|
“Impact of calibrated band-tails on the subthreshold swing of pocketed TFETs”. Bizindavyi J, Verhulst AS, Sorée B, Groeseneken G, Conference digest
T2 –, 76th Device Research Conference (DRC), JUN 24-27, 2018, Santa Barbara, CA (2018)
Keywords: P1 Proceeding; Condensed Matter Theory (CMT)
|
|
Winckelmans N (2018) Advanced electron tomography to investigate the growth of homogeneous and heterogeneous nanoparticles. Antwerpen
Keywords: Doctoral thesis; Electron microscopy for materials research (EMAT)
|
|
Claes N (2018) 3D characterization of coated nanoparticles and soft-hard nanocomposites. Antwerpen
Keywords: Doctoral thesis; Electron microscopy for materials research (EMAT)
|
|
“HREM investigation of martensite precursor effects and stacking sequences in Ni-Mn-Ti alloys”. Schryvers D, Lahjouji DE, Slootmaekers B, Potapov PL, Scripta metallurgica et materialia 35, 1235 (1996). http://doi.org/10.1016/1359-6462(96)00271-0
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 3.224
Times cited: 2
DOI: 10.1016/1359-6462(96)00271-0
|
|
“A comparative investigation of replication techniques used for the study of (S+Au) sensitized AgBr microcrystals”. Buschmann V, Schryvers D, van Landuyt J, van Roost C, de Keyzer R, The journal of imaging science and technology 40, 189 (1996)
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 0.349
Times cited: 4
|
|
“Metals and alloys: 2: phase transformations”. Schryvers D, Van Tendeloo G Vch, Weinheim, page 80 (1997).
Keywords: H3 Book chapter; Electron microscopy for materials research (EMAT)
|
|
“Structural characterisation of erbium silicide thin films of an Si(111) substrate”. Frangis N, Van Tendeloo G, van Landuyt J, Muret P, Nguyen TTA, Journal of alloys and compounds 234, 244 (1996). http://doi.org/10.1016/0925-8388(95)02131-0
Abstract: ErSi2-x films (x = 0.1-0.3) grown by co-evaporation at different deposition ratios have been characterised by transmission electron microscopy, electron diffraction and high resolution electron microscopy. A very good epitaxial growth relation with the Si substrate was deduced for a1 samples and observed phases. Different defect modulated structures are formed; they can be described as structural variants (orthorhombic or rhombohedral) of the basic structure. The modulated phases are related to deviations from stoichiometry similar to crystallographic shear structures. The ErSi1.9 material contains Si precipitates, illustrating the preference for the ErSi1.7 composition to be maintained.
Keywords: A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
Impact Factor: 2.999
Times cited: 14
DOI: 10.1016/0925-8388(95)02131-0
|
|
“An electron microscopic study of highly oriented undoped and FeCl3-doped poly (p-phenylenevinylene)”. Zhang XB, Van Tendeloo G, van Landuyt J, van Dyck D, Briers J, Bao Y, Geise HJ, Macromolecules 29, 1554 (1996). http://doi.org/10.1021/ma9513067
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT); Vision lab
Impact Factor: 5.8
Times cited: 10
DOI: 10.1021/ma9513067
|
|
“Observation of vacancy clustering in FZ-Si crystals during in situ electron irradiation in a high voltage electron microscope”. Fedina L, van Landuyt J, Vanhellemont J, Aseev AL, Nuclear instruments and methods in physics research B112, 133 (1996). http://doi.org/10.1016/0168-583X(95)01277-X
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 1.124
Times cited: 4
DOI: 10.1016/0168-583X(95)01277-X
|
|
“Ion beam synthesis of β-SiC at 9500C and structural characterization”. Frangis N, Nejim A, Hemment PLF, Stoemenos J, van Landuyt J, Nuclear instruments and methods in physics research B112, 325 (1996)
Keywords: A3 Journal article; Electron microscopy for materials research (EMAT)
|
|
“The chirality of carbon nanotubules determined by dark-field electron microscopy”. Bernaerts D, op de Beeck M, Amelinckx S, van Landuyt J, Van Tendeloo G, Philosophical magazine: A: physics of condensed matter: defects and mechanical properties 74, 723 (1996). http://doi.org/10.1080/01418619608243538
