|
“Selective recovery of Cr from stainless steel slag by alkaline roasting followed by water leaching”. Kim E, Spooren J, Broos K, Horckmans L, Quaghebeur M, Vrancken KC, Hydrometallurgy 158, 139 (2015). http://doi.org/10.1016/J.HYDROMET.2015.10.024
Abstract: Selective chromium (Cr) leaching from stainless steel slag (SS slag) by alkali roasting followed by water leaching was investigated. The efficiency of the alkali roasting process for Cr leaching was increased by optimizing the mass ratio of alkaline agents (NaOH, and NaOH-NaNO3) to the slag, roasting temperature and time. At the optimum condition (0.67 mass ratio of NaOH to SS slag, 400 degrees C, 2 h) of NaOH roasting, chromium leaching was around 83%, while the matrix material was dissolved only to a limited extent (Si 8.0%). Mechanical activation of the SS slag prior to roasting reduced the optimum NaOH to SS slag mass ratio to 0.4. The addition of NaNO3 as an oxidant to the NaOH salt increased Cr leaching to 89% after roasting at 400 degrees C for 2 h. The remaining Cr phases in the residue were almost exclusively FeCr alloys. Further chromium dissolution from these alloys is prevented by a passivation layer of Fe oxides as shown by SEM/EDS images. Based on these results, a SS slag recycling process is suggested in which roasting-water leaching followed by water washing to remove Cr yields a residue which has potential for application as a construction material. (C) 2015 Elsevier B.V. All rights reserved.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1016/J.HYDROMET.2015.10.024
|
|
|
“Self-inhibition can limit biologically enhanced TCE dissolution from a TCE DNAPL”. Haest PJ, Springael D, Seuntjens P, Smolders E, Chemosphere 89, 1369 (2012). http://doi.org/10.1016/J.CHEMOSPHERE.2012.05.097
Abstract: Biodegradation of trichloroethene (TCE) near a Dense Non Aqueous Phase Liquid (DNAPL) can enhance the dissolution rate of the DNAPL by increasing the concentration gradient at the DNAPL-water interface. Two-dimensional flow-through sand boxes containing a ICE DNAPL and inoculated with a TCE dechlorinating consortium were set up to measure this bio-enhanced dissolution under anaerobic conditions. The total mass of TCE and daughter products in the effluent of the biotic boxes was 3-6 fold larger than in the effluent of the abiotic box. However, the mass of daughter products only accounted for 19-55% of the total mass of chlorinated compounds in the effluent, suggesting that bio-enhanced dissolution factors were maximally 1.3-2.2. The enhanced dissolution most likely primarily resulted from variable DNAPL distribution rather than biodegradation. Specific dechlorination rates previously determined in a stirred liquid medium were used in a reactive transport model to identify the rate limiting factors. The model adequately simulated the overall TCE degradation when predicted resident microbial numbers approached observed values and indicated an enhancement factor for TCE dissolution of 1.01. The model shows that dechlorination of TCE in the 20 box was limited due to the short residence time and the self-inhibition of the TCE degradation. A parameter sensitivity analysis predicts that the bio-enhanced dissolution factor for this TCE source zone can only exceed a value of 2 if the TCE self-inhibition is drastically reduced (when a TCE tolerant dehalogenating community is present) or if the DNAPL is located in a low-permeable layer with a small Darcy velocity. (C) 2012 Elsevier Ltd. All rights reserved.
