|
“Microstructure of artificial [100] 45°, twist grain boundaries in YBa2Cu3O7-”. Verbist K, Tafuri F, Miletto Granozio F, di Chiara S, Van Tendeloo G, Electron microscopy: vol. 2 , 593 (1998)
Keywords: A3 Journal article; Electron microscopy for materials research (EMAT)
|
|
|
“Modeling of bombardment induced oxidation of silicon with and without oxygen flooding”. de Witte H, Vandervorst W, Gijbels R, , 327 (1998)
Keywords: P3 Proceeding; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
|
|
|
“'Natural' and 'man-made' platelets in type-la diamonds”. Kiflawi I, Bruley J, Luyten W, Van Tendeloo G, Philosophical magazine: B: physics of condensed matter: electronic, optical and magnetic properties 78, 299 (1998). http://doi.org/10.1080/13642819808205733
Abstract: 'Natural' platelets are planar defects in {001} planes found in natural type-IaA/B diamonds. 'Man-made' platelets are platelets formed in the laboratory by annealing type-IaA diamonds at temperatures over 2500 degrees C. Careful study shows that the infrared (IR) spectra of the 'man-made' platelets are different from the IR spectra of 'natural' platelets. High-temperature (T greater than or equal to 2000 degrees C) annealing of platelets containing type-IaA/B diamonds modifies the IR absorption spectrum owing to the 'natural' platelets and makes it similar to the IR spectrum of the 'man-made' platelets. It is suggested that such high-temperature annealing changes the structure of the 'natural' platelets. The changes are too subtle to be detected by electron microscopy techniques. Topographic electron-energy-loss spectroscopy shows that platelets contain nitrogen at an average density of 0.7 atoms per a(0)(2); however, high-temperature annealing does not seem to affect the concentration of the nitrogen in the platelets.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Times cited: 13
DOI: 10.1080/13642819808205733
|
|
|
“On the mechanism of {111}-defect formation in silicon studies by in situ electrin irradiation in a high resolution electron microscope”. Fedina L, Gutakovskii A, Aseev A, van Landuyt J, Vanhellemont J, Philosophical magazine: A: physics of condensed matter: defects and mechanical properties 77, 423 (1998)
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Times cited: 23
|
|
|
“Phase boundaries of superconducting mesoscopic square loops”. Fomin VM, Misko VR, Devreese JT, Moshchalkov VV, 249/251, 476 (1998)
Keywords: A1 Journal article; Electron Microscopy for Materials Science (EMAT);
|
|
|
“Precipitation behavior in Cu-Co alloy”. Takeda M, Shinohara G, Yamada H, Yoshida S, van Landuyt J, Hashimoto H, , 205 (1998)
Keywords: P3 Proceeding; Electron microscopy for materials research (EMAT)
|
|
|
“Preparation of nanocrystalline titania powder by aerosol pyrolysis of titanium alkoxide”. Ahonen PP, Kauppinen EI, Deschanvres JL, Joubert JC, Van Tendeloo G, Materials Research Society symposium proceedings 520, 109 (1998)
Keywords: P1 Proceeding; Electron microscopy for materials research (EMAT)
Times cited: 2
|
|
|
“Proton tunneling and nonlinear polarizability effects in hydrogen-bonded ferroelectrics”. Bussmann-Holder A, Michel KH, AIP conference proceedings
T2 –, 5th Williamsburg Workshop on 1st-Principles Calculations for, Ferroelectrics, FEB 01-04, 1998, WILLIAMSBURG, VA , 202 (1998)
Abstract: Hydrogen-bonded ferroelectrics are modelled by a coupled spin/nonlinear lattice (polarizability) interaction Hamiltonian, where specifically the geometry of the hydrogen bond is included. The model leads to a structural phase transition and describes correctly the isotope effect due to the substitution H/D in hydrogen-bonded systems in terms of bond length changes.
Keywords: P1 Proceeding; Condensed Matter Theory (CMT)
|
|
|
“Purification of catalytically produced multi-wall nanotubes”. Colomer J-F, Piedigrosso P, Willems I, Journet C, Bernier P, Van Tendeloo G, Fonseca A, Nagy JB, Journal of the Chemical Society : Faraday transactions: physical chemistry and chemical physics 94, 3753 (1998). http://doi.org/10.1039/a806804f
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Times cited: 92
DOI: 10.1039/a806804f
|
|
|
“Quantitative analysis of individual AgxAuy nanoparticles by TEM-EDX: track 1”. de Vyt A, Gijbels R, van Roost C, Geuens I, , 524 (1998)
Keywords: P3 Proceeding; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
|
|
|
“Quantitative SIMS analysis of surface layers of cubic silver halide microcrystals: comparison of different quantification methods”. Verlinden G, Gijbels R, Geuens I, , 995 (1998)
Keywords: P3 Proceeding; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
|
|
|
“Reduced dimensionality in different forms of carbon”. Van Tendeloo G, Bernaerts D, Amelinckx S, Fullerenes and carbon based materials , 487 (1998)
Abstract: Several TEM techniques are used to characterise the local structure of low dimensional forms of carbon. HREM is particularly useful to describe the defect structure of thin films of diamond or fullerenes and C-60-C-70 nanoclusters. A columnar form of graphite is analysed, mainly by electron diffraction which allowed us to propose a growth mechanism. Diffraction contrast dark field microscopy, in combination with electron diffraction, allows a detailed characterisation of carbon nanotubes; e.g. the chirality distribution of tubes in ropes of single wall tubes is studied by selected area electron diffraction. (C) 1998 Elsevier Science Ltd. All rights reserved.
