|
“On the evolution of strain and electrical properties in as-grown and annealed Si:P epitaxial films for source-drain stressor applications”. Dhayalan SK, Kujala J, Slotte J, Pourtois G, Simoen E, Rosseel E, Hikavyy A, Shimura Y, Loo R, Vandervorst W, ECS journal of solid state science and technology 7, P228 (2018). http://doi.org/10.1149/2.0071805JSS
Abstract: Heavily P doped Si:P epitaxial layers have gained interest in recent times as a promising source-drain stressor material for n type FinFETs (Fin Field Effect Transistors). They are touted to provide excellent conductivity as well as tensile strain. Although the as-grown layers do provide tensile strain, their conductivity exhibits an unfavorable behavior. It reduces with increasing P concentration (P > 1E21 at/cm(3)), accompanied by a saturation in the active carrier concentration. Subjecting the layers to laser annealing increases the conductivity and activates a fraction of P atoms. However, there is also a concurrent reduction in tensile strain (<1%). Literature proposes the formation of local semiconducting Si3P4 complexes to explain the observed behaviors in Si:P [Z. Ye et al., ECS Trans., 50(9) 2013, p. 1007-10111. The development of tensile strain and the saturation in active carrier is attributed to the presence of local complexes while their dispersal on annealing is attributed to strain reduction and increase in active carrier density. However, the existence of such local complexes is not proven and a fundamental void exists in understanding the structure-property correlation in Si:P films. In this respect, our work investigates the reason behind the evolution of strain and electrical properties in the as-grown and annealed Si:P epitaxial layers using ab-initio techniques and corroborate the results with physical characterization techniques. It will be shown that the strain developed in Si:P films is not due to any specific complexes while the formation of Phosphorus-vacancy complexes will be shown responsible for the carrier saturation and the increase in resistivity in the as-grown films. Interstitial/precipitate formation is suggested to be a reason for the strain loss in the annealed films. (C) The Author(s) 2018. Published by ECS.
Keywords: A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Impact Factor: 1.787
Times cited: 4
DOI: 10.1149/2.0071805JSS
|
|
|
“Insights into the C Distribution in Si:C/Si:C:P and the Annealing Behavior of Si:C Layers”. Dhayalan SK, Nuytten T, Pourtois G, Simoen E, Pezzoli F, Cinquanta E, Bonera E, Loo R, Rosseel E, Hikavyy A, Shimura Y, Vandervorst W, ECS journal of solid state science and technology 8, P209 (2019). http://doi.org/10.1149/2.0181903JSS
Abstract: Si:C and Si:C:P alloys are potential candidates for source-drain stressor applications in n-type Fin Field Effect Transistors (FinFETs). Increasing the C content to achieve high strain results in the arrangement of C atoms as third nearest neighbors (3nn) in the Si: C lattice. During thermal annealing, the presence of C atoms as 3nn may promote clustering at the interstitial sites, causing loss of stress. The concentration of C atoms as 3nn is reduced by the incorporation of a small amount of Ge atoms during the growth, whereas in-situ P doping does not influence this 3nn distribution [J Solid State Sci. Technol vol 6, p 755, 2017]. Small amounts of Ge are provided during low temperature selective epitaxial growth scheme, which are based on cyclic deposition and etching (CDE). In this work, we aim to provide physical insights into the aforementioned phenomena, to understand the behavior of 3nn C atoms and the types of defects that are formed in the annealed Si: C films. Using ab-initio simulations, the Ge-C interaction in the Si matrix is investigated and this insight is used to explain how the Ge incorporation leads to a reduced 3nn distribution of the C atoms. The interaction between C and P in the Si: C: P films is also investigated to explain why the P incorporation has not led to a reduction in the 3nn distribution. We then report on the Raman characterization of Si: C layers subjected to post epi annealing. As the penetration depth of the laser is dependent on the wavelength, Raman measurements at two different wavelengths enable us to probe the depth distribution of 3nn C atoms after applying different annealing conditions. We observed a homogeneous loss in 3nn C throughout the layer. Whereas in the kinematic modeling of high resolution X-ray diffraction spectra, a gradient in the substitutional C loss was observed close to the epitaxial layer/substrate interface. This gradient can be due to the out diffusion of C atoms into the Si substrate or to the formation of interstitial C clusters, which cannot be distinguished in HR-XRD. Deep Level Transient Spectroscopy indicated that the prominent out-diffusing species was interstitial CO complex while the interstitial C defects were also prevalent in the epi layer. (c) 2019 The Electrochemical Society.
