|
“Selective recovery of Cr from stainless steel slag by alkaline roasting followed by water leaching”. Kim E, Spooren J, Broos K, Horckmans L, Quaghebeur M, Vrancken KC, Hydrometallurgy 158, 139 (2015). http://doi.org/10.1016/J.HYDROMET.2015.10.024
Abstract: Selective chromium (Cr) leaching from stainless steel slag (SS slag) by alkali roasting followed by water leaching was investigated. The efficiency of the alkali roasting process for Cr leaching was increased by optimizing the mass ratio of alkaline agents (NaOH, and NaOH-NaNO3) to the slag, roasting temperature and time. At the optimum condition (0.67 mass ratio of NaOH to SS slag, 400 degrees C, 2 h) of NaOH roasting, chromium leaching was around 83%, while the matrix material was dissolved only to a limited extent (Si 8.0%). Mechanical activation of the SS slag prior to roasting reduced the optimum NaOH to SS slag mass ratio to 0.4. The addition of NaNO3 as an oxidant to the NaOH salt increased Cr leaching to 89% after roasting at 400 degrees C for 2 h. The remaining Cr phases in the residue were almost exclusively FeCr alloys. Further chromium dissolution from these alloys is prevented by a passivation layer of Fe oxides as shown by SEM/EDS images. Based on these results, a SS slag recycling process is suggested in which roasting-water leaching followed by water washing to remove Cr yields a residue which has potential for application as a construction material. (C) 2015 Elsevier B.V. All rights reserved.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1016/J.HYDROMET.2015.10.024
|
|
“Determinants of risk behaviour : effects of perceived risks and risk attitude on farmer's adoption of risk management strategies”. van Winsen F, de Mey Y, Lauwers L, Van Passel S, Vancauteren M, Wauters E, Journal Of Risk Research 19, 56 (2016). http://doi.org/10.1080/13669877.2014.940597
Abstract: The importance of risk perception and risk attitude for understanding individual's risk behaviour are independently well described in literature, but rarely combined in an integrated approach. In this study, we propose a model assuming the choice to implement certain risk management strategies to be directly driven by both perceptions of risks and risk attitude. Other determinants influence the intention to apply different risk strategies mainly indirectly, mediated by risk perception and risk attitude. This conceptual model is empirically tested, using structural equation modelling, for understanding the intention of farmers to implement different common risk management strategies at their farms. Data are gathered in a survey completed by 500 farmers from the Flanders region in Belgium, investigating attitudes towards farming, perceived past exposure to risk, socio-demographic characteristics, farm size, perceptions of the major sources of farm business risk, risk attitudes and the intention to apply common risk management strategies. Our major findings are: (i) perception of major farm business risks have no significant impact on the intention of applying any of the risk strategies under study, (ii) risk attitude does have a significant impact. Therefore, rather than objective risk faced and the subjective interpretation thereof, it is the general risk attitude that influence intended risk strategies to be implemented. A distinction can be made between farmers willing to take risk, who are more inclined to apply ex-ante risk management strategies and risk averse farmers who are less inclined to implement ex-ante risk management strategies but rather cope with the consequences and diminish their effects ex-post when risks have occurred.
Keywords: A1 Journal article; Sociology; Engineering Management (ENM)
Impact Factor: 1.34
Times cited: 25
DOI: 10.1080/13669877.2014.940597
|
|
“The perception by pastoralists of the factors influencing the appropriate distribution of livestock in the rangelands of north-east Iran”. Shahraki MR, Abedi-Sarvestani A, Seyedi MS, Rafiaani Khachak P, Nieto-Garibay A, Van Passel S, Azadi A, The Rangeland Journal 37, 191 (2015). http://doi.org/10.1071/RJ14027
Abstract: The distribution of livestock grazing is a key principle of range management. This study examines pastoralists perceptions of the factors that affect the distribution of livestock in the rangelands of the Neqab region of the Kashmar County in north-east Iran. Data were collected from the pastoralists on their perceptions of the managerial, biological and physical factors that influences the distribution of livestock, using both qualitative and quantitative assessments. Results showed that, the perception of the majority of pastoralists was that the distribution of livestock was average or good in the study area. It was perceived that the experience of herders and the size of the rangeland were the main factors influencing the distribution of livestock. Regression analyses showed that it was perceived that managerial factors had a more important role than biological and physical factors in the distribution of livestock and the proper use of the rangelands in north-east Iran.
Keywords: A1 Journal article; Economics; Engineering Management (ENM)
DOI: 10.1071/RJ14027
|
|
“Assessment of environmental and economic feasibility of Enhanced Landfill Mining”. Danthurebandara M, Van Passel S, Vanderreydt I, Van Acker K, Waste Management 45, 434 (2015). http://doi.org/10.1016/J.WASMAN.2015.01.041
Abstract: This paper addresses the environmental and economic performance of Enhanced Landfill Mining (ELFM). Based on life cycle assessment and life cycle costing, a detailed model is developed and is applied to a case study, i.e. the first ELFM project in Belgium. The environmental and economic analysis is performed in order to study the valorisation of different waste types in the landfill, such as municipal solid waste, industrial waste and total waste. We found that ELFM is promising for the case study landfill as greater environmental benefits are foreseen in several impact categories compared to the landfills current situation (the Do-nothing scenario). Among the considered processes, the thermal treatment process dominates both the environmental and economic performances of ELFM. Improvements in the electrical efficiency of thermal treatment process, the calorific value of refuse derived fuel and recovery efficiencies of different waste fractions lead the performance of ELFM towards an environmentally sustainable and economically feasible direction. Although the environmental and economic profiles of ELFM will differ from case to case, the results of this analysis can be used as a benchmark for future ELFM projects.