Keywords: A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1016/J.CHEMOSPHERE.2012.05.097
|
|
|
“Sensitivity of water stress in a two-layered sandy grassland soil to variations in groundwater depth and soil hydraulic parameters”. Rezaei M, Seuntjens P, Joris I, Boenne W, Van Hoey S, Campling P, Cornelis WM, Hydrology and earth system sciences 20, 487 (2016). http://doi.org/10.5194/HESS-20-487-2016
Abstract: Monitoring and modelling tools may improve irrigation strategies in precision agriculture. We used non-invasive soil moisture monitoring, a crop growth and a soil hydrological model to predict soil water content fluctuations and crop yield in a heterogeneous sandy grassland soil under supplementary irrigation. The sensitivity of the soil hydrological model to hydraulic parameters, water stress, crop yield and lower boundary conditions was assessed after integrating models. Free drainage and incremental constant head conditions were implemented in a lower boundary sensitivity analysis. A time-dependent sensitivity analysis of the hydraulic parameters showed that changes in soil water content are mainly affected by the soil saturated hydraulic conductivity K-s and the Mualem-van Genuchten retention curve shape parameters n and alpha. Results further showed that different parameter optimization strategies (two-, three-, four- or six-parameter optimizations) did not affect the calculated water stress and water content as significantly as does the bottom boundary. In this case, a two-parameter scenario, where K-s was optimized for each layer under the condition of a constant groundwater depth at 135-140 cm, performed best. A larger yield reduction, and a larger number and longer duration of stress conditions occurred in the free drainage condition as compared to constant boundary conditions. Numerical results showed that optimal irrigation scheduling using the aforementioned water stress calculations can save up to 12-22 % irrigation water as compared to the current irrigation regime. This resulted in a yield increase of 4.5-6.5 %, simulated by the crop growth model.
Keywords: A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.5194/HESS-20-487-2016
|
|
|
“Short and long term effect of decreasing temperature on anammox activity and enrichment in mainstream granular sludge process”. De Cocker P, Bessiere Y, Hernandez-Raquet G, Dubos S, Mercade M, Sun XY, Mozo I, Barillon B, Gaval G, Caligaris M, Martin Ruel S, Vlaeminck SE, Sperandio M, 4, 50 (2017). http://doi.org/10.1007/978-3-319-58421-8_8
Abstract: This study investigates the impact of lower temperature on short term and long term (down to 10 degrees C) on a completely anoxic anammox granular sludge process. This is the first time granular sludge Anammox is operated in pure anoxic condition in SBR and at low temperature. Conversion performance, kinetic parameters, sludge characteristics and microbial community were analyzed.
Keywords: P1 Proceeding; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1007/978-3-319-58421-8_8
|
|
|
“Short and long term effect of decreasing temperature on anammox activity and enrichment in mainstream granular sludge process”. De Cocker P, Bessiere Y, Hernandez-Raquet G, Dubos S, Mercade M, Sun XY, Mozo I, Barillon B, Gaval G, Caligaris M, Ruel SM, Vlaeminck SE, Sperandio M, Frontiers In Wastewater Treatment And Modelling, Ficwtm 2017 4, 50 (2017). http://doi.org/10.1007/978-3-319-58421-8_8
Abstract: This study investigates the impact of lower temperature on short term and long term (down to 10 degrees C) on a completely anoxic anammox granular sludge process. This is the first time granular sludge Anammox is operated in pure anoxic condition in SBR and at low temperature. Conversion performance, kinetic parameters, sludge characteristics and microbial community were analyzed.
Keywords: P1 Proceeding; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1007/978-3-319-58421-8_8
|
|
|
“Sidestream deammonification on thermal hydrolysis process digestate : strategies to overcome nitritation inhibition”. Zhang Q, De Clippeleir H, Al-Omari A, Wett B, Vlaeminck SE, Murthy S, , 11 p.
