“Cytokinin dynamics in cell suspension cultures of Bambusa balcooa Roxburgh using UPLC-ESI/MS/MS”. Van den Akker S, Bormans P, Peeters H, Gielis J, Prinsen E page 539 (2012).
Keywords: H3 Book chapter; Engineering sciences. Technology; Integrated Molecular Plant Physiology Research (IMPRES); Sustainable Energy, Air and Water Technology (DuEL)
|
“New method for selective Cr recovery from stainless steel slag by NaOCl assisted alkaline leaching and consecutive BaCrO4 precipitation”. Kim E, Spooren J, Broos K, Nielsen P, Horckmans L, Vrancken KC, Quaghebeur M, Chemical engineering journal 295, 542 (2016). http://doi.org/10.1016/J.CEJ.2016.03.073
Abstract: A new hydrometallurgical method was investigated for selective leaching of chromium from stainless steel slag (SS slag) consisting of temperature controlled extraction with NaOH in the presence of NaOCl, followed by water leaching. After parameter optimization of the NaOCl-NaOH extraction step, a selective Cr leaching of 68% was reached, while dissolution of matrix materials was low (Al 0.3%, Ca 2.0%, Si 0.4%). The optimum conditions for the investigated system are: 105 degrees C, 6 h, SS slag particle size <63 mu m, mass ratio of NaOH to SS slag 0.13, and 3.3 mmol NaOCl to 1 g SS slag. The described oxidative alkaline leaching process by hypochlorite enables selective recovery of Cr at a significantly lower temperature and required amount of alkaline agent than molten salt or alkaline roasting processes. BaCrO4 was precipitated to purify and concentrate Cr from the leachate in which also minor amounts of Mn and V were present. This method allowed for a 99.9% Cr recovery rate. The obtained leaching residue shows no alterations of the SS slag's mineralogy with respect to untreated material. Therefore, a known carbonation treatment of the slag can be applied to prepare novel construction materials with a lowered Cr content. (C) 2016 Elsevier B.V. All rights reserved.
Keywords: A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1016/J.CEJ.2016.03.073
|
“Measuring adaptive capacity of urban wastewater infrastructure : change impact and change propagation”. Spiller M, The science of the total environment 601-602, 571 (2017). http://doi.org/10.1016/J.SCITOTENV.2017.05.161
Abstract: The ability of urban wastewater systems to adapt and transform as a response to change is an integral part of sustainable development. This requires technology and infrastructure that can be adapted to new operational challenges. In this study the adaptive capacity of urban wastewater systems is evaluated by assessing the interdependencies between system components. In interdependent and therefore tightly coupled systems, changes to one systems component will require alteration elsewhere in the system, therefore impairing the capacity of these systems to be changed. The aim of this paper is to develop a methodology to evaluate the adaptive capacity of urban wastewater systems by assessing how change drivers and innovation affect existing wastewater technology and infrastructure. The methodology comprises 7 steps and applies a change impact table and a design structure matrix that are completed by experts during workshops. Change impact tables quantify where change drivers, such as energy neutrality and resource recovery, require innovation in a system. The design structure matrix is a tool to quantify emerging changes that are a result of the innovation. The method is applied for the change driver of energy neutrality and shown for two innovations: a decentralised upflow anaerobic sludge blanket reactor followed by an anammox process and a conventional activated sludge treatment with enhanced chemical precipitation and high temperature-high pressure hydrolysis. The results show that the energy neutrality of wastewater systems can be address by either innovation in the decentralised or centralised treatment. The quantification of the emerging changes for both innovations indicates that the decentralised treatment is more disruptive, or in other words, the system needs to undergo more adaptation. It is concluded that the change impact and change propagation method can be used to characterise and quantify the technological or infrastructural transformations. In addition, it provides insight into the stakeholders affected by change.
Keywords: A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1016/J.SCITOTENV.2017.05.161
|
“Characterization and optimization of \beta-galactosidase immobilization process on a mixed-matrix membrane”. Jochems P, Satyawali Y, van Roy S, Doyen W, Diels L, Dejonghe W, Enzyme and microbial technology 49, 580 (2011). http://doi.org/10.1016/J.ENZMICTEC.2011.06.010