Keywords: A1 Journal article; Economics; Engineering Management (ENM)
Impact Factor: 4.03
Times cited: 30
DOI: 10.1016/J.WASMAN.2015.01.041
|
|
“Innovative market-based policy instruments for waste management : a case study on shredder residues in Belgium”. Dubois M, Hoogmartens R, Van Passel S, Van Acker K, Vanderreydt I, Waste Management &, Research 33, 886 (2015). http://doi.org/10.1177/0734242X15600053
Abstract: In an increasingly complex waste market, market-based policy instruments, such as disposal taxes, can give incentives for sustainable progress while leaving flexibility for innovation. However, implementation of disposal taxes is often criticised by domestic waste handlers that fear to be outcompeted by competitors in other countries. The article discusses three innovative market-based instruments that limit the impact on international competitiveness: Tradable recycling credits, refunded disposal taxes and differentiated disposal taxes. All three instruments have already been implemented for distinct environmental policies in Europe. In order to illustrate how these instruments can be used for waste policy, the literature review is complemented with a case study on shredder residues from metal-containing waste streams in Belgium. The analysis shows that a conventional disposal tax remains the most efficient, simple and transparent instrument. However, if international competition is a significant issue or if political support is weak, refunded and differentiated disposal taxes can have an added value as second-best instruments. Tradable recycling credits are not an appropriate instrument for use in small waste markets with market power. In addition, refunded taxes create similar incentives, but induce lower transactions costs.
Keywords: A1 Journal article; Economics; Engineering Management (ENM)
Impact Factor: 1.803
Times cited: 1
DOI: 10.1177/0734242X15600053
|
|
“Environmental and economic performance of plasma gasification in Enhanced Landfill Mining”. Danthurebandara M, Van Passel S, Vanderreydt I, Van Acker K, Waste Management 45, 458 (2015). http://doi.org/10.1016/J.WASMAN.2015.06.022
Abstract: This paper describes an environmental and economic assessment of plasma gasification, one of the viable candidates for the valorisation of refuse derived fuel from Enhanced Landfill Mining. The study is based on life cycle assessment and life cycle costing. Plasma gasification is benchmarked against conventional incineration, and the study indicates that the process could have significant impact on climate change, human toxicity, particulate matter formation, metal depletion and fossil depletion. Flue gas emission, oxygen usage and disposal of residues (plasmastone) are the major environmental burdens, while electricity production and metal recovery represent the major benefits. Reductions in burdens and improvements in benefits are found when the plasmastone is valorised in building materials instead of landfilling. The study indicates that the overall environmental performance of plasma gasification is better than incineration. The study confirms a trade-off between the environmental and economic performance of the discussed scenarios. Net electrical efficiency and investment cost of the plasma gasification process and the selling price of the products are the major economic drivers.
Keywords: A1 Journal article; Economics; Engineering sciences. Technology; Engineering Management (ENM)
Impact Factor: 4.03
Times cited: 12
DOI: 10.1016/J.WASMAN.2015.06.022
|
|
“Sustainability indicators of irans developmental plans : application of the sustainability compass theory”. Mahdei KN, Pouya M, Taheri F, Azadi H, Van Passel S, Sustainability 7, 14647 (2015). http://doi.org/10.3390/SU71114647
Abstract: The main purpose of this study was to analyze Irans developmental plans in order to examine and compare their direction and conformity with the sustainable development theory via the compass of sustainability. The approach involves a content analysis used in line with qualitative research methodologies. The results indicated that, in the first developmental plans, there was no direct reference to sustainable development. In the second to fifth plans, the main focus was on the social, environmental, and economic dimensions of development; which were common elements seen in the policies of all the plans. An analysis of the fourth plan revealed that expressions related to sustainable development appeared more frequently, indicating a stronger emphasis on sustainable development by decision-makers.
Keywords: A1 Journal article; Economics; Engineering Management (ENM)
Impact Factor: 1.789
Times cited: 3
DOI: 10.3390/SU71114647
|
|
“Safe use of metal-contaminated agricultural land by cultivation of energy maize (Zea mays)”. Van Slycken S, Witters N, Meers E, Peene A, Michels E, Adriaensen K, Ruttens A, Vangronsveld J, Du Laing G, Wierinck I, Van Dael M, Van Passel S, Tack FMG, Environmental Pollution 178, 375 (2013). http://doi.org/10.1016/J.ENVPOL.2013.03.032
Abstract: Production of food crops on trace element-contaminated agricultural lands in the Campine region (Belgium) can be problematic as legal threshold values for safe use of these crops can be exceeded. Conventional sanitation of vast areas is too expensive and alternatives need to be investigated. Zea mays on a trace element-contaminated soil in the region showed an average yield of 53 ± 10 Mg fresh or 20 ± 3 Mg dry biomass ha−1. Whole plant Cd concentrations complied with legal threshold values for animal feed. Moreover, threshold values for use in anaerobic digestion were met. Biogas production potential did not differ between maize grown on contaminated and non-contaminated soils. Results suggested favorable perspectives for farmers to generate non-food crops profitably, although effective soil cleaning would be very slow. This demonstrates that a valuable and sustainable alternative use can be generated for moderately contaminated soils on which conventional agriculture is impaired.