T2 (2015)
Keywords: P3 Proceeding; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
|
|
|
“Size resolved ultrafine particles emission model : a continues size distribution approach”. Nikolova I, Janssen S, Vrancken K, Vos P, Mishra V, Berghmans P, The science of the total environment 409, 3492 (2011). http://doi.org/10.1016/J.SCITOTENV.2011.05.015
Abstract: A new parameterization for size resolved ultrafine particles (UFP) traffic emissions is proposed based on the results of PARTICULATES project (Samaras et al., 2005). It includes the emission factors from the Emission Inventory Guidebook (2006) (total number of particles, #/km/veh), the shape of the corresponding particle size distribution given in PARTICULATES and data for the traffic activity. The output of the model UFPEM (UltraFine Particle Emission Model) is a sum of continuous distributions of ultrafine particles emissions per vehicle type (passenger cars and heavy duty vehicles), fuel (petrol and diesel) and average speed representative for urban, rural and highway driving. The results from the parameterization are compared with measured total number of ultrafine particles and size distributions in a tunnel in Antwerp (Belgium). The measured UFP concentration over the entire campaign shows a close relation to the traffic activity. The modelled concentration is found to be lower than the measured in the campaign. The average emission factor from the measurement is 4.29E + 14 #/km/veh whereas the calculated is around 30% lower. A comparison of emission factors with literature is done as well and in overall a good agreement is found. For the size distributions it is found that the measured distributions consist of three modes Nucleation, Aitken and accumulation and most of the ultrafine particles belong to the Nucleation and the Aitken modes. The modelled Aitken mode (peak around 0.040.05 μm) is found in a good agreement both as amplitude of the peak and the number of particles whereas the modelled Nucleation mode is shifted to smaller diameters and the peak is much lower that the observed. Time scale analysis shows that at 300 m in the tunnel coagulation and deposition are slow and therefore neglected. The UFPEM emission model can be used as a source term in dispersion models.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1016/J.SCITOTENV.2011.05.015
|
|
|
“Smart operation of nitritation/denitritation virtually abolishes nitrous oxide emission during treatment of co-digested pig slurry centrate”. Peng L, Carvajal-Arroyo JM, Seuntjens D, Prat D, Colica G, Pintucci C, Vlaeminck SE, Water research 127, 1 (2017). http://doi.org/10.1016/J.WATRES.2017.09.049
Abstract: The implementation of nitritation/denitritation (Nit/DNit) as alternative to nitrification/denitrification (N/DN) is driven by operational cost savings, e.g. 1.0-1.8 EUR/ton slurry treated. However, as for any biological nitrogen removal process, Nit/DNit can emit the potent greenhouse gas nitrous oxide (N2O). Challenges remain in understanding formation mechanisms and in mitigating the emissions, particularly at a low ratio of organic carbon consumption to nitrogen removal (CODrem/N-rem). In this study, the centrate (centrifuge supernatant) from anaerobic co-digestion of pig slurry was treated in a sequencing batch reactor. The process removed approximately 100% of ammonium a satisfactory nitrogen loading rate (0.4 g N/L/d), with minimum nitrite and nitrate in the effluent. Substantial N2O emission (around 17% of the ammonium nitrogen loading) was observed at the baseline operational condition (dissolved oxygen, DO, levels averaged at 0.85 mg O-2/L; CODrem/N-rem of 2.8) with similar to 68% of the total emission contributed by nitritation. Emissions increased with higher nitrite accumulation and lower organic carbon to nitrogen ratio. Yet, higher DO levels (similar to 2.2 mg O-2/L) lowered the aerobic N2O emission and weakened the dependency on nitrite concentration, suggesting a shift in N2O production pathway. The most effective N2O mitigation strategy combined intermittent patterns of aeration, anoxic feeding and anoxic carbon dosage, decreasing emission by over 99% (down to similar to 0.12% of the ammonium nitrogen loading). Without anaerobic digestion, mitigated Nit/DNit decreases the operational carbon footprint with about 80% compared to N/DN. With anaerobic digestion included, about 4 times more carbon is sequestered. In conclusion, the low CODrem/N-rem feature of Nit/DNit no longer offsets its environmental sustainability provided the process is smartly operated. (c) 2017 Elsevier Ltd. All rights reserved.