Abstract: β-Galactosidase is an important enzyme catalyzing not only the hydrolysis of lactose to the monosaccharides glucose and galactose but also the transgalactosylation reaction to produce galacto-oligosaccharides (GOS). In this study, β-galactosidase was immobilized by adsorption on a mixed-matrix membrane containing zirconium dioxide. The maximum β-galactosidase adsorbed on these membranes was 1.6 g/m2, however, maximal activity was achieved at an enzyme concentration of around 0.5 g/m2. The tests conducted to investigate the optimal immobilization parameters suggested that higher immobilization can be achieved under extreme parameters (pH and temperature) but the activity was not retained at such extreme operational parameters. The investigations on immobilized enzymes indicated that no real shift occurred in its optimal temperature after immobilization though the activity in case of immobilized enzyme was better retained at lower temperature (5 °C). A shift of 0.5 unit was observed in optimal pH after immobilization (pH 6.5 to 7). Perhaps the most striking results are the kinetic parameters of the immobilized enzyme; while the Michaelis constant (Km) value increased almost eight times compared to the free enzyme, the maximum enzyme velocity (Vmax) remained almost constant.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1016/J.ENZMICTEC.2011.06.010
|
“Benchmark study on algae harvesting with backwashable submerged flat panel membranes”. de Baerdemaeker T, Lemmens B, Dotremont C, Fret J, Roef L, Goiris K, Diels L, Bioresource technology 129, 582 (2013). http://doi.org/10.1016/J.BIORTECH.2012.10.153
Abstract: The feasibility of algae harvesting with submerged flat panel membranes was investigated as pre-concentration step prior to centrifugation. Polishing of the supernatant coming from the centrifuge was evaluated as well. The effect of membrane polymer (polyvinyl chloride [PVC], polyethersulfone polyvinyl-pyrollidone [PES-PVP], poly vinylidene fluoride [PVDF]), pore size (microfiltration [MF], ultrafiltration [UF]), algae cell concentrations and species were investigated at lab-scale. In addition, backwashing as fouling control was compared to standard relaxation. PVDF was the superior polymer, and UF showed better fouling resistance. Backwashing outperformed relaxation in fouling control. The backwashable membranes allowed up to 300% higher fluxes compared to commercial flat panel benchmark (PVC) membranes. Estimations on energy consumption for membrane filtration followed by centrifugation revealed relatively low values of 0.169 kW h/kg of dry weight of algae compared to 0.5 kW h/kg for algae harvesting via classical centrifuge alone. (C) 2012 Elsevier Ltd. All rights reserved.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1016/J.BIORTECH.2012.10.153
|
“Resource recovery from pig manure via an integrated approach : a technical and economic assessment for full-scale applications”. De Vrieze J, Colica G, Pintucci C, Sarli J, Pedizzi C, Willeghems G, Bral A, Varga S, Prat D, Peng L, Spiller M, Buysse J, Colsen J, Benito O, Carballa M, Vlaeminck SE, Bioresource technology 272, 582 (2019). http://doi.org/10.1016/J.BIORTECH.2018.10.024
Abstract: Intensive livestock farming cannot be uncoupled from the massive production of manure, requiring adequate management to avoid environmental damage. The high carbon, nitrogen and phosphorus content of pig manure enables targeted resource recovery. Here, fifteen integrated scenarios for recovery of water, nutrients and energy are compared in terms of technical feasibility and economic viability. The recovery of refined nutrients with a higher market value and quality, i.e., (NH4)2SO4 for N and struvite for P, coincided with higher net costs, compared to basic composting. The inclusion of anaerobic digestion promoted nutrient recovery efficiency, and enabled energy recovery through electricity production. Co-digestion of the manure with carbon-rich waste streams increased electricity production, but did not result in lower process costs. Overall, key drivers for the selection of the optimal manure treatment scenario will include the market demand for more refined (vs. separated or concentrated) products, and the need for renewable electricity production.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1016/J.BIORTECH.2018.10.024
|
“A spatial approach to identify priority areas for pesticide pollution mitigation”. Quaglia G, Joris I, Broekx S, Desmet N, Koopmans K, Vandaele K, Seuntjens P, Journal of environmental management 246, 583 (2019). http://doi.org/10.1016/J.JENVMAN.2019.04.120
Abstract: Identifying priority areas is an essential step in developing management strategies to reduce pesticide loads in surface water. A spatially explicit model-based approach was developed to detect priority areas for diffuse pesticide pollution at catchment scale. The method uses available datasets and considers different pesticide pathways in the environment post-application. The approach was applied in a catchment area in SE Flanders (Belgium) as a case study. Calculated risk areas were obtained using detailed landscape data and combining pesticide emissions and hydrological connectivity. The risk areas obtained were further compared with an alternative observation-based method, developed specifically for this study site that includes long-term field observations and local expert knowledge. Both methods equally classified 50% of the areas. The impact of crop rotation on the calculated risk was analysed. High-risk areas were identified and added to a cumulative map over all five years to evaluate temporal variations. The model-based approach was used for the initial identification of risk areas at the study site. The tool helps to prioritise zones and detect particular fields to target landscape mitigation measures to reduce diffuse pesticide pollution reaching surface water bodies.
