“Can we control the thickness of ultrathin silica layers by hyperthermal silicon oxidation at room temperature?”.Khalilov U, Neyts EC, Pourtois G, van Duin ACT, The journal of physical chemistry: C : nanomaterials and interfaces 115, 24839 (2011). http://doi.org/10.1021/jp2082566
Abstract: Using reactive molecular dynamics simulations by means of the ReaxFF potential, we studied the growth mechanism of ultrathin silica (SiO2) layers during hyperthermal oxidation at room temperature. Oxidation of Si(100){2 × 1} surfaces by both atomic and molecular oxygen was investigated in the energy range 15 eV. The oxidation mechanism, which differs from thermal oxidation, is discussed. In the case of oxidation by molecular O2, silica is quickly formed and the thickness of the formed layers remains limited compared to oxidation by atomic oxygen. The Si/SiO2 interfaces are analyzed in terms of partial charges and angle distributions. The obtained structures of the ultrathin SiO2 films are amorphous, including some intrinsic defects. This study is important for the fabrication of silica-based devices in the micro- and nanoelectronics industry, and more specifically for the fabrication of metal oxide semiconductor devices.
Keywords: A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Impact Factor: 4.536
Times cited: 36
DOI: 10.1021/jp2082566
|
“Scheme for the generation of entangled atomic state in cavity QED”. Duan ZL, Chen ZY, Zhang JT, Feng XL, Xu ZZ, European physical journal : D : atomic, molecular and optical physics 30, 275 (2004). http://doi.org/10.1140/epjd/e2004-00086-2
Abstract: We propose a scheme to generate the entangled state of two Lambda-type three-level atoms trapped in a cavity. The atoms are initially prepared in their excited state and the cavity in vacuum state. Each atom has two possibilities to deexcite to one of the ground states. If two different polarized photons are detected subsequently, it is sure that both atoms are in different ground states. But which atom is in which ground state cannot be determined, the atoms are thus prepared in a superposition of two ground states, i.e., an entangled state. In comparison with the proposal of Hong and Lee [Phys. Rev. Lett. 89, 237901 (2002)], the requirement of a single polarized photon source can be avoided in our scheme.
Keywords: A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Impact Factor: 1.288
Times cited: 4
DOI: 10.1140/epjd/e2004-00086-2
|
“The mode-deviation effect of trapped spinor bose gas beyond mean field theory”. Xu Y, Jia D-J, Chen Z, Gao Y, Li F-S, International journal of modern physics: B: condensed matter physics, statistical physics, applied physics 18, 1339 (2004). http://doi.org/10.1142/S0217979204024719
Abstract: The deviation effect of spinor mode from the single-mode for a spin-1 Bose gas of trapped atoms is studied beyond the mean field theory. Based on the effective Hamiltonian with nondegenerated level of the collective spin states, the splitting level of the system energy due to the deviation effect has been calculated. For the large condensates of (87)Rb and (23)Na with atom number N > 10(5), the splitting fraction of the energy, arising from the magnetization exhibited by the trapped Bose gas, is found to have a typical order of (10(-4) similar to 10(-8)), decreasing as N(-2) for (87)Rb and increasing as -N(-2) for 23 Na, respectively.
Keywords: A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Impact Factor: 0.736
Times cited: 1
DOI: 10.1142/S0217979204024719
|
“Optical bistability and multistability in four-level systems”. Chen Z, Feng X, Xu Y, Yu MY, Physica scripta 68, 199 (2003). http://doi.org/10.1238/Physica.Regular.068a00199
Abstract: The optical behavior of a four-level system in a ring cavity driven by two coherent laser fields is studied. One laser field is treated as the incident field and the other the control field, respectively. It is found that there is optical transparency when the difference between the two frequency detunings of the incident and control fields from the corresponding atomic transition frequencies is zero. Optical bistability can be produced and controlled by increasing the magnitude of the frequency difference. The bistable hysteresis becomes larger when the frequency difference is increased. Further increase of the latter can lead to onset of multistability.
