|
“Structural properties of Zn-substituted epitaxial YBa2Cu3O7-\delta thin films”. Ye M, Schroeder J, Mehbod M, Deltour R, Naessens G, Duvigneaud PH, Verbist K, Van Tendeloo G, Superconductor science and technology 9, 543 (1996). http://doi.org/10.1088/0953-2048/9/7/006
Abstract: We optimized the deposition of YBa2(Cu1-xZnx)(3)O-7-delta thin-films using inverted cylindrical magnetron sputtering and report here a detailed structural study, especially in relation to crystal growth, associated surface morphology, Y2O3 precipitation and other secondary phases important for flux pinning. We find that the epitaxial quality of the Zn-substituted YBa2Cu3O7-delta films is decreased compared with high-quality pure YBa2Cu3O7-delta films prepared under identical conditions. The pure films have smoother surfaces, while those of Zn-substituted films contain pinholes and outgrowths. Secondary phases and a-axis grains were observed in the Zn-substituted films. Y2O3 precipitates with typical dimensions of 50-100 Angstrom have been found in both pure and Zn-substituted samples. However, their density of about 10(23) m(-3), observed in the pure films, is significantly reduced in the Zn-substituted films when increasing the Zn concentration up to 4%.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 2.325
Times cited: 7
DOI: 10.1088/0953-2048/9/7/006
|
|
|
“First evidence of synthetic polygonal serpentines”. Devouard B, Baronnet A, Van Tendeloo G, Amelinckx S, European journal of mineralogy 9, 539 (1997)
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 1.362
Times cited: 15
|
|
|
“Measurement of the size of embedded metal clusters by mass spectrometry, transmission electron microscopy, and small-angle X-ray scattering”. Hendrich C, Favre L, Ievlev DN, Dobrynin AN, Bras W, Hörmann U, Piscopiello E, Van Tendeloo G, Lievens P, Temst K, Applied physics A : materials science &, processing 86, 533 (2007). http://doi.org/10.1007/s00339-006-3808-5
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 1.455
Times cited: 11
DOI: 10.1007/s00339-006-3808-5
|
|
|
“Ge40.0Te5.3I8: synthesis, crystal structure, and properties of a new clathrate-I compound”. Kovnir KA, Abramchuk NS, Zaikina JV, Baitinger M, Burkhardt U, Schnelle W, Olenev AV, Lebedev OI, Van Tendeloo G, Dikarev EV, Shevelkov AV, Zeitschrift für Kristallographie 221, 527 (2006). http://doi.org/10.1524/zkri.2006.221.5-7.527
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 3.179
Times cited: 16
DOI: 10.1524/zkri.2006.221.5-7.527
|
|
|
“Synthesis and characterization of mercury based “1222&rdquo, cuprates (Hg1-xMx)(Sr,Ba)2Pr2Cu2O9-\delta (M = Pr, Pb, Bi, Tl)”. Hervieu M, Van Tendeloo G, Michel C, Martin C, Maignan A, Raveau B, Journal of solid state chemistry 115, 525 (1995). http://doi.org/10.1006/jssc.1995.1169
Abstract: Five new layered cuprates, with a 1222-type structure, have been synthesized according to the formula (Hg(1-x)M(x))(Sr,Ba)(2) Pr2Cu2O9-delta with M = Pr, Pb, Pi, and Tl. They crystallize in a tetragonal cell with a approximate to a(p) and c approximate to 29.5 Angstrom; their structure consists in a triple intergrowth of oxygen-deficient perovskite, rock-salt-and fluorite-type layers. They are characterized by a mixed [Hg(1-x)M(x)O(1-delta)] layer in the rock-sail-type slice. The ED and HREM studies show that Tl, Bi, and Pb are statistically distributed in the mixed [Hg(1-x)M(x)O(1-delta)] layer, contrary to Pr which involves an ordering phenomenon along a. Different stacking defects are observed and discussed as well as the cleavage mode of the crystals. (C) 1995 Academic Press, Inc.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 2.133
Times cited: 5
DOI: 10.1006/jssc.1995.1169
|
|
|
“Atomic resolution electron tomography”. Bals S, Goris B, de Backer A, Van Aert S, Van Tendeloo G, MRS bulletin 41, 525 (2016). http://doi.org/10.1557/mrs.2016.138