Keywords: A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1016/J.JENVMAN.2019.04.120
|
“Why does not the leaf weight-area allometry of bamboos follow the 3/2-power law?”.Lin S, Shao L, Hui C, Song Y, Reddy GVP, Gielis J, Li F, Ding Y, Wei Q, Shi P, Reddy GVP, Frontiers in plant science 9, 583 (2018). http://doi.org/10.3389/FPLS.2018.00583
Abstract: The principle of similarity (Thompson, 1917) states that the weight of an organism follows the 3/2-power law of its surface area and is proportional to its volume on the condition that the density is constant. However, the allometric relationship between leaf weight and leaf area has been reported to greatly deviate from the 3/2-power law, with the irregularity of leaf density largely ignored for explaining this deviation. Here, we choose 11 bamboo species to explore the allometric relationships among leaf area (A), density (ρ), length (L), thickness (T), and weight (W). Because the edge of a bamboo leaf follows a simplified two-parameter Gielis equation, we could show that A ∝ L2 and that A ∝ T2. This then allowed us to derive the density-thickness allometry ρ ∝ Tb and the weight-area allometry W ∝ A(b+3)/2 ≈ A9/8, where b approximates −3/4. Leaf density is strikingly negatively associated with leaf thickness, and it is this inverse relationship that results in the weight-area allometry to deviate from the 3/2-power law. In conclusion, although plants are prone to invest less dry mass and thus produce thinner leaves when the leaf area is sufficient for photosynthesis, such leaf thinning needs to be accompanied with elevated density to ensure structural stability. The findings provide the insights on the evolutionary clue about the biomass investment and output of photosynthetic organs of plants. Because of the importance of leaves, plants could have enhanced the ratio of dry material per unit area of leaf in order to increase the efficiency of photosynthesis, relative the other parts of plants. Although the conclusion is drawn only based on 11 bamboo species, it should also be applicable to the other plants, especially considering previous works on the exponent of the weight-area relationship being less than 3/2 in plants.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.3389/FPLS.2018.00583
|
“Process development for hydrometallurgical recovery of valuable metals from sulfide-rich residue generated in a secondary lead smelter”. Kim E, Roosen J, Horckmans L, Spooren J, Broos K, Binnemans K, Vrancken KCM, Quaghebeur M, Hydrometallurgy 169, 589 (2017). http://doi.org/10.1016/J.HYDROMET.2017.04.002
Abstract: Two routes were investigated to selectively recover lead and minor metals (Cu, Ni, Zn) from a sulfide-rich lead smelter residue, matte. The first route comprises a two-step leaching process that combines Fe(III)-HNO3 leaching with roasting, followed by water leaching. In the first step, the efficiency of Pb leaching was 90% at the optimum condition (L/S ratio 8, 0.5 mol.L-1 HNO3, 0.15 mol.L-1 Fe(III), 25 degrees C). In the second step, roasting at 600 degrees C followed by water leaching at 50 degrees C selectively leached Ni, Cu, and Zn while fully converting iron sulfides to oxides. One-step oxidative pressure leaching in HNO3 was investigated as an alternative to simultaneously leach Pb, Cu, Ni and Zn. At the optimal conditions (130 degrees C, 60 min, 0.3 mol.L-1 HNO3, 0.07 mol.L-1 Fe(III), L/S ratio 20), Pb, Cu, Zn and Ni leaching were 92, 60, 70 and 66%, respectively, while Fe leaching remained low (2%). The leachates obtained from both leaching routes were treated by ion-exchange adsorption with diethylenetriaminepentaacetic acid (DTPA) functionalized chitosan-silica hybrid materials to investigate the selective recovery of Cu, Zn and Ni. The adsorption order appeared to be in the same order as the corresponding stability constants for complexes between the respective metal ions and free DTPA: Ca(II) < Zn(II) < Pb (II) approximate to Ni(II) < Cu(II). This allows not only to selectively recover Cu, Zn and Ni from the leachates, but also to mutually separate them by using the functionalized resin as a stationary phase in column chromatography. To avoid adsorbent contamination, Fe(III) and Pb(II) may be removed from the leachates in a pre-treatment step. Based on these results, the investigated methods can be combined as process steps of two possible routes for the selective recovery of valuable metals from the studied secondary lead smelting residue. The two-step leaching process seems to be superior since a more concentrated solution of Cu, Ni, and Zn is produced in the 2nd leaching step with low capital cost.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1016/J.HYDROMET.2017.04.002
|
“Enhanced biomethanation of kitchen waste by different pre-treatments”. Ma J, Duong TH, Smits M, Verstraete W, Carballa M, Bioresource technology 102, 592 (2011). http://doi.org/10.1016/J.BIORTECH.2010.07.122
Abstract: Five different pre-treatments were investigated to enhance the solubilisation and anaerobic biodegradability of kitchen waste (
KW) in thermophilic batch and continuous tests. In the batch solubilisation tests, the highest and the lowest solubilisation efficiency were achieved with the thermo-acid and the pressuredepressure pre-treatments, respectively. However, in the batch biodegradability tests, the highest cumulative biogas production was obtained with the pressuredepressure method. In the continuous tests, the best performance in terms of an acceptable biogas production efficiency of 60% and stable in-reactor CODs and VFA concentrations corresponded to the pressuredepressure reactor, followed by freezethaw, acid, thermo-acid, thermo and control. The maximum OLR (5 g COD L−1 d−1) applied in the pressuredepressure and freezethaw reactors almost doubled the control reactor. From the overall analysis, the freezethaw pre-treatment was the most profitable process with a net potential profit of around 11.5 ton−1 KW.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1016/J.BIORTECH.2010.07.122
|
“Laboratory-scale membrane up-concentration and co-anaerobic digestion for energy recovery from sewage and kitchen waste”. Nguyen Thi Tuyet, Nguyen Phuoc Dan, Nguyen Cong Vu, Nguyen Le Hoang Trung, Bui Xuan Thanh, De Wever H, Goemans M, Diels L, Water science and technology 73, 597 (2016). http://doi.org/10.2166/WST.2015.535
Abstract: This study assessed an alternative concept for co-treatment of sewage and organic kitchen waste in Vietnam. The goal was to apply direct membrane filtration for sewage treatment to generate a permeate that is suitable for discharge. The obtained chemical oxygen demand (COD) concentrations in the permeate of ultrafiltration tests were indeed under the limit value (50 mg/L) of the local municipal discharge standards. The COD of the concentrate was 5.4 times higher than that of the initial feed. These concentrated organics were then co-digested with organic kitchen wastes at an organic loading rate of 2.0 kg VS/m(3).d. The volumetric biogas production of the digester was 1.94 +/- 0.34 m(3)/m(3).d. The recovered carbon, in terms of methane gas, accounted for 50% of the total carbon input of the integrated system. Consequently, an electrical production of 64 Wh/capita/d can be obtained when applying the proposed technology with the current wastes generated in Ho Chi Minh City. Thus, it is an approach with great potential in terms of energy recovery and waste treatment.