Keywords: A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Impact Factor: 1.28
Times cited: 8
DOI: 10.1238/Physica.Regular.068a00199
|
“Highly dispersed mixed zirconia and hafnia nanoparticles in a silica matrix: First example of a ZrO2-HfO2-SiO2 ternary oxide system”. Armelao L, Bertagnolli H, Bleiner D, Groenewolt M, Gross S, Krishnan V, Sada C, Schubert U, Tondello E, Zattin A, Advanced functional materials (2007). http://doi.org/10.1002/ADFM.200600458
Abstract: ZrO2 and HfO2 nanoparticles are homogeneously dispersed in SiO2 matrices (supported film and bulk powders) by copolymerization of two oxozirconium and oxohafnium clusters (M4O(2)(OMc)(12), M= Zr, Hf; OMc = OC(O)-C(CH3)=CH2) with (methacryloxypropyl)trimethoxysilane (MAPTMS, (CH2=C(CH3)C(O)O)-(CH2)(3)Si(OCH3)(3)). After calcination (at a temperature >= 800 degrees C), a silica matrix with homogeneously distributed MO2 nanocrystallites is obtained. This route yields a spatially homogeneous dispersion of the metal precursors inside the silica matrix, which is maintained during calcination. The composition of the films and the powders is studied before and after calcination by using Fourier transform infrared (FTIR) analysis, X-ray photoelectron spectroscopy (XPS), secondary ion mass spectrometry (SIMS), and laser ablation inductively coupled plasma mass spectrometry (LA-ICPMS). The local environment of the metal atoms in one of the calcined samples is investigated by using X-ray Absorption Fine Structure (XAFS) spectroscopy. Through X-ray diffraction (XRD) the crystallization of Hf and Zr oxides is seen at temperatures higher than those expected for the pure oxides, and transmission electron microscopy (TEM) shows the presence of well-distributed and isolated crystalline oxide nanoparticles (540 nm).
Keywords: A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Impact Factor: 12.124
Times cited: 34
DOI: 10.1002/ADFM.200600458
|
“FIB, TEM and LA-ICPMS investigations on melt inclusions in Martian meteorites –, Analytical capabilities and geochemical insights”. Bleiner D, Macri M, Gasser P, Sautter V, Maras A, Talanta : the international journal of pure and applied analytical chemistry (2006). http://doi.org/10.1016/J.TALANTA.2005.08.022
Abstract: In order to obtain full information coverage on melt inclusions in Martian meteorites (subgroup nakhlites) complementary micro-analytical techniques were used, i.e. focused ion beam, transmission electron microscopy and laser ablation. Using focused ion beam several lamellae for transmission electron microscopy were prepared and secondary electron images of cross-sections could be acquired. Laser ablation-inductively coupled plasma mass spectrometry analyses were performed on selected inclusions to obtain mass-oriented bulk composition of inclusions at depth. The differences in composition between melt inclusions in olivine and augite crystals would suggest a xenocrystic origin for olivine. Furthermore, electron diffraction patterns clearly indicated that the SiO2-rich phase in inclusions from augite in meteorites from Northwest Africa site is re-crystallized, whereas it is still vitreous in the inclusions from Nakhla sampling site. Therefore, different post-entrapment evolutions were active for the two nakhlite meteorite sets, the Nakhla and the NWA817 set. Melt inclusions in Nakhla olivine presented alteration veins, which were presumably produced before their landing on Earth. If this is the case, this would indicate a alteration stage already on Mars with all the consequence in terms of climate history. Melt inclusions in Nakhla augite resulted unaffected by any alteration or modification following the entrapment, and therefore represent the best candidate to indicate the pristine magma composition. (c) 2005 Elsevier B.V. All rights reserved.
