proposes the design of a healable Al alloy to suppress hydrogen blistering and improve the damage management. The strategy consists of solute atoms diffusing towards nano-voids and precipitating on their surface, thereby filling the damage sites. A new healable Al alloy was thus developed and successfully manufactured by LPBF. 3D X-ray nano-imaging evidenced that the addition of Mg in 4xxx series Al alloys suppresses the hydrogen blistering. This is expectedly due to Mg in solid solution which increases the hydrogen solubility in the Al matrix and due to the healing of these hydrogen pores. Moreover, a significant healing of voids smaller than 500 nm diameter is observed. In-situ heating inside transmission electron microscopy pointed out that Al matrix diffuses inside the fractured Mg2Si particles, thereby demonstrating the healing ability of the new alloy. This has opened the doors to development of new healable Al alloys manufactured by LPBF as well as to new post-treatments to tailor mechanical properties and microstructure without hydrogen blistering. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
001055174900001 |
Publication Date |
2023-05-20 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0264-1275; 1873-4197 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
8.4 |
Times cited |
|
Open Access |
OpenAccess |
Notes |
|
Approved |
Most recent IF: 8.4; 2023 IF: 4.364 |
Call Number |
UA @ admin @ c:irua:196536 |
Serial |
8939 |
Permanent link to this record |
|
|
|
Author |
Kashiwar, A.; Arseenko, M.; Simar, A.; Idrissi, H. |
Title |
On the role of microstructural defects on precipitation, damage, and healing behavior in a novel Al-0.5Mg2Si alloy |
Type |
A1 Journal article |
Year |
2024 |
Publication |
Materials & design |
Abbreviated Journal |
|
Volume |
239 |
Issue |
|
Pages |
112765-112769 |
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
Abstract |
A recently developed healable Al-Mg2Si designed by the programmed damage and repair (PDR) strategy is studied considering the role microstructural defects play on precipitation, damage, and healing. The alloy incorporates sacrificial Mg2Si particles that precipitate after friction stir processing (FSP). They act as damage localization sites and are healable based on the solid-state diffusion of Al-matrix. A combination of different transmission electron microscopy (TEM) imaging techniques enabled the visualization and quantification of various crystallographic defects and the spatial distribution of Mg2Si precipitates. Intragrain nucleation is found to be the dominant mechanism for precipitation during FSP whereas grain boundaries and subgrain boundaries mainly lead to coarsening of the precipitates. The statistical and spatial analyses of the damaged particles have shown particle fracture as the dominant damage mechanism which is strongly dependent on the size and aspect ratio of the particles whereas the damage was not found to depend on the location of the precipitates within the matrix. The damaged particles are associated with dislocations accumulated around them. The interplay of these dislocations is directly visualized during healing based on in situ TEM heating which revealed recovery in the matrix as an operative mechanism during the diffusion healing of the PDR alloy. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
001194110200001 |
Publication Date |
2024-02-17 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0264-1275; 1873-4197 |
ISBN |
|
Additional Links |
UA library record; WoS full record |
Impact Factor |
8.4 |
Times cited |
|
Open Access |
Not_Open_Access |
Notes |
|
Approved |
Most recent IF: 8.4; 2024 IF: 4.364 |
Call Number |
UA @ admin @ c:irua:203298 |
Serial |
9068 |
Permanent link to this record |
|
|
|
Author |
Kadu, A.; van Leeuwen, T.; Batenburg, K.J. |
Title |
CoShaRP : a convex program for single-shot tomographic shape sensing |
Type |
A1 Journal article |
Year |
2021 |
Publication |
Inverse Problems |
Abbreviated Journal |
Inverse Probl |
Volume |
37 |
Issue |
10 |
Pages |
105005 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
We introduce single-shot x-ray tomography that aims to estimate the target image from a single cone-beam projection measurement. This linear inverse problem is extremely under-determined since the measurements are far fewer than the number of unknowns. Moreover, it is more challenging than conventional tomography, where a sufficiently large number of projection angles forms the measurements, allowing for a simple inversion process. However, single-shot tomography becomes less severe if the target image is only composed of known shapes. This paper restricts analysis to target image function that can be decomposed into known compactly supported non-negative-valued functions termed shapes. Hence, the shape prior transforms a linear ill-posed image estimation problem to a non-linear problem of estimating the roto-translations of the shapes. We circumvent the non-linearity by using a dictionary of possible roto-translations of the shapes. We propose a convex program CoShaRP, to recover the dictionary coefficients successfully. CoShaRP relies on simplex-type constraints and can be solved quickly using a primal-dual algorithm. The numerical experiments show that CoShaRP recovers shape stably from moderately noisy measurements. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
