Abstract: Reaction of (2,3,9,10,16,17,23,24-octabutylphthalocyaninato)lanthanide(iii) acetylacetonates ((Bu)PcLn(acac), 1a-c, Ln = Lu (a), Eu (b), La (c)) with a tetrakis(5,7-bis(4-tert-butylphenyl)-6H-1,4-diazepino)[2,3-b,g,l,q]porphyrazine ligand ((tBuPh)DzPzH(2), 2) produced sandwich compounds ((tBuPh)DzPz)Ln(Pc-Bu) (3a-c), which represent the first heteroleptic double-deckers incorporating both Pc and DzPz decks. A combination of high-resolution mass spectrometry, UV-Vis/NIR, MCD, and H-1 NMR spectroscopy, and square-wave voltammetry provided unambiguous characterization of target complexes 3 indicating that their spectral and electrochemical properties are generally intermediate with respect to their homoleptic relatives. Based on the data of solution-state H-1-H-1 NMR (COSY, NOESY) correlation spectroscopy supported by DFT calculations, a dimerization tendency of compounds 3 proportional to the Ln(iii) ion size was found. The spectroelectrochemical study of 3 and the corresponding homoleptic double-deckers revealed a pronounced tendency to aggregation of the one-electron oxidized forms of DzPz-containing double-decker complexes compared to homoleptic Pc(2)Ln compounds.

Abstract: The rate of charge deposition in quartz grains irradiated in natural conditions is computed by radiation transport modeling. Quartz luminescence models are modified with the addition of the resulting charge deposition term, and the influence of this process on the optically stimulated luminescence (OSL) signal is analyzed. The results indicate that the charge deposition occurring in the quartz grain during the time of residence within rock could lead to the depletion of trapped holes in the recombination centres. For the two different quartz models investigated here, complete depletion is expected to occur for rock ages between 500 Ma and 1100 Ma. It is predicted that for sedimentary quartz derived from such rocks, the OSL signal is dominated by the slow component. It was also found that the shape and saturation level of the natural sensitivity-corrected dose response curve (DRC) of quartz is affected by the charge deposition; specifically, a linear reduction of the saturation level with the age of the rock is observed.

Abstract: Fibonacci numbers are a very popular subject in mathematics, culture and science. A major open question is why the ancient Greeks overlooked this series, while they were very familiar with the golden mean and division in extreme and mean ratio. Furthermore, they could compute the square root of five to a high degree of precision using Theon 's ladder. This fact is based on tables built with side and diagonal numbers, and it is a simple and incredibly efficient method to compute roots of integers, though it is little known even now among most of the experts. The biologist D 'Arcy Wentworth Thompson showed that the same method could be used to generate the Fibonacci series using a simple shift in the computation of the tables. He argues, quite convincingly, that the ancient Greeks could not have overlooked this. Actually, the same method can be used to generate all possible regular phyllotaxis patterns.

Abstract: In this paper, two new monolayers, namely PtOS and PtOSe, are theoretically predicted using first-principles calculations. Structural, electronic, optical and thermoelectric properties are explored using full-potential linearized augmented plane-wave (FP-LAPW) method and the semiclassical Boltzmann transport theory. Predicted two-dimensional (2D) materials show good dynamical, thermodynamic and structural stability. Calculated electronic structures indicate the indirect gap semiconductor nature of the PtOS and PtOSe single layers with energy gap of 1.346(2.436) and 0.978(1.978) eV as calculated with the WC(HSE06) functional, respectively. Density of states spectra and valence charge distribution maps suggest a mix of covalent and ionic characters of the chemical bonds. 2D materials at hand exhibit good absorption property in the visible regime with coefficient value reaching the order of 105/cm, even much larger in the ultraviolet, suggesting the promising optoelectronic applicability. Finally, the thermoelectric parameters including electrical conductivity, thermal conductivity, Seebeck coefficient, power factor and figure of merit are determined and analyzed. Results indicate prospective thermoelectric performance of both considered single layers as demonstrated by large figure of merit close to unity. Our work introduces two new 2D multifunctional materials that may possess potential applications in the optoelectronic and thermoelectric nano-devices.

Abstract: Pure hydrogen production via water splitting is an ideal strategy for producing clean and sustainable energy. Two-dimensional (2D) cadmium chalcogenide single-layers with a tetragonal crystal structure, namely Tetra-CdX (X = S, Se, and Te) monolayers, are theoretically predicted by means of density functional theory (DFT). Their structural stability and electronic and optical properties are investigated. We find that Tetra-CdX single-layers are thermodynamically stable. Their stability decreases as we go down the 6A group in the periodic table, i.e., from X = S to Se, and Te which also means that the electronegativity decreases. All considered novel monolayers are indirect band gap semiconductors. Using the HSE06 functional the electronic band gaps of CdS, CdSe, and CdTe monolayers are predicted to be 3.10 eV, 2.97 eV, and 2.90 eV, respectively. The impact of mechanical strain on the physical properties was studied, which indicates that compressive strain increases the band gap and tensile strain decreases the band gap. The optical properties of the Tetra-CdX monolayers show the ability of these monolayers to absorb visible light. Due to the suitable band gaps and band edge positions of Tetra-CdX, these newly discovered 2D materials are promising for photocatalytic water splitting.