Abstract: Over the last two decades, three-dimensional (3D) imaging by transmission electron microscopy or “electron tomography” has evolved into a powerful tool to investigate a variety of nanomaterials in different fields, such as life sciences, chemistry, solid-state physics, and materials science. Most of these results were obtained with nanometer-scale resolution, but different approaches have recently pushed the resolution to the atomic level. Such information is a prerequisite to understand the specific relationship between the atomic structure and the physicochemical properties of (nano) materials. We provide an overview of the latest progress in the field of atomic-resolution electron tomography. Different imaging and reconstruction approaches are presented, and state-of-the-art results are discussed. This article demonstrates the power and importance of electron tomography with atomic-scale resolution.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 5.199
Times cited: 19
DOI: 10.1557/mrs.2016.138
|
|
|
“Direct observation of ferrielectricity at ferroelastic domain boundaries in CaTiO3 by electron microscopy”. Van Aert S, Turner S, Delville R, Schryvers D, Van Tendeloo G, Salje EKH, Advanced materials 24, 523 (2012). http://doi.org/10.1002/adma.201103717
Abstract: High-resolution aberration-corrected transmission electron microscopy aided by statistical parameter estimation theory is used to quantify localized displacements at a (110) twin boundary in orthorhombic CaTiO3. The displacements are 36 pm for the Ti atoms and confined to a thin layer. This is the first direct observation of the generation of ferroelectricity by interfaces inside this material which opens the door for domain boundary engineering.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 19.791
Times cited: 150
DOI: 10.1002/adma.201103717
|
|
|
“Electron-microscopy and the structural studies of superconducting materials and fullerites”. Van Tendeloo G, Amelinckx S, NATO Advanced Study Institutes series: series E : applied sciences
T2 –, NATO Advanced Study Institute on Materials and crystallographic Aspects, of HT(c)-Superconductivity, May 17-30, 1993, Erice, Italy , 521 (1994)
Keywords: P1 Proceeding; Electron microscopy for materials research (EMAT)
|
|
|
“New cation deficient perovskite-like oxides in the system La4Ti3O12-LaTiO3”. Bontchev R, Darriet B, Darriet J, Weill F, Van Tendeloo G, Amelinckx S, European journal of solid state and inorganic chemistry 30, 521 (1993)
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Times cited: 19
|
|
|
“Growth mechanism of epitaxial SrTiO3 on a (1 x 2) + (2 x 1) reconstructed Sr(1/2 ML)/Si(001) surface”. Spreitzer M, Klement D, Egoavil R, Verbeeck J, Kovac J, Zaloznik A, Koster G, Van Tendeloo G, Suvorov D, Rijnders G, Journal Of Materials Chemistry C 8, 518 (2020). http://doi.org/10.1039/C9TC04092G
Abstract: Sub-monolayer control over the growth at silicon-oxide interfaces is a prerequisite for epitaxial integration of complex oxides with the Si platform, enriching it with a variety of functionalities. However, the control over this integration is hindered by the intense reaction of the constituents. The most suitable buffer material for Si passivation is metallic strontium. When it is overgrown with a layer of SrTiO3 (STO) it can serve as a pseudo-substrate for the integration with functional oxides. In our study we determined a mechanism for epitaxial integration of STO with a (1 x 2) + (2 x 1) reconstructed Sr(1/2 ML)/Si(001) surface using all-pulsed laser deposition (PLD) technology. A detailed analysis of the initial deposition parameters was performed, which enabled us to develop a complete protocol for integration, taking into account the peculiarities of the PLD growth, STO critical thickness, and process thermal budget, in order to kinetically trap the reaction between STO and Si and thus to minimize the thickness of the interface layer. The as-prepared oxide layer exhibits STO(001)8Si(001) out-of-plane and STO[110]8Si[100] in-plane orientation and together with recent advances in large-scale PLD tools these results represent a new technological solution for the implementation of oxide electronics on demand.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 6.4
Times cited: 12
DOI: 10.1039/C9TC04092G
|
|
|
“HREM investigation of La(1-x)Ca(x)MnO3-delta thin films”. Lebedev O, Van Tendeloo G, Amelinckx S, Leibold B, Habermeier HU, , 517 (1998)
Keywords: P1 Proceeding; Electron microscopy for materials research (EMAT)
|
|
|