Keywords: A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Impact Factor: 1.787
DOI: 10.1149/2.0181903JSS
|
|
|
“Chemical and structural characterization of oxide precipitates in heavily boron doped silicon by infrared spectroscopy and transmission electron microscopy”. De Gryse O, Clauws P, Vanhellemont J, Lebedev O, van Landuyt J, Simoen E, Claeys C, , 183 (2002)
Abstract: Infrared absorption spectra of oxygen precipitates in boron doped silicon with a boron concentration between 10(17) and 10(19) cm(-3) are analyzed, applying the spectral function theory of the composite precipitates. The aspect ratio of the platelet precipitates has been determined by transmission electron microscopy measurements. Our analysis shows that in samples with moderate doping levels (<10(18) B cm(-3)) SiOgamma precipitates are formed with stoichiometry as in the lightly doped case. In the heavily (>10(18) cm(-3)) boron doped samples, however, the measured spectra of the precipitates are consistent with a mixture of SiO2 and B2O3. with a volume fraction of B2O3 as high as 0.41 in the most heavily doped case.
Keywords: P1 Proceeding; Electron microscopy for materials research (EMAT)
|
|
|
“Optical spectroscopy of oxygen precipitates in heavily doped p-type silicon”. Simoen E, Loo R, Claeys C, de Gryse O, Clauws P, van Landuyt J, Lebedev O, Journal of physics : condensed matter
T2 –, Conference on Extended Defects in Semiconductors (EDS 2002), JUN 01-06, 2002, BOLOGNA, ITALY 14, 13185 (2002). http://doi.org/10.1088/0953-8984/14/48/367
Abstract: Results are presented on the photoluminescence (PL) characterization of heavily doped p(+) Czochralski silicon, which has been subjected to a two-step, oxygen precipitation heat treatment. It will be shown that the presence of oxygen precipitates gives rise to the D1, D2 and D5 lines, where the energy of the D1 line shifts to lower values for a stronger degree of precipitation. The occurrence of these PL features is also a function of the boron concentration in the p(+) material. The PL results are compared with Fourier transform infrared absorption data and with transmission electron microscope, results. From this, it is concluded that PL has a good potential for use in the assessment of oxygen precipitation in heavily doped silicon.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 2.649
Times cited: 3
DOI: 10.1088/0953-8984/14/48/367
|
|
|
“A novel approach to analyse FTIR spectra of precipitates in boron-doped silicon”. de Gryse O, Vanhellemont J, Clauws P, Lebedev O, van Landuyt J, Simoen E, Claeys C, Physica: B : condensed matter
T2 –, 22nd International Conference on Defects in Semiconductors (ICDS-22), JUL 28-AUG 01, 2003, UNIV AARHUS, AARHUS, DENMARK 340, 1013 (2003). http://doi.org/10.1016/j.physb.2003.09.194
Abstract: Infrared absorption spectra of composite precipitates are analysed with a modified Day-Thorpe algorithm, assuming a precipitated phase consisting of a mixture of two components with known optical properties. Additional constraints are introduced when solving the model equations by using a priori knowledge making the algorithm more reliable. It is shown that this novel approach allows determining both morphology and composition of precipitates. The method is applied to characterise oxide precipitates in boron-doped silicon. The results indicate that for the resistivity range above 60 mOmegacm, the precipitated phase is most probably SiO1.17+/-0.14, while for resistivities below 20 mOmega cm, precipitates consist of a SiO2/B2O3 composite with a large volume fraction of B(2)0(3) (up to 40% for 8 mOmegacm material). (C) 2003 Elsevier B.V. All rights reserved.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 1.386
Times cited: 4
DOI: 10.1016/j.physb.2003.09.194
|
|
|
“Chemical and structural characterization of oxygen precipitates in silicon by infrared spectroscopy and TEM”. de Gryse O, Clauws P, Lebedev O, van Landuyt J, Vanhellemont J, Claeys C, Simoen E, Physica: B : condensed matter