Keywords: A1 Journal article; Economics
Impact Factor: 5.099
Times cited: 30
DOI: 10.1016/J.ENVPOL.2013.03.032
|
|
“Alteration of fossil-bearing shale (Autun, France, Permian), part II : monitoring artificial and natural ageing by combined use of S and Ca K-edge XANES analysis, Rock-Eval pyrolysis and FTIR analysis”. Odin GP, Vanmeert F, Farges F, Gand G, Janssens K, Romero-Sarmiento M-F, Steyer JS, Vantelon D, Rouchon V, Annales de paléontologie 101, 225 (2015). http://doi.org/10.1016/J.ANNPAL.2015.03.001
Abstract: Fossil-bearing shale specimens that include sulfides in their compositions are chemically reactive and sometimes also mechanically fragile. This decay is often related to iron sulfate efflorescence resulting from the oxidation of sulfide compounds. The processes underlying these degradations are poorly known, thus impeding the elaboration of curative or preventive treatments. The present contribution aims to identify the origin of museum specimen alterations. It focuses on the Flouest collection housed at the Museum National d'Histoire Naturelle (MNHN, Paris, France) and originating from the Autun Basin (Saone-et-Loire, France, Permian). To evaluate the alteration of MNHN specimens, it appeared necessary to compare their composition with that of unaltered shale so as to identify chemical changes occurring during ageing. Therefore, new material was collected in the Autun Basin, among others on the locality of Muse that corresponds to the same lithostratigraphic unit as that of the MNHN specimens. This material was, if necessary, artificially aged. The first part of this work, presented elsewhere, deals with the use of Xray diffraction and Mossbauer spectroscopy for characterizing iron reactivity and speciation. It leads to the conclusion that the reactivity of iron in the shale matrix was limited and could not account for the large efflorescence of iron (II) sulfate occurring nearby the fossil. The second part presented here focuses on the use of S K-edge X-ray Absorption Near Edge Structure (XANES) spectroscopy for characterizing sulfur speciation and reactivity. Measurements were performed on the shale matrix and on thin layers of maceral found in the proximity of damaged areas. As sulfur may be found in association with calcium or organic matter, complementary techniques were implemented, such as FTIR spectroscopy, Rock-Eval pyrolysis (characterization of organic matter content) and Ca K-edge XANES (analysis of calcium speciation) spectroscopy. It was shown that sulfur is mainly related to thioether, sulfoxide, iron sulfide, and sulfates whereas calcium is mainly bound to carboxylate, carbonate and/or sulfate groups. FTIR analysis of the macerals confirmed the presence of vitrinite on damaged MNHN specimens. The low oxygen content of new shale samples determined by Rock-Eval pyrolysis indicates that the organic matter is well preserved, despite the fact that samples come from outcrop surface. In the newly collected material, sulfur is mainly related to organic sulfides (thioether) with a minor occurrence of iron sulfide. In the shale fraction of damaged MNHN specimens, sulfur is mostly oxidized into a mixture of iron and calcium sulfate. However, in the vitrinite layers of the same specimens, a large proportion of sulfur corresponds to organic sulfides. Also the oxidation of sulfur does not occur homogeneously but preferentially in the shale fraction, probably because this latter is porous whereas vitrinite is not. Artificial ageing of new shale material showed that the oxidation of organic sulfides could be reproduced at 90 degrees C, 80% of relative humidity. However, the obtained efflorescence almost exclusively corresponds to calcium sulfate whereas iron (II) sulfates are mostly observed on MNHN specimens. The new material collected on site is probably to be questioned, and future studies will have to select new samples with fossil remains. This will be the object of the third part of this work. (C) 2015 Elsevier Masson SAS. All rights reserved.
Keywords: A1 Journal article; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation)
Impact Factor: 1.113
Times cited: 6
DOI: 10.1016/J.ANNPAL.2015.03.001
|
|
“A redox signalling globin is essential for reproduction in Caenorhabditis elegans”. De Henau S, Tilleman L, Vangheel M, Luyckx E, Trashin S, Pauwels M, Germani F, Vlaeminck C, Vanfleteren JR, Bert W, Pesce A, Nardini M, Bolognesi M, De Wael K, Moens L, Dewilde S, Braeckman BP, Nature communications 6, 8782 (2015). http://doi.org/10.1038/NCOMMS9782
Abstract: Moderate levels of reactive oxygen species (ROS) are now recognized as redox signalling molecules. However, thus far, only mitochondria and NADPH oxidases have been identified as cellular sources of ROS in signalling. Here we identify a globin (GLB-12) that produces superoxide, a type of ROS, which serves as an essential signal for reproduction in C. elegans. We find that GLB-12 has an important role in the regulation of multiple aspects in germline development, including germ cell apoptosis. We further describe how GLB-12 displays specific molecular, biochemical and structural properties that allow this globin to act as a superoxide generator. In addition, both an intra- and extracellular superoxide dismutase act as key partners of GLB-12 to create a transmembrane redox signal. Our results show that a globin can function as a driving factor in redox signalling, and how this signal is regulated at the subcellular level by multiple control layers.
Keywords: A1 Journal article; Engineering sciences. Technology; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation)
Impact Factor: 12.124
Times cited: 20
DOI: 10.1038/NCOMMS9782
|
|
“Polydopamine-gelatin as universal cell-interactive coating for methacrylate-based medical device packaging materials : when surface chemistry overrules substrate bulk properties”. Van de Walle E, Van Nieuwenhove I, Vanderleyden E, Declercq H, Gellynck K, Schaubroeck D, Ottevaere H, Thienpont H, De Vos WH, Cornelissen M, Van Vlierberghe S, Dubruel P, Biomacromolecules 17, 56 (2016). http://doi.org/10.1021/ACS.BIOMAC.5B01094
Abstract: Despite its widespread application in the fields of ophthalmology, orthopedics and dentistry and the stringent need for polymer packagings that induce in vivo tissue integration, the full potential of poly(methyl methacrylate) (PMMA) and its derivatives as medical device packaging material has not been explored yet. We therefore elaborated on the development of a universal coating for methacrylate-based materials which ideally should reveal cell-interactivity irrespective of the polymer substrate bulk properties. Within this perspective, the present work reports on the UV-induced synthesis of PMMA and its more flexible poly(ethyleneglycol) (PEG)-based derivative (PMMAPEG) and its subsequent surface decoration using polydopamine (PDA) as well as PDA combined with gelatin B (Gel B). Successful application of both layers was confirmed by multiple surface characterization techniques. The cell interactivity of the materials was studied by performing live-dead assays and immunostainings of the cytoskeletal components of fibroblasts. It can be concluded that only the combination of PDA and Gel B yields materials posessing similar cell interactivities, irrespective of the physicochemical properties of the underlying substrate. The proposed coating outperforms both the PDA functionalized and the pristine polymer surfaces. A universal cell-interactive coating for methacrylate-based medical device packaging materials has thus been realized.