Abstract: To gain full control over the growth of carbon nanotubes (CNTs) using plasma-enhanced chemical vapor deposition (PECVD), a thorough understanding of the underlying plasma-catalyst mechanisms is required. Oxygen-containing species are often used as or added to the growth precursor gas, but these species also yield various radicals and ions, which may simultaneously etch the CNT during the growth. At present, the effect of these reactive species on the growth onset has not yet been thoroughly investigated. We here report on the etching mechanism of incipient CNT structures from OH and O radicals as derived from combined (reactive) molecular dynamics (MD) and force-bias Monte Carlo (tfMC) simulations. Our results indicate that the oxygen-containing radicals initiate a dissociation process. In particular, we show how the oxygen species weaken the interaction between the CNT and the nanocluster. As a result of this weakened interaction, the CNT closes off and dissociates from the cluster in the form of a fullerene. Beyond the specific systems studied in this work, these results are generically important in the context of PECVD-based growth of CNTs using oxygen-containing precursors.

Abstract: The low-pressure hollow cathode discharge made of a hollow circular tube and an anode is a type of simple structure discharge system. In particular, under the arc discharge mode, hollow cathodes have high plasma density and energy density with a wide range of adaptability of pressure and current. Low-pressure hollow cathode arc (HCA) discharges have been widely used as plasma sources in various fields such as manufacturing, vacuum welding, and aerospace since the 1960s. Despite the early experimental and applied researches on low-pressure HCA discharges, the basic theoretical study was relatively lagged much behind, resulting in many unanswered questions, such as the optimal discharge operating parameters, the power deposition inside the cathode, the causes of plasma instability, and how to effectively reduce cathode erosion and so on. Due to the special discharge structure of the hollow cathode, it is difficult to make an accurate experimental diagnosis, so a reasonable numerical simulation is an effective study method. However, up to now, there is still a lack of complete and effective numerical models which can evaluate various physical fields in the low-pressure hollow cathode discharges. To address the above problems and difficulties, a comprehensive and self-consistent 2D multi-physical coupling numerical model based on a commercial program of finite element method, the COMSOL Multiphysics, was provided in this paper. The model involves plasma transport, arc flow and heat transfer, and cathode thermal equilibrium, and can consider the effect of an applied magnetic field. The processes of secondary electron emission, thermal-field electron emission, ions and backflow high-energy electrons bombardment, and thermal radiation from the cathode surface are considered in the cathode thermal equilibrium process. Based on the above background, this paper works from the following aspects： In Chapter 1, the basic concepts of low-pressure HCA discharge including the hollow cathode effect, the basic characteristics, and operation modes were introduced firstly; Secondly, the application fields, development history, and overseas and domestic research status of hollow cathode discharge were reviewed; finally, the problems were presented and the research background was explained, and the research purpose of this paper was clarified. In Chapter 2, a complete and self-consistent numerical model of low-pressure hollow cathode discharge was proposed based on the fundamental theory and assumptions, and the set of control equations and boundary conditions in the model were elaborated. In addition, the electron energy distribution function, the collision processes, the solving tools of this model, and calculation schemes were introduced in detail. Finally, a validation example was given to test the rationality and applicability of the numerical model. In Chapter 3, the fundamental plasma properties of low-pressure hollow cathode arcs were investigated. Firstly, the ion Joule heating effect was studied. The results showed that the temperature distributions of the arc and cathode are only able to approach the experimental measurements after considering the ion Joule heating, which shows that the Joule heating of ions is crucial for the heating of the arc plasma. Secondly, by comparing the radial distribution of electron and ion density inside the cathode, the structure of the cathode sheath could be simulated well using this model. Finally, it was shown that the thermal radiation from the cathode surface is an important cooling mechanism of the cathode and only under higher surface emissivity can balance the larger heat flow given by the plasma to the cathode, and the temperature distribution of the cathode shows a non-monotonic increasing trend and is consistent with the profile of experimental measurement so that the so-called active zone is formed. In Chapter 4, the power deposition in the low-pressure HCA was studied in simulation. Two main aspects were considered: the power deposition into particles (both electrons and heavy particles) and the power deposition onto the cathode. It was found that the deposited power into particles increases with the rise of discharge current, but there is no effect on the total power deposition onto the cathode. In high-density plasmas, Coulomb collisions between electrons and ions also become very important, especially since a portion of the deposition energy on heavy particles comes mainly from the energy transfer from electrons to ions. It was also found that regardless of external parameters, half of the power deposition onto the cathode always comes from the particle contribution, while the other half is the net contribution of heat transfer and cathode radiation. The HCA model also allows the simulation of multiple discharge modes for low-pressure HCA discharges over a wide range of gas flow rates. It was also shown that the discharge operating conditions and the external magnetic field can change the distribution of the particle flow on the cathode wall. In Chapter 5, the ion sputtering erosion process on the cathode was simulated by coupling the HCA numerical model with the moving grid technique. The results showed that the ion sputtering erosion on the cathode depends on the ion flux and the plasma potential near the cathode wall and that their distribution and magnitude jointly determine the erosion morphology of the cathode. It was also found that the location of the most severe erosion on the cathode is located in the region of the densest ion flux on the cathode wall, rather than in the longitudinal correspondence with the central region of the internal positive column (IPC). The external magnetic fields can mitigate the cathode erosion and reduce the erosion depth, but stronger magnetic fields lead to a concentration of current density at the cathode tip, which can enhance erosion slightly at the cathode outlet end. Finally, the conclusions and innovation highlights were summarized, and prospects for future work were discussed.