Keywords: A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1016/J.WATRES.2017.09.049
|
|
|
“Solubilization of struvite as a sustainable nutrient source for single cell protein production”. Muys M, Derese S, Verliefde A, Vlaeminck SE, Communications in agricultural and applied biological sciences 81, 179 (2016)
Abstract: By 2050, the world population will have considerably expanded and the life standard of many will increase, yielding a 50% higher demand in protein (FAO, 2011), and even increases of 82 and 102% for diary and meat products, respectively (Boland et al., 2013). To provide in this increasing demand we are highly dependent on our classical fertilizer to food chain which has a high environmental impact and lacks efficiency. Nutrient losses cause eutrophication and biodiversity loss and the input of resources is already beyond the boundaries of environmental sustainability (Steffen et al., 2015). Phosphate fertilizers are made from phosphate rock (apatite), of which the reserves are predicted to be depleted within 50 100 years if we continue business as usual (Cordell et al., 2009). Next to problems related to the unbalanced geopolitical distribution with dominance in China and Morocco, the decreasing quality of the remaining apatite will result in an increasing environmental impact of fertilizer production. Finally, our traditional food production model requires 30% of all ice-free land, 70% of all available freshwater and produces up to one third of the global greenhouse gas emission, of which 80 to 86% is linked to agricultural production (Vermeulen et al., 2012). To ensure food security, nutrient recovery from waste streams can provide an important strategy. In this context, struvite ( ) crystallisation may be applied to recover phosphorus, along with some nitrogen. Reusing these nutrients as agricultural fertilizer on the field will lead to considerable losses to the environment. In contrast, their use to cultivate micro-organisms, e.g. for single cell protein (SCP), offers to potential of a near perfect conversion efficiency (Moed et al., 2015). At this moment, microalgae represent the most developed type of SCP, and are a promising protein source due to their growth rate, high nutritional quality and extremely high nutrient usage efficiency (Becker, 2007). Reliable solubilisation data are essential to design a technological strategy for struvite dosage in bioreactors for SCP production. The effect on solubility and solubilisation rate of relevant physicochemical parameters was studied experimentally in aqueous solutions. Because pH and temperature greatly affect solubilisation kinetics they were set at a constant value of 7 and 20°C respectively. The effect of some parameters on struvite solubility was already studied (Bhuiyan et al., 2007; Ariyanto et al., 2014; Roncal-Herrero and Oelkers, 2011), but solubilisation rates were not yet considered and pH was not controlled at a constant value. The chemical parameters considered in this study include the concentration of different common ions ( and ), foreign ions ( and the chelating agent ethylenediaminetetraacetic acid, EDTA) present in micro-algal cultivation media as well as ionic strength (as set by NaCl). The main physical parameter included was contact surface, through variation in initial particle size and as well as in struvite dosage concentration.
Keywords: A2 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
|
|
|
“Some like it hot : perspectives for thermophilic nitrogen removal”. Vlaeminck SE, Courtens ENP, Vandekerckhove TGL, Boon N, , 4 p.
T2 (2015)
Keywords: P3 Proceeding; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
|
|
|
“Some properties of “bulky&rdquo, links, generated by Generalized Möbius Listing's bodies GML4n”. Caratelli D, Gielis J, Ricci PE, Tavkhelidze I, Journal of mathematical sciences 216, 509 (2016). http://doi.org/10.1007/S10958-016-2907-X
Abstract: In the present paper, we consider the bulky knots and bulky links that appear after cutting of generalized MöbiusListing GML 4 n bodies (with corresponding radial cross sections square) along different generalized MöbiusListing surfaces GML 2 n situated in it. The aim of this article is to examine the number and geometric structure of independent objects that appear after such a cutting process of GML 4 n bodies. In most cases, we are able to count the indices of the resulting mathematical objects according to the known tabulation for knots and links of small complexity.
