|
Records |
|
Author |
Penders, A.; Konstantinovic, M.J.; Bosch, R.W.; Schryvers, D. |
|
Title |
Crack initiation in tapered high Si stainless steel specimens : stress threshold analyses |
Type |
A1 Journal article |
|
Year |
2020 |
Publication |
Corrosion Engineering Science And Technology |
Abbreviated Journal |
Corros Eng Sci Techn |
|
Volume |
|
Issue |
|
Pages |
1-8 |
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
|
Abstract |
Tapered specimens were used for an accelerated test technique to study the crack initiation of high Si stainless steel by means of constant elongation rate tensile testing in a simulated pressurised water reactor environment. Detailed crack density distributions were obtained by applying an advanced crack detection algorithm on iteratively displaced scanning electron microscopy pictures featuring stress corrosion cracks along the specimen's gauge length. By means of finite-element analysis, prominent peaks in the crack density graphs are demonstrated to be related to stress relief and stress build-up during the crack initiation phase. Intrinsic scatter related to the crack detection suggests that stress corrosion cracking is independent of the strain-rate for strain-rates lower than 10(-6 )s(-1). Based on the extrapolation to constant load conditions, the critical threshold value for the duplex high Si stainless steel is estimated to be around 580 MPa. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
Language |
|
Wos |
000549651600001 |
Publication Date |
2020-06-30 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
1478-422x |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
1.8 |
Times cited |
1 |
Open Access |
Not_Open_Access |
|
Notes |
; We would like to acknowledge ENGIE Electrabel for the financial support of this work under the contract number BSUEZ5500. ; |
Approved |
Most recent IF: 1.8; 2020 IF: 0.879 |
|
Call Number |
UA @ admin @ c:irua:171292 |
Serial |
6478 |
Permanent link to this record |
|
|
|
|
Author |
Molina-Luna, L.; Duerrschnabel, M.; Turner, S.; Erbe, M.; Martinez, G.T.; Van Aert, S.; Holzapfel, B.; Van Tendeloo, G. |
|
Title |
Atomic and electronic structures of BaHfO3-doped TFA-MOD-derived YBa2Cu3O7−δthin films |
Type |
A1 Journal article |
|
Year |
2015 |
Publication |
Superconductor science and technology |
Abbreviated Journal |
Supercond Sci Tech |
|
Volume |
28 |
Issue |
28 |
Pages |
115009 |
|
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
Abstract |
Tailoring the properties of oxide-based nanocomposites is of great importance for a wide range of materials relevant for energy technology. YBa2Cu3O7−δ (YBCO) superconducting thin films containing nanosized BaHfO3 (BHO) particles yield a significant improvement of the magnetic flux pinning properties and a reduced anisotropy of the critical current density. These films were prepared by chemical solution deposition (CSD) on (100) SrTiO3 (STO) substrates yielding critical current densities up to 3.6 MA cm−2 at 77 K and self-field. Transport in-field J c measurements demonstrated a high pinning force maximum of around 6 GN/m3 for a sample annealed at T = 760 °C that has a doping of 12 mol% of BHO. This sample was investigated by scanning transmission electron microscopy (STEM) in combination with electron energy-loss spectroscopy (EELS) yielding strain and spectral maps. Spherical BHO nanoparticles of 15 nm in size were found in the matrix, whereas the particles at the interface were flat. A 2 nm diffusion layer containing Ti was found at the YBCO (BHO)/STO interface. Local lattice deformation mapping at the atomic scale revealed crystal defects induced by the presence of both sorts of BHO nanoparticles, which can act as pinning centers for magnetic flux lines. Two types of local lattice defects were identified and imaged: (i) misfit edge dislocations and (ii) Ba-Cu-Cu-Ba stacking faults (Y-248 intergrowths). The local electronic structure and charge transfer were probed by high energy resolution monochromated electron energy-loss spectroscopy. This technique made it possible to distinguish superconducting from non-superconducting areas in nanocomposite samples with atomic resolution in real space, allowing the identification of local pinning sites on the order of the coherence length of YBCO (~1.5 nm) and the determination of 0.25 nm dislocation cores. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
Language |
|
Wos |
000366193000018 |
Publication Date |
2015-09-25 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
0953-2048;1361-6668; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
2.878 |
Times cited |
4 |
Open Access |
|
|
Notes |
The authors thank financial support from the European Union under the Framework 6 program as a contract for an Integrated Infrastructure Initiative (References No. 026019 ESTEEM) and by the EUFP6 Research Project “NanoEngineered Superconductors for Power Applications” NESPA no. MRTN-CT-2006-035619. This work was supported by funding from the European Research Council under the Seventh Framework Programme (FP7). L.M.L, S.T. and G.V.T acknowledge ERC grant N°246791 – COUNTATOMS and funding under a contract for an Integrated Infrastructure Initiative, Reference No. 312483- ESTEEM2, as well as the EC project EUROTAPES. G.T.M. and S.V.A acknowledge financial support from the Fund for Scientific Research-Flanders (Reference G.0064.10N and G.0393.11N). M.D. acknowledges financial support from the LOEWE research cluster RESPONSE (Hessen, Germany). M.E. has received funding from the European Union Seventh Framework Programme (FP7/2007–2013) under grant agreement n° NMP-LA-2012-280432.; esteem2jra2; esteem2jra3 |
Approved |
Most recent IF: 2.878; 2015 IF: 2.325 |
|
Call Number |
c:irua:129199 c:irua:129199 |
Serial |
3942 |
Permanent link to this record |
|
|
|
|
Author |
Van Cauwenbergh, P.; Samaee, V.; Thijs, L.; Nejezchlebova, J.; Sedlak, P.; Ivekovic, A.; Schryvers, D.; Van Hooreweder, B.; Vanmeensel, K. |
|
Title |
Unravelling the multi-scale structure-property relationship of laser powder bed fusion processed and heat-treated AlSi10Mg |
Type |
A1 Journal article |
|
Year |
2021 |
Publication |
Scientific Reports |
Abbreviated Journal |
Sci Rep-Uk |
|
Volume |
11 |
Issue |
1 |
Pages |
6423 |
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
|
Abstract |