T2 –, 21st International Conference on Defects in Semiconductors, JUL 16-20, 2001, GIESSEN, GERMANY 308, 294 (2001). http://doi.org/10.1016/S0921-4526(01)00801-8
Abstract: Infrared absorption spectra of polyhedral and platelet oxygen precipitates are analyzed using a modified Day-Thorpe approach (J. Phys.: Condens. Matter 11 (1999) 2551). The aspect ratio has been determined by TEM measurements. The reduced spectral function and the stoichiometry are extracted from the absorption spectra and the concentration of precipitated interstitial oxygen. One set of spectra reveal a Frohlich frequency around 1100 cm(-1) and another around 1110-1120 cm(-1). It is shown that the shift in the Frohlich frequency is not due to a different stoichiometry, but due to the detailed structure in the reduced spectral function. The oxygen precipitates consist of SiO. with gammaapproximate to1.1-1.2+/-0.1. (C) 2001 Elsevier Science B.V. All rights reserved.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 1.386
Times cited: 3
DOI: 10.1016/S0921-4526(01)00801-8
|
|
|
“InGaAs tunnel diodes for the calibration of semi-classical and quantum mechanical band-to-band tunneling models”. Smets Q, Verreck D, Verhulst AS, Rooyackers R, Merckling C, Van De Put M, Simoen E, Vandervorst W, Collaert N, Thean VY, Sorée B, Groeseneken G, Heyns MM;, Journal of applied physics 115, 184503 (2014). http://doi.org/10.1063/1.4875535
Abstract: Promising predictions are made for III-V tunnel-field-effect transistor (FET), but there is still uncertainty on the parameters used in the band-to-band tunneling models. Therefore, two simulators are calibrated in this paper; the first one uses a semi-classical tunneling model based on Kane's formalism, and the second one is a quantum mechanical simulator implemented with an envelope function formalism. The calibration is done for In0.53Ga0.47As using several p+/intrinsic/n+ diodes with different intrinsic region thicknesses. The dopant profile is determined by SIMS and capacitance-voltage measurements. Error bars are used based on statistical and systematic uncertainties in the measurement techniques. The obtained parameters are in close agreement with theoretically predicted values and validate the semi-classical and quantum mechanical models. Finally, the models are applied to predict the input characteristics of In0.53Ga0.47As n- and p-lineTFET, with the n-lineTFET showing competitive performance compared to MOSFET.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 2.068
Times cited: 34
DOI: 10.1063/1.4875535
|
|
|
“Electric-field induced quantum broadening of the characteristic energy level of traps in semiconductors and oxides”. Mohammed M, Verhulst AS, Verreck D, Van de Put M, Simoen E, Sorée B, Kaczer B, Degraeve R, Mocuta A, Collaert N, Thean A, Groeseneken G, Journal of applied physics 120, 245704 (2016). http://doi.org/10.1063/1.4972482
Abstract: The trap-assisted tunneling (TAT) current in tunnel field-effect transistors (TFETs) is one of the crucial factors degrading the sub-60 mV/dec sub-threshold swing. To correctly predict the TAT currents, an accurate description of the trap is required. Since electric fields in TFETs typically reach beyond 10(6) V/cm, there is a need to quantify the impact of such high field on the traps. We use a quantum mechanical implementation based on the modified transfer matrix method to obtain the trap energy level. We present the qualitative impact of electric field on different trap configurations, locations, and host materials, including both semiconductors and oxides. We determine that there is an electric-field related trap level shift and level broadening. We find that these electric-field induced quantum effects can enhance the trap emission rates. Published by AIP Publishing.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 2.068
Times cited: 6
DOI: 10.1063/1.4972482
|
|
|
“Oxide phase determination in silicon using infrared spectroscopy and transmission electron microscopy techniques”. Gryse OD, Clauws P, van Landuyt J, Lebedev O, Claeys C, Simoen E, Vanhellemont J, Journal of applied physics 91, 2493 (2002). http://doi.org/10.1063/1.1429800