Keywords: A2 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1007/S10958-016-2907-X
|
|
|
“Some properties of “bulky&rdquo, links, generated by Generalized Möbius Listing's bodies GML4n”. Caratelli D, Gielis J, Ricci PE, Tavkhelidze I, (2013)
Keywords: P3 Proceeding; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
|
|
|
“Space-time information analysis for resource-conscious urban planning and design : a stakeholder based identification of urban metabolism data gaps”. Voskamp IM, Spiller M, Stremke S, Bregt AK, Vreugdenhil C, Rijnaarts HHM, Resources, conservation and recycling 128, 516 (2018). http://doi.org/10.1016/J.RESCONREC.2016.08.026
Abstract: The research presented here examined at which spatial and temporal resolution urban metabolism should be analysed to generate results that are useful for implementation of urban planning and design interventions aiming at optimization of resource flows. Moreover, it was researched whether a lack of data currently hampers analysing resource flows at this desired level of detail. To facilitate a stakeholder based research approach, the SIRUP tool Space-time Information analysis for Resource-conscious Urban Planning was developed. The tool was applied in a case study of Amsterdam, focused on the investigation of energy and water flows. Results show that most urban planning and design interventions envisioned in Amsterdam require information on a higher spatiotemporal resolution than the resolution of current urban metabolism analyses, i.e., more detailed than the city level and at time steps smaller than a year. Energy-related interventions generally require information on a higher resolution than water-related interventions. Moreover, for the majority of interventions information is needed on a higher resolution than currently available. For energy, the temporal resolution of existing data proved inadequate, for water, data with both a higher spatial and temporal resolution is required. Modelling and monitoring techniques are advancing for both water and energy and these advancements are likely to contribute to closing these data gaps in the future. These advancements can also prove useful in developing new sorts of urban metabolism analyses that can provide a systemic understanding of urban resource flows and that are tailored to urban planning and design.
Keywords: A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1016/J.RESCONREC.2016.08.026
|
|
|
“Spherical harmonic solution of the Robin problem for the Helmholtz equation in a supershaped shell”. Caratelli D, Gielis J, Tavkhelidze I, Ricci PE, Applied mathematics 4, 263 (2013). http://doi.org/10.4236/AM.2013.41A040
Abstract: The Robin problem for the Helmholtz equation in normal-polar shells is addressed by using a suitable spherical harmonic expansion technique. Attention is in particular focused on the wide class of domains whose boundaries are defined by a generalized version of the so-called superformula introduced by Gielis. A dedicated numerical procedure based on the computer algebra system Mathematica? is developed in order to validate the proposed methodology. In this way, highly accurate approximations of the solution, featuring properties similar to the classical ones, are obtained.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.4236/AM.2013.41A040
|
|
|
“Startup strategies of deammonification reactors treating reject water from thermally hydrolyzed solids”. Zhang Q, Vlaeminck SE, DeBarbadillo C, Suzuki R, Kharkar SM, Al-Omari A, Wett B, Chandran K, Murthy S, De Clippeleir H, , 5 p.
T2 (2017)
Keywords: P3 Proceeding; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
|
|
|
“Structure of the dm knives and process of cutting of GML(man) or GRT(man) bodies”. Tavkhelidze I, Gielis J, Sn –, 1512-0066 33 (2019)
Keywords: A3 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
|
|
|
“Struvite and organic fertilizer impacting the rhizosphere microbial community, nutrient turnover and plant growth performance”. Grunert O, Robles Aguilar AA, Hernandez-Sanabria E, Vandekerckhove T, Reheul D, Van Labeke M-C, Vlaeminck S, Boon N, Jablonowski ND, , 12 p.
T2 (2016)
Keywords: P3 Proceeding; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
|
|
|
“Struvite solubilisation rates enable direct addition To single cell protein bioreactors”. Muys M, Derese S, Verliefde A, Vlaeminck SE, , 10 p.