Keywords: A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Impact Factor: 4.162
Times cited: 9
DOI: 10.1016/J.TALANTA.2005.08.022
|
“First-principle calculations on gate/dielectric interfaces : on the origin of work function shifts”. Pourtois G, Lauwers A, Kittl J, Pantisano L, Sorée B, De Gendt S, Magnus W, Heyns A, Maex K, Microelectronic engineering 80, 272 (2005). http://doi.org/10.1016/j.mee.2005.04.080
Abstract: The impact of interfacial chemistry occurring at dielectric/gate interface of P-MOS and N-MOS devices is reviewed through a quick literature survey. A specific emphasis is put on the way the bond polarization that occurs between a dielectric and a metal substrate impacts on the gate work function. First-principle simulations are then used to study the work function changes induced by dopant aggregation in nickel monosilicide metal gates. It is shown that the changes are a natural consequence of the variation of the interface polarization.
Keywords: A1 Journal article; Engineering sciences. Technology; Condensed Matter Theory (CMT); Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Impact Factor: 1.806
Times cited: 31
DOI: 10.1016/j.mee.2005.04.080
|
“Molecular dynamics simulation of dust clusters in plasmas”. Chen Z, Yu MY, Luo H, Physica scripta 71, 638 (2005). http://doi.org/10.1088/0031-8949/71/6/010
Abstract: Finite and infinite three-dimensional dust systems and their configurational and transport properties are investigated by Molecular Dynamics simulation. The model dust-dust interaction potential includes an attraction part. Spherical dust clusters or balls are found and their structural and transport properties studied. Qualitatively, the cluster structure agrees well with recent experimental results.
Keywords: A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Impact Factor: 1.28
Times cited: 13
DOI: 10.1088/0031-8949/71/6/010
|
“Effect of high-frequency electromagnetic field on Te+-implanted (001) Si</tex>”. Kalitzova M, Vlakhov E, Marinov Y, Gesheva K, Ignatova VA, Lebedev O, Muntele C, Gijbels R, Vacuum: the international journal and abstracting service for vacuum science and technology 76, 325 (2004). http://doi.org/10.1016/j.vacuum.2004.07.055
Abstract: The analysis of high-frequency electromagnetic field (HFEMF) effects on the microstructure and electrical properties of Te+ implanted (0 0 1) Si is reported. Cross-sectional high-resolution transmission electron microscopy (XHRTEM) demonstrates the formation of Te nanoclusters (NCs) embedded in the Si layer amorphized by implantation (a-Si) at fluences greater than or equal to 1 x 10(16) cm(-2). Post-implantation treatment with 0.45 MHz HFEMF leads to enlargement of Te NCs, their diffusion and accumulation at the a-Si surface and formation of laterally connected extended tellurium structures above the percolation threshold, appearing at an ion fluence of 1 x 10(17) cm(-2). AC electrical conductivity measurements show nearly four orders of magnitude decrease of impedance resistivity in this case, which is in good agreement with the results of our structural studies. The results obtained are discussed in terms of the two-phase isotropic spinodal structure. (C) 2004 Elsevier Ltd. All rights reserved.
Keywords: A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Impact Factor: 1.53
Times cited: 2
DOI: 10.1016/j.vacuum.2004.07.055
|
“Long-distance channeling and focusing of lasers in plasmas”. Yuan X, Yu W, Yu MY, Chen ZY, Liu JR, Lu PX, Li RX, Qian LJ, Lu BD, Physica scripta 66, 381 (2002). http://doi.org/10.1238/Physica.Regular.066a00381
Abstract: The propagation of a short laser beam in plasma is investigated analytically Relativistic ponderomotive force and space charge effects are included, and an equation describing the evolution of the laser spot size is derived. It is shown that self-consistent electron cavitation can lead to self channelling and thus long-distance self-focusing of the laser. The condition for the latter to occur is given.