Abstract: Infrared absorption spectra of polyhedral and platelet oxygen precipitates in silicon are analyzed using a modified Day-Thorpe approach [J. Phys.: Condens. Matter 11, 2551 (1999)]. The aspect ratio of the precipitates is determined by transmission electron microscopy analysis. The reduced spectral function and the stoichiometry of the precipitate are extracted from the absorption spectra and the amount of precipitated interstitial oxygen. The experimental absorption spectra can be divided in a set with a Frohlich frequency of around 1100 cm(-1) and in a set with a Frohlich frequency between 1110 and 1120 cm(-1). It is shown that the shift in the Frohlich frequency is not due to a differing stoichiometry, but to the detailed structure of the reduced spectral function. Inverse modeling of the spectra suggests that the oxide precipitates consist of substoichiometric SiOgamma with gamma=1.17+/-0.14. (C) 2002 American Institute of Physics.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 2.068
Times cited: 27
DOI: 10.1063/1.1429800
|
|
|
“Characterization of oxide precipitates in heavily B-doped silicon by infrared spectroscopy”. de Gryse O, Clauws P, Vanhellemont J, Lebedev OI, van Landuyt J, Simoen E, Claeys C, Journal of the electrochemical society 151, G598 (2004). http://doi.org/10.1149/1.1776592
Abstract: Infrared absorption spectra of oxygen precipitates in boron-doped silicon with a boron concentration between 10(17) and 10(19) cm(-3) are analyzed, applying the spectral function representation of composite materials. The aspect ratio of the platelet precipitates is determined by transmission electron microscopy measurements. The analysis shows that in samples with moderate doping levels (<10(18) B cm(-3)) SiOγ precipitates are formed with the same composition as in the lightly doped case. In the heavily boron-doped (>10(18) cm(-3)) samples, however, the measured spectra of the precipitates are consistent with a mixture of SiO2 and B2O3, with a volume fraction of B2O3 as high as 0.41 in the most heavily doped case. (C) 2004 The Electrochemical Society.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 3.259
Times cited: 13
DOI: 10.1149/1.1776592
|
|
|
“On the manifestation of phosphorus-vacancy complexes in epitaxial Si:P films”. Dhayalan SK, Kujala J, Slotte J, Pourtois G, Simoen E, Rosseel E, Hikavyy A, Shimura Y, Iacovo S, Stesmans A, Loo R, Vandervorst W;, Applied physics letters 108, 082106 (2016). http://doi.org/10.1063/1.4942605
Abstract: In situ doped epitaxial Si: P films with P concentrations > 1 x 10(21) at./cm(3) are suitable for source-drain stressors of n-FinFETs. These films combine the advantages of high conductivity derived from the high P doping with the creation of tensile strain in the Si channel. It has been suggested that the tensile strain developed in the Si: P films is due to the presence of local Si3P4 clusters, which however do not contribute to the electrical conductivity. During laser annealing, the Si3P4 clusters are expected to disperse resulting in an increased conductivity while the strain reduces slightly. However, the existence of Si3P4 is not proven. Based on first-principles simulations, we demonstrate that the formation of vacancy centered Si3P4 clusters, in the form of four P atoms bonded to a Si vacancy, is thermodynamically favorable at such high P concentrations. We suggest that during post epi-growth annealing, a fraction of the P atoms from these clusters are activated, while the remaining part goes into interstitial sites, thereby reducing strain. We corroborate our conjecture experimentally using positron annihilation spectroscopy, electron spin resonance, and Rutherford backscattering ion channeling studies. (C) 2016 AIP Publishing LLC.
Keywords: A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Impact Factor: 3.411
Times cited: 9
DOI: 10.1063/1.4942605
|
|