“HREM investigation of La1-xCaxMnO3- thin films”. Lebedev OI, Van Tendeloo G, Amelinckx S, Leibold B, Habermeier H-U, Electron microscopy: vol. 2 , 517 (1998)
Keywords: A3 Journal article; Electron microscopy for materials research (EMAT)
|
|
|
“Combined TiO2/SiO2 mesoporous photocatalysts with location and phase controllable TiO2 nanoparticles”. Beyers E, Biermans E, Ribbens S, de Witte K, Mertens M, Meynen V, Bals S, Van Tendeloo G, Vansant EF, Cool P, Applied catalysis : B : environmental 88, 515 (2009). http://doi.org/10.1016/j.apcatb.2008.10.009
Abstract: Combined TiO2/SiO2 mesoporous materials were prepared by deposition of TiO2 nanoparticles synthesised via the acid-catalysed solgel method. In the first synthesis step a titania solution is prepared, by dissolving titaniumtetraisopropoxide in nitric acid. The influences of the initial titaniumtetraisopropoxide concentration and the temperature of dissolving on the final structural properties were investigated. In the second step of the synthesis, the titania nanoparticles were deposited on a silica support. Here, the influence of the temperature during deposition was studied. The depositions were carried out on two different mesoporous silica supports, SBA-15 and MCF, leading to substantial differences in the catalytic and structural properties. The samples were analysed with N2-sorption, X-ray diffraction (XRD), electron probe microanalysis (EPMA) and transmission electron microscopy (TEM) to obtain structural information, determining the amount of titania, the crystal phase and the location of the titania particles on the mesoporous material (inside or outside the mesoporous channels). The structural differences of the support strongly determine the location of the nanoparticles and the subsequent photocatalytic activity towards the degradation of rhodamine 6G in aqueous solution under UV irradiation.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT); Laboratory of adsorption and catalysis (LADCA)
Impact Factor: 9.446
Times cited: 69
DOI: 10.1016/j.apcatb.2008.10.009
|
|
|
“The morphology, structure and texture of carbon nanotubes: an electron microscopy study”. Amelinckx S, Bernaerts D, Van Tendeloo G, van Landuyt J, Lucas AA, Mathot M, Lambin P, , 515 (1995)
Keywords: P3 Proceeding; Electron microscopy for materials research (EMAT)
|
|
|
“Expanded graphite as a support for Ni/carbon composites”. Afanasov IM, Shornikova ON, Avdeev VV, Lebedev OI, Van Tendeloo G, Matveev AT, Carbon 47, 513 (2009). http://doi.org/10.1016/j.carbon.2008.10.034
Abstract: Expanded graphite decorated with nickel oxide particles (EGNiO) has been synthesized through electrochemical oxidation of natural graphite in an aqueous nickel nitrate solution followed by a heat treatment. EGNiO was used to prepare nickel/carbon composites using two techniques: (a) hydrogen reduction of nickel oxide particles loaded on the expanded graphite surface and (b) pyrolysis of coal tar pitch-impregnated EGNiO blocks. The EGNiO as well as the nickel/carbon composites have been characterized by X-ray diffraction, scanning and transmission electron microscopy, energy dispersive X-ray spectroscopy and selected area electron diffraction.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 6.337
Times cited: 45
DOI: 10.1016/j.carbon.2008.10.034
|
|
|
“On the relationship between morphology, composition and structure of Al-Cu-Fe crystals and quasicrystals”. Balzuweit K, Meekes H, Van Tendeloo G, de Boer JL, Philosophical magazine: B: physics of condensed matter: electronic, optical and magnetic properties 67, 513 (1993). http://doi.org/10.1080/13642819308207689
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Times cited: 10
DOI: 10.1080/13642819308207689
|
|
|
“Addition of yttrium into HfO2 films: microstructure and electrical properties”. Dubourdieu C, Rauwel E, Roussel H, Ducroquet F, Hollaender B, Rossell M, Van Tendeloo G, Lhostis S, Rushworth S, Journal of vacuum science and technology: A: vacuum surfaces and films 27, 503 (2009). http://doi.org/10.1116/1.3106627