Keywords: A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Impact Factor: 1.28
Times cited: 2
DOI: 10.1238/Physica.Regular.066a00381
|
“Laser microprobe mass spectrometry in biology and biomedicine”. Eeckhaoudt S, van Vaeck L, Gijbels R, van Grieken RE, Scanning microscopy S8, 335 (1994)
Keywords: A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT); AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation)
|
“The anharmonic-force field of thioformaldehyde, h2cs, by ab-initio methods”. Martin JML, Francois, Gijbels R, Journal of molecular spectroscopy 168, 363 (1994). http://doi.org/10.1006/jmsp.1994.1285
Abstract: The quartic force field of thioformaldehyde has been calculated ab initio using large basis sets and augmented coupled cluster methods. Calculated fundamentals are in excellent agreement with experiment, as is the most important Coriolis coupling constant. Computed values for the anharmonicity, rovibrational coupling, and centrifugal distortion constants of the four isotopomers (H2CS)-S-32, (H2CS)-S-34, (HDCS)-S-32, and (D2CS)-S-32 have been reported. Predictions have been made for all vibrational transitions from the ground state to excited states with at most two quanta for these isotopomers, both using second-order perturbation theory corrected for Darling-Dennison resonance and using vibrational SCF-CI calculations. For (D2CS)-S-32, perturbation theory performs quite well; for the other isotopomers, performance is poorer for states involving excitation of the out-of-plane bend and, for the (H2CS)-S-32 and (H2CS)-S-34 isotopomers, also for the antisymmetric bend that is in severe Coriolis resonance with it. A possible explanation has been suggested. (C) 1994 Academic Press, Inc.
Keywords: A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Impact Factor: 1.482
Times cited: 18
DOI: 10.1006/jmsp.1994.1285
|
“Molecular dynamics simulation of temperature effects on CF(3)(+) etching of Si surface”. Jian-Ping N, Xiao-Dan L, Cheng-Li Z, You-Min Q, Ping-Ni H, Bogaerts A, Fu-Jun G, Wuli xuebao 59, 7225 (2010)
Abstract: Molecular dynamics method was employed to investigate the effects of the reaction layer formed near the surface region on CF(3)(+) etching of Si at different temperatures. The simulation results show that the coverages of F and C are sensitive to the surface temperature. With increasing temperature, the physical etching is enhanced, while the chemical etching is weakened. It is found that with increasing surface temperature, the etching rate of Si increases. As to the etching products, the yields of SiF and SiF(2) increase with temperature, whereas the yield of SiF(3) is not sensitive to the surface temperature. And the increase of the etching yield is mainly due to the increased desorption of SiF and SiF(2). The comparison shows that the reactive layer plays an important part in the subsequeat impacting, which enhances the etching rate of Si and weakens the chemical etching intensity.
Keywords: A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Impact Factor: 0.624
|
“Modeling of a dielectric barrier discharge used as a flowing chemical reactor”. Petrovic D, Martens T, van Dijk J, Brok WJM, Bogaerts A, , 262 (2008)
Keywords: P1 Proceeding; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
|
“Sputtering of Si(001) and SiC(001) by grazing ion bombardment”. Elmonov AA, Yusupov MS, Dzhurakhalov AA, Bogaerts A, , 209 (2008)
Abstract: The peculiarities of sputtering processes at 0.5-5 keV Ne grazing ion bombardment of Si(001) and SiC(001) surfaces and their possible application for the surface modification have been studied by computer simulation. Sputtering yields in the primary knock-on recoil atoms regime versus the initial energy of incident ions (E(0) = 0.5-5 keV) and angle of incidence (psi = 0-30 degrees) counted from a target surface have been calculated. Comparative studies of layer-by-layer sputtering for Si(001) and SiC(001) surfaces versus the initial energy of incident ions as well as an effective sputtering and sputtering threshold are discussed.
Keywords: P1 Proceeding; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
|
“The influence of the secondary electron emission coefficient and effect of the gas heating on the calculated electrical characteristics of a grimm type glow discharge cell”. Derzsi A, Donko Z, Bogaerts A, Hoffmann V, , 285 (2008)
Abstract: Electron emission properties of cathode surfaces affect considerably the electrical characteristics of glow discharges. Using a heavy-particle hybrid model ill 2 dimensions, we investigate the influence of the secondary electron emission coefficient gamma oil the calculated discharge characteristics for both 'clean' and 'dirty' cathode surface conditions, and assuming a constant gamma parameter as well. The effect of the gas heating and the role of the heavy particles reflected from the cathode on this process is also studied.