Keywords: P1 Proceeding; Electron microscopy for materials research (EMAT)
|
|
|
“Reduction of composite Ag(Br,I) grains as studied by AEM and digital image analysis techniques”. Oleshko VP, Gijbels RH, Jacob WA, , 657 (1998)
Keywords: P1 Proceeding; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
|
|
|
“Scanning microanalysis”. Gijbels R, Oleshko V s.l., page 427 (1998).
Keywords: H3 Book chapter; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
|
|
|
“Structural and analytical characterization of Ag(Br,I) nanocrystals by cryo-AEM techniques”. Oleshko VP, van Daele A, Gijbels RH, Jacob WA, Journal of nanostructured materials 10, 1225 (1998). http://doi.org/10.1016/S0965-9773(99)00003-3
Keywords: A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Times cited: 5
DOI: 10.1016/S0965-9773(99)00003-3
|
|
|
“Structural and analytical characterization of composite tabular silver halide microcrystals by cryo-EFTEM/EELS and cryo-STEM/EDX techniques”. Oleshko VP, Gijbels RH, Jacob WA, van Daele AJ Antwerp, page 317 (1998).
Keywords: H3 Book chapter; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
|
|
|
“Structure and magnetotransport properties of La2/3Ca1/3MnO3 thin films prepared by pulsed laser deposition”. Lebedev OI, Van Tendeloo G, Amelinckx S, Leibold B, Habermeier HU, Phillipp F, Materials Research Society symposium proceedings
T2 –, Symposium on Advances in Laser Ablation of Materials at the 1998 MRS, Spring Meeting, April 13-16, 1998, San Francisco, Calif. , 219 (1998). http://doi.org/10.1557/PROC-526-219
Abstract: La1-xCaxMnO3-delta (LCMO) thin films are grown by pulsed laser deposition on a (100) SrTiO3 substrate at temperatures between 530 degrees C and 890 degrees C. The magnetotransport properties show a high negative magnetoresistance and a shift of the maximum of the R(T) curve as function of temperature. The Curie temperature changes with deposition temperature and film quality in the range of 100-220K. The film quality is characterised by X-ray diffraction and transmission electron microscopy (TEM); film and target compositions were verified by atomic emission spectroscopy. The local structure of the film depends on the growth conditions and substrate temperature. TEM reveals a slight distortion of the film leading to a breakdown of the symmetry from orthorhombic to monoclinic. At the highest growth temperatures, a well defined interface is observed within the LCMO film, parallel to the substrate surface; this interface divides the film into two lamellae with a different microstructure. The lamella close to the substrate is perfectly coherent with the substrate, suggesting that it is strained as a result of the lattice parameter mismatch; the upper lamella shows a typical domain structure with unusual translation interfaces characterised by a displacement vector of the type 1/2[010](m) and 1/2[001](m) when referred ten the monoclinic lattice.
Keywords: P1 Proceeding; Electron microscopy for materials research (EMAT)
DOI: 10.1557/PROC-526-219
|
|
|
“Structure of Y123 and Y247 fluorinated phases by HREM”. Lebedev OI, Van Tendeloo G, Abakumov AM, Shpanchenko RV, Rozova MG, Antipov EV, Electron microscopy: vol. 3 , 297 (1998)
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
|
|
|
“Study of electron excitations in Ag(Br,I) nanocrystals by cryo-AEM techniques”. Oleshko VP, van Daele AJ, Gijbels RH, Jacob WA, , 659 (1998)
Keywords: P1 Proceeding; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
|
|
|
“Study of the thermal decomposition of melt-quenched Ni-rich metastable bcc and amorphous Ni-Zr alloys”. Cziraki A, Gerocs I, Fogarassy B, Van Tendeloo G, Sommer F, Bakonyi I, International journal of non-equilibrium processing 10, 265 (1998)
Abstract: The phase transformation sequences during thermal decomposition are investigated for Ni-rich melt-quenched body-centred cubic (bcc) and amorphous Ni-Zr alloys. Transmission electron microscopy (TEM) and X-ray diffraction (XRD) are used to determine the structure of crystallization products occurring after heating the melt-spun ribbon samples to various degrees of the phase transformation process monitored by differential scanning calorimetry (DSC). A single DSC peak is observed for both the bcc and amorphous Ni(91)Zr(9) alloys and a two-step process is indicated by DSC for the amorphous Ni(90)Zr(10) alloy. In the bcc-Ni(91)Zr(9) alloy which is actually a Ni(Zr) solid solution phase, the phase transformation starts with the precipitation of Ni(5)Zr crystallites followed, after a sufficient depletion of the matrix in Zr, by the subsequent transformation of the bcc-Ni(Zr) lattice to face-centred cubic (fcc) Ni. In the amorphous alloy of the same composition, the final products are fcc-Ni and Ni(5)Zr but at intermediate stages of the phase transformation, bcc-Ni(Zr) crystallites also appear. In the a-Ni(90)Zr(10) alloy the first DSC peak corresponds to the formation of the bcc-Ni(Zr) phase which then decomposes (second DSC peak) to the equilibrium phases fcc-Ni and Ni(5)Zr. Thus, in addition to the previous observation of the formation of the metastable bcc-Ni(Zr) phase by rapid quenching from the melt, here we present evidence that this phase can form also after partial crystallization of metallic glasses of appropriate chemical compositions.