Tailoring heat treatments for Laser Powder Bed Fusion (LPBF) processed materials is critical to ensure superior and repeatable material properties for high-end applications. This tailoring requires in-depth understanding of the LPBF-processed material. Therefore, the current study aims at unravelling the threefold interrelationship between the process (LPBF and heat treatment), the microstructure at different scales (macro-, meso-, micro-, and nano-scale), and the macroscopic material properties of AlSi10Mg. A similar solidification trajectory applies at different length scales when comparing the solidification of AlSi10Mg, ranging from mould-casting to rapid solidification (LPBF). The similarity in solidification trajectories triggers the reason why the Brody-Flemings cellular microsegregation solidification model could predict the cellular morphology of the LPBF as-printed microstructure. Where rapid solidification occurs at a much finer scale, the LPBF microstructure exhibits a significant grain refinement and a high degree of silicon (Si) supersaturation. This study has identified the grain refinement and Si supersaturation as critical assets of the as-printed microstructure, playing a vital role in achieving superior mechanical and thermal properties during heat treatment. Next, an electrical conductivity model could accurately predict the Si solute concentration in LPBF-processed and heat-treated AlSi10Mg and allows understanding the microstructural evolution during heat treatment. The LPBF-processed and heat-treated AlSi10Mg conditions (as-built (AB), direct-aged (DA), stress-relieved (SR), preheated (PH)) show an interesting range of superior mechanical properties (tensile strength: 300-450 MPa, elongation: 4-13%) compared to the mould-cast T6 reference condition. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
Language |
|
Wos |
000632047000003 |
Publication Date |
2021-03-19 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
2045-2322 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
4.259 |
Times cited |
|
Open Access |
OpenAccess |
|
Notes |
|
Approved |
Most recent IF: 4.259 |
|
Call Number |
UA @ admin @ c:irua:177634 |
Serial |
6791 |
Permanent link to this record |
|
|
|
|
Author |
Dendooven, J.; Ramachandran, R.K.; Solano, E.; Kurttepeli, M.; Geerts, L.; Heremans, G.; Ronge, J.; Minjauw, M.M.; Dobbelaere, T.; Devloo-Casier, K.; Martens, J.A.; Vantomme, A.; Bals, S.; Portale, G.; Coati, A.; Detavernier, C. |
|
Title |
Independent tuning of size and coverage of supported Pt nanoparticles using atomic layer deposition |
Type |
A1 Journal article |
|
Year |
2017 |
Publication |
Nature communications |
Abbreviated Journal |
Nat Commun |
|
Volume |
8 |
Issue |
8 |
Pages |
1074 |
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
|
Abstract |
Synthetic methods that allow for the controlled design of well-defined Pt nanoparticles are highly desirable for fundamental catalysis research. In this work, we propose a strategy that allows precise and independent control of the Pt particle size and coverage. Our approach exploits the versatility of the atomic layer deposition (ALD) technique by combining two ALD processes for Pt using different reactants. The particle areal density is controlled by tailoring the number of ALD cycles using trimethyl(methylcyclopentadienyl) platinum and oxygen, while subsequent growth using the same Pt precursor in combination with nitrogen plasma allows for tuning of the particle size at the atomic level. The excellent control over the particle morphology is clearly demonstrated by means of in situ and ex situ X-ray fluorescence and grazing incidence small angle X-ray scattering experiments, providing information about the Pt loading, average particle dimensions, and mean center-to-center particle distance. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
Language |
|
Wos |
000413353500023 |
Publication Date |
2017-10-16 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
2041-1723 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
12.124 |
Times cited |
88 |
Open Access |
OpenAccess |
|
Notes |
; This research was funded by the Research Foundation-Flanders (FWO), the Special Research Fund BOF of Ghent University (GOA 01G01513) and the Flemish Government (Medium-scale research infrastructure funding-Hercules funding). J. D., T. D. and M. M. M. acknowledge the FWO for a research fellowship. S. B. acknowledges the European Research Council, ERC grant no. 335078-Colouratom. For the GISAXS and XRF measurements at SOLEIL, the authors received funding from the European Community's Trans National Access Program CALIPSO. We are also grateful to the SOLEIL and ESRF staff for smoothly running the facilities. The authors thank G. Verellen for his help with drawing the 3D sketches. ; ecas_Sara |
Approved |
Most recent IF: 12.124 |
|
Call Number |
UA @ lucian @ c:irua:146668UA @ admin @ c:irua:146668 |
Serial |
4786 |
Permanent link to this record |
|
|
|
|
Author |
Missen, O.P.; Mills, S.J.; Canossa, S.; Hadermann, J.; Nenert, G.; Weil, M.; Libowitzky, E.; Housley, R.M.; Artner, W.; Kampf, A.R.; Rumsey, M.S.; Spratt, J.; Momma, K.; Dunstan, M.A. |
|
Title |
Polytypism in mcalpineite : a study of natural and synthetic Cu₃TeO₆ |
Type |
A1 Journal article |
|
Year |
2022 |
Publication |
Acta Crystallographica. Section B: Structural Science, Crystal Engineering and Materials (Online) |
Abbreviated Journal |
Acta Crystallogr B |
|
Volume |
78 |
Issue |
1 |
Pages |
|
|
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
Abstract |
Synthetic and naturally occurring forms of tricopper orthotellurate, (Cu3TeO6)-Te-II-O-IV (the mineral mcalpineite) have been investigated by 3D electron diffraction (3D ED), X-ray powder diffraction (XRPD), Raman and infrared (IR) spectroscopic measurements. As a result of the diffraction analyses, (Cu3TeO6)-Te-II-O-IV is shown to occur in two polytypes. The higher-symmetric (Cu3TeO6)-Te-II-O-IV-1C polytype is cubic, space group 1a (3) over bar, with a = 9.537 (1) angstrom and V = 867.4 (3) angstrom(3) as reported in previous studies. The 1C polytype is a well characterized structure consisting of alternating layers of (CuO6)-O-II octahedra and both (CuO6)-O-II and (TeO6)-O-VI octahedra in a patchwork arrangement. The structure of the lower-symmetric orthorhombic (Cu3TeO6)-Te-II-O-IV-2O polytype was determined for the first time in this study by 3D ED and verified by Rietveld refinement. The 2O polytype crystallizes in space group Pcca, with a = 9.745 (3) angstrom, b = 9.749 (2) angstrom, c = 9.771 (2) angstrom and V = 928.3 (4) angstrom(3) . High-precision XRPD data were also collected on (Cu3TeO6)-Te-II-O-IV-2O to verify the lower-symmetric structure by performing a Rietveld refinement. The resultant structure is identical to that determined by 3D ED, with unit-cell parameters a = 9.56157 (19) angstrom, b = 9.55853 (11) angstrom, c = 9.62891 (15) angstrom and V = 880.03 (2) angstrom(3) . The lower symmetry of the 2O polytype is a consequence of a different cation ordering arrangement, which involves the movement of every second (CuO6)-O-II and (TeO6)-O-VI octahedral layer by (1/4, 1/4, 0), leading to an offset of (TeO6)-O-VI and (CuO6)-O-II octahedra in every second layer giving an ABAB* stacking arrangement. Syntheses of (Cu3TeO6)-Te-II-O-IV showed that low-temperature (473 K) hydrothermal conditions generally produce the 2O polytype. XRPD measurements in combination with Raman spectroscopic analysis showed that most natural mcalpineite is the orthorhombic 2O polytype. Both XRPD and Raman spectroscopy measurements may be used to differentiate between the two polytypes of (Cu3TeO6)-Te-II-O-IV. In Raman spectroscopy, (Cu3TeO6)-Te-II-O-IV-1C has a single strong band around 730 cm(-1), whereas (Cu3TeO6)-Te-II-O-IV-2O shows a broad double maximum with bands centred around 692 and 742 cm(-1). |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