T2 (2016)
Keywords: P3 Proceeding; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
|
|
|
Keulemans M (2017) Study of electron transfer processes in plasmonic photocatalysis. 170 p
Keywords: Doctoral thesis; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
|
|
|
Asapu R (2018) A study of plasmonic systems using Layer-by-Layer synthesized core-shell nanoparticles. 142 p
Keywords: Doctoral thesis; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
|
|
|
“Success of mainstream partial nitritation/anammox demands integration of engineering, microbiome and modeling insights”. Agrawal S, Seuntjens D, De Cocker P, Lackner S, Vlaeminck SE, Current opinion in biotechnology 50, 214 (2018). http://doi.org/10.1016/J.COPBIO.2018.01.013
Abstract: Twenty years ago, mainstream partial nitritation/anammox (PN/A) was conceptually proposed as pivotal for a more sustainable treatment of municipal wastewater. Its economic potential spurred research, yet practice awaits a comprehensive recipe for microbial resource management. Implementing mainstream PN/A requires transferable and operable ways to steer microbial competition as to meet discharge requirements on a year-round basis at satisfactory conversion rates. In essence, the competition for nitrogen, organic carbon and oxygen is grouped into ON/OFF (suppression/promotion) and IN/OUT (wash-out/retention and seeding) strategies, selecting for desirable conversions and microbes. Some insights need mechanistic understanding, while empirical observations suffice elsewhere. The provided methodological R&D framework integrates insights in engineering, microbiome and modeling. Such synergism should catalyze the implementation of energy-positive sewage treatment.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1016/J.COPBIO.2018.01.013
|
|
|
“Sulfur-based denitrification treating regeneration water from ion exchange at high performance and low cost”. Vandekerckhove TGL, Kobayashi K, Janda J, Van Nevel S, Vlaeminck SE, Bioresource technology 257, 266 (2018). http://doi.org/10.1016/J.BIORTECH.2018.02.047
Abstract: Autotrophic denitrification with sulfur is an underexplored alternative to heterotrophic denitrification to remove nitrate from wastewater poor in organics. The application on ion exchange regeneration water (19.432.1 mS cm−1) is novel. Three fixed bed reactors were tested at 15 °C for >4 months, inoculated with activated sludge from sewage treatment. All were fast in start-up (<10 days) with high performance (94 ± 2% removal efficiency). pH control with NaOH rendered higher nitrate removal rates than limestone addition to the bed (211 ± 13 vs. 102 ± 13 mg N L−1 d−1), related to higher pH (6.64 vs. 6.24) and sulfur surface area. Bacterial communities were strongly enriched in Sulfurimonas (6367%) and Thiobacillus (2426%). In an economic comparison, sulfur-based denitrification (5.3 kg−1 N) was 15% cheaper than methanol-based denitrification (6.22 kg−1 N) and both treatments were opex dominated (85.9 vs. 86.5%). Overall, the technological and economic feasibility should boost further implementation of sulfurotrophic denitrification.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1016/J.BIORTECH.2018.02.047
|
|
|
“Sulphidotrophic denitrification treating regeneration water from ion exchange at high performance and low opex”. Vlaeminck SE, Kobayashi K, Jandra J, Van Nevel S, Vandekerckhove TGL, , 3 p.
T2 (2017)
Keywords: P3 Proceeding; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
|
|
|
“Supernatant organics from anaerobic digestion after thermal hydrolysis cause direct and/or diffusional activity loss for nitritation and anammox”. Zhang Q, Vlaeminck SE, DeBarbadillo C, Su C, Al-Omari A, Wett B, Pümpel T, Shaw A, Chandran K, Murthy S, De Clippeleir H, Water research 143, 270 (2018). http://doi.org/10.1016/J.WATRES.2018.06.037
Abstract: Treatment of sewage sludge with a thermal hydrolysis process (THP) followed by anaerobic digestion (AD) enables to boost biogas production and minimize residual sludge volumes. However, the reject water can cause inhibition to aerobic and anoxic ammonium-oxidizing bacteria (AerAOB & AnAOB), the two key microbial groups involved in the deammonification process. Firstly, a detailed investigation elucidated the impact of different organic fractions present in THP-AD return liquor on AerAOB and AnAOB activity. For AnAOB, soluble compounds linked to THP conditions and AD performance caused the main inhibition. Direct inhibition by dissolved organics was also observed for AerAOB, but could be overcome by treating the filtrate with extended aerobic or anaerobic incubation or with activated carbon. AerAOB additionally suffered from particulate and colloidal organics limiting the diffusion of substrates. This was resolved by improving the dewatering process through an optimized flocculant polymer dose and/or addition of coagulant polymer to better capture the large colloidal fraction, especially in case of unstable AD performance. Secondly, a new inhibition model for AerAOB included diffusion-limiting compounds based on the porter-equation, and achieved the best fit with the experimental data, highlighting that AerAOB were highly sensitive to large colloids. Overall, this paper for the first time provides separate identification of organic fractions within THP-AD filtrate causing differential types of inhibition. Moreover, it highlights the combined effect of the performance of THP, AD and dewatering on the downstream autotrophic nitrogen removal kinetics. (C) 2018 Elsevier Ltd. All rights reserved.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1016/J.WATRES.2018.06.037