Keywords: A1 Journal article; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation)
DOI: 10.1021/ACS.BIOMAC.5B01094
|
|
“Value in sustainable materials management strategies for open economies case of Flanders (Belgium)”. Christis M, Geerken T, Vercalsteren A, Vrancken KCM, Resources, conservation and recycling 103, 110 (2015). http://doi.org/10.1016/J.RESCONREC.2015.07.014
Abstract: Sustainable Materials Management (SMM) strategies, such as reuse, recycling and energy recovery aim, to capture more of the embedded resource or material value in products and waste streams. Reuse, recycling and energy recovery are existing activities in every society but they are poorly reflected in official statistics. Reaching higher levels of reuse, recycling and energy recovery may provide economic and environmental opportunities (i.e., in terms of GDP, jobs, reduced impacts), but not all options will have a net win-win-win property in practice, as they reduce the need for producing new commodities. In open economies, many primary resources, components and products are imported from abroad, and many goods produced are exported abroad. This paper describes a top-down methodology for estimating the substitution potential of intensifying specific SMM-strategies and material efficiency strategies. We combined both regional and multi-regional EE-IO (environmentally extended input-output) models to link industrial sectors to SMM-strategies. Our method enables us to compare the different SMM and material efficiency strategies in terms of the maximum available budgets for reaching them on a break even basis, maximum savings in global warming emissions and substituted employment effects, both through a regional and global perspective. We add a case on Flanders (Northern region in Belgium) to illustrate the methodology. Flanders is currently developing a policy for SMM. Selecting new regional actions for a Sustainable Materials Management policy can benefit from a good understanding of the international entangled value chains. It is important to understand how much of the chain is within reach of domestic policies and also to assess the consequences in terms of potential winners and losers, regarding GDP, jobs and environmental impacts, both domestically and abroad. We illustrated the potential outcomes for Flanders from four generic SMM-strategies: energy recovery, food waste prevention, recycling and reuse. From a strict regional self-interest perspective, it is preferable to substitute foreign value chains with local economic activities. Reuse creates by far the largest budget for new activities to realize the strategy (31.2% of Flemish GDP compared to 8.3% for food waste prevention, 6.2% for energy recovery and 4.2% for recycling). All four strategies have similar and significant potentials to reduce greenhouse gas emissions. However, food waste prevention and reuse have higher potentials to reduce Flemish territorial GHG-emissions. From a pure Flemish employment perspective, the energy recovery and recycling strategies could replace the fewest Flemish jobs, and from a global perspective, all strategies most likely imply losses of jobs abroad. (C) 2015 Elsevier B.V. All rights reserved.
Keywords: A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1016/J.RESCONREC.2015.07.014
|
|
Amiri-Aref M (2015) Utilization of magnetic nanoparticles and carbon nanotubes to fabrication electrochemical sensors for determination of some important biological and pharmaceutical compounds. 137 p
Keywords: Doctoral thesis; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation)
|
|
“Direct reagentless detection of the affinity binding of recombinant His-tagged firefly luciferase with a nickel-modified gold electrode”. Vagin MY, Trashin SA, Beloglazkina EK, Majouga AG, Mendeleev communications 25, 290 (2015). http://doi.org/10.1016/J.MENCOM.2015.07.021
Abstract: The direct reagentless electrochemical detection of recombinant firefly luciferase binding with a gold electrode modified with nickel complex of 1,16-di[4-(2,6-dihydroxycarbonyl)pyridyl]-1,16-dioxa-8,9-dithiahexadecane has been carried out.
Keywords: A1 Journal article; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation)
DOI: 10.1016/J.MENCOM.2015.07.021
|
|
“Stable Rh particles in hydrotalcite-derived catalysts coated on FeCrAlloy foams by electrosynthesis”. Benito P, Nuyts G, Monti M, de Nolf W, Fornasari G, Janssens K, Scavetta E, Vaccari A, Applied catalysis : B : environmental 179, 321 (2015). http://doi.org/10.1016/J.APCATB.2015.05.035
Abstract: Rh-based structured catalysts for the Catalytic Partial Oxidation of CH4 to syngas were prepared by electrosynthesis of Rh/Mg/Al hydrotalcite-type compounds on FeCrAlloy foams and calcination. The effects of Rh content, total metal concentration, and partial replacement of Mg2+ by Ni2+ in the electrolytic solution on coating thickness, Rh speciation, metallic particle size, and catalytic activity were investigated by SEM/EDS, mu-XRF/XANES and tests under diluted and concentrated reaction conditions. The amount of Rh species, present as Mg (RhxAl1-x)(2)O-4, depended on the thickness of the electrosynthesised layer as well as the Rh particle size and dispersion. Smaller and more dispersed particles were obtained by decreasing the Rh concentration in the electrolytic solution from Rh/Mg/Al=11/70/19 to 5/70/25 and 2/70/28 atomic ratio% (a.r.%) and in thinner rather than thicker layers. Despite the improvement in metallic particles features, the CH4 conversion was negatively affected by the low amount of active sites in the coating, the high metal support interaction and possibly the oxidation of metallic particles and carbon formation. A larger amount of solid containing well dispersed Rh particles was deposited by increasing the total metal concentration from 0.03 M to 0.06 M with the Rh/Mg/Al=5/70/25 a.r.%, and the catalytic performances were enhanced. The partial replacement of Mg2+ by Ni2+ gave rise to a very active bimetallic Rh/Ni catalyst, CH4 conversion and selectivity to syngas were above 90%, however, it slightly deactivated with time-on-stream. (C) 2015 Elsevier B.V. All rights reserved.
Keywords: A1 Journal article; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation)
Impact Factor: 9.446
Times cited: 14
DOI: 10.1016/J.APCATB.2015.05.035
|
|
“Higher sustainability performance of intensive grazing versus zero-grazing dairy systems”. Meul M, Van Passel S, Fremaut D, Haesaert G, Agronomy For Sustainable Development 32, 629 (2012). http://doi.org/10.1007/S13593-011-0074-5
Abstract: Although grazing of dairy cows is an integral part of dairy farming in many European countries, farmers today more often choose for zero-grazing systems, where cows are housed throughout the year. Some studies already compared grazing and zero-grazing systems for specific issues such as labor efficiency, environmental impact, or animal welfare. In our study, we perform a more integrated evaluation, considering relevant ecological, economic, and social aspects. This allows for a balanced and more complete comparison of the sustainability performance of the two production methods. We evaluated ten intensive grazing and ten zero-grazing specialized Flemish dairy farms on the use of nutrients and energy, productivity and profitability, labor input, and animal welfare. In addition, we put special effort in formulating useful management advice for farmers. Therefore, we combined a detailed analysis of the sustainability indicators with an intensive interaction and discussion with farmers and farm advisors. Results show that, on average, the zero-grazing farms performed significantly worse from an ecological and economic point of view. This fact is explained mainly due to a less efficient use of concentrates and byproducts. Social sustainability performance did not differ significantly between the two groups. As a result, the integrated sustainability performance was significantly lower for the zero-grazing group. This finding shows that a further shift from intensive grazing to zero-grazing can move dairy farming in Flanders further away from sustainability. An important advice to improve the ecological and economic performance of zero-grazing farms is to optimize cows' rations to include more forages and optimize forage production and use. More detailed site- and case-specific management advice for farmers of both groups was provided during a discussion meeting. We consider this an essential additional step to any sustainability evaluation, since progress can only be made when monitoring results are translated into practical measures.