Abstract: The cubic phase of HfO2 was stabilized by addition of yttrium in thin films grown on Si/SiO2 by metal-organic chemical vapor deposition. The cubic phase was obtained for contents of 6.5 at. % Y or higher at a temperature as low as 470 °C. The complete compositional range (from 1.5 to 99.5 at. % Y) was investigated. The crystalline structure of HfO2 was determined from x-ray diffraction, electron diffraction, and attenuated total-reflection infrared spectroscopy. For cubic films, the continuous increase in the lattice parameter indicates the formation of a solid-solution HfO2Y2O3. As shown by x-ray photoelectron spectroscopy, yttrium silicate is formed at the interface with silicon; the interfacial layer thickness increases with increasing yttrium content and increasing film thickness. The dependence of the intrinsic relative permittivity r as a function of Y content was determined. It exhibits a maximum of ~30 for ~8.8 at. % Y. The cubic phase is stable upon postdeposition high-temperature annealing at 900 °C under NH3.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 1.374
Times cited: 29
DOI: 10.1116/1.3106627
|
|
|
“Effect of growth interrupt and growth rate on MOVPE-grown InGaN/GaN MQW structures”. Jacobs K, van Daele B, Leys M, Moerman I, Van Tendeloo G, Journal of crystal growth 248, 498 (2003). http://doi.org/10.1016/S0022-0248(02)01847-X
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 1.751
Times cited: 14
DOI: 10.1016/S0022-0248(02)01847-X
|
|
|
“Electron microscopy of fullerenes and fullerene related structures”. Van Tendeloo G, van Landuyt J, Amelinckx S, , 498 (1994)
Keywords: P3 Proceeding; Electron microscopy for materials research (EMAT)
|
|
|
“Microstructure of CuXMo6S8 Chevrel phase thin films on R-plane sapphire”. Richard O, Van Tendeloo G, Lemée N, le Lannic J, Guilloux-Viry M, Perrin A, Journal of electron microscopy 49, 493 (2000). http://doi.org/10.1093/oxfordjournals.jmicro.a023834
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 0.9
DOI: 10.1093/oxfordjournals.jmicro.a023834
|
|
|
“Structural transformation in fluorinated LaACuGaO5 (A=Ca, Sr) brownmillerites”. Hadermann J, Van Tendeloo G, Abakumov AM, Pavlyuk BP, Rozova MG, Antipov EV, International journal of inorganic materials 2, 493 (2000). http://doi.org/10.1016/S1466-6049(00)00072-6
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Times cited: 13
DOI: 10.1016/S1466-6049(00)00072-6
|
|
|
“Synthesis and characterization of new phases: Sr3.75K1.75Bi3O12 and Sr3.1Na2.9Bi3O12”. Pshirkov JS, Kazakov SM, Abakumov AM, Putilin SN, Antipov EV, Bougerol-Chaillout C, Lebedev OI, Van Tendeloo G, Journal of solid state chemistry 152, 492 (2000). http://doi.org/10.1006/jssc.2000.8718
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 2.299
Times cited: 2
DOI: 10.1006/jssc.2000.8718
|
|
|
“Synthesis and structural study of hexagonal pervoskites in the Ba5>Ta4O15-MZrO3 (M=Ba, Sr) system”. Abakumov AM, Shpanchenko RV, Antipov EV, Lebedev OI, Van Tendeloo G, Amelinckx S, Journal of solid state chemistry 141, 492 (1998). http://doi.org/10.1006/jssc.1998.8001
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 2.299
Times cited: 17
DOI: 10.1006/jssc.1998.8001
|
|
|
“Structure and microstructure of nanoscale mesoporous silica spheres”. Lebedev OI, Van Tendeloo G, Collart O, Cool P, Vansant EF, Solid state sciences 6, 489 (2004). http://doi.org/10.1016/j.solidstatesciences.2004.01.013
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT); Laboratory of adsorption and catalysis (LADCA)
Impact Factor: 1.811
Times cited: 42
DOI: 10.1016/j.solidstatesciences.2004.01.013
|
|
|
“Reduced dimensionality in different forms of carbon”. Van Tendeloo G, Bernaerts D, Amelinckx S, Fullerenes and carbon based materials , 487 (1998)
Abstract: Several TEM techniques are used to characterise the local structure of low dimensional forms of carbon. HREM is particularly useful to describe the defect structure of thin films of diamond or fullerenes and C-60-C-70 nanoclusters. A columnar form of graphite is analysed, mainly by electron diffraction which allowed us to propose a growth mechanism. Diffraction contrast dark field microscopy, in combination with electron diffraction, allows a detailed characterisation of carbon nanotubes; e.g. the chirality distribution of tubes in ropes of single wall tubes is studied by selected area electron diffraction. (C) 1998 Elsevier Science Ltd. All rights reserved.