Language |
|
Wos |
000752899700003 |
Publication Date |
2022-01-18 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
2052-5206 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
1.9 |
Times cited |
|
Open Access |
OpenAccess |
|
Notes |
|
Approved |
Most recent IF: 1.9 |
|
Call Number |
UA @ admin @ c:irua:186529 |
Serial |
6962 |
Permanent link to this record |
|
|
|
|
Author |
van der Stam, W.; Gradmann, S.; Altantzis, T.; Ke, X.; Baldus, M.; Bals, S.; de Mello Donega, C. |
|
Title |
Shape Control of Colloidal Cu2-x S Polyhedral Nanocrystals by Tuning the Nucleation Rates |
Type |
A1 Journal article |
|
Year |
2016 |
Publication |
Chemistry of materials |
Abbreviated Journal |
Chem Mater |
|
Volume |
28 |
Issue |
28 |
Pages |
6705-6715 |
|
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
Abstract |
Synthesis protocols for colloidal nanocrystals (NCs) with narrow size and shape distributions are of particular interest for the successful implementation of these nanocrystals into devices. Moreover, the preparation of NCs with well-defined crystal phases is of key importance. In this work, we show that Sn(IV)-thiolate complexes formed in situ strongly influence the nucleation and growth rates of colloidal Cu2-x S polyhedral NCs, thereby dictating their final size, shape, and crystal structure. This allowed us to successfully synthesize hexagonal bifrustums and hexagonal bipyramid NCs with low-chalcocite crystal structure, and hexagonal nanoplatelets with various thicknesses and aspect ratios with the djurleite crystal structure, by solely varying the concentration of Sn(IV)-additives (namely, SnBr4) in the reaction medium. Solution and solid-state 119Sn NMR measurements show that SnBr4 is converted in situ to Sn(IV)-thiolate complexes, which increase the Cu2-x S nucleation barrier without affecting the precursor conversion rates. This influences both the nucleation and growth rates in a concentration-dependent fashion and leads to a better separation between nucleation and growth. Our approach of tuning the nucleation and growth rates with in situ-generated Sn-thiolate complexes might have a more general impact due to the availability of various metal-thiolate complexes, possibly resulting in polyhedral NCs of a wide variety of metal-sulfide compositions. |
|
Address |
Condensed Matter and Interfaces, Debye Institute for Nanomaterials Science, Utrecht University , P.O. Box 80000, 3508 TA Utrecht, The Netherlands |
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
Language |
English |
Wos |
000384399000037 |
Publication Date |
2016-09-02 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
0897-4756 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
9.466 |
Times cited |
27 |
Open Access |
OpenAccess |
|
Notes |
W.v.d.S. and C.d.M.D. acknowledge financial support from the division of Chemical Sciences (CW) of The Netherlands Organization for Scientific Research (NWO) under grant number ECHO.712.012.001. M.B. also gratefully acknowledges NWO for funding the NMR infrastructure (Middle Groot program, grant number 700.58.102). S.B. acknowledges financial support from the European Research Council (ERC Starting Grant # 335078-COLOURATOMS).; ECAS_Sara; (ROMEO:white; preprint:; postprint:restricted 12 months embargo; pdfversion:cannot); |
Approved |
Most recent IF: 9.466 |
|
Call Number |
EMAT @ emat @ c:irua:135928 |
Serial |
4285 |
Permanent link to this record |
|
|
|
|
Author |
Xia, C.; Winckelmans, N.; Prins, P.T.; Bals, S.; Gerritsen, H.C.; de Mello Donegá, C. |
|
Title |
Near-Infrared-Emitting CuInS2/ZnS Dot-in-Rod Colloidal Heteronanorods by Seeded Growth |
Type |
A1 Journal article |
|
Year |
2018 |
Publication |
Journal of the American Chemical Society |
Abbreviated Journal |
J Am Chem Soc |
|
Volume |
140 |
Issue |
140 |
Pages |
5755-5763 |
|
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
Abstract |
Synthesis protocols for anisotropic CuInX2 (X = S, Se, Te)-based heteronanocrystals (HNCs) are scarce due to the difficulty in balancing the reactivities of multiple precursors and the high solid-state diffusion rates of the cations involved in the CuInX2 lattice. In this work, we report a multistep seeded growth synthesis protocol that yields colloidal wurtzite CuInS2/ZnS dot core/rod shell HNCs with photoluminescence in the NIR (∼800 nm). The wurtzite CuInS2 NCs used as seeds are obtained by topotactic partial Cu+ for In3+ cation exchange in template Cu2–xS NCs. The seed NCs are injected in a hot solution of zinc oleate and hexadecylamine in octadecene, 20 s after the injection of sulfur in octadecene. This results in heteroepitaxial growth of wurtzite ZnS primarily on the Sulfur-terminated polar facet of the CuInS2 seed NCs, the other facets being overcoated only by a thin (∼1 monolayer) shell. The fast (∼21 nm/min) asymmetric axial growth of the nanorod proceeds by addition of [ZnS] monomer units, so that the polarity of the terminal (002) facet is preserved throughout the growth. The delayed injection of the CuInS2 seed NCs is crucial to allow the concentration of [ZnS] monomers to build up, thereby maximizing the anisotropic heteroepitaxial growth rates while minimizing the rates of competing processes (etching, cation exchange, alloying). Nevertheless, a mild etching still occurred, likely prior to the onset of heteroepitaxial overgrowth, shrinking the core size from 5.5 to ∼4 nm. The insights provided by this work open up new possibilities in designing multifunctional Cu-chalcogenide based colloidal heteronanocrystals. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
Language |
|
Wos |
000431600000016 |
Publication Date |
2018-03-29 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
0002-7863 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
13.858 |
Times cited |
43 |
Open Access |
OpenAccess |
|
Notes |