Keywords: A1 Journal article; Engineering sciences. Technology; Engineering Management (ENM)
Impact Factor: 4.101
Times cited: 26
DOI: 10.1007/S13593-011-0074-5
|
|
“Determining potential locations for biomass valorization using a macro screening approach”. Van Dael M, Van Passel S, Pelkmans L, Guisson R, Swinnen G, Schreurs E, Biomass &, Bioenergy 45, 175 (2012). http://doi.org/10.1016/J.BIOMBIOE.2012.06.001
Abstract: European policy states that by 2020 at least 20% of final energy consumption should come from renewable energy sources. Biomass as a renewable energy source cannot be disregarded in order to attain this target. In this study a macro screening approach is developed to determine potential locations for biomass valorization in a specified region. The approach consists of five steps: (1) criteria determination, (2) data gathering, (3) weight assignment, (4) final score, (5) spatial representation. The resulting outcome provides a first well balanced scan of the possibilities for energy production using regional biomass. This way policy makers and investors can be supported and motivated to study the possibilities of building energy production plants at specific locations in more detail, which can be described as a 'micro-screening'. In our case study the approach is applied to determine the potentially interesting locations to establish a biomass project. The region has been limited to the forty-four communities in the province of Limburg (Belgium). The macro screening approach has shown to be very effective since the amount of interesting locations has been reduced drastically. (c) 2012 Elsevier Ltd. All rights reserved.
Keywords: A1 Journal article; Engineering sciences. Technology; Engineering Management (ENM)
Impact Factor: 3.219
Times cited: 23
DOI: 10.1016/J.BIOMBIOE.2012.06.001
|
|
“A techno-economic evaluation of a biomass energy conversion park”. Van Dael M, Van Passel S, Pelkmans L, Guisson R, Reumermann P, Luzardo NM, Witters N, Broeze J, Applied Energy 104, 611 (2013). http://doi.org/10.1016/J.APENERGY.2012.11.071
Abstract: Biomass as a renewable energy source has many advantages and is therefore recognized as one of the main renewable energy sources to be deployed in order to attain the target of 20% renewable energy use of final energy consumption by 2020 in Europe. In this paper the concept of a biomass Energy Conversion Park (ECP) is introduced. A biomass ECP can be defined as a synergetic, multi-dimensional biomass conversion site with a highly integrated set of conversion technologies in which a multitude of regionally available biomass (residue) sources are converted into energy and materials. A techno-economic assessment is performed on a case study in the Netherlands to illustrate the concept and to comparatively assess the highly integrated system with two mono-dimensional models. The three evaluated models consist of (1) digestion of the organic fraction of municipal solid waste, (2) co-digestion of manure and co-substrates, and (3) integration. From a socio-economic point of view it can be concluded that it is economically and energetically more interesting to invest in the integrated model than in two separate models. The integration is economically feasible and environmental benefits can be realized. For example, the integrated model allows the implementation of a co-digester. Unmanaged manure would otherwise represent a constant pollution risk. However, from an investor's standpoint one should firstly invest in the municipal solid waste digester since the net present value (NPV) of this mono-dimensional model is higher than that of the multi-dimensional model. A sensitivity analysis is performed to identify the most influencing parameters. Our results are of interest for companies involved in the conversion of biomass. The conclusions are useful for policy makers when deciding on policy instruments concerning manure processing or biogas production. (C) 2012 Elsevier Ltd. All rights reserved.
Keywords: A1 Journal article; Engineering sciences. Technology; Engineering Management (ENM)
Impact Factor: 7.182
Times cited: 45
DOI: 10.1016/J.APENERGY.2012.11.071
|
|
“A patent landscape analysis for organic photovoltaic solar cells : identifying the technology's development phase”. Lizin S, Leroy J, Delvenne C, Dijk M, De Schepper E, Van Passel S, Renewable Energy 57, 5 (2013). http://doi.org/10.1016/J.RENENE.2013.01.027
Abstract: Organic photovoltaics (OPV) have developed into a vast research area. Progress in various directions has made it difficult to monitor the technology's precise development state. We offer a patent landscape analysis over all OPV devices, their substrates and encapsulation materials to provide an overview of patenting activity from a historical, organizational, geographical and technological point of view. Such an exercise is instrumental for private companies and research institutes aiming at both internal or external technology creation. We discuss our findings in the context of the Industrial Life Cycle model and find OPV still residing in the fluid technology development phase. Technology development is still following an exponential growth path, with the majority of patents coming from the Asian continent and in general private companies. For devices, the main technological focus can be traced back to the “H01L-031” international patent classification (IPC) main group. For the queried substrates, the most attention has gone to glass, but paper and textile have drawn significant interest too. Finally, encapsulation is found to be a less mature research field given the smaller number of patent families. The latter shows that the technology has not matured to the level where processing is carried out on a commercial scale. (C) 2013 Elsevier Ltd. All rights reserved.