Keywords: P1 Proceeding; Electron microscopy for materials research (EMAT)
|
|
|
“Reduced dimensionality in different forms of carbon”. Van Tendeloo G, Bernaerts D, Amelinckx S, Carbon 36, 487 (1998). http://doi.org/10.1016/S0008-6223(98)00050-5
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 6.337
Times cited: 4
DOI: 10.1016/S0008-6223(98)00050-5
|
|
|
“Stabilization of mercury-based superconductors by foreign cations”. Raveau B, Michel C, Hervieu M, Van Tendeloo G, Maignan A, Annales de chimie (1914)
T2 –, 4th North-African Materials Science Symposium (JMSM 94), NOV 23-24, 1994, CASABLANCA, MOROCCO 19, 487 (1994)
Abstract: The recently discovered superconducting mercury-based cuprates HgBa2Can-1CunO2n+2+delta have proved difficult to synthesize as single phases and are sensitive to environment (CO2, moisture). The present paper gives an overview of new series mercury based superconductors, whose stabilisation is based on the fact that a foreign cation with a higher valency than Hg(II) must be introduced in the mercury layers, in order to fill up partially the oxygen vacancies of these layers. By this method, several new series of superconductors involving strontium instead of barium with critical temperatures ranging from 27 K to 95 K have been isolated : Hg0.5Bi0.5Sr2-xLaxCuO4+delta, Hg(0.5)Bi(0.5)Sr(2)Ca(1-x)R(x)Cu(2)O(6+delta) (R Y, Nd, Pr), Pb0.7Hg0.3Sr2-xLaxCuO4+delta, Pb(0.7)Hg(0.3)Sr(2)Ca(1-x)R(x)Cu(2)O(6+delta) (R = Y, Nd) Hg(1-x)Pr(x)Sr(2)A(1-x')Pr(x') Cu2O6+delta (A = Sr, Ca), Pb0.7Hg0.3Sr2Cu2CO3O7 and Hg1-xCrxSr2CuO4+delta. The behaviour of the praseodymium cuprates that exhibit a rather sharp transition and reach a Tc of 85 K is especially discussed. A method to synthesize new ''Ba-Hg'' superconducting cuprates with the 1212 structure at normal pressure with a Tc up to 110 K is also presented.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Times cited: 2
|
|
|
“Experimental validation of edge strength model for glass with polished and cut edge finishing”. Vandebroek M, Belis J, Louter C, Van Tendeloo G, Engineering fracture mechanics 96, 480 (2012). http://doi.org/10.1016/j.engfracmech.2012.08.019
Abstract: In literature, the experimental validation of a glass edge strength model is lacking. Therefore, in this study, an edge strength model was established and validated. The short-term parameters of the edge strength model, i.e. the flaw geometry and depth, were determined by means of testing at a high stress rate. This was done for polished and cut edges. Next, the strength model, including subcritical crack growth, was established. Finally, the edge strength model was validated by the test results at a low stress rate. The assessed model was found to be slightly conservative, compared to the test results.
Keywords: A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
Impact Factor: 2.151
Times cited: 15
DOI: 10.1016/j.engfracmech.2012.08.019
|
|
|
“Three-Dimensional Quantification of the Facet Evolution of Pt Nanoparticles in a Variable Gaseous Environment”. Altantzis T, Lobato I, De Backer A, Béché, A, Zhang Y, Basak S, Porcu M, Xu Q, Sánchez-Iglesias A, Liz-Marzán LM, Van Tendeloo G, Van Aert S, Bals S, Nano letters 19, 477 (2019). http://doi.org/10.1021/acs.nanolett.8b04303
Abstract: Pt nanoparticles play an essential role in a wide variety of catalytic reactions. The activity of the particles strongly depends on their three-dimensional (3D) structure and exposed facets, as well as on the reactive environment. High-resolution electron microscopy has often been used to characterize nanoparticle catalysts but unfortunately most observations so far have been either performed in vacuum and/or using conventional (2D) in situ microscopy. The latter however does not provide direct 3D morphological information. We have implemented a quantitative methodology to measure variations of the 3D atomic structure of nanoparticles under the flow of a selected gas. We were thereby able to quantify refaceting of Pt nanoparticles with atomic resolution during various oxidation−reduction cycles. In a H2 environment, a more faceted surface morphology of the particles was observed with {100} and {111} planes being dominant. On the other hand, in O2 the percentage of {100} and {111} facets decreased and a significant increase of higher order facets was found, resulting in a more rounded morphology. This methodology opens up new opportunities toward in situ characterization of catalytic nanoparticles because for the first time it enables one to directly measure 3D morphology variations at the atomic scale in a specific gaseous reaction environment.
Keywords: A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
Impact Factor: 12.712
Times cited: 82
DOI: 10.1021/acs.nanolett.8b04303
|
|
|
“Structure and phase transitions in C60 and C70 fullerites”. Van Tendeloo G, Muto S, van Heurck C, Amelinckx S, , 476 (1992)
Keywords: P3 Proceeding; Electron microscopy for materials research (EMAT)
Times cited: 1
|
|