Chenghui Xia acknowledges China Scholarship Council (CSC) for financial support (NO. 201406330055). S.B and N.W. acknowledge funding from the European Research Council (Starting Grant No. COLOURATOMS 335078). C.d.M.D. acknowledge financial support from the division of Chemical Sciences (CW) of The Netherlands Organization for Scientific Research (NWO) under Grant Number ECHO.712.014.001. The authors thank Xiaobin Xie and Da Wang for some TEM measurements, Donglong Fu for XRD measurements, Christina H. M. van Oversteeg for ICP-OES measurements, and Chun-Che Lin for suggestions regarding the synthesis. ECAS_Sara (ROMEO:white; preprint:; postprint:restricted 12 months embargo; pdfversion:cannot); |
Approved |
Most recent IF: 13.858 |
|
Call Number |
EMAT @ emat @c:irua:150362UA @ admin @ c:irua:150362 |
Serial |
4917 |
Permanent link to this record |
|
|
|
|
Author |
Shenderova, O.; Vargas, A.; Turner, S.; Ivanov, D.M.; Ivanov, M.G. |
|
Title |
Nanodiamond-based nanolubricants : investigation of friction surfaces |
Type |
A1 Journal article |
|
Year |
2014 |
Publication |
Tribology transactions |
Abbreviated Journal |
Tribol T |
|
Volume |
57 |
Issue |
6 |
Pages |
1051-1057 |
|
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
Abstract |
Synergistic compositions of detonation nanodiamond (DND) particles with polytetrafluoroethylene and molybdenum dialkyldithiophosphate were used in ring-on-ring, four-ball, and block-on-ring tests as an additive to polyalphaolefins and engine oils. Modest to significant reductions in the friction coefficients, wear, or both were observed. In the wear scars produced in the block-on-ring tests, the friction surfaces were characterized by scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), and profilometry. Significant polishing effects of the friction surfaces in lubricants containing DND were revealed in SEM observations and roughness measurements. The roughness of the scar surfaces produced in the presence of DND additives was about 35% lower than the roughness of the scars observed in pure oil experiments. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
Park Ridge, Ill. |
Editor |
|
|
Language |
|
Wos |
000345317900009 |
Publication Date |
2014-06-26 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
1040-2004;1547-397X; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
1.685 |
Times cited |
23 |
Open Access |
|
|
Notes |
|
Approved |
Most recent IF: 1.685; 2014 IF: 1.349 |
|
Call Number |
UA @ lucian @ c:irua:122161 |
Serial |
2252 |
Permanent link to this record |
|
|
|
|
Author |
Tang, Y.; Chen, Z.; Borbely, A.; Ji, G.; Zhong, S.Y.; Schryvers, D.; Ji, V.; Wang, H.W. |
|
Title |
Quantitative study of particle size distribution in an in-situ grown Al-TiB2 composite by synchrotron X-ray diffraction and electron microscopy |
Type |
A1 Journal article |
|
Year |
2015 |
Publication |
Materials characterization |
Abbreviated Journal |
Mater Charact |
|
Volume |
102 |
Issue |
102 |
Pages |
131-136 |
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
|
Abstract |
Synchrotron X-ray diffraction and transmission electron microscopy (TEM) were applied to quantitatively characterize the average particle size and size distribution of free-standing TiB2 particles and TiB2 particles in an insitu grown Al–TiB2 composite. The detailed evaluations were carried out by X-ray line profile analysis using the restrictedmoment method and multiplewhole profile fitting procedure (MWP). Both numericalmethods indicate that the formed TiB2 particles are well crystallized and free of crystal defects. The average particle size determined from different Bragg reflections by the restricted moment method ranges between 25 and 55 nm, where the smallest particle size is determined using the 110 reflection suggesting the highest lateral-growth velocity of (110) facets. TheMWP method has shown that the in-situ grown TiB2 particles have a very low dislocation density (~1011 m−2) and their size distribution can be described by a log-normal distribution. Good agreement was found between the results obtained from the restricted moment and MWP methods, which was further confirmed by TEM. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
New York |
Editor |
|
|
Language |
|
Wos |
000355335200017 |
Publication Date |
2015-03-04 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
1044-5803; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
2.714 |
Times cited |
41 |
Open Access |
|
|
Notes |
This work is financially supported by the National Natural Science Foundation of China (Grant No. 51201099 and No. 51301108) and the China Postdoctoral Science Foundation (Grant No. 2013T60443 and No. 2012M520891). The authors are grateful for the project 2013BB03 supported by NPL, CAEP. Many thanks are also due to the faculty of BL14B beamline at the Shanghai Synchrotron Radiation Facility for their help on synchrotron experiments. |
Approved |
Most recent IF: 2.714; 2015 IF: 1.845 |
|
Call Number |
c:irua:126443 |
Serial |
2764 |
Permanent link to this record |
|
|
|
|
Author |
Aerts, A.; Follens, L.R.A.; Biermans, E.; Bals, S.; Van Tendeloo, G.; Loppinet, B.; Kirschhock, C.E.A.; Martens, J.A. |
|
Title |
Modelling of synchrotron SAXS patterns of silicalite-1 zeolite during crystallization |
Type |
A1 Journal article |
|
Year |
2011 |
Publication |
Physical chemistry, chemical physics |
Abbreviated Journal |
Phys Chem Chem Phys |
|
Volume |
13 |
Issue |
10 |
Pages |
4318-4325 |
|
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
Abstract |
Synchrotron small angle X-ray scattering (SAXS) was used to characterize silicalite-1 zeolite crystallization from TEOS/TPAOH/water clear sol. SAXS patterns were recorded over a broad range of length scales, enabling the simultaneous monitoring of nanoparticles and crystals occurring at various stages of the synthesis. A simple two-population model accurately described the patterns. Nanoparticles were modeled by polydisperse coreshell spheres and crystals by monodisperse oblate ellipsoids. These models were consistent with TEM images. The SAXS results, in conjunction with in situ light scattering, showed that nucleation of crystals occurred in a short period of time. Crystals were uniform in size and shape and became increasingly anisotropic during growth. In the presence of nanoparticles, crystal growth was fast. During crystal growth, the number of nanoparticles decreased gradually but their size was constant. These observations suggested that the nanoparticles were growth units in an aggregative crystal growth mechanism. Crystals grown in the presence of nanoparticles developed a faceted habit and intergrowths. In the final stages of growth, nanoparticles were depleted. Concurrently, the crystal growth rate decreased significantly. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
Cambridge |
Editor |
|
|
Language |
|
Wos |
000287584700017 |
Publication Date |
2011-01-24 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