000691743700001 |
Publication Date |
2021-07-23 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0266-5611 |
ISBN |
|
Additional Links |
UA library record; WoS full record |
Impact Factor |
1.62 |
Times cited |
|
Open Access |
OpenAccess |
Notes |
|
Approved |
Most recent IF: 1.62 |
Call Number |
UA @ admin @ c:irua:181617 |
Serial |
6859 |
Permanent link to this record |
|
|
|
Author |
Zeegers, M.T.; Kadu, A.; van Leeuwen, T.; Batenburg, K.J. |
Title |
ADJUST : a dictionary-based joint reconstruction and unmixing method for spectral tomography |
Type |
A1 Journal article |
Year |
2022 |
Publication |
Inverse problems |
Abbreviated Journal |
Inverse Probl |
Volume |
38 |
Issue |
12 |
Pages |
125002-125033 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
Advances in multi-spectral detectors are causing a paradigm shift in x-ray computed tomography (CT). Spectral information acquired from these detectors can be used to extract volumetric material composition maps of the object of interest. If the materials and their spectral responses are known a priori, the image reconstruction step is rather straightforward. If they are not known, however, the maps as well as the responses need to be estimated jointly. A conventional workflow in spectral CT involves performing volume reconstruction followed by material decomposition, or vice versa. However, these methods inherently suffer from the ill-posedness of the joint reconstruction problem. To resolve this issue, we propose 'A Dictionary-based Joint reconstruction and Unmixing method for Spectral Tomography' (ADJUST). Our formulation relies on forming a dictionary of spectral signatures of materials common in CT and prior knowledge of the number of materials present in an object. In particular, we decompose the spectral volume linearly in terms of spatial material maps, a spectral dictionary, and the indicator of materials for the dictionary elements. We propose a memory-efficient accelerated alternating proximal gradient method to find an approximate solution to the resulting bi-convex problem. From numerical demonstrations on several synthetic phantoms, we observe that ADJUST performs exceedingly well compared to other state-of-the-art methods. Additionally, we address the robustness of ADJUST against limited and noisy measurement patterns. The demonstration of the proposed approach on a spectral micro-CT dataset shows its potential for real-world applications. Code is available at https://github.com/mzeegers/ADJUST. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
000868885200001 |
Publication Date |
2022-09-20 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0266-5611 |
ISBN |
|
Additional Links |
UA library record; WoS full record |
Impact Factor |
2.1 |
Times cited |
|
Open Access |
Not_Open_Access |
Notes |
|
Approved |
Most recent IF: 2.1 |
Call Number |
UA @ admin @ c:irua:191536 |
Serial |
7280 |
Permanent link to this record |
|
|
|
Author |
Vanhellemont, J.; Romano Rodriguez, A.; Fedina, L.; van Landuyt, J.; Aseev, A. |
Title |
Point defect reactions in silicon studied in situ by high flux electron irradiation in high voltage transmission electron microscope |
Type |
A1 Journal article |
Year |
1995 |
Publication |
Materials science and technology |
Abbreviated Journal |
Mater Sci Tech-Lond |
Volume |
11 |
Issue |
11 |
Pages |
1194-1202 |
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
Abstract |
Results are presented of in situ studies of 1 MeV electron irradiation induced (113) defect generation in silicon containing different types and concentrations of extrinsic point defects. A semiquantitative model is developed describing the influence of interfaces and stress fields and of extrinsic point defects on the (113) defect generation in silicon during irradiation. The theoretical results obtained are correlated with experimental data obtained on silicon uniformly doped with boron and phosphorus and with observations obtained by irradiating cross-sectional samples of wafers with highly doped surface layers. It is shown that in situ irradiation in a high voltage election microscope is a powerful tool for studying local point defect reactions in silicon. (C) 1995 The Institute of Materials. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
Inst Materials |
Place of Publication |
London |
Editor |
|
Language |
|
Wos |
A1995TQ95100016 |
Publication Date |
2014-01-09 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0267-0836;1743-2847; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
0.995 |
Times cited |
7 |
Open Access |
|
Notes |
|
Approved |
no |
Call Number |
UA @ lucian @ c:irua:95911 |
Serial |
2654 |
Permanent link to this record |