Keywords: A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.2166/WST.2015.535
|
“Temperate bamboos in ornamental horticulture: differentiators and spillover effects into the 21st century”. Gielis J page 603 (2012).
Keywords: H3 Book chapter; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
|
“Elucidating the photocatalytic degradation pathway of acetaldehyde : an FTIR in situ study under atmospheric conditions”. Hauchecorne B, Terrens D, Verbruggen S, Martens JA, van Langenhove H, Demeestere K, Lenaerts S, Applied catalysis : B : environmental 106, 630 (2011). http://doi.org/10.1016/J.APCATB.2011.06.026
Abstract: In this paper, new insights of the photocatalytic oxidation pathway of acetaldehyde are obtained by means of an in-house constructed FTIR in situ reactor. It is shown that there are generally three different intermediates present: acetic acid, formic acid and formaldehyde. By means of FTIR in situ spectroscopy, this study revealed that these intermediates are bound on the TiO2 surface in different ways, resulting in the presence of more intermediate species, such as molecularly adsorbed acetic acid, bidentate acetate, molecularly adsorbed formic acid, monodentate formate, bidentate formate, formaldehyde and dioxymethylene. Furthermore, spectroscopic evidence is obtained concerning the formation of 3-hydroxybutanal and crotonaldehyde upon adsorption of acetaldehyde on TiO2 prior to UV illumination. The presented results thus give new insights in the photocatalytic oxidation pathway of acetaldehyde.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 9.446
Times cited: 46
DOI: 10.1016/J.APCATB.2011.06.026
|
“The generalized Gielis geometric equation and its application”. Shi P, Ratkowsky DA, Gielis J, Symmetry-Basel 12, 645 (2020). http://doi.org/10.3390/SYM12040645
Abstract: Many natural shapes exhibit surprising symmetry and can be described by the Gielis equation, which has several classical geometric equations (for example, the circle, ellipse and superellipse) as special cases. However, the original Gielis equation cannot reflect some diverse shapes due to limitations of its power-law hypothesis. In the present study, we propose a generalized version by introducing a link function. Thus, the original Gielis equation can be deemed to be a special case of the generalized Gielis equation (GGE) with a power-law link function. The link function can be based on the morphological features of different objects so that the GGE is more flexible in fitting the data of the shape than its original version. The GGE is shown to be valid in depicting the shapes of some starfish and plant leaves.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 2.7
Times cited: 4
DOI: 10.3390/SYM12040645
|
“Effective carbon and nutrient treatment solutions for mixed domestic-industrial wastewater in India”. Saha S, Badhe N, Seuntjens D, Vlaeminck SE, Biswas R, Nandy T, Water science and technology 72, 651 (2015). http://doi.org/10.2166/WST.2015.254
Abstract: The present study evaluates effectiveness of up-flow anaerobic sludge blanket (UASB) reactor followed by two post-anaerobic treatment options, namely free-surface, up-flow constructed wetland (FUP-CW) and oxygen-limited anaerobic nitrification/denitrification (OLAND) processes in treating sewage from the peri-urban areas in India receiving illegal industrial infiltrations. The UASB studies yielded robust results towards fluctuating strength of sewage and consistently removed 87-98% chemical oxygen demand (COD) at a hydraulic retention time of 1.5-2 d. The FUP-CW removed 68.5 +/- 13% COD, 68 +/- 3% NH4+-N, 38 +/- 5% PO43--P, 97.6 +/- 5% suspended particles and 97 +/- 13% fecal coliforms. Nutrient removal was found to be limiting in FUP-CW, especially in winter. Nitrogen removal in the OLAND process were 100 times higher than the FUP-CW process. Results show that UASB followed by FUP-CW can be an excellent, decentralized sewage treatment option, except during winter when nutrient removal is limited in FUP-CW. Hence, the study proposes bio-augmentation of FUP-CW with OLAND biomass for overall improvement in the performance of UASB followed by FUP-CW process.
Keywords: A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.2166/WST.2015.254
|
“Hysteresis and parent-metabolite analyses unravel characteristic pesticide transport mechanisms in a mixed land use catchment”. Tang T, Stamm C, van Griensven A, Seuntjens P, Bronders J, Water research 124, 663 (2017). http://doi.org/10.1016/J.WATRES.2017.08.016
Abstract: To properly estimate and manage pesticide occurrence in urban rivers, it is essential, but often highly challenging, to identify the key pesticide transport pathways in association to the main sources. This study examined the concentration-discharge hysteresis behaviour (hysteresis analysis) for three pesticides and the parent-metabolite concentration dynamics for two metabolites at sites with different levels of urban influence in a mixed land use catchment (25 km(2)) within the Swiss Greifensee area, aiming to identify the dominant pesticide transport pathways. Combining an adapted hysteresis classification framework with prior knowledge of the field conditions and pesticide usage, we demonstrated the possibility of using hysteresis analysis to qualitatively infer the dominant pesticide transport pathway in mixed land-use catchments. The analysis showed that hysteresis types, and therefore the dominant transport pathway, vary among pesticides, sites and rainfall events. Hysteresis loops mostly correspond to dominant transport by flow components with intermediate response time, although pesticide sources indicate that fast transport pathways are responsible in most cases (e.g. urban runoff and combined sewer overflows). The discrepancy suggests the fast transport pathways can be slowed down due to catchment storages, such as topographic depressions in agricultural areas, a wastewater treatment plant (WWTP) and other artificial storage units (e.g. retention basins) in urban areas. Moreover, the WWTP was identified as an important factor modifying the parent-metabolite concentration dynamics during rainfall events. To properly predict and manage pesticide occurrence in catchments of mixed land uses, the hydrological delaying effect and chemical processes within the artificial structures need to be accounted for, in addition to the catchment hydrology and the diversity of pesticide sources. This study demonstrates that in catchments with diverse pesticide sources and complex transport mechanisms, the adapted hysteresis analysis can help to improve our understanding on pesticide transport behaviours and provide a basis for effective management strategies.(C) 2017 Elsevier Ltd. All rights reserved.