Keywords: A1 Journal article; Engineering sciences. Technology; Engineering Management (ENM)
Impact Factor: 4.357
Times cited: 18
DOI: 10.1016/J.RENENE.2013.01.027
|
|
“The economics of enhanced landfill mining : private and societal performance drivers”. Van Passel S, Dubois M, Eyckmans J, de Gheldere S, Ang F, Jones PT, Van Acker K, Journal Of Cleaner Production 55, 92 (2013). http://doi.org/10.1016/J.JCLEPRO.2012.03.024
Abstract: This paper addresses the economics of Enhanced Landfill Mining (ELFM) both from a private point of view as well as from a society perspective. The private potential is assessed using a case study for which an investment model is developed to identify the impact of a broad range of parameters on the profitability of ELFM. We found that especially variations in Waste-to-Energy (WtE efficiency, electricity price, CO2-price, WtE investment and operational costs) and ELFM support explain the variation in economic profitability measured by the Internal Rate of Return. To overcome site-specific parameters we also evaluated the regional ELFM potential for the densely populated and industrial region of Flanders (north of Belgium). The total number of potential ELFM sites was estimated using a 5-step procedure and a simulation tool was developed to trade-off private costs and benefits. The analysis shows that there is a substantial economic potential for ELFM projects on the wider regional level. Furthermore, this paper also reviews the costs and benefits from a broader perspective. The carbon footprint of the case study was mapped in order to assess the project's net impact in terms of greenhouse gas emissions. Also the impacts of nature restoration, soil remediation, resource scarcity and reduced import dependence were valued so that they can be used in future social cost-benefit analysis. Given the complex trade-off between economic, social and environmental issues of ELFM projects, we conclude that further refinement of the methodological framework and the development of the integrated decision tools supporting private and public actors, are necessary. (c) 2012 Elsevier Ltd. All rights reserved.
Keywords: A1 Journal article; Engineering sciences. Technology; Engineering Management (ENM)
Impact Factor: 5.715
Times cited: 65
DOI: 10.1016/J.JCLEPRO.2012.03.024
|
|
“Enhanced landfill mining in view of multiple resource recovery : a critical review”. Jones PT, Geysen D, Tielemans Y, Van Passel S, Pontikes Y, Blanpain B, Quaghebeur M, Hoekstra N, Journal Of Cleaner Production 55, 45 (2013). http://doi.org/10.1016/J.JCLEPRO.2012.05.021
Abstract: In a circular economy material loops are closed by recycling of pre-consumer manufacturing scrap/residues, urban mining of End-of-Life products and landfill mining of historic (and future) urban waste streams. However, in the past landfill mining was not performed with a focus on resource recovery. This paper addresses this gap by introducing the concept of Enhanced Landfill Mining, defined as the safe conditioning, excavation and integrated valorization of landfilled waste streams as both materials and energy, using innovative transformation technologies and respecting the most stringent social and ecological criteria. The feasibility of ELFM is studied by synthesizing the research on the Closing the Circle project, the first ELFM project targeting the 18 million metric ton landfill in Houthalen-Helchteren in the East of Belgium. It is argued that Environmental Impact Assessments of ELFM projects should be wide in scope and time. Embedded in a broad resource management perspective, the worldwide potential of ELFM is highlighted, in terms of climate gains, materials and energy utilization, job creation and land reclamation. The potential is quantified for the EU-27 with its 150,000-500,000 landfills. However, for ELFM to reach its full potential, strategic policy decisions and tailored support systems, including combined incentives for material recycling, energy utilization and nature restoration, are required. (c) 2012 Elsevier Ltd. All rights reserved.
Keywords: A1 Journal article; Engineering sciences. Technology; Engineering Management (ENM)
Impact Factor: 5.715
Times cited: 144
DOI: 10.1016/J.JCLEPRO.2012.05.021
|
|
“Techno-economic assessment of pyrolysis char production and application : a review”. Kuppens T, Van Dael M, Vanreppelen K, Carleer R, Yperman J, Schreurs S, Van Passel S, International Conference on BioMass (iconBM 2014), 4-7 May 2014, Florence, Italy / Ranzi, Eliseo [edit.], et al. 37, 67 (2014). http://doi.org/10.3303/CET1437012
Abstract: Many organic residue streams such as pig manure are not or inefficiently used, although they can be converted into valuable materials, as well as energy, using pyrolysis. The yield of the pyrolysis products (i.e. oil, gas and char) is dependent on the process conditions and the feedstock used. Char as a soil amendment or activated carbon are interesting options for valorization of biomass residues. Here, a review is presented of the techno-economic potential of both valorization options based on literature and own experiments with wood from phytoremediation, particle board and waste from beer production. The term “biochar” is specifically used to designate pyrolysis char that is intentionally applied to soil in order to enhance its structure and fertility. Biochar applications are often also motivated by the objective of climate change mitigation. Two main disadvantages for the economic feasibility of biochar applications have been discerned. Firstly, carbon sequestration in agricultural crops and soils is not yet eligible under the Clean Development Mechanism. Secondly, the impact of biochar on crop productivity is unclear. Activated carbon (AC) seems to have interesting adsorption characteristics resulting in potentially high sales prices. A preliminary techno-economic assessment showed that AC production is preferred above oil production for wood from phytoremediation as long as the market price of 2 kEUR.t(-1) for commercially available ACs can be attained. Whenever a feedstock with high nitrogen content is available (e.g. particle board with melamine urea formaldehyde resin), even higher market prices might be attained. This study shows that valorization of the pyrolysis char might be an answer to the slow adoption of pyrolysis in commercial applications. Focus in research and development, for instance in future research with regard to pig manure valorization, should therefore be on sustainable products with high economic value and direct utilization potential.
Keywords: P1 Proceeding; Engineering sciences. Technology
Times cited: 8
DOI: 10.3303/CET1437012
|
|
“Techno-economic assessment of different conversion pathways for pyrolysis char from pig manure”. Kuppens T, Van Dael M, Maggen J, Vanreppelen K, Yperman J, Carleer R, Elen H, Van Passel S, 22nd European Biomass Conference and Exhibition : Setting the Course for a Biobased Economy, 23-26 June 2014, Hamburg, Germany : conference proceedings, 901 (2014)
Abstract: The amount of animal manure that can be brought back to agricultural land is limited by legislation. Because pig manure is available in too large quantities in some areas, we investigate the techno-economic feasibility of converting it into valuable products. First, slurry is separated in water, a thick fraction and a fertilizer concentrate poor in phosphate. Then, the thick fraction is dried and pyrolyzed. Our goal is to identify the optimal pyrolysis and activation conditions for the production of biochar or activated carbon. The latter has interesting adsorption characteristics due to the presence of nitrogen. It can also be used as a soil amendment as it improves biomass quantity and quality. On top, it immobilizes toxic elements and stores carbon in the soil. Char thus has many interesting characteristics and can be valued in different ways. The economic feasibility has been explored by a first techno-economic modelling iteration. The critical factors influencing the feasibility are identified by Monte Carlo simulations for further improvement of the process design.