1463-9076;1463-9084; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
4.123 |
Times cited |
22 |
Open Access |
|
|
Notes |
Fwo; Iap; Esteem 026019 |
Approved |
Most recent IF: 4.123; 2011 IF: 3.573 |
|
Call Number |
UA @ lucian @ c:irua:87602 |
Serial |
2155 |
Permanent link to this record |
|
|
|
|
Author |
Groat, L.A.; Kek, S.; Bismayer, U.; Schmidt, C.; Krane, H.G.; Meyer, H.; Nistor, L.; Van Tendeloo, G. |
|
Title |
A synchrotron radiation, HRTEM, X-ray powder diffraction, and Raman spectroscopic study of malayaite, CaSnSiO5 |
Type |
A1 Journal article |
|
Year |
1996 |
Publication |
The American mineralogist |
Abbreviated Journal |
Am Mineral |
|
Volume |
81 |
Issue |
5/6 |
Pages |
595-602 |
|
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
Abstract |
Synchrotron radiation, high-resolution transmission electron microscopy (HRTEM), X-ray powder diffraction, and Raman spectroscopy were used to study the structure and thermal behavior of malayaite, CaSnSiO5. No indications of deviation from A2/a symmetry and no structural transitions were observed between 100 and 870 K. HRTEM revealed that the material is free of domains and antiphase boundaries. However, the lattice constants, cell volume, and Raman-active phonons show a thermal discontinuity near 500 K, which is possibly related to variation of the coordination sphere around the highly anisotropic Ca position. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
Washington, D.C. |
Editor |
|
|
Language |
|
Wos |
A1996UP41100006 |
Publication Date |
0000-00-00 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
0003-004x |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
1.964 |
Times cited |
19 |
Open Access |
|
|
Notes |
|
Approved |
no |
|
Call Number |
UA @ lucian @ c:irua:16862 |
Serial |
3407 |
Permanent link to this record |
|
|
|
|
Author |
Vast, L.; Carpentier, L.; Lallemand, F.; Colomer, J.-F.; Van Tendeloo, G.; Fonseca, A.; Nagy, J.B.; Mekhalif, Z.; Delhalle, J. |
|
Title |
Multiwalled carbon nanotubes functionalized with 7-octenyltrichlorosilane and n-octyltrichlorosilane: dispersion in Sylgard®184 silicone and Youngs modulus |
Type |
A1 Journal article |
|
Year |
2009 |
Publication |
Journal of materials science |
Abbreviated Journal |
J Mater Sci |
|
Volume |
44 |
Issue |
13 |
Pages |
3476-3482 |
|
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
Abstract |
Sylgard®184/multiwalled carbon nanotube (MWNT) composites have been prepared by in situ polymerization using purified and functionalized multiwalled carbon nanotubes (f-MWNTs) as fillers. Surface modification of the MWNTs has been carried out by silanization with 7-octenyltrichlorosilane (7OTCS) and n-octyltrichlorosilane (nOTCS). The modification and dispersion of the carbon nanotubes in composites were characterized by X-ray photoelectron spectroscopy (XPS), transmission electron spectroscopy (TEM), and high-resolution transmission electron spectroscopy (HRTEM). Youngs modulus results were derived from indentation testing. It is shown that the terminal-vinyl group of 7OTCS molecules plays an essential role for both the dispersion of the f-MWNTs in the composite and its mechanical properties. At loading as low as 0.2 wt%, the Youngs modulus is shown to increase up to 50%. This is interpreted as resulting from a combination of the good compatibility in the forming silicone matrix of the MWNTs coated with a siloxane network, on the one hand, and the covalent links created between the terminal-vinyl groups and the host matrix in formation, on the other hand. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
London |
Editor |
|
|
Language |
|
Wos |
000267153200022 |
Publication Date |
2009-04-20 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
0022-2461;1573-4803; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
2.599 |
Times cited |
16 |
Open Access |
|
|
Notes |
Iuap |
Approved |
Most recent IF: 2.599; 2009 IF: 1.471 |
|
Call Number |
UA @ lucian @ c:irua:77844 |
Serial |
2245 |
Permanent link to this record |
|
|
|
|
Author |
Bekermann, D.; Gasparotto, A.; Barreca, D.; Devi, A.; Fischer, R.A.; Kete, M.; Štangar, U.L.; Lebedev, O.I.; Maccato, C.; Tondello, E.; Van Tendeloo, G. |
|
Title |
ZnO nanorod arrays by plasma-enhanced CVD for light-activated functional applications |
Type |
A1 Journal article |
|
Year |
2010 |
Publication |
ChemPhysChem : a European journal of chemical physics and physical chemistry |
Abbreviated Journal |
Chemphyschem |
|
Volume |
11 |
Issue |
11 |
Pages |
2337-2340 |
|
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
Abstract |
Switch of the surface properties: Supported ZnO nanorod arrays with tailored roughness and aspect ratios are successfully synthesized by plasma-enhanced chemical vapor deposition. Such nanostructures exhibit significant superhydrophilic and photocatalytic properties tunable as a function of their morphological organization (see picture). This renders them promising building blocks for the fabrication of stimuli-responsive materials. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
Weinheim |
Editor |
|
|
Language |
|
Wos |
000281061500008 |
Publication Date |
2010-06-16 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
1439-4235;1439-7641; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
3.075 |
Times cited |
38 |
Open Access |
|
|
Notes |
Esteem 026019 |
Approved |
Most recent IF: 3.075; 2010 IF: 3.340 |
|
Call Number |
UA @ lucian @ c:irua:84594 |
Serial |
3935 |
Permanent link to this record |
|
|
|
|
Author |
González-Rubio, G.; Mosquera, J.; Kumar, V.; Pedrazo-Tardajos, A.; Llombart, P.; Solís, D.M.; Lobato, I.; Noya, E.G.; Guerrero-Martínez, A.; Taboada, J.M.; Obelleiro, F.; MacDowell, L.G.; Bals, S.; Liz-Marzán, L.M. |
|
Title |
Micelle-directed chiral seeded growth on anisotropic gold nanocrystals |
Type |
A1 Journal article |
|
Year |
2020 |
Publication |
Science |
Abbreviated Journal |
Science |
|
Volume |
368 |
Issue |
368 |
Pages |
1472-1477 |
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
|
Abstract |
Surfactant-assisted seeded growth of metal nanoparticles (NPs) can be engineered to produce anisotropic gold nanocrystals with high chiroptical activity through the templating effect of chiral micelles formed in the presence of dissymmetric cosurfactants. Mixed micelles adsorb on gold nanorods, forming quasihelical patterns that direct seeded growth into NPs with pronounced morphological and optical handedness. Sharp chiral wrinkles lead to chiral plasmon modes with high dissymmetry factors (~0.20). Through variation of the dimensions of chiral wrinkles, the chiroptical properties can be tuned within the visible and near-infrared electromagnetic spectrum. The micelle-directed mechanism allows extension to other systems, such as the seeded growth of chiral platinum shells on gold nanorods. This approach provides a reproducible, simple, and scalable method toward the fabrication of NPs with high chiral optical activity. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