|
|
|
“Sustainability appraisal tools for soil and groundwater remediation : how is the choice of remediation alternative influenced by different sets of sustainability indicators and tool structures?”.Beames A, Broekx S, Lookman R, Touchant K, Seuntjens P, The science of the total environment 470, 954 (2014). http://doi.org/10.1016/J.SCITOTENV.2013.10.044
Abstract: The state-of-the-science in sustainability assessment of soil and groundwater remediation is evaluated with the application of four decision support systems (DSSs) to a large-scale brownfield revitalization case study. The DSSs were used to perform sustainability appraisals of four technically feasible remediation alternatives proposed for the site. The first stage of the review compares the scope of each tool's sustainability indicators, how these indicators are measured and how the tools differ in terms of standardization and weighting procedures. The second stage of the review compares the outputs from the tools and determines the key factors that result in differing results between tools. The evaluation of indicator sets and tool structures explains why the tools generate differing results. Not all crucial impact areas, as identified by sustainable remediation forums, are thoroughly considered by the tools, particularly with regard to the social and economic aspects of sustainability. Variations in boundary conditions defined between technologies, produce distorted environmental impact results, especially when in-situ and ex-situ technologies are compared. The review draws attention to the need for end users to be aware of which aspects of sustainability are considered, how the aspects are measured and how all aspects are ultimately balanced in the evaluation of potential remediation strategies. Existing tools can be improved by considering different technologies within the same boundary conditions and by expanding indicator sets to include indicators deemed to be relevant by remediation forums. (C) 2013 Elsevier B.V. All rights reserved.
Keywords: A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1016/J.SCITOTENV.2013.10.044
|
|
|
“Sustainable industrial chemistry from a nontechnological viewpoint”. Reniers G, Sörensen K, Vrancken K page 33 (2013).
Keywords: H1 Book chapter; Economics; Engineering Management (ENM); Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1002/9783527649488.CH4
|
|
|
“Synergistic exposure of return-sludge to anaerobic starvation, sulfide and free ammonia to suppress nitrite oxidizing bacteria”. Seuntjens D, Van Tendeloo M, Chatzigiannidou I, Carvajal-Arroyo JM, Vandendriessche S, Vlaeminck SE, Boon N, Environmental science and technology 52, 8725 (2018). http://doi.org/10.1021/ACS.EST.7B06591
Abstract: A key step toward energy-positive sewage treatment is the development of mainstream partial nitritation/anammox, a nitrogen removal technology where aerobic ammonium-oxidizing bacteria (AerAOB) are desired, while nitrite-oxidizing bacteria (NOB) are not. To suppress NOB, a novel return-sludge treatment was investigated. Single and combined effects of sulfide (0-600 mg S L-1), anaerobic starvation (0-8 days), and a free ammonia (FA) shock (30 mg FA-N L-1 for 1 h) were tested for immediate effects and long-term recovery. AerAOB and NOB were inhibited immediately and proportionally by sulfide, with AerAOB better coping with the inhibition, while the short FA shock and anaerobic starvation had minor effects. Combinatory effects inhibited AerAOB and NOB more strongly. A combined treatment of sulfide (150 mg S L-1), 2 days of anaerobic starvation, and FA shock (30 mg FA-N L-1) inhibited AerAOB 14% more strongly compared to sulfide addition alone, while the AerAOB/NOB activity ratio remained constant. Despite no positive change being observed in the immediate-stress response, AerAOB recovered much faster than NOB, with a nitrite accumulation ratio (effluent nitrite on nitrite + nitrate) peak of 50% after 12 days. Studying long-term recovery is therefore crucial for design of an optimal NOB-suppression treatment, while applying combined stressors regularly may lead toward practical implementation.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1021/ACS.EST.7B06591
|
|
|
“Temperate bamboos in ornamental horticulture: differentiators and spillover effects into the 21st century”. Gielis J page 603 (2012).