Keywords: P1 Proceeding; Engineering sciences. Technology
|
|
“Cost-efficient emission abatement of energy and transportation technologies : mitigation costs and policy impacts for Belgium”. De Schepper E, Van Passel S, Lizin S, Achten WMJ, Van Acker K, Clean Technologies And Environmental Policy 16, 1107 (2014). http://doi.org/10.1007/S10098-014-0713-Z
Abstract: In the light of global warming, this paper develops a framework to compare energy and transportation technologies in terms of cost-efficient GHG emission reduction. We conduct a simultaneous assessment of economic and environmental performances through life cycle costing and life cycle assessment. To calculate the GHG mitigation cost, we create reference systems within the base scenario. Further, we extend the concept of the mitigation cost, allowing (i) comparision of technologies given a limited investment resource, and (ii) evaluation of the direct impact of policy measures by means of the subsidized mitigation cost. The framework is illustrated with a case of solar photovoltaics (PV), grid powered battery electric vehicles (BEVs), and solar powered BEVs for a Belgian small and medium sized enterprise. The study's conclusions are that the mitigation cost of solar PV is high, even though this is a mature technology. The emerging mass produced BEVs on the other hand are found to have a large potential for cost-efficient GHG mitigation as indicated by their low cost of mitigation. Finally, based on the subsidized mitigation cost, we conclude that the current financial stimuli for all three investigated technologies are excessive when compared to the CO2 market value under the EU Emission Trading Scheme.
Keywords: A1 Journal article; Economics; Engineering sciences. Technology; Engineering Management (ENM)
Impact Factor: 3.331
Times cited: 14
DOI: 10.1007/S10098-014-0713-Z
|
|
“Bridging the gap between LCA, LCC and CBA as sustainability assessment tools”. Hoogmartens R, Van Passel S, Van Acker K, Dubois M, Environmental Impact Assessment Review 48, 27 (2014). http://doi.org/10.1016/J.EIAR.2014.05.001
Abstract: Increasing interest in sustainability has led to the development of sustainability assessment tools such as Life Cycle Analysis (LCA), Life Cycle Costing (LCC) and Cost-Benefit Analysis (CBA). Due to methodological disparity of these three tools, conflicting assessment results generate confusion for many policy and business decisions. In order to interpret and integrate assessment results, the paper provides a framework that clarifies the connections and coherence between the included assessment methodologies. Building on this framework, the paper further focuses on key aspects to adapt any of the methodologies to full sustainability assessments. Aspects dealt with in the review are for example the reported metrics, the scope, data requirements, discounting, product- or project-related and approaches with respect to scarcity and labor requirements. In addition to these key aspects, the review shows that important connections exist: (i) the three tools can cope with social inequality, (ii) processes such as valuation techniques for LCC and CBA are common, (iii) Environmental Impact Assessment (EIA) is used as input in both LCA and CBA and (iv) LCA can be used in parallel with LCC. Furthermore, the most integrated sustainability approach combines elements of LCA and LCC to achieve the Life Cycle Sustainability Assessment (LCSA). The key aspects and the connections referred to in the review are illustrated with a case study on the treatment of end-of-life automotive glass. (C) 2014 Elsevier Inc. All rights reserved.
Keywords: A1 Journal article; Economics; Engineering Management (ENM)
Impact Factor: 3.094
Times cited: 93
DOI: 10.1016/J.EIAR.2014.05.001
|
|
“Development and techno-economic evaluation of a biorefinery based on biomass (waste) streams : case study in the Netherlands”. Van Dael M, Marquez N, Reumerman P, Pelkmans L, Kuppens T, Van Passel S, Biofuels Bioproducts &, Biorefining-Biofpr 8, 635 (2014). http://doi.org/10.1002/BBB.1460
Abstract: In this paper, the technical and economic advantages of combining conversion technologies into a multi-dimensional plant primarily using regional biomass residues are investigated. The main objective is to show how locally available biomass can be used more efficiently as a source for renewable energy and bio-based products. Therefore, not only is the theoretical perspective considered, but also a reality check for the local situation is taken into account. Although industrial attitude toward biorefineries is positive, the efficient production of a portfolio of bio-based products has not yet been implemented. A biorefinery concept for Moerdijk (the Netherlands) was developed, focusing on grass refining, production of pyrolysis oil, biodiesel production, and bio-LNG production. Grass refining is the most experimental technique of all proposed conversion techniques. In terms of development, pyrolysis oil and bio-LNG production are in the demonstration phase. Anaerobic digestion and biodiesel production are proven techniques. It is shown that this concept allows for synergies with regard to the utilization of residue flows from internal processes. Furthermore, it is demonstrated that by integrating different conversion technologies, an economically feasible concept can be developed in which technologies, currently residing in a demonstration phase, can also be brought to the market. (c) 2013 Society of Chemical Industry and John Wiley & Sons, Ltd
Keywords: A1 Journal article; Engineering sciences. Technology; Engineering Management (ENM)
Impact Factor: 3.694
Times cited: 18
DOI: 10.1002/BBB.1460
|
|
“Potential of life cycle assessment to support environmental decision making at commercial dairy farms”. Meul M, Van Middelaar CE, de Boer IJM, Van Passel S, Fremaut D, Haesaert G, Agricultural Systems 131, 105 (2014). http://doi.org/10.1016/J.AGSY.2014.08.006
Abstract: In this paper, we evaluate the potential of life cycle assessment (LCA) to support environmental decision making at commercial dairy farms. To achieve this, we follow a four-step method that allows converting environmental assessment results using LCA into case-specific advice for farmers. This is illustrated in a case-study involving 20 specialized Flemish dairy farms. Calculated LCA indicators are normalized into scores between 0 and 100, whereby a score of 100 is assumed optimal, to allow for a mutual comparison of indicators for different environmental impact categories. Next, major farm and management characteristics affecting environmental performance are identified using multiple regression and correlation analyses. Finally, comparing specific farm and management characteristics with those of best performing farms identifies farm-specific optimization strategies. We conclude that this approach complies with most of the identified critical success factors for the successful implementation of LCA as a decision support system for farmers. Key aspects herein are (i) the flexibility and accessibility of the model, (ii) the use of readily available farm data, (iii) farm advisors being intended model users, (iv) the identification of key farm and management characteristics affecting environmental performance and (v) the organization of discussion sessions involving farmers and farm advisors. However, attention should be paid (i) to provide sufficient training and guidance for farm advisors on the use of the applied LCA model and the interpretation of results, (ii) to evaluate the correctness of the used data and (iii) to keep the model up-to-date according to new scientific insights and knowledge concerning LCA methodology. (C) 2014 Elsevier Ltd. All rights reserved.