Keywords: A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
Times cited: 2
|
|
|
“Superconducting mesoscopic square loops: phase boundaries and magnetization”. Devreese JT, Fomin VM, Misko VR, Moshchalkov VV, 1/2, 33 (1998)
Keywords: A1 Journal article; Electron Microscopy for Materials Science (EMAT);
Times cited: 1
|
|
|
“Surface analysis of halide distributions in complex AgX microcrystals by imaging time-of-flight SIMS (TOF-SIMS)”. Verlinden G, Gijbels R, Geuens I, de Keyzer R Antwerp, page 528 (1998).
Keywords: H3 Book chapter; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
|
|
|
“TEM study on precipitation behavior in Cu-Co alloys”. Takeda M, Suzuki N, Shinohara G, Endo T, van Landuyt J, Physica status solidi: A: applied research 168, 27 (1998). http://doi.org/10.1002/(SICI)1521-396X(199807)168:1<27::AID-PSSA27>3.0.CO;2-S
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Times cited: 18
DOI: 10.1002/(SICI)1521-396X(199807)168:1<27::AID-PSSA27>3.0.CO;2-S
|
|
|
“Een tempel voor elektronenmicroscopie “kijken naar atomen””. van Landuyt J, Fonds informatief 38, 13 (1998)
Keywords: A3 Journal article; Electron microscopy for materials research (EMAT)
|
|
|
“Preparation and characterization of melt textured NdBa2Cu3O7- bulk superconducting ceramics”. Tancret F, Monot I, Laffez P, Van Tendeloo G, Desgardin G, European physical journal: applied physics 1, 185 (1998). http://doi.org/10.1051/epjap:1998135
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 0.684
Times cited: 2
DOI: 10.1051/epjap:1998135
|
|
|
“The isotope effect in hydrogen-bonded systems”. Bussmann-Holder A, Michel KH, International journal of modern physics: B: condensed matter physics, statistical physics, applied physics
T2 –, 1st International Conference on New Theories, Discoveries, and, Applications of Superconductors and Related Materials (New3SC-1), FEB 19-24, 19 12, 3406 (1998). http://doi.org/10.1142/S021797929800274X
Abstract: The giant isotope effect on the ferro- and antiferroelectric transition temperature upon deuteration of hydrogen-bonded systems is well known experimentally since various decades. Yet, theoretically only recently a microscopic understanding of this effect has been achieved which, specifically, took into account the geometry of the O ... H ... O bond. The implications of this modeling are multiple as numerous hydrogen-bonded organic systems show the same effects as ferro- and antiferroelectrics, i.e., cooperative proton tunneling at a well-defined temperature.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 0.736
DOI: 10.1142/S021797929800274X
|
|
|
“Modulated structures in KAISi3O8: a study by high resolution electron microscopy and 29Si MAS-NMR spectroscopy”. Sanchez-Munoz L, Nistor L, Van Tendeloo G, Sanz J, Journal of electron microscopy 47, 17 (1998). http://doi.org/10.1093/oxfordjournals.jmicro.a023555
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 0.9
Times cited: 10
DOI: 10.1093/oxfordjournals.jmicro.a023555
|
|
|
“A new model for the (2x1) reconstructed CoSi2-Si(100) interface”. Buschmann V, Fedina L, Rodewald M, Van Tendeloo G, Philosophical magazine letters 77, 147 (1998). http://doi.org/10.1080/095008398178589
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 0.941
Times cited: 10
DOI: 10.1080/095008398178589
|
|
|
“Voidites in polycrystalline natural diamond”. Chen JH, Bernaerts D, Seo JW, Van Tendeloo G, Kagi H, Philosophical magazine letters 77, 135 (1998). http://doi.org/10.1080/095008398178561
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 0.941
Times cited: 7
DOI: 10.1080/095008398178561
|
|
|
“Comprehensive three-dimensional modeling network for a dc glow discharge plasma”. Bogaerts A, Gijbels R, Plasma physics reports 24, 573 (1998)
Keywords: A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Impact Factor: 0.984
Times cited: 8
|
|