Abstract: Multishell carbon nanotubules are studied by means of diffraction contrast dark field images. This results in an electron microscopy method for the determination of the sign of the chiral angles in carbon nanotubes. The method is justified by a reasoning either in direct space or in diffraction space. We also investigate a carbon nanotubule exhibiting a bend and we confront the observations with the heptagon-pentagon pair model.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Times cited: 20
DOI: 10.1080/01418619608243538
|
|
“Observation of vacancy clustering in Si crystals during in situ electron irradiation in a high voltage electron microscope”. Fedina L, van Landuyt J, Vanhellemont J, Aseev A, Materials Research Society symposium proceedings 404, 189 (1996)
Keywords: P1 Proceeding; Electron microscopy for materials research (EMAT)
Times cited: 1
|
|
“Electron microscopy characterisation of erbium silicide-thin films grown on a Si(111) substrate”. Frangis N, Van Tendeloo G, van Landuyt J, Muret P, Nguyen TTA, Applied surface science 102, 163 (1996). http://doi.org/10.1016/0169-4332(96)00040-2
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 2.711
Times cited: 9
DOI: 10.1016/0169-4332(96)00040-2
|
|
“High crystalline quality erbium silicide films on (100) silicon grown in high vacuum”. Kaltsas G, Travlos A, Nassiopoulos AG, Frangis N, van Landuyt J, Applied surface science 102, 151 (1996). http://doi.org/10.1016/0169-4332(96)00036-0
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 2.711
Times cited: 14
DOI: 10.1016/0169-4332(96)00036-0
|
|
“New erbium silicide superstructures: a study by high resolution electron microscopy”. Frangis N, Van Tendeloo G, van Landuyt J, Kaltsas G, Travlos A, Nassiopoulos AG, Physica status solidi: A: applied research 158, 107 (1996)
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Times cited: 6
|
|
“Theoretical and experimental investigation of conjugation of 1,6-hexanedithiol on MoS2”. Gul A, Bacaksiz C, Unsal E, Akbali B, Tomak A, Zareie HM, Sahin H, Materials Research Express 5, 036415 (2018). http://doi.org/10.1088/2053-1591/AAB4A6
Abstract: We report an experimental and theoretical investigation of conjugation of 1,6-Hexaneditihiol (HDT) on MoS2 which is prepared by mixing MoS2 structure and HDT molecules in proper solvent. Raman spectra and the calculated phonon bands reveal that the HDT molecules bind covalently to MoS2. Surface morphology of MoS2/HDTstructure is changed upon conjugation ofHDTon MoS2 and characterized by using Scanning Electron Microscope (SEM). Density Functional Theory (DFT) based calculations show that HOMO-LUMO band gap of HDT is altered after the conjugation and two-S binding (handle-like) configuration is energetically most favorable among three different structures. This study displays that the facile thiol functionalization process of MoS2 is promising strategy for obtaining solution processable MoS2.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 1.068
Times cited: 2
DOI: 10.1088/2053-1591/AAB4A6
|
|
“Experimental and computational investigation of graphene/SAMs/n-Si Schottky diodes”. Aydin H, Bacaksiz C, Yagmurcukardes N, Karakaya C, Mermer O, Can M, Senger RT, Sahin H, Selamet Y, Applied Surface Science 428, 1010 (2018). http://doi.org/10.1016/J.APSUSC.2017.09.204
Abstract: We have investigated the effect of two different self-assembled monolayers (SAMs) on electrical characteristics of bilayer graphene (BLG)/n-Si Schottky diodes. Novel 4“bis(diphenylamino)-1, 1':3”-terpheny1-5' carboxylic acids (TPA) and 4,4-di-9H-carbazol-9-y1-1,1':3'1'-terpheny1-5' carboxylic acid (CAR) aromatic SAMs have been used to modify n-Si surfaces. Cyclic voltammetry (CV) and Kelvin probe force microscopy (KPFM) results have been evaluated to verify the modification of n-Si surface. The current-voltage (I-V) characteristics of bare and SAMs modified devices show rectification behaviour verifying a Schottky junction at the interface. The ideality factors (n) from ln(I)-V dependences were determined as 2.13,1.96 and 2.07 for BLG/n-Si, BLG/TPA/n-Si and BLG/CAR/n-Si Schottky diodes, respectively. In addition, Schottky barrier height (SBH) and series resistance (Rs) of SAMs modified diodes were decreased compared to bare diode due to the formation of a compatible interface between graphene and Si as well as n-n interaction between aromatic SAMs and graphene. The CAR-based device exhibits better diode characteristic compared to the TPA-based device. Computational simulations show that the BLG/CAR system exhibits smaller energy-level-differences than the BLG/TPA, which supports the experimental findings of a lower Schottky barrier and series resistance in BLG/CAR diode. (C) 2017 Elsevier B.V. All rights reserved.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 3.387