Keywords: P1 Proceeding; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
|
“Functioning of thiocyanate ions during sulphur and sulphur-plus-gold Sensitization”. Charlier E, Gijbels R, Van Doorselaer M, De Keyzer R, , 172 (2000)
Abstract: Not much about the effect of thiocyanate addition on the sulphur ripening is known, although it is used for many applications in photographic practice. Via a combination of tracer analysis and diffuse reflectance spectroscopy the effect of thiocyanate addition on the sulphur and sulphur-plus-gold ripening could be unveiled. When thiocyanate is added prior to the sulphur addition, it appears to rearrange the silver halide surface in such way that the sulphur deposition rate is enhanced, but the supply of interstitials is limited. Addition of thiocyanate after the sulphur reaction results in the formation of thiocyanate complexes with silver, from which a silver ion is more easily deposited in a surface cell of the silver sulphide clusters thus enhancing the sensitization rate. For sulphur-plus-gold sensitized emulsions it was observed that part of the gold ions could be removed out of the Ag2-xAuxS clusters by addition of thiocyanate ions and subsequent washing. Hence, it was concluded that two different types of gold ions are present in the silver sulphide clusters; 1. gold ions which are substitutional for silver (bound between sulphur and bromide ions) 2. gold ions which bridge two or three sulphur atoms. Incorporation of gold ions into silver sulphide clusters suppresses their optical absorption in diffuse reflectance spectroscopy. Since the optical absorption at 505 nm can completely be restored by addition of thiocyanate, it is assumed that the entity absorbing at this wavelength is a monomer of silver sulphide.
Keywords: P1 Proceeding; Engineering sciences. Technology; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
|
“The exchange of fluorinated dyes between different types of silver halide microcrystals studied by time of flight secondary ion mass spectrometry (TOF-SIMS)”. Lenaerts J, Verlinden G, Gijbels R, Geuens I, Callant P, , 180 (2000)
Keywords: P1 Proceeding; Engineering sciences. Technology; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
|
“Micro and surface analysis of individual silver halide microcrystals using a scanning ion microprobe”. Geuens I, Gijbels R, Dekeyzer R, Verbeeck A, Papers , 27 (1994)
Keywords: P1 Proceeding; Engineering sciences. Technology; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
|
“Reaction mechanisms for atomic layer deposition of aluminum oxide on semiconductor substrates”. Delabie A, Sioncke S, Rip J, Van Elshocht S, Pourtois G, Mueller M, Beckhoff B, Pierloot K, Journal of vacuum science and technology: A: vacuum surfaces and films 30, 01a127 (2012). http://doi.org/10.1116/1.3664090
Abstract: In this work, we have studied the TMA/H(2)O (TMA Al(CH(3))(3)) atomic layer deposition (ALD) of Al(2)O(3) on hydroxyl (OH) and thiol (SH) terminated semiconductor substrates. Total reflection x-ray fluorescence reveals a complex growth-per-cycle evolution during the early ALD reaction cycles. OH and SH terminated surfaces demonstrate growth inhibition from the second reaction cycle on. Theoretical calculations, based on density functional theory, are performed on cluster models to investigate the first TMA/H(2)O reaction cycle. Based on the theoretical results, we discuss possible mechanisms for the growth inhibition from the second reaction cycle on. In addition, our calculations show that AlCH(3) groups are hydrolyzed by a H(2)O molecule adsorbed on a neighboring Al atom, independent of the type of backbonds (Si-O, Ge-O, or Ge-S) of AlCH(3). The coordination of Al remains four-fold after the first TMA/H(2)O reaction cycle. (C) 2012 American Vacuum Society. [DOI: 10.1116/1.3664090]
Keywords: A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Impact Factor: 1.374
Times cited: 41
DOI: 10.1116/1.3664090
|
“Strain-induced semiconductor to metal transition in the two-dimensional honeycomb structure of MoS2”. Scalise E, Houssa M, Pourtois G, Afanas'ev V, Stesmans A, Nano Research 5, 43 (2012). http://doi.org/10.1007/s12274-011-0183-0
Abstract: The electronic properties of two-dimensional honeycomb structures of molybdenum disulfide (MoS(2)) subjected to biaxial strain have been investigated using first-principles calculations based on density functional theory. On applying compressive or tensile bi-axial strain on bi-layer and mono-layer MoS(2), the electronic properties are predicted to change from semiconducting to metallic. These changes present very interesting possibilities for engineering the electronic properties of two-dimensional structures of MoS(2).