Keywords: H3 Book chapter; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
|
|
|
“Temperature impact on sludge yield, settleability and kinetics of three heterotrophic conversions corroborates the prospect of thermophilic biological nitrogen removal”. Vandekerckhove TGL, De Mulder C, Boon N, Vlaeminck SE, Bioresource technology 269, 104 (2018). http://doi.org/10.1016/J.BIORTECH.2018.08.012
Abstract: In specific municipal and industrial cases, thermophilic wastewater treatment (>45 °C) might bring cost advantages over commonly applied mesophilic processes (1035 °C). To develop such a novel process, one needs sound parameters on kinetics, sludge yield and sludge settleability of three heterotrophic conversions: aerobic carbon removal, denitritation and denitrification. These features were evaluated in acetate-fed sequencing batch reactors (30, 40, 50 and 60 °C). Higher temperatures were accompanied by lower sludge production and maximum specific removal rates, resulting mainly from lower maximum growth rates. Thermophilic denitritation was demonstrated for the first time, with lower sludge production (1826%), higher nitrogen removal rates (2492%) and lower carbon requirement (40%) compared to denitrification. Acceptable settling of thermophilic aerobic (60 °C) and anoxic biomass (50 and 60 °C) was obtained. Overall, this parameter set may catalyze the establishment of thermophilic nitrogen removal, once nitritation and nitratation are characterized. Furthermore, waters with low COD/N ratio might benefit from thermophilic nitritation/denitritation.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1016/J.BIORTECH.2018.08.012
|
|
|
“13C incorporation as a tool to estimate biomass yields in thermophilic and mesophilic nitrifying communities”. Vandekerckhove TGL, Bodé, S, De Mulder C, Vlaeminck SE, Boon N, Frontiers in microbiology 10, 192 (2019). http://doi.org/10.3389/FMICB.2019.00192
Abstract: Current methods determining biomass yield require sophisticated sensors for in situ measurements or multiple steady-state reactor runs. Determining the yield of specific groups of organisms in mixed cultures in a fast and easy manner remains challenging. This study describes a fast method to estimate the maximum biomass yield (Ymax), based on 13C incorporation during activity measurements. It was applied to mixed cultures containing ammonia oxidizing bacteria (AOB) or archaea (AOA) and nitrite oxidizing bacteria (NOB), grown under mesophilic (1528∘C) and thermophilic (50∘C) conditions. Using this method, no distinction could be made between AOB and AOA co-existing in a community. A slight overestimation of the nitrifier biomass due to 13C redirection via SMP to heterotrophs could occur, meaning that this method determines the carbon fixation activity of the autotrophic microorganisms rather than the actual nitrifier biomass yield. Thermophilic AOA yields exceeded mesophilic AOB yields (0.22 vs. 0.060.11 g VSS g-1 N), possibly linked to a more efficient pathway for CO2 incorporation. NOB thermophilically produced less biomass (0.0250.028 vs. 0.0480.051 g VSS g-1 N), conceivably attributed to higher maintenance requirement, rendering less energy available for biomass synthesis. Interestingly, thermophilic nitrification yield was higher than its mesophilic counterpart, due to the dominance of AOA over AOB at higher temperatures. An instant temperature increase impacted the mesophilic AOB yield, corroborating the effect of maintenance requirement on production capacity. Model simulations of two realistic nitrification/denitrification plants were robust toward changing nitrifier yield in predicting effluent ammonium concentrations, whereas sludge composition was impacted. Summarized, a fast, precise and easily executable method was developed determining Ymax of ammonia and nitrite oxidizers in mixed communities.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.3389/FMICB.2019.00192
|
|