|
Tan H (2012) From EELS to oxidation state mapping : an investigation into oxidation state mapping of transition metals with electron energy-loss spectroscopy. Antwerpen
Keywords: Doctoral thesis; Electron microscopy for materials research (EMAT)
|
|
|
Shi H (2014) From functional properties to micro/nano-structures : a TEM study of NiTiNb shape memory alloys. Antwerpen
Keywords: Doctoral thesis; Electron microscopy for materials research (EMAT)
|
|
|
“From polyester grafting onto POSS nanocage by ring-opening polymerization to high performance polyester/POSS nanocomposites”. Goffin A-L, Duquesne E, Raquez J-M, Miltner HE, Ke X, Alexandre M, Van Tendeloo G, van Mele B, Dubois P, Journal of materials chemistry 20, 9415 (2010). http://doi.org/10.1039/c0jm00283f
Abstract: Polyester-grafted polyhedral oligomeric silsesquioxane (POSS) nanohybrids selectively produced by ring-opening polymerization of ε-caprolactone and L,L-lactide (A.-L. Goffin, E. Duquesne, S. Moins, M. Alexandre, Ph. Dubois, Eur. Polym. Journal, 2007, 43, 4103) were studied as masterbatches by melt-blending within their corresponding commercial polymeric matrices, i.e., poly(ε-caprolactone) (PCL) and poly(L,L-lactide) (PLA). For the sake of comparison, neat POSS nanoparticles were also dispersed in PCL and PLA. The objective was to prepare aliphatic polyester-based nanocomposites with enhanced crystallization behavior, and therefore, enhanced thermo-mechanical properties. Wide-angle X-ray scattering and transmission electron microscopy attested for the dispersion of individualized POSS nanoparticles in the resulting nanocomposite materials only when the polyester-grafted POSS nanohybrid was used as a masterbatch. The large impact of such finely dispersed (grafted) nanoparticles on the crystallization behavior for the corresponding polyester matrices was noticed, as evidenced by differential scanning calorimetry analysis. Indeed, well-dispersed POSS nanoparticles acted as efficient nucleating sites, significantly increasing the crystallinity degree of both PCL and PLA matrices. As a result, a positive impact on thermo-mechanical properties was highlighted by dynamic mechanical thermal analysis.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Times cited: 42
DOI: 10.1039/c0jm00283f
|
|
|
“From the lattice measurements of the austenite and the martensite cells to the macroscopic mechanical behavior of shape memory alloys”. Lexcellent C, Vivet A, Bouvet C, Blanc P, Satto C, Schryvers D, Journal de physique: 4 11, 317 (2001)
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
|
|
|
Ke X (2010) From top-down to bottom-up : from carbon nanotubes to nanodevices. Antwerpen
Keywords: Doctoral thesis; Electron microscopy for materials research (EMAT)
|
|
|
Khaletskaya K (2014) Functional metal-organic frameworks : from bulk to surface engineered properties. Antwerpen
Keywords: Doctoral thesis; Electron microscopy for materials research (EMAT)
|
|
|
“Gas-phase loading of [Zn4O(btb)2] (MOF-177) with organometallic CVD-precursors: inclusion compounds of the type [LnM]a@MOF-177 and the formation of Cu and Pd nanoparticles inside MOF-177”. Müller M, Lebedev OI, Fischer RA, Journal of materials chemistry 18, 5274 (2008). http://doi.org/10.1039/b810989c
Abstract: The highly porous and desolvated (activated) coordination polymer [Zn4O(btb)2] (btb = benzene-1,3,5-tribenzoate; MOF-177) was loaded with the organometallic compounds [Cp2Fe], [Cp*2Zn], [Cu(OCHMeCH2NMe2)2], [CpCuL] (L = PMe3, CNtBu) and [CpPd(3-C3H5)] via solvent-free adsorption from the gas-phase. The inclusion compounds of the type [LnM]a@MOF-177, where [LnM] indicates the respective compound and the parameter a denotes the number of molecules per formula unit of the MOF-177, were characterised by elemental analysis, FT-IR, solid-state NMR spectroscopy and by powder X-ray diffraction (PXRD). Remarkably high effective loadings of up to 11 molecules [Cp2Fe] and 10 molecules [CpPd(3-C3H5)] per cavity were determined. The analytical data prove that the host lattice and the guest molecules interact only by weak van-der-Waals forces without any significant change of the framework or the chemical nature of the included molecules. Cu nanoparticles showing the typical surface plasmon resonance at 580 nm and Pd nanoparticles of about 2.6 nm in size were formed inside the cavities of MOF-177 by the thermally activated hydrogenolysis of the inclusion compounds [CpCuCNtBu]2@MOF-177 and by photolysis of [CpPd(3-C3H5)]10@MOF-177 in an inert atmosphere (Ar). PXRD, FT-IR and NMR studies revealed that the MOF-177 matrix remained unchanged during the decomposition process of the precursors. N2 adsorption studies of the obtained materials Cu@MOF-177 (e.g. 10.6 wt.% Cu, 2309 m2 g-1) and Pd@MOF-177 (e.g. 32.5 wt.%, 1063 m2 g-1) reveal high remaining specific surface areas (Langmuir model).