Keywords: A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1016/J.WATRES.2017.08.016
|
“Combining multi-receiver electromagnetic induction and stepped frequency ground penetrating radar for industrial site investigation”. Van De Vijver E, Van Meirvenne M, Saey T, Delefortrie S, De Smedt P, De Pue J, Seuntjens P, European journal of soil science 66, 688 (2015). http://doi.org/10.1111/EJSS.12229
Abstract: The soil at industrial sites is frequently characterized by very heterogeneous properties, which are often related to physical disturbance and contamination. A conventional approach to characterize the soil, with only a limited number of invasive observations, fails to capture the full extent of soil heterogeneity. Proximal soil sensing provides efficient tools to record spatially dense soil information. Nevertheless, because the output of most sensors is affected by more than one soil property, the simultaneous characterization of different soil properties requires the use of multiple sensors. Here, we apply multi-receiver electromagnetic induction (EMI) and stepped frequency ground penetrating radar (GPR) to survey a former gasworks site in a seaport area of Belgium. We used the EMI and GPR sensors in a motorized system to obtain densely sampled measurements of apparent electrical conductivity, apparent magnetic susceptibility and contrasts in relative dielectric permittivity. Our study shows that the sensors give detailed information on the variation in these electromagnetic soil properties. Interpretation of the variation in terms of the stratification of the soil was hampered by localized anthropogenic disturbances. However, the sensors provided complementary information that enabled the identification, discrimination and accurate location of several of these localized disturbances, including underground utility services such as electric cables, buried structures such as the remains of foundations and contamination by salts. Because these represent typical targets in industrial site investigation, we conclude that multi-receiver EMI and stepped frequency GPR provide a useful set of tools to expedite the investigation of industrial sites.
Keywords: A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1111/EJSS.12229
|
“Biotemplated diatom silica-titania materials for air purification”. Van Eynde E, Tytgat T, Smits M, Verbruggen SW, Hauchecorne B, Lenaerts S, Photochemical &, photobiological sciences 12, 690 (2013). http://doi.org/10.1039/C2PP25229E
Abstract: We present a novel manufacture route for silicatitania photocatalysts using the diatom microalga Pinnularia sp. Diatoms self-assemble into porous silica cell walls, called frustules, with periodic micro-, meso- and macroscale features. This unique hierarchical porous structure of the diatom frustule is used as a biotemplate to incorporate titania by a solgel methodology. Important material characteristics of the modified diatom frustules under study are morphology, crystallinity, surface area, pore size and optical properties. The produced biosilicatitania material is evaluated towards photocatalytic activity for NOx abatement under UV radiation. This research is the first step to obtain sustainable, well-immobilised silicatitania photocatalysts using diatoms.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 2.344
Times cited: 18
DOI: 10.1039/C2PP25229E
|
“Immobilization of TiO2 into self-supporting photocatalytic foam : influence of calcination temperature”. Tytgat T, Smits M, Lenaerts S, Verbruggen SW, International journal of applied ceramic technology 11, 714 (2014). http://doi.org/10.1111/IJAC.12086
Abstract: Immobilization of photocatalytic powder is crucial to obtain industrially relevant purification processes. To achieve this goal, self-supporting TiO2 foams were manufactured by a polyacrylamide gel process. These gels were calcined at different temperatures to study the effect of the calcination temperature on foam characteristics (rigidity, crystallinity, and porosity) and its influence on photocatalytic activity. The results show that an optimal degradation is achieved for those foams calcined between 700 and 800°C. Calcination at higher temperatures results in a steep decrease in activity, explained by stability issues of the material due to formation of Na2SO4 phases and a larger rutile fraction.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 1.048
Times cited: 2
DOI: 10.1111/IJAC.12086
|
“A general leaf area geometric formula exists for plants evidence from the simplified Gielis equation”. Shi P, Ratkowsky DA, Li Y, Zhang L, Lin S, Gielis J, Forests (19994907) 9, 714 (2018). http://doi.org/10.3390/F9110714
Abstract: Plant leaves exhibit diverse shapes that enable them to utilize a light resource maximally. If there were a general parametric model that could be used to calculate leaf area for different leaf shapes, it would help to elucidate the adaptive evolutional link among plants with the same or similar leaf shapes. We propose a simplified version of the original Gielis equation (SGE), which was developed to describe a variety of object shapes ranging from a droplet to an arbitrary polygon. We used this equation to fit the leaf profiles of 53 species (among which, 48 bamboo plants, 5 woody plants, and 10 geographical populations of a woody plant), totaling 3310 leaves. A third parameter (namely, the floating ratio c in leaf length) was introduced to account for the case when the theoretical leaf length deviates from the observed leaf length. For most datasets, the estimates of c were greater than zero but less than 10%, indicating that the leaf length predicted by the SGE was usually smaller than the actual length. However, the predicted leaf areas approximated their actual values after considering the floating ratios in leaf length. For most datasets, the mean percent errors of leaf areas were lower than 6%, except for a pooled dataset with 42 bamboo species. For the elliptical, lanceolate, linear, obovate, and ovate shapes, although the SGE did not fit the leaf edge perfectly, after adjusting the parameter c, there were small deviations of the predicted leaf areas from the actual values. This illustrates that leaves with different shapes might have similar functional features for photosynthesis, since the leaf areas can be described by the same equation. The anisotropy expressed as a difference in leaf shape for some plants might be an adaptive response to enable them to adapt to different habitats.