Keywords: A1 Journal article; Engineering Management (ENM)
Impact Factor: 2.571
Times cited: 25
DOI: 10.1016/J.AGSY.2014.08.006
|
|
“Techno-economic assessment of fast pyrolysis for the valorization of short rotation coppice cultivated for phytoextraction”. Kuppens T, Van Dael M, Vanreppelen K, Thewys T, Yperman J, Carleer R, Schreurs S, Van Passel S, Journal Of Cleaner Production 88, 336 (2015). http://doi.org/10.1016/J.JCLEPRO.2014.07.023
Abstract: The main barrier in the commercialization of phytoextraction as a sustainable alternative for remediating metal contaminated soils is its long time period, which can be countered by biomass valorization. From an environmental point of view, fast pyrolysis of the biomass is promising because its lower process temperature prevents metal volatilization. The remaining question is whether fast pyrolysis is also preferred from an economic point of view. Therefore, a techno-economic assessment of fast pyrolysis has been performed for a case study in the Campine region in Belgium. For this region, willow trees cultivated in short rotation have the right characteristics to serve as a phytoextracting crop. A techno-economic assessment requires by definition a multidisciplinary approach. The problem statement urges for a focus on the economic profitability from the viewpoint of an investor, including economic risk analysis. Fast pyrolysis seems more profitable than gasification. The profit is dependent on the scale of operation, the policy support (subsidies) and the oil yield. The economic risk can be reduced by increasing the scale of operation by means of complementing feedstocks, and by valorization of the char byproduct by subsequent processing to activated carbon. (C) 2014 Elsevier Ltd. All rights reserved.
Keywords: A1 Journal article; Engineering Management (ENM)
Impact Factor: 5.715
Times cited: 36
DOI: 10.1016/J.JCLEPRO.2014.07.023
|
|
“Assessment of the sustainability guidelines of EU Renewable Energy Directive : the case of biorefineries”. Maes D, Van Dael M, Vanheusden B, Goovaerts L, Reumerman P, Luzardo NM, Van Passel S, Journal Of Cleaner Production 88, 61 (2015). http://doi.org/10.1016/J.JCLEPRO.2014.04.051
Abstract: Sustainability guidelines can help to safeguard the sustainable use of biological materials. When these guidelines are legally prescribed, their influence on the economic viability of bioenergy, biofuel and bioliquid projects is increased substantially, through their impact on national subsidy regimes and international trade. One of the key examples is the European directive 2009/28/EC, or the Renewable Energy Directive (RED), and the related COM/2010/11 that integrate guidelines for calculating greenhouse gas impact for various bioenergy pathways. This paper looks further into the sustainability results when influenced by principal decisions that are legally open for debate. Therefore, a concise review is conducted of the legal state-of-the-art on whether a product is waste or not. The review pinpoints uncertainty, leading to four potential legal scenarios. The sustainability of a complex biorefinery is analysed for each scenario. The results show (i) a high sensitivity to the principal decisions on the nature of waste materials in the scenarios, and (ii) to the definition of boundaries between the processes. More detailed rules for the application of the RED guidelines are needed, and should be complemented with methods specifically targeting all relevant sustainability aspects, thereby enhancing the overall understanding of the sustainability of the process. (C) 2014 Elsevier Ltd. All rights reserved.
Keywords: A1 Journal article; Economics; Engineering Management (ENM)
Impact Factor: 5.715
Times cited: 25
DOI: 10.1016/J.JCLEPRO.2014.04.051
|
|
“Valorization of thermal treatment residues in enhanced landfill mining : environmental and economic evaluation”. Danthurebandara M, Van Passel S, Machiels L, Van Acker K, Journal Of Cleaner Production 99, 275 (2015). http://doi.org/10.1016/J.JCLEPRO.2015.03.021
Abstract: Enhanced Landfill Mining is an innovative concept which allows the recovery of land, re-introduction of materials to the material cycles and recovery of energy from a considerably large stock of resources held in landfills. Plasma gasification is a viable candidate for combined energy and material valorization in the framework of Enhanced landfill Mining. Besides energy production, plasma gasification also delivers an environmentally stable vitrified residue called plasmastone, which can be converted into building materials. This paper presents an environmental and economic evaluation of the valorization of thermal treatment residues (plasmastone) in the context of Enhanced Landfill Mining. The most common valorization route, that is, the treatment of plasmastone via production of aggregates, is compared with two other possible, higher added value applications, which are inorganic polymer production and blended cement production. The evaluation is based on life cycle assessment and life cycle costing. The study suggests that the environmental and economic performances of the valorization routes depend mainly on the quality and quantity of the final products produced from a certain amount of plasmastone. The materials with the greatest contribution to potential global warming and to the net present value of the valorization scenarios are the process input materials of sodium silicate, sodium hydroxide and cement. The study concludes that the plasmastone valorization via inorganic polymer production yields higher environmental benefits, while the blended cement production provides higher economic profits. Plasmastone valorization via aggregates production does not yield economic or environmental benefits. Given the trade-off between environmental and economic performances, we conclude that the decisions regarding the selection of appropriate valorization routes should be made cautiously to obtain optimal environmental benefits and economic profits. (C) 2015 Elsevier Ltd. All rights reserved.
Keywords: A1 Journal article; Economics; Engineering sciences. Technology; Engineering Management (ENM)
Impact Factor: 5.715
Times cited: 17
DOI: 10.1016/J.JCLEPRO.2015.03.021
|