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Times cited: 65
DOI: 10.1039/b810989c
|
|
|
“Gold particles supported on TiO2”. Giorgio S, Henry CR, Pauwels B, Van Tendeloo G, , 369 (2000)
Keywords: P3 Proceeding; Electron microscopy for materials research (EMAT)
|
|
|
“Granular films assembled of CoN, CrM and mixtures of CoN and CrM clusters: structure and electron transport properties”. Kuhn LT, Vanhoutte F, Cannaerts M, Neukermans S, Verschoren G, Bouwen W, van Haesendonck C, Lievens P, Silverans RE, Pauwels B, Van Tendeloo G, (2000)
Keywords: P3 Proceeding; Electron microscopy for materials research (EMAT)
|
|
|
“Growth mechanism of biaxially aligned magnesium oxide deposited by unbalanced magnetron sputtering”. Ghekiere P, Mahieu S, De Winter G, De Gryse R, Depla D, Lebedev OI, Diffusion and defect data : solid state data : part B : solid state phenomena
T2 –, 2nd International Conference on Texture and Anisotropy of Polycrystals, JUL 07-09, 2004, Metz, FRANCE 105, 433 (2005). http://doi.org/10.4028/www.scientific.net/SSP.105.433
Abstract: For many years magnesium oxide (MgO) has been a topic of research as buffer layer for high-temperature superconducting copper oxides and as protective layer in plasma display panels. Since epitaxial growth of MgO is expensive, time consuming and size restricted, other techniques have been developed to grow highly oriented MgO layers for industrial processes. MgO thin films were deposited on a tilted polycrystalline substrate by reactive sputtering using an unbalanced magnetron. By varying different deposition parameters, it is possible to grow biaxially aligned MgO layers, i.e. layers with both out-of-plane and in-plane alignment. XRD measurements were performed to examine the crystallographic structure of the thin film. The preferential out-of-plane orientation is analysed by angular scans using the peak intensity of different reflections while the in-plane orientation is determined by (002) pole figures. Fully [111] out-of-plane oriented layers were grown with a strong in-plane alignment. SEM and TEM measurements were performed to reveal the topographical and cross-sectional microstructure and to investigate the texture evolution of the MgO layers. Evolutionary columnar growth and a roof-tile surface have been observed.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Times cited: 5
DOI: 10.4028/www.scientific.net/SSP.105.433
|
|
|
“Growth of R1+xBa2-xCu3O7-\delta epitaxial films investigated by in situ scanning tunneling microscopy”. Salluzzo M, Aruta C, Maggio-Aprile I, Fischer Ø, Bals S, Zegenhagen J, Physica status solidi: A: applied research 186, 339 (2001). http://doi.org/10.1002/1521-396X(200108)186:3<339::AID-PSSA339>3.0.CO;2-5
Abstract: The problem of the epitaxial growth of the high temperature superconducting R1+xBa2xCu3O7δ (R = Y or rare earth except Ce and Tb) films has been addressed. Using in situ ultra high vacuum Scanning Tunneling Microscopy (UHV-STM) we have studied the role of cationic substitution and substrate mismatch on the growth mode of stoichiometric and Nd-rich Nd1+xBa2xCu3O7δ thin films. The results are compared to the growth of Y1Ba2Cu3O7δ, Dy1Ba2Cu3O7δ and Gd1Ba2Cu3O7δ epitaxial films. Two main phenomena are investigated: a) the first stage of the direct nucleation on the substrate and b) the crossover between 2D and 3D growth upon increasing the