Times cited: 2
DOI: 10.1016/J.APSUSC.2017.09.204
|
|
“Critical assessment of the process of growth of a YBa2Cu3O7-\delta layer on Y2BaCuO5”. Jacques P, Verbist K, Lapin J, Ryelandt L, Van Tendeloo G, Delannay F, Superconductor science and technology 9, 176 (1996). http://doi.org/10.1088/0953-2048/9/3/008
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 2.325
Times cited: 1
DOI: 10.1088/0953-2048/9/3/008
|
|
“Inclusions in magnetron sputtered YBa2Cu3-x MxO7-d thin films: a study by means of electron microscopy”. Verbist K, Van Tendeloo G, Ye M, Schroeder J, Mehbod M, Deltour R, Microscopy, microanalysis, microstructures 7, 17 (1996). http://doi.org/10.1051/mmm:1996104
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Times cited: 6
DOI: 10.1051/mmm:1996104
|
|
“Structural properties of Zn-substituted epitaxial YBa2Cu3O7-\delta thin films”. Ye M, Schroeder J, Mehbod M, Deltour R, Naessens G, Duvigneaud PH, Verbist K, Van Tendeloo G, Superconductor science and technology 9, 543 (1996). http://doi.org/10.1088/0953-2048/9/7/006
Abstract: We optimized the deposition of YBa2(Cu1-xZnx)(3)O-7-delta thin-films using inverted cylindrical magnetron sputtering and report here a detailed structural study, especially in relation to crystal growth, associated surface morphology, Y2O3 precipitation and other secondary phases important for flux pinning. We find that the epitaxial quality of the Zn-substituted YBa2Cu3O7-delta films is decreased compared with high-quality pure YBa2Cu3O7-delta films prepared under identical conditions. The pure films have smoother surfaces, while those of Zn-substituted films contain pinholes and outgrowths. Secondary phases and a-axis grains were observed in the Zn-substituted films. Y2O3 precipitates with typical dimensions of 50-100 Angstrom have been found in both pure and Zn-substituted samples. However, their density of about 10(23) m(-3), observed in the pure films, is significantly reduced in the Zn-substituted films when increasing the Zn concentration up to 4%.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 2.325
Times cited: 7
DOI: 10.1088/0953-2048/9/7/006
|
|
Korneychuk S (2018) Local study of the band gap and structure of diamond-based nanomaterials by analytical transmission electron microscopy. Antwerpen
Keywords: Doctoral thesis; Electron microscopy for materials research (EMAT)
|
|
“Combination of CeO2 and PtO2 doping for the strong enhancement of Jc under magnetic field in melt-textured superconductor YBaCuO”. Delamare MP, Hervieu M, Wang J, Provost J, Monot I, Verbist K, Van Tendeloo G, Physica: C : superconductivity 262, 220 (1996). http://doi.org/10.1016/0921-4534(96)00225-0
Abstract: A combination of CeO2 and PtO2 doping has been studied in melt-processed YBa2Cu3O7-x. This study was carried out using an optimized well established MTG process. The cerium-platinum doped samples exhibit a high fishtail effect with a J(c) of 4.3 x 10(4) A/cm(2) under an applied field of 1 T. Microstructural and nanostructural studies have been performed. The 211 and BaCeO3 inclusions are a few micrometers wide and the formation of a metastable nanocrystalline phase (Y4Ba4)Cu-8-x(Ce,Pt)(x)O-20+delta related to the perovskite is detected. The 123 grains show no specific extended defect generated by the doping process. The relationship between structure and properties are discussed.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 0.942
Times cited: 27
DOI: 10.1016/0921-4534(96)00225-0
|
|
“Low- or high-angle Ar ion-beam etching to create ramp-type Josephson junctions”. Verbist K, Lebedev OI, Van Tendeloo G, Verhoeven MAJ, Rijnders AJHM, Blank DHA, Superconductor science and technology 9, 978 (1996). http://doi.org/10.1088/0953-2048/9/11/009