Abstract: Asphalt binder draindown is a potential issue related to stone matrix asphalt (SMA) mixtures. One convenient approach for reducing binder drainage is the use of fibers as stabilizing additives. This study assesses the feasibility of incorporating fibers from banana plants into an SMA mixture as a proposed use for residues from banana cultivation. We found the fiber content capable of preventing draindown and subsequently evaluated the influence of fiber length on the mechanical properties of an SMA mixture. Samples were prepared in a Superpave gyratory compactor with four different fiber lengths (5, 10, 15, and 20 mm) at a fixed content (0.3% by weight) and then compared to samples without fibers. Indirect tensile strength, resilient and dynamic modulus, flow number, and fatigue life tests were conducted. Overall, fibers improved the mechanical properties analyzed. These enhancements were more pronounced for the samples with 15- and 20-mm fibers. Thus, a smaller number of longer fibers was more beneficial to the fiber reinforcement of mixtures than a larger number of shorter fibers.

Abstract: Extensive research has been carried on the molecular adsorption in high surface area materials such as carbonaceous materials and MOFs as well as atomic bonded hydrogen in metals and alloys. Clathrates stand among the ones to be recently suggested for hydrogen storage. Although, the simulations predict lower capacity than the expected by the DOE norms, the additional benefits of clathrates such as low production and operational cost, fully reversible reaction, environmentally benign nature, low risk of flammability make them one of the most promising materials to be explored in the next decade. The inherent ability to tailor the properties of clathrates using techniques such as addition of promoter molecules, use of porous supports and formation of novel reverse micelles morphology provide immense scope customisation and growth. As rapidly evolving materials, clathrates promise to get as close as possible in the search of “holy grail” of hydrogen storage. This review aims to provide the audience with the background of the current developments in the solid-state hydrogen storage materials, with a special focus on the hydrogen clathrates. The in-depth analysis of the hydrogen clathrates will be provided beginning from their discovery, various additives utilised to enhance their thermodynamic and kinetic properties, challenges in the characterisation of hydrogen in clathrates, theoretical developments to justify the experimental findings and the upscaling opportunities presented by this system. The review will present state of the art in the field and also provide a global picture for the path forward.

Abstract: Landfill mining (LFM) refers to the excavation and processing of formerly buried waste streams. It offers significant environmental and societal benefits through the mitigation of greenhouse gas emissions or the reduction of long-term waste management costs. LFM’s profitability, however, is still in question and public investment support might be necessary to fully exploit its potential. To enable decision-makers to identify the best solutions for a landfill site, societal impacts of LFM still have to be investigated. Throughout relevant literature, societal impacts of LFM projects have only selectively been studied and it remains unclear if and which benefits justify policy interventions. This paper firstly provides a comprehensive conceptualization of the societal impact of an LFM project and dives into the underlying societal context of this emerging industry. It disentangles formerly identified burdens and benefits by applying a system dynamics approach to LFM research. Based on this approach, four causal loop diagrams are presented showing how LFM is embedded into its societal context, analyzing the composition of the net societal impact of an LFM project, the mechanisms influencing LFM’s public acceptance, and the dynamics of the market acceptance of LFM products. Key variables and leverage points have been identified, such as (i) technology choices influencing avoided impacts from the mitigations of primary resource consumption, since many societal impacts are closely related to environmental impacts, (ii) a timely and broad stakeholder involvement to prevent project opposition, and (iii) the after-use of the mined landfill, generating a major part of the local and regional societal benefits but also creating potential conflicts between stakeholder interests. Key intradimensional trade-offs and potential conflicts were identified in (i) spatial and (ii) temporal risk distribution, (iii) conflicting societal goals of the after-use such as job creations and recreation, as well as (iv) material and energy recuperation. These findings provide important insights for LFM decision-makers and can help to implement this emerging industry in a sustainable way.