Keywords: A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Impact Factor: 7.354
Times cited: 407
DOI: 10.1007/s12274-011-0183-0
|
“The effect of F2 attachment by low-energy electrons on the electron behaviour in an Ar/CF4 inductively coupled plasma”. Zhao S-X, Gao F, Wang Y-N, Bogaerts A, Plasma sources science and technology 21, 025008 (2012). http://doi.org/10.1088/0963-0252/21/2/025008
Abstract: The electron behaviour in an Ar/CF4 inductively coupled plasma is investigated by a Langmuir probe and a hybrid model. The simulated and measured results include electron density, temperature and electron energy distribution function for different values of Ar/CF4 ratio, coil power and gas pressure. The hybrid plasma equipment model simulations show qualitative agreement with experiment. The effect of F2 electron attachment on the electron behaviour is explored by comparing two sets of data based on different F atom boundary conditions. It is demonstrated that electron attachment at F2 molecules is responsible for the depletion of low-energy electrons, causing a density decrease as well as a temperature increase when CF4 is added to an Ar plasma.
Keywords: A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Impact Factor: 3.302
Times cited: 23
DOI: 10.1088/0963-0252/21/2/025008
|
“Uniform-acceptance force-bias Monte Carlo method with time scale to study solid-state diffusion”. Mees MJ, Pourtois G, Neyts EC, Thijsse BJ, Stesmans A, Physical review : B : condensed matter and materials physics 85, 134301 (2012). http://doi.org/10.1103/PhysRevB.85.134301
Abstract: Monte Carlo (MC) methods have a long-standing history as partners of molecular dynamics (MD) to simulate the evolution of materials at the atomic scale. Among these techniques, the uniform-acceptance force-bias Monte Carlo (UFMC) method [ G. Dereli Mol. Simul. 8 351 (1992)] has recently attracted attention [ M. Timonova et al. Phys. Rev. B 81 144107 (2010)] thanks to its apparent capacity of being able to simulate physical processes in a reduced number of iterations compared to classical MD methods. The origin of this efficiency remains, however, unclear. In this work we derive a UFMC method starting from basic thermodynamic principles, which leads to an intuitive and unambiguous formalism. The approach includes a statistically relevant time step per Monte Carlo iteration, showing a significant speed-up compared to MD simulations. This time-stamped force-bias Monte Carlo (tfMC) formalism is tested on both simple one-dimensional and three-dimensional systems. Both test-cases give excellent results in agreement with analytical solutions and literature reports. The inclusion of a time scale, the simplicity of the method, and the enhancement of the time step compared to classical MD methods make this method very appealing for studying the dynamics of many-particle systems.