Language |
|
Wos |
000545264600040 |
Publication Date |
2020-06-26 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
0036-8075 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
56.9 |
Times cited |
187 |
Open Access |
OpenAccess |
|
Notes |
L.M.L.-M. acknowledges funding from the European Research Council (ERC AdG No. 787510). G.G.-R. and J.M. thanks the Spanish MICIU for FPI (BES-2014-068972) and Juan de la Cierva-fellowships (FJCI-2015-25080). S.B., L.M.L.-M., V.K, and A.P.- T. acknowledge financial support from the European Commission under the Horizon 2020 Programme by means of the grant agreement No. 731019 (EUSMI) and the ERC Consolidator Grant No. 815128 (REALNANO). J.M.T and F.O acknowledge financial support from the Spanish MICIU (Grants TEC2017-85376-C2-1-R, TEC2017-85376-C2-2-R), as well as from the ERDF and the Galician Regional Government as part of the agreement for funding the Atlantic Research Center for Information and Communication Technologies (AtlantTIC). AG-M acknowledges financial support from the Spanish MICIU (Grant RTI2018-095844-BI00), EGN and LGM acknowledge funds from the Spanish MICIU (Grant No. FIS2017- 89361-C3-2-P), as well as the use of the Mare-Nostrum supercomputer and the technical support provided by Barcelona Supercomputing Center from the Spanish Network of Supercomputing (Grants QCM-2018-3-0039 and QCM-2019-1-0038). This work was performed under the Maria de Maeztu Units of Excellence Program from the Spanish State 13 Research Agency – Grant No. MDM-2017-0720.; sygma |
Approved |
Most recent IF: 56.9; 2020 IF: 37.205 |
|
Call Number |
EMAT @ emat @c:irua:170137 |
Serial |
6391 |
Permanent link to this record |
|
|
|
|
Author |
Turner, S.; Lazar, S.; Freitag, B.; Egoavil, R.; Verbeeck, J.; Put, S.; Strauven, Y.; Van Tendeloo, G. |
|
Title |
High resolution mapping of surface reduction in ceria nanoparticles |
Type |
A1 Journal article |
|
Year |
2011 |
Publication |
Nanoscale |
Abbreviated Journal |
Nanoscale |
|
Volume |
3 |
Issue |
8 |
Pages |
3385-3390 |
|
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
Abstract |
Surface reduction of ceria nano octahedra with predominant {111} and {100} type surfaces is studied using a combination of aberration-corrected Transmission Electron Microscopy (TEM) and spatially resolved electron energy-loss spectroscopy (EELS) at high energy resolution and atomic spatial resolution. The valency of cerium ions at the surface of the nanoparticles is mapped using the fine structure of the Ce M4,5 edge as a fingerprint. The valency of the surface cerium ions is found to change from 4+ to 3+ owing to oxygen deficiency (vacancies) close to the surface. The thickness of this Ce3+ shell is measured using atomic-resolution Scanning Transmission Electron Microscopy (STEM)-EELS mapping over a {111} surface (the predominant facet for this ceria morphology), {111} type surface island steps and {100} terminating planes. For the {111} facets and for {111} surface islands, the reduction shell is found to extend over a single fully reduced surface plane and 12 underlying mixed valency planes. For the {100} facets the reduction shell extends over a larger area of 56 oxygen vacancy-rich planes. This finding provides a plausible explanation for the higher catalytic activity of the {100} surface facets in ceria. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
Cambridge |
Editor |
|
|
Language |
|
Wos |
000293521700057 |
Publication Date |
2011-06-30 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
2040-3364;2040-3372; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
7.367 |
Times cited |
127 |
Open Access |
|
|
Notes |
Fwo |
Approved |
Most recent IF: 7.367; 2011 IF: 5.914 |
|
Call Number |
UA @ lucian @ c:irua:90361UA @ admin @ c:irua:90361 |
Serial |
1458 |
Permanent link to this record |
|
|
|
|
Author |
Goris, B.; Guzzinati, G.; Fernández-López, C.; Pérez-Juste, J.; Liz-Marzán, L.M.; Trügler, A.; Hohenester, U.; Verbeeck, J.; Bals, S.; Van Tendeloo, G. |
|
Title |
Plasmon mapping in Au@Ag nanocube assemblies |
Type |
A1 Journal article |
|
Year |
2014 |
Publication |
The journal of physical chemistry: C : nanomaterials and interfaces |
Abbreviated Journal |
J Phys Chem C |
|
Volume |
118 |
Issue |
28 |
Pages |
15356-15362 |
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
|
Abstract |
Surface plasmon modes in metallic nanostructures largely determine their optoelectronic properties. Such plasmon modes can be manipulated by changing the morphology of the nanoparticles or by bringing plasmonic nanoparticle building blocks close to each other within organized assemblies. We report the EELS mapping of such plasmon modes in pure Ag nanocubes, Au@Ag coreshell nanocubes, and arrays of Au@Ag nanocubes. We show that these arrays enable the creation of interesting plasmonic structures starting from elementary building blocks. Special attention will be dedicated to the plasmon modes in a triangular array formed by three nanocubes. Because of hybridization, a combination of such nanotriangles is shown to provide an antenna effect, resulting in strong electrical field enhancement at the narrow gap between the nanotriangles. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
Washington, D.C. |
Editor |
|
|
Language |
|
Wos |
000339368700031 |
Publication Date |
2014-06-27 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
1932-7447;1932-7455; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
4.536 |
Times cited |
41 |
Open Access |
OpenAccess |
|
Notes |
Fwo; 246791 Countatoms; 278510 Vortex; 335078 Colouratom; 262348 Esmi ECASJO;; ECASSara; (ROMEO:white; preprint:; postprint:restricted 12 months embargo; pdfversion:cannot); |
Approved |
Most recent IF: 4.536; 2014 IF: 4.772 |
|
Call Number |
UA @ lucian @ c:irua:118099UA @ admin @ c:irua:118099 |
Serial |
2644 |
Permanent link to this record |
|
|
|
|
Author |
Herzog, M.J.; Gauquelin, N.; Esken, D.; Verbeeck, J.; Janek, J. |
|
Title |
Facile dry coating method of high-nickel cathode material by nanostructured fumed alumina (Al2O3) improving the performance of lithium-ion batteries |
Type |
A1 Journal article |
|
Year |
2021 |
Publication |
Energy technology |
Abbreviated Journal |
|
|
Volume |
9 |
Issue |
4 |
Pages |
2100028 |
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
|
Abstract |