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 2.325
Times cited: 10
DOI: 10.1088/0953-2048/9/11/009
|
|
“Structural properties of c-axis oriented epitaxial YBa2Cu3O7-\delta thin films”. Ye M, Schroeder J, Deltour R, Delplancke MP, Winand R, Verbist K, Van Tendeloo G, Superlattices and microstructures 21, 287 (1997)
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 2.123
|
|
“The multiple orientation relationships and morphology of beta phase in Al-Mg-Si-Cu alloy”. Weng Y, Jia Z, Ding L, Muraishi S, Wu X, Liu Q, Journal of alloys and compounds 767, 81 (2018). http://doi.org/10.1016/J.JALLCOM.2018.07.077
Abstract: The orientation relationships (ORs), segregation behavior and morphologies of beta precipitate in an over aged Al-Mg-Si-Cu alloy are systematically characterized by atomic resolution high-angle annular dark field scanning transmission electron microscopy (HAADF-STEM). Six different ORs and two morphologies, i.e. rod-and lath-like are revealed for beta precipitates, and Cu segregation at the (beta/alpha-Al interface is observed in all these precipitates. The rod-like beta precipitate has multiple beta-angles ranging from 6.1 to 14.1 degrees and non-uniform Cu segregation at the (beta/alpha-Al interface, while the lath-like beta precipitate has a constant beta-angle of 0 degrees and a periodic Cu segregation. These different ORs are explained to be attributable to the rotation of QP lattice, a near-hexagonal network of Si columns formed within beta precipitates, which causes different lattice matching of beta with alpha-Al lattice. These findings provide new insights in controlling the precipitation hardening and mechanical properties of this type of alloys. (C) 2018 Elsevier B.V. All rights reserved.
Keywords: A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
Impact Factor: 3.133
Times cited: 4
DOI: 10.1016/J.JALLCOM.2018.07.077
|
|
“Electrical dipole on gapped graphene : bound states and atomic collapse”. Van Pottelberge R, Van Duppen B, Peeters FM, Physical review B 98, 165420 (2018). http://doi.org/10.1103/PHYSREVB.98.165420
Abstract: We investigate the energy spectrum, wave functions, and local density of states of an electrical dipole placed on a sheet of gapped graphene as function of the charge strength Z alpha for different sizes of the dipole and for different regularization parameters. The dipole is modeled as consisting of a positive and negative charge. Bound states are found within the gap region with some energy levels that anticross and others that cross as function of the impurity strength Z alpha. The anticrossings are more pronounced and move to higher charges Z alpha when the length of the dipole decreases. These energy levels turn into atomic collapse states when they enter the positive (or negative) energy continuum. A smooth transition from the single-impurity behavior to the dipole one is observed: The states diving towards the continuum in the single-impurity case are gradually replaced by a series of anticrossings that represent a continuation of the diving states in the single-impurity case. By studying the local density of states at the edge of the dipole we show how the series of anticrossings persist in the positive and negative continuum.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 3.836
Times cited: 8
DOI: 10.1103/PHYSREVB.98.165420
|
|
“Energy filtering in silicon nanowires and nanosheets using a geometric superlattice and its use for steep-slope transistors”. Beckers A, Thewissen M, Sorée B, Journal of applied physics 124, 144304 (2018). http://doi.org/10.1063/1.5043543