Keywords: A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Impact Factor: 3.836
Times cited: 31
DOI: 10.1103/PhysRevB.85.134301
|
“Insights in the plasma-assisted growth of carbon nanotubes through atomic scale simulations : effect of electric field”. Neyts EC, van Duin ACT, Bogaerts A, Journal of the American Chemical Society 134, 1256 (2012). http://doi.org/10.1021/ja2096317
Abstract: Carbon nanotubes (CNTs) are nowadays routinely grown in a thermal CVD setup. State-of-the-art plasma-enhanced CVD (PECVD) growth, however, offers advantages over thermal CVD. A lower growth temperature and the growth of aligned freestanding single-walled CNTs (SWNTs) makes the technique very attractive. The atomic scale growth mechanisms of PECVD CNT growth, however, remain currently entirely unexplored. In this contribution, we employed molecular dynamics simulations to focus on the effect of applying an electric field on the SWNT growth process, as one of the effects coming into play in PECVD. Using sufficiently strong fields results in (a) alignment of the growing SWNTs, (b) a better ordering of the carbon network, and (c) a higher growth rate relative to thermal growth rate. We suggest that these effects are due to the small charge transfer occurring in the Ni/C system. These simulations constitute the first study of PECVD growth of SWNTs on the atomic level.
Keywords: A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Impact Factor: 13.858
Times cited: 56
DOI: 10.1021/ja2096317
|
“PECVD growth of carbon nanotubes : from experiment to simulation”. Neyts EC, Journal of vacuum science and technology: B: micro-electronics processing and phenomena 30, 030803 (2012). http://doi.org/10.1116/1.3702806
Abstract: Nanostructured carbon materials show a tremendous variety in atomic structure, morphology, properties, and applications. As all properties are ultimately determined by the structure of the material, a thorough understanding of the growth mechanisms that give rise to the particular structure is critical. On many occasions, it has been shown that plasma enhanced growth can be strongly beneficial. This review will describe the authors current understanding of plasma enhanced growth of carbon nanotubes, the prototypical example of nanostructured carbon materials, as obtained from experiments, simulations, and modeling. Specific emphasis is put on where experiments and computational approaches correspond, and where they differ. Also, the current status on simulating PECVD growth of some other carbon nanomaterials is reviewed, including amorphous carbon, graphene, and metallofullerenes. Finally, computational challenges with respect to the simulation of PECVD growth are identified.
Keywords: A1 Journal article; Engineering sciences. Technology; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Times cited: 42
DOI: 10.1116/1.3702806
|
“Effect of a mass spectrometer interface on inductively coupled plasma characteristics : a computational study”. Aghaei M, Lindner H, Bogaerts A, Journal of analytical atomic spectrometry 27, 604 (2012). http://doi.org/10.1039/c2ja10341a
Abstract: An inductively coupled plasma connected to a mass spectrometer interface (sampling cone) is computationally investigated. Typical plasma characteristics, such as gas flow velocity, plasma temperature and electron density, are calculated in two dimensions (cylindrical symmetry) and compared with and without a mass spectrometer sampling interface. The results obtained from our model compare favorably with experimental data reported in the literature. A dramatic increase in the plasma velocity is reported in the region close to the interface. Furthermore, a cooled metal interface lowers the plasma temperature and electron density on the axial channel very close to the sampling cone but the corresponding values in the off axial regions are increased. Therefore, the effect of the interface strongly depends on the measurement position. It is shown that even a small shift from the actual position of the sampler leads to a considerable change of the results.