Abstract: The impregnation of size-controlled gold nanoparticles (AuNPs) on an anatase TiO2 structure (AuNPs@TiO2) was studied for the photoelectrochemical detection of hydroquinone (HQ) under visible light illumination integrated into a flow injection analysis (FIA) setup. The crystalline form of TiO2 was preserved during synthesis and the homogeneous distribution of AuNPs over the TiO2 structure was confirmed. Its photoelectrocatalytic activity was improved due to the presence of AuNPs, preventing charge recombination in TiO2 and improving its light absorption ability by the surface plasmon resonance effect (SPR). The FIA system was used in order to significantly reduce the electrode fouling during electroanalysis through periodic washing steps of the electrode surface. During the amperometric detection process, reactive oxygen species (ROS), generated by visible light illumination of AuNPs@TiO2, participate in the oxidation process of HQ. The reduction of the oxidized form of HQ, i.e. benzoquinone (BQ) occurs by applying a negative potential and the measurable amperometric response will be proportional to the initial HQ concentration. The influencing parameters on the response of the amperometric photocurrent such as applied potential, flow rate and pH were investigated. The linear correlation between the amperometric response and the concentration of HQ was recorded (range 0.0125 – 1.0 µM) with a limit of detection (LOD) of 33.8 nM and sensitivity of 0.22 A M−1 cm−2. In this study, we illustrated for the first time that the impregnation of AuNPs in TiO2 allows the sensitive detection of phenolic substances under green laser illumination by using a photoelectrochemical flow system.

Abstract: Environmental effects and natural resources depletion associated with agriculture production affect the agriculture response to climate change. Traditional cross-sectional climate response models ignore this requirement. This research estimates the impact of climate on European agriculture using a continental scale Ricardian analysis. We correct farm income by accounting for resources (energy, fertilisers, pesticides, and water) use intensity and calculate the sustainable value for a sample of 9497 specialized field crop farms. Compared with the traditional Ricardian method, the marginal effects of temperature remain positive (but less positive) in Northern countries, while it leads to less damages in Southern countries when net revenue and farms? sustainable values are used as dependent variables. Accounting for the environmental effects and depletion of natural capital improves the ability of the Ricardian method to estimate agriculture climate response functions in the long run.

Abstract: At the core of the theoretical framework of the ferroelectric field-effect transistor (FeFET) is the thermodynamic principle that one can determine the equilibrium behavior of ferroelectric (FERRO) systems using the appropriate thermodynamic potential. In literature, it is often implicitly assumed, without formal justification, that the Gibbs free energy is the appropriate potential and that the impact of free charge accumulation can be neglected. In this Article, we first formally demonstrate that the Grand Potential is the appropriate thermodynamic potential to analyze the equilibrium behavior of perfectly coherent and uniform FERRO-systems. We demonstrate that the Grand Potential only reduces to the Gibbs free energy for perfectly non-conductive FERRO-systems. Consequently, the Grand Potential is always required for free charge-conducting FERRO-systems. We demonstrate that free charge accumulation at the FERRO interface increases the hysteretic device characteristics. Lastly, a theoretical best-case upper limit for the interface defect density D-FI is identified. The ferroelectric field-effect transistor, which has attracted much attention for application as both a highly energy-efficient logic device and a non-volatile memory device, has often been studied within the framework of equilibrium thermodynamics. Here, the authors theoretically demonstrate the importance of utilizing the correct thermodynamic potential and investigate the impact of free charge accumulation on the equilibrium performance of ferroelectric-based systems.

Abstract: The number of agricultural cooperatives increased quickly in Ethiopia since the 1990s. While many papers studied the impact of membership of Ethiopian cooperatives, not much is known on their performance. This study takes a cooperative-level perspective which is unique in an African context. It compares the economic performance proxied by sales revenue and profit of a wide range of agricultural cooperatives in northern Ethiopia. Data were collected from 511 agricultural cooperatives in 12 districts of Tigray. The contributing factors of the performance are analyzed with Ordinary Least Squares regression (OLS) and Heckman selection models. Our results underscore the importance of membership size, total assets, presence of conflict among members, and union membership. Chairperson characteristics and the internal organization of a cooperative seem to be less correlated to performance.