Abstract: This paper investigates energy filtering in silicon nanowires and nanosheets by resonant electron tunneling through a geometric superlattice. A geometric superlattice is any kind of periodic geometric feature along the transport direction of the nanowire or nanosheet. Multivalley quantum-transport simulations are used to demonstrate the manifestation of minibands and minibandgaps in the transmission spectra of such a superlattice. We find that the presence of different valleys in the conduction band of silicon favors a nanowire with a rectangular cross section for effective energy filtering. The obtained energy filter can consequently be used in the source extension of a field-effect transistor to prevent high-energy electrons from contributing to the leakage current. Self-consistent Schrodinger-Poisson simulations in the ballistic limit show minimum subthreshold swings of 6 mV/decade for geometric superlattices with indentations. The obtained theoretical performance metrics for the simulated devices are compared with conventional III-V superlatticeFETs and TunnelFETs. The adaptation of the quantum transmitting boundary method to the finite-element simulation of 3-D structures with anisotropic effective mass is presented in Appendixes A and B. Our results bare relevance in the search for steep-slope transistor alternatives which are compatible with the silicon industry and can overcome the power-consumption bottleneck inherent to standard CMOS technologies. Published by AIP Publishing.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 2.068
Times cited: 3
DOI: 10.1063/1.5043543
|
|
“On the control and effect of water content during the electrodeposition of Ni nanostructures from deep eutectic solvents”. Cherigui EAM, Şentosun K, Mamme MH, Lukaczynska M, Terryn H, Bals S, Ustarroz J, The journal of physical chemistry: C : nanomaterials and interfaces 122, 23129 (2018). http://doi.org/10.1021/acs.jpcc.8b05344
Abstract: The electrodeposition of nickel nanostructures on glassy carbon was investigated in 1:2 choline chloride urea deep eutectic solvent (DES) containing different amounts of water. By combining electrochemical techniques, with ex situ field emission scanning electron microscopy, high-angle annular dark field scanning transmission electron microscopy, and energy-dispersive X-ray spectroscopy, the effect of water content on the electrochemical processes occurring during nickel deposition was better understood. At highly negative potentials and depending on water content, Ni growth is halted due to water splitting and formation of a mixed layer of Ni/NiOx(OH)(2(1-x)(ads)). Moreover, under certain conditions, the DES components can also be (electro)chemically reduced at the electrode surface, blocking further three-dimensional growth of the Ni NPs. Hence, a two-dimensional crystalline Ni-containing network can be formed in the interparticle region.
Keywords: A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
Impact Factor: 4.536
Times cited: 27
DOI: 10.1021/acs.jpcc.8b05344
|
|
“Interfacial oxidation and photoluminescence of InP-Based core/shell quantum dots”. Tessier MD, Baquero EA, Dupont D, Grigel V, Bladt E, Bals S, Coppel Y, Hens Z, Nayral C, Delpech F, Chemistry of materials 30, 6877 (2018). http://doi.org/10.1021/ACS.CHEMMATER.8B03117
Abstract: Indium phosphide colloidal quantum dots (QDs) are emerging as an efficient cadmium-free alternative for optoelectronic applications. Recently, syntheses based on easy-to-implement aminophosphine precursors have been developed. We show by solid-state nuclear magnetic resonance spectroscopy that this new approach allows oxide-free indium phosphide core or core/shell quantum dots to be made. Importantly, the oxide-free core/shell interface does not help in achieving higher luminescence efficiencies. We demonstrate that in the case of InP/ZnS and InP/ZnSe QDs, a more pronounced oxidation concurs with a higher photoluminescence efficiency. This study suggests that a II-VI shell on a III-V core generates an interface prone to defects. The most efficient InP/ZnS or InP/ZnSe QDs are therefore made with an oxide buffer layer between the core and the shell: it passivates these interface defects but also results in a somewhat broader emission line width.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 9.466
Times cited: 74
DOI: 10.1021/ACS.CHEMMATER.8B03117
|
|
Bal K (2018) New ways to bridge the gap between microscopic simulations and macroscopic chemistry. Antwerpen
Keywords: Doctoral thesis; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
|