Keywords: A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.3390/F9110714
|
“Comparison of seed morphology of two ginkgo cultivars”. Tian F, Wang Y, Sandhu HS, Gielis J, Shi P, Journal Of Forestry Research 31, 751 (2020). http://doi.org/10.1007/S11676-018-0770-Y
Abstract: Ginkgo biloba L. is a precious relic tree species with important economic value. Seeds, as a vital reproductive organ of plants, can be used to distinguish cultivars of the species. We chose 400 seeds from two cultivars of ginkgo (Fozhi and Maling; 200 seeds for each cultivar) as the study material and used the Gielis equation to fit the projected shape of these seeds. The coefficients of variation (CV) in root mean squared errors (RMSE) obtained from the fitted data were used to compare the level of inter-cultivar variations in seed shape. We also used the covariance analysis to compare the allometric relationships between seed weights and projected areas of these two cultivars. The Gielis equation fitted well the seed shapes of two ginkgo cultivars. The lower CV in RMSE of cultivar Fozhi than Maling indicated a less symmetrical seed shape in the latter than the former. The bootstrap percentile method showed that the seed shape differences between the two cultivars were significant. However, there was no significant difference in the exponents between the seed weights and the projected areas of these two cultivars. Overall, the significant differences in shapes between the seeds of two ginkgo cultivars were well explained by the Gielis equation; this model can be further extended to compare morphological differences in other ginkgo cultivars, and even for plant seeds or animal eggs that have similar oval shapes.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 3
Times cited: 3
DOI: 10.1007/S11676-018-0770-Y
|
“Light-induced processes in plasmonic Gold/TiO2 photocatalysts studied by electron paramagnetic resonance”. Caretti I, Keulemans M, Verbruggen SW, Lenaerts S, Van Doorslaer S, Topics in catalysis 58, 776 (2015). http://doi.org/10.1007/S11244-015-0419-4
Abstract: X-band and W-band continuous-wave (CW) electron paramagnetic resonance (EPR) was used to study in situ light-induced (LI) mechanisms in commercial P90 titania (90 % anatase/10 % rutile) compared to plasmon-enhanced Au-P90 photocatalyst. These materials were excited using UV and 532 nm visible light to generate different excitation states and distinguish pure charge separation from plasmon-assisted resonance processes. Up to nine different photoinduced species of trapped electrons and holes were identified. LI CW EPR of P90 is presented for the first time, showing a UV excitation response similar to the well-known mixed-phase P25 titania. It is shown that incorporation of Au nanoparticles in Au-P90 and formation of a Schottky junction affects the charge separation state of the catalyst under UV light. Moreover, Au impregnation activated P90 through plasmon hot electron injection under visible light excitation (plasmonic sensitization effect). In general, EPR proved to be crucial to determine the different photoexciation paths and reactions that regulate plasmonic photocatalysis.
Keywords: A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 2.486
Times cited: 22
DOI: 10.1007/S11244-015-0419-4
|
“The scaling relationships of leaf biomass vs. leaf surface area of 12 bamboo species”. Huang W, Su X, Ratkowsky DA, Niklas KJ, Gielis J, Shi P, Global ecology and conservation 20, e00793 (2019). http://doi.org/10.1016/J.GECCO.2019.E00793
Abstract: There is convincing evidence for a scaling relationship between leaf dry weight (DW) and leaf surface area (A) for broad-leaved plants, and most estimates of the scaling exponent of DW vs. A are greater than unity. However, the scaling relationship of leaf fresh weight (FW) vs. A has been largely neglected. In the present study, we examined whether there is a statistically strong scaling relationship between FW and A and compared the goodness of fit to that of DW vs. A. Between 250 and 520 leaves from each of 12 bamboo species within 2 genera (Phyllostachys and Pleioblastus) were investigated. The reduced major axis regression protocols were used to determine scaling relationships. The fit for the linearized scaling relationship of FW vs. A was compared with that of DW vs. A using the coefficient of determination (i.e., r2). A stronger scaling relationship between FW and A than that between DW and A was observed for each of the 12 bamboo species investigated. Among the 12 species examined, five had significantly smaller scaling exponents of FW vs. A compared to those of DW vs. A; only one species had a scaling exponent of FW vs. A greater than that of DW vs. A. No significant difference between the two scaling exponents was observed for the remaining 6 species. Researchers conducting future studies might be well advised to consider the influence of leaf fresh weight when exploring the scaling relationships of foliar biomass allocation patterns.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1016/J.GECCO.2019.E00793
|
“CFD investigation of a multi-tube photocatalytic reactor in non-steady-state conditions”. van Walsem J, Verbruggen SW, Modde B, Lenaerts S, Denys S, Chemical engineering journal 304, 808 (2016). http://doi.org/10.1016/J.CEJ.2016.07.028
Abstract: A novel multi-tube photoreactor is presented with a high efficiency (over 90% conversion) toward the degradation of acetaldehyde in air under UV conditions with an incident intensity of 2.1 mW cm−2. A CFD model was developed to simulate the transient adsorption and photocatalytic degradation processes of acetaldehyde in this reactor design and to estimate the corresponding kinetic parameters through an optimization routine using the experimentally determined outlet concentration profiles. The CFD model takes into account the entire reactor geometry and all relevant flow parameters, in contrast to analytical methods that often oversimplify the physical and chemical process characteristics. Using CFD, we show that both adsorption and desorption rate constants increase by respectively one and two orders of magnitude when the UV light is switched on, which clearly affects the transient behavior. The agreement of the experimental and modelled concentration profiles is excellent as evidenced by a coefficient of determination of at least 0.965. To demonstrate the reliability and accuracy of all parameters obtained from the modelling approach, an ultimate validation test was performed using other conditions than the ones used for estimating the kinetic parameters. The model was able to accurately simulate simultaneous adsorption, desorption and photocatalytic degradation.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 6.216