film thickness. At the first stage of the growth, pseudo-cubic perovskite (Re,Ba)CuO3 nuclei are formed. While they disappear after the growth of a few nm in stoichiometric films, they persist on the surface of Nd-rich films of up to 110 nm thickness. Stoichiometric R1+xBa2xCu3O7δ films exhibit a rough morphology with increasing thickness due to island growth mode, whereas Nd-rich films remain smooth and continue to grow layer by layer. It is proposed that linear defects (like anti-phase boundaries), which are formed due to the misalignment of growth fronts, are the source of screw dislocations in stoichiometric films. In Nd-rich films, linear defects are eliminated through the insertion of (Nd,Ba)CuO3 extra layers without introduction of any screw dislocations.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Times cited: 17
DOI: 10.1002/1521-396X(200108)186:3<339::AID-PSSA339>3.0.CO;2-5
|
|
|
Amelinckx S, van Dyck D, van Landuyt J, Van Tendeloo G (1997) Handbook of microscopy: applications in materials science, solid-state physics and chemistry. Vch, Weinheim
Keywords: ME1 Book as editor or co-editor; Electron microscopy for materials research (EMAT); Vision lab
|
|
|
“High electron mobility in AlGaN/GaN HEMT grown on sapphire: strain modification by means of AIN interlayers”. Germain M, Leys M, Boeykens S, Degroote S, Wang W, Schreurs D, Ruythooren W, Choi K-H, van Daele B, Van Tendeloo G, Borghs G, Materials Research Society symposium proceedings 798, Y10.22 (2004)
Keywords: P1 Proceeding; Electron microscopy for materials research (EMAT)
|
|
|
“High precision determination of the elastic strain of InGaN/GaN multiple quantum wells”. Wu MF, Zhou S, Yao S, Zhao Q, Vantomme A, van Daele B, Piscopiello E, Van Tendeloo G, Tong YZ, Yang ZJ, Yu TJ, Zhang GY, Journal of vacuum science and technology: B: microelectronics and nanometer structures 22, 920 (2004). http://doi.org/10.1116/1.1715085
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Times cited: 15
DOI: 10.1116/1.1715085
|
|
|
“High resolution electron microscopy in materials research”. Van Tendeloo G, Journal of materials chemistry 8, 797 (1998). http://doi.org/10.1039/a708240a
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Times cited: 8
DOI: 10.1039/a708240a
|
|
|
“High-resolution electron microscopy study of strained epitaxial La0.7Sr0.3MnO3 thin films”. Lebedev OI, Van Tendeloo G, Amelinckx S, Ju HL, Krishnan KM, Philosophical magazine: A: physics of condensed matter: defects and mechanical properties 80, 673 (2000). http://doi.org/10.1080/01418610008212075
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Times cited: 52
DOI: 10.1080/01418610008212075
|
|
|
“High resolution TEM observation of in situ colloid formation in CaF2 crystals”. Teodorescu VS, Nistor LC, van Landuyt J, Materials science forum 239-241, 671 (1997)
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Times cited: 3
|
|
|
“High resolution transmission electron microscopy study of nanoscale Ni-rich Ni-Al films evaporated onto NaCl and KCl”. Yandouzi M, Toth L, Schryvers D, Nanostructured materials 10, 99 (1998). http://doi.org/10.1016/S0965-9773(98)00025-7
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Times cited: 2
DOI: 10.1016/S0965-9773(98)00025-7
|
|
|
“High-resolution visualization techniques : structural aspects”. Schryvers D, Van Aert S Springer, Berlin, page 135 (2012).