Surface coating is a crucial method to mitigate the aging problem of high-Ni cathode active materials (CAMs). By avoiding the direct contact of the CAM and the electrolyte, side reactions are hindered. Commonly used techniques like wet or ALD coating are time consuming and costly. Therefore, a more cost-effective coating technique is desirable. Herein, a facile and fast dry powder coating process for CAMs with nanostructured fumed metal oxides are reported. As the model case, the coating of high-Ni NMC (LiNi0.7Mn0.15Co0.15O2) by nanostructured fumed Al2O3 is investigated. A high coverage of the CAM surface with an almost continuous coating layer is achieved, still showing some porosity. Electrochemical evaluation shows a significant increase in capacity retention, cycle life and rate performance of the coated NMC material. The coating layer protects the surface of the CAM successfully and prevents side reactions, resulting in reduced solid electrolyte interface (SEI) formation and charge transfer impedance during cycling. A mechanism on how the coating layer enhances the cycling performance is hypothesized. The stable coating layer effectively prevents crack formation and particle disintegration of the NMC. In depth analysis indicates partial formation of LixAl2O3/LiAlO2 in the coating layer during cycling, enhancing lithium ion diffusivity and thus, also the rate performance. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
Language |
|
Wos |
000621000700001 |
Publication Date |
2021-01-23 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
2194-4296; 2194-4288 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
|
Times cited |
25 |
Open Access |
OpenAccess |
|
Notes |
The authors would like to thank Erik Peldszus and Steve Rienecker for the support with scanning electron microscopy and X-ray photoelectron spectroscopy analysis. The Qu-Ant-EM microscope and the direct electron detector were partly funded by the Hercules fund from the Flemish Government. N.G. and J.V. acknowledge funding from GOA project “Solarpaint” of the University of Antwerp. Funding from the Flemish Research Fund (FWO) project G0F1320N is acknowledged.; Open access funding enabled and organized by Projekt DEAL. |
Approved |
Most recent IF: NA |
|
Call Number |
UA @ admin @ c:irua:176670 |
Serial |
6724 |
Permanent link to this record |
|
|
|
|
Author |
Wang, Y.; Belén Serrano, A.; Sentosun, K.; Bals, S.; Liz-Marzán, L.M. |
|
Title |
Stabilization and encapsulation of gold nanostars mediated by dithiols |
Type |
A1 Journal article |
|
Year |
2015 |
Publication |
Small |
Abbreviated Journal |
Small |
|
Volume |
11 |
Issue |
11 |
Pages |
4314-4320 |
|
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
Abstract |
Surface chemistry plays a pivotal role in regulating the morphology of nanoparticles, maintaining colloidal stability, and mediating the interaction with target analytes toward practical applications such as surface-enhanced Raman scattering (SERS)-based sensing and imaging. The use of a binary ligand mixture composed of 1,4-benzenedithiol (BDT) and hexadecyltrimethylammonium chloride (CTAC) to provide gold nanostars with long-term stability is reported. This is despite BDT being a bifunctional ligand, which usually leads to bridging and loss of colloidal stability. It is found however that neither BDT nor CTAC alone are able to provide sufficient colloidal and chemical stability. BDT-coated Au nanostars are additionally used as seeds to direct the encapsulation with a gold outer shell, leading to the formation of unusual nanostructures including semishell-coated gold nanostars, which are characterized by high-resolution electron microscopy and electron tomography. Finally, BDT is exploited as a probe to reveal the enhanced local electric fields in the different nanostructures, showing that the semishell configuration provides significantly high SERS signals as compared to other coreshell configurations obtained during seeded growth, including full shells. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
Weinheim |
Editor |
|
|
Language |
|
Wos |
000360852900009 |
Publication Date |
2015-06-02 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
1613-6810; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
8.643 |
Times cited |
36 |
Open Access |
OpenAccess |
|
Notes |
267867 Plasmaquo; 335078 Colouratom; 262348 Esmi; ECAS_Sara; (ROMEO:yellow; preprint:; postprint:restricted ; pdfversion:cannot); |
Approved |
Most recent IF: 8.643; 2015 IF: 8.368 |
|
Call Number |
c:irua:127571 |
Serial |
3136 |
Permanent link to this record |
|
|
|
|
Author |
Wang, Y.; Sentosun, K.; Li, A.; Coronado-Puchau, M.; Sánchez-Iglesias, A.; Li, S.; Su, X.; Bals, S.; Liz-Marzán, L.M. |
|
Title |
Engineering Structural Diversity in Gold Nanocrystals by Ligand-Mediated Interface Control |
Type |
A1 Journal article |
|
Year |
2015 |
Publication |
Chemistry of materials |
Abbreviated Journal |
Chem Mater |
|
Volume |
27 |
Issue |
27 |
Pages |
8032-8040 |
|
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
Abstract |
Surface and interface control is fundamentally important for crystal growth engineering, catalysis, surface enhanced spectroscopies, and self-assembly, among other processes and applications. Understanding the role of ligands in regulating surface properties of plasmonic metal nanocrystals during growth has received considerable attention. However, the underlying mechanisms and the diverse functionalities of ligands are yet to be fully addressed. In this contribution,
we report a systematic study of ligand-mediated interface control in seeded growth of gold nanocrystals, leading to diverse and exotic nanostructures with an improved surface enhanced Raman scattering (SERS) activity. Three dimensional transmission electron microscopy (3D TEM) revealed an intriguing gold shell growth process mediated by the bifunctional ligand 1,4-benzenedithiol (BDT), which leads to a unique crystal growth mechanism as compared to other ligands, and subsequently to the concept of interfacial energy control mechanism. Volmer-Weber growth mode was proposed to be responsible for BDT-mediated seeded growth, favoring the strongest interfacial energy and generating an asymmetric island growth pathway with internal crevices/gaps. This additionally favors incorporation of BDT at the plasmonic nanogaps, thereby generating strong SERS activity with a maximum efficiency for a core-semishell configuration obtained along seeded growth. Numerical modeling was used to explain this observation. Interestingly, the same strategy can be used to engineer the structural diversity of this system, by using gold nanoparticle seeds with various sizes and shapes, and varying the [Au3+]/[Au0] ratio. This rendered a series of diverse and exotic plasmonic nanohybrids such as semishell-coated gold nanorods, with embedded Raman-active tags and Janus surface with distinct surface functionalities.
These would greatly enrich the plasmonic nanostructure toolbox for various studies and applications such as anisotropic nanocrystal engineering, SERS, and high-resolution Raman bioimaging or nanoantenna devices. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
Language |
|
Wos |
000366223200023 |
Publication Date |
2015-10-09 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
0897-4756;1520-5002; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
9.466 |
Times cited |
18 |
Open Access |
OpenAccess |
|
Notes |
The authors thank Bart Goris for his help with electron tomography. This work was funded by the European Commission (Grant #310445-2, SAVVY). The authors acknowledge financial support from European Research Council (ERC Advanced Grant # 267867- PLASMAQUO, ERC Starting Grant #335078-COLOURATOMS). The authors also appreciate financial support from the European Union under the Seventh Framework Program (Integrated Infrastructure Initiative N. 262348 European Soft Matter Infrastructure, ESMI). Wang Y. and Su X. would like to acknowledge the Agency for Science, Technology and Research (A*STAR), Singapore, for the financial support under the Grant JCO 14302FG096. M. C.-P. acknowledges an FPU scholarship from the Spanish Ministry of Education, Culture and Sports.; ECAS_Sara; (ROMEO:white; preprint:; postprint:restricted 12 months embargo; pdfversion:cannot); |
Approved |
Most recent IF: 9.466; 2015 IF: 8.354 |
|
Call Number |
c:irua:129598 c:irua:129598 |
Serial |
3972 |
Permanent link to this record |
|
|
|
|
Author |
Voorhaar, L.; Diaz, M.M.; Leroux, F.; Rogers, S.; Abakumov, A.M.; Van Tendeloo, G.; Van Assche, G.; Van Mele, B.; Hoogenboom, R. |
|
Title |
Supramolecular thermoplastics and thermoplastic elastomer materials with self-healing ability based on oligomeric charged triblock copolymers |
Type |
A1 Journal article |
|
Year |
2017 |
Publication |
NPG Asia materials |
Abbreviated Journal |
Npg Asia Mater |
|
Volume |
9 |
Issue |
|
Pages |
e385 |
|
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
Abstract |
Supramolecular polymeric materials constitute a unique class of materials held together by non-covalent interactions. These dynamic supramolecular interactions can provide unique properties such as a strong decrease in viscosity upon relatively mild heating, as well as self-healing ability. In this study we demonstrate the unique mechanical properties of phase-separated electrostatic supramolecular materials based on mixing of low molar mass, oligomeric, ABA-triblock copolyacrylates with oppositely charged outer blocks. In case of well-chosen mixtures and block lengths, the charged blocks are phase separated from the uncharged matrix in a hexagonally packed nanomorphology as observed by transmission electron microscopy. Thermal and mechanical analysis of the material shows that the charged sections have a T-g closely beyond room temperature, whereas the material shows an elastic response at temperatures far above this T-g ascribed to the electrostatic supramolecular interactions. A broad set of materials having systematic variations in triblock copolymer structures was used to provide insights in the mechanical properties and and self-healing ability in correlation with the nanomorphology of the materials. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
Language |
|
Wos |
000402065300005 |
Publication Date |
2017-05-26 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
1884-4049; 1884-4057 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
9.157 |
Times cited |
8 |
Open Access |
OpenAccess |
|
Notes |
; This research was conducted in the framework of the SIM-SHE/NAPROM project and SIM is gratefully acknowledged for the financial support. ; |
Approved |
Most recent IF: 9.157 |
|
Call Number |
UA @ lucian @ c:irua:144263 |
Serial |
4691 |
Permanent link to this record |
|
|
|
|
Author |
Barreca, D.; Gri, F.; Gasparotto, A.; Carraro, G.; Bigiani, L.; Altantzis, T.; Žener, B.; Lavrenčič Štangar, U.; Alessi, B.; Padmanaban, D.B.; Mariotti, D.; Maccato, C. |
|
Title |
Multi-functional MnO2nanomaterials for photo-activated applications by a plasma-assisted fabrication route |
Type |
A1 Journal article |
|
Year |
2019 |
Publication |
Nanoscale |
Abbreviated Journal |
Nanoscale |
|
Volume |
11 |
Issue |
1 |
Pages |
98-108 |
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
|
Abstract |
Supported MnO2-based nanomaterials were fabricated on fluorine-doped tin oxide substrates by plasma enhanced-chemical vapor deposition (PE-CVD) between 100 °C and 400 °C, starting from a fluorinated Mn(II) diamine diketonate precursor. Growth experiments yielded -MnO2 nanosystems with hierarchical morphology tuneable from dendritic structures to quasi-1D nanosystems as a function of growth temperature, whose variation enabled also a concomitant tailoring of the system fluorine content, and of the optical absorption and band gap. Preliminary photocatalytic tests were aimed at the investigation of photoinduced hydrophilic (PH) and solid phase photocatalytic (PC) performances of the present nanomaterials, as well as at the photodegradation of Plasmocorinth B azo-dye aqueous solutions. The obtained findings highlighted an attractive system photoactivity even under visible light, finely tailored by fluorine content, morphological organization and optical properties of the prepared nanostructures. The results indicate that the synthesized MnO2 nanosystems have potential applications as advanced smart materials for anti-fogging/self-cleaning end uses and water purification. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
Language |
|
Wos |
000454327500037 |
Publication Date |
2018-10-10 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
2040-3364 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
7.367 |
Times cited |
7 |
Open Access |
OpenAccess |
|
Notes |
Padova University DOR 2016–2017, P-DiSC #03BIRD2016-UNIPD projects, HERALD Cost Action MP1402 – 37831 and ACTION post-doc fellowship are acknowledged for financial support. T.A. acknowledges a post-doctoral grant from the Research Foundation Flanders (FWO). Thanks are also due to Prof. Sara Bals (EMAT, University of Antwerp, Belgium), Prof. Romana Cerc Korošec and to Dr. Lev Matoh (University of Ljubljana, Slovenia), and to Prof. Elza Bontempi (Brescia University, Italy). The work was also supported by EPSRC (award EP/R008841/1, EP/M024938/1). |
Approved |
Most recent IF: 7.367 |
|
Call Number |
EMAT @ emat @UA @ admin @ c:irua:156388 |
Serial |
5148 |
Permanent link to this record |
|
|
|
|
Author |
Barreca, D.; Carraro, G.; Warwick, M.E.A.; Kaunisto, K.; Gasparotto, A.; Gombac, V.; Sada, C.; Turner, S.; Van Tendeloo, G.; Maccato, C.; Fornasiero, P.; |
|
Title |
Fe2O3-TiO2 nanosystems by a hybrid PE-CVD/ALD approach : controllable synthesis, growth mechanism, and photocatalytic properties |
Type |
A1 Journal article |
|
Year |
2015 |
Publication |
CrystEngComm |
Abbreviated Journal |
Crystengcomm |
|
Volume |
17 |
Issue |
17 |
Pages |
6219-6226 |
|
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
Abstract |
Supported Fe2O3–TiO2 nanocomposites are fabricated by an original vapor phase synthetic strategy, consisting of the initial growth of Fe2O3 nanosystems on fluorine-doped tin oxide substrates by plasma enhanced-chemical vapor deposition, followed by atomic layer deposition of TiO2 overlayers with variable thickness, and final thermal treatment in air. A thorough characterization of the target systems is carried out by X-ray diffraction, atomic force microscopy, field emission-scanning electron microscopy, energy dispersive X-ray spectroscopy