Times cited: 10
DOI: 10.1016/J.CEJ.2016.07.028
|
“Gas phase photocatalytic spiral reactor for fast and efficient pollutant degradation”. Blommaerts N, Asapu R, Claes N, Bals S, Lenaerts S, Verbruggen SW, Chemical engineering journal 316, 850 (2017). http://doi.org/10.1016/j.cej.2017.02.038
Abstract: Photocatalytic reactors for the degradation of gaseous organic pollutants often suffer from major limitations such as small reaction area, sub-optimal irradiation conditions and thus limited reaction rate. In this work, an alternative solution is presented that involves a glass tube coated on the inside with (silvermodified) TiO2 and spiraled around a UVA lamp. First, the spiral reactor is coated from the inside with TiO2 using an experimentally verified procedure that is optimized toward UV light transmission. This procedure is kept as simple as possible and involves a single casting step of a 1 wt% suspension of TiO2 in ethanol through the spiral. This results in a coated tube that absorbs nearly all incident UV light under the experimental conditions used. The optimized coated spiral reactor is then benchmarked to a conventional annular photoreactor of the same outer dimensions and total catalyst loading over a broad range of experimental conditions. Although residence time distribution experiments indicate slightly longer dwelling of molecules in the spiral reactor, no significant difference in by-passing of gas between the spiral reactor and the annular reactor can be claimed. Acetaldehyde degradation efficiency of 100% is obtained with the spiral reactor for a residence time as low as 60 s, whereas the annular reactor could not achieve full degradation even at 1000 s residence time. In a final case study, addition of long-term stable silver nanoparticles, protected by an ultra-thin polymer shell applied via the layer-by-layer (LbL) method, to the spiral reactor coating is shown to double the degradation efficiency and provides an interesting strategy to cope with higher pollutant concentrations without changing the overall dimensions.
Keywords: A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT); Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 6.216
Times cited: 30
DOI: 10.1016/j.cej.2017.02.038
|
“Combined effects of blockage and yield stress on drag and heat transfer from an in-line array of three spheres”. Dasgupta N, Borah R, Mishra P, Gupta AK, Chhabra RP, Journal of dispersion science and technology 40, 855 (2019). http://doi.org/10.1080/01932691.2018.1485581
Abstract: This work reports results on the drag and heat transfer from an in-line array of three isothermal spheres falling in a cylindrical confinement filled with Bingham plastic fluids. The effects of dimensionless parameters, such as the Reynolds number (1 ≤ Re ≤ 100), Prandtl number (1 ≤ Pr ≤ 100), Bingham number (0 ≤ Bn ≤ 100), blockage ratio (2 ≤ β ≤ 4) and sphere-to-sphere distance (1.5 ≤ t ≤ 6) have been elucidated. The flow and heat transfer characteristics were analysed in terms of yielded/unyielded regions, streamline and isotherm contours, drag coefficient, pressure coefficient, and local and average Nusselt number. Broadly, the drag coefficient shows a positive dependence on Bn and sphere-to-sphere distance (t) while it exhibits an inverse dependence on Re and β. On the other hand, the Nusselt number shows a positive dependence on Re, Pr, Bn and β; and a complex dependence on t for each sphere. Simple predictive expressions for the average Nusselt number for each sphere are formulated, thereby enabling its prediction in a new application.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1080/01932691.2018.1485581
|
“Model-based scenario analysis of the impact of remediation measures on metal leaching from soils contaminated by historic smelter emissions”. Joris I, Bronders J, van der Grift B, Seuntjens P, Journal of environmental quality 43, 859 (2014). http://doi.org/10.2134/JEQ2013.07.0287
Abstract: A spatially distributed model for leaching of Cd from the unsaturated zone was developed for the Belgian-Dutch transnational Kempen region. The model uses as input land-use maps, atmospheric deposition data, and soil data and is part of a larger regional model that simulates transport of Cd in soil, groundwater, and surface water. A new method for deriving deposition from multiple sites was validated using soil data in different wind directions. Leaching was calculated for the period 1890 to 2010 using a reconstruction of metal loads in the region. The model was able to reproduce spatial patterns of concentrations in soil and groundwater and predicted the concentration in shallow groundwater adequately well for the purpose of evaluating management options. For 42% of the data points, measurements and calculations were within the same concentration class. The model was used for forecasting under a reference scenario, an autonomous development scenario including climate change, and a scenario with implementation of remediation measures. The impact of autonomous development (under the most extreme scenario of climatic change) amounted to an increase of 10% in cumulative Cd flux after 100 yr as compared with the reference scenario. The impact of remediation measures was mainly local and is less pronounced (i.e., only 3% change in cumulative flux at the regional scale). The integrated model served as a tool to assist in developing management strategies and prioritization of remediation of the wide-spread heavy metal contamination in the region.