Keywords: H1 Book chapter; Electron microscopy for materials research (EMAT)
|
|
|
“HREM for characterisation of nanoscale microstructures”. van Landuyt J, Van Tendeloo G, , 15 (1998)
Keywords: P3 Proceeding; Electron microscopy for materials research (EMAT)
|
|
|
“HREM investigation of a Fe/GaN/Fe tunnel junction”. Nistor L, Bender H, van Landuyt J, Nemeth S, Boeve H, De Boeck J, Borghs G, Institute of physics conference series
T2 –, Royal-Microscopical-Society Conference on Microscopy of Semiconducting, Materials, MAR 25-29, 2001, Univ of Oxford, Oxford, England , 53 (2001)
Abstract: The structure of Fe/GaN/Fe ferromagnetic electrodes is studied by high resolution transmission electron microscopy. The layers grow epitaxially on the GaAs substrate with the top Fe layer 90degrees rotated compared to the bottom one. The interfaces are quite rough. There is an indication of the possible occurrence of Fe3GaAs formation on the GaAs interface.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
|
|
|
“HREM investigation of La(1-x)Ca(x)MnO3-delta thin films”. Lebedev O, Van Tendeloo G, Amelinckx S, Leibold B, Habermeier HU, , 517 (1998)
Keywords: P1 Proceeding; Electron microscopy for materials research (EMAT)
|
|
|
“HREM investigation of La1-xCaxMnO3- thin films”. Lebedev OI, Van Tendeloo G, Amelinckx S, Leibold B, Habermeier H-U, Electron microscopy: vol. 2 , 517 (1998)
Keywords: A3 Journal article; Electron microscopy for materials research (EMAT)
|
|
|
“HREM of defects in cubic boron nitride single crystals”. Nistor LC, van Landuyt J, Dincã, G, , 695 (1998)
Keywords: P1 Proceeding; Electron microscopy for materials research (EMAT)
|
|
|
“HREM study of ion implantation in 6H-SiC at high temperatures”. Lebedev OI, Van Tendeloo G, Suvorova AA, Usov IO, Suvorov AV, Journal of electron microscopy 46, 271 (1997)
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 0.9
Times cited: 7
|
|
|
“HRTEM studies of dislocations in cubic BN”. Nistor LC, Van Tendeloo G, Dincã, G, Physica status solidi: A: applied research 201, 2578 (2004). http://doi.org/10.1002/pssa.200405192
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Times cited: 8
DOI: 10.1002/pssa.200405192
|
|
|
“HRTEM study of austenite and martensite in splat-cooled and nanoscale thin film Ni-Al”. Schryvers D, Yandouzi M, Holland-Moritz D, Toth L, Journal de physique: 4 C5, 203 (1997). http://doi.org/10.1051/jp4:1997532
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Times cited: 2
DOI: 10.1051/jp4:1997532
|
|
|
“Identification of new superconducting compounds by electron microscopy”. Van Tendeloo G, Krekels T Cambridge University Press, Cambridge, page 161 (2000).
Keywords: H3 Book chapter; Electron microscopy for materials research (EMAT)
|
|
|
Sarmadian N (2015) Identification of thin-film photovoltaic cell materials based on high-throughput first-principles calculations. Antwerpen
Keywords: Doctoral thesis; Electron microscopy for materials research (EMAT)
|
|
|
“Improvement of the oxidation stability and the mechanical properties of flexible graphite foil by boron oxide impregnation”. Savchenko DV, Serdan AA, Morozov VA, Van Tendeloo G, Ionov SG, New carbon materials 27, 12 (2012). http://doi.org/10.1016/S1872-5805(12)60001-8
Abstract: Flexible graphite foil produced by rolling expanded graphite impregnated with boron oxide was analyzed by laser mass spectroscopy, X-ray photoelectron spectroscopy, scanning electron microscopy and thermogravimetry. It was shown that the modification of the graphite foil by boron oxide increases the onset temperature of oxidation by ∼ 150 °C. Impregnation of less than 2 mass% boron oxide also increased the tensile strength of the materials. The observed improvement was attributed to the blocking of active sites by boron oxide, which is probably chemically bonded to the edges of graphene sheets in expanded graphite particles.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Times cited: 5
DOI: 10.1016/S1872-5805(12)60001-8
|
|