Keywords: A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Impact Factor: 3.379
Times cited: 18
DOI: 10.1039/c2ja10341a
|
“First-principles simulation of oxygen diffusion in HfOx : role in the resistive switching mechanism”. Clima S, Chen YY, Degraeve R, Mees M, Sankaran K, Govoreanu B, Jurczak M, De Gendt S, Pourtois G, Applied physics letters 100, 133102 (2012). http://doi.org/10.1063/1.3697690
Abstract: Transition metal oxide-based resistor random access memory (RRAM) takes advantage of oxygen-related defects in its principle of operation. Since the change in resistivity of the material is controlled by the oxygen deficiency level, it is of major importance to quantify the kinetics of the oxygen diffusion, key factor for oxide stoichiometry. Ab initio accelerated molecular dynamics techniques are employed to investigate the oxygen diffusivity in amorphous hafnia (HfOx, x = 1.97, 1.0, 0.5). The computed kinetics is in agreement with experimental measurements. (C) 2012 American Institute of Physics. [http://dx.doi.org/10.1063/1.3697690]
Keywords: A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Impact Factor: 3.411
Times cited: 63
DOI: 10.1063/1.3697690
|
“Properties and thermal stability of solution processed ultrathin, high-k bismuth titanate (Bi2Ti2O7) films”. Hardy A, Van Elshocht S, De Dobbelaere C, Hadermann J, Pourtois G, De Gendt S, Afanas'ev VV, Van Bael MK, Materials research bulletin 47, 511 (2012). http://doi.org/10.1016/j.materresbull.2012.01.001
Abstract: Ultrathin bismuth titanate films (Bi2Ti2O7, 5-25 nm) are deposited onto SiO2/Si substrates by aqueous chemical solution deposition and their evolution during annealing is studied. The films crystallize into a preferentially oriented, pure pyrochlore phase between 500 and 700 degrees C, depending on the film thickness and the total thermal budget. Crystallization causes a strong increase of surface roughness compared to amorphous films. An increase of the interfacial layer thickness is observed after anneal at 600 degrees C, together with intermixing of bismuth with the substrate as shown by TEM-EDX. The band gap was determined to be similar to 3 eV from photoconductivity measurements and high dielectric constants between 30 and 130 were determined from capacitance voltage measurements, depending on the processing conditions. (C) 2012 Elsevier Ltd. All rights reserved.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT); Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Impact Factor: 2.446
DOI: 10.1016/j.materresbull.2012.01.001
|
“Quantum simulations of electrostatics in Si cylindrical junctionless nanowire nFETs and pFETs with a homogeneous channel including strain and arbitrary crystallographic orientations”. Pham A-T, Sorée B, Magnus W, Jungemann C, Meinerzhagen B, Pourtois G, Solid state electronics 71, 30 (2012). http://doi.org/10.1016/j.sse.2011.10.016
Abstract: Simulation results of electrostatics in Si cylindrical junctionless nanowire transistors with a homogenous channel are presented. Junctionless transistors including strain and arbitrary crystallographic orientations are studied. Size quantization effects are simulated by self-consistent solutions of the Poisson and Schrodinger equations. The 6 x 6 k.p method is employed for the calculation of the valence subband structure in a junctionless nanowire pFET. The influence of stress/strain and crystallographic channel orientation on to the electrostatics in terms of subband structure, charge density, and C-V curve is systematically studied. (C) 2011 Elsevier Ltd. All rights reserved.
Keywords: A1 Journal article; Condensed Matter Theory (CMT); Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Impact Factor: 1.58
Times cited: 2
DOI: 10.1016/j.sse.2011.10.016
|
“Hyperthermal oxidation of Si(100)2x1 surfaces : effect of growth temperature”. Khalilov U, Pourtois G, van Duin ACT, Neyts EC, The journal of physical chemistry: C : nanomaterials and interfaces 116, 8649 (2012). http://doi.org/10.1021/jp300506g
Abstract: Using reactive molecular dynamics simulations based on the ReaxFF potential, we studied the growth mechanism of ultrathin silica (SiO2) layers during hyperthermal oxidation as a function of temperature in the range 100-1300 K. Oxidation of Si(100){2 x 1} surfaces by both atomic and molecular oxygen was investigated for hyperthermal impact energies in the range of 1 to 5 eV. Two different growth mechanisms are found, corresponding to a low temperature oxidation and a high temperature one. The transition temperature between these mechanisms is estimated to be about 700 K. Also, the initial step of the Si oxidation process is analyzed in detail. Where possible, we validated our results with experimental and ab initio data, and good agreement was obtained. This study is important for the fabrication of silica-based devices in the micro- and nanoelectronics industry and, more specifically, for the fabrication of metal oxide semiconductor devices.
Keywords: A1 Journal article; Engineering sciences. Technology; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Impact Factor: 4.536
Times cited: 32
DOI: 10.1021/jp300506g
|