Keywords: A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.2134/JEQ2013.07.0287
|
“Determining groundwater-surface water exchange from temperature-time series : combining a local polynomial method with a maximum likelihood estimator”. Vandersteen G, Schneidewind U, Anibas C, Schmidt C, Seuntjens P, Batelaan O, Water resources research 51, 922 (2015). http://doi.org/10.1002/2014WR015994
Abstract: The use of temperature-time series measured in streambed sediments as input to coupled water flow and heat transport models has become standard when quantifying vertical groundwater-surface water exchange fluxes. We develop a novel methodology, called LPML, to estimate the parameters for 1-D water flow and heat transport by combining a local polynomial (LP) signal processing technique with a maximum likelihood (ML) estimator. The LP method is used to estimate the frequency response functions (FRFs) and their uncertainties between the streambed top and several locations within the streambed from measured temperature-time series data. Additionally, we obtain the analytical expression of the FRFs assuming a pure sinusoidal input. The estimated and analytical FRFs are used in an ML estimator to deduce vertical groundwater-surface water exchange flux and its uncertainty as well as information regarding model quality. The LPML method is tested and verified with the heat transport models STRIVE and VFLUX. We demonstrate that the LPML method can correctly reproduce a priori known fluxes and thermal conductivities and also show that the LPML method can estimate averaged and time-variable fluxes from periodic and nonperiodic temperature records. The LPML method allows for a fast computation of exchange fluxes as well as model and parameter uncertainties from many temperature sensors. Moreover, it can utilize a broad frequency spectrum beyond the diel signal commonly used for flux calculations.
Keywords: A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1002/2014WR015994
|
“Sustainability appraisal tools for soil and groundwater remediation : how is the choice of remediation alternative influenced by different sets of sustainability indicators and tool structures?”.Beames A, Broekx S, Lookman R, Touchant K, Seuntjens P, The science of the total environment 470, 954 (2014). http://doi.org/10.1016/J.SCITOTENV.2013.10.044
Abstract: The state-of-the-science in sustainability assessment of soil and groundwater remediation is evaluated with the application of four decision support systems (DSSs) to a large-scale brownfield revitalization case study. The DSSs were used to perform sustainability appraisals of four technically feasible remediation alternatives proposed for the site. The first stage of the review compares the scope of each tool's sustainability indicators, how these indicators are measured and how the tools differ in terms of standardization and weighting procedures. The second stage of the review compares the outputs from the tools and determines the key factors that result in differing results between tools. The evaluation of indicator sets and tool structures explains why the tools generate differing results. Not all crucial impact areas, as identified by sustainable remediation forums, are thoroughly considered by the tools, particularly with regard to the social and economic aspects of sustainability. Variations in boundary conditions defined between technologies, produce distorted environmental impact results, especially when in-situ and ex-situ technologies are compared. The review draws attention to the need for end users to be aware of which aspects of sustainability are considered, how the aspects are measured and how all aspects are ultimately balanced in the evaluation of potential remediation strategies. Existing tools can be improved by considering different technologies within the same boundary conditions and by expanding indicator sets to include indicators deemed to be relevant by remediation forums. (C) 2013 Elsevier B.V. All rights reserved.
Keywords: A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1016/J.SCITOTENV.2013.10.044
|
“Modeling electron competition among nitrogen oxides reduction and N2Oaccumulation in hydrogenotrophic denitrification”. Liu Y, Ngo HH, Guo W, Peng L, Chen X, Wang D, Pan Y, Ni B-J, Biotechnology and bioengineering 115, 978 (2018). http://doi.org/10.1002/BIT.26512
Abstract: Hydrogenotrophic denitrification is a novel and sustainable process for nitrogen removal, which utilizes hydrogen as electron donor, and carbon dioxide as carbon source. Recent studies have shown that nitrous oxide (N2O), a highly undesirable intermediate and potent greenhouse gas, can accumulate during this process. In this work, a new mathematical model is developed to describe nitrogen oxides dynamics, especially N2O, during hydrogenotrophic denitrification for the first time. The model describes electron competition among the four steps of hydrogenotrophic denitrification through decoupling hydrogen oxidation and nitrogen reduction processes using electron carriers, in contrast to the existing models that couple these two processes and also do not consider N2O accumulation. The developed model satisfactorily describes experimental data on nitrogen oxides dynamics obtained from two independent hydrogenotrophic denitrifying cultures under various hydrogen and nitrogen oxides supplying conditions, suggesting the validity and applicability of the model. The results indicated that N2O accumulation would not be intensified under hydrogen limiting conditions, due to the higher electron competition capacity of N2O reduction in comparison to nitrate and nitrite reduction during hydrogenotrophic denitrification. The model is expected to enhance our understanding of the process during hydrogenotrophic denitrification and the ability to predict N2O accumulation.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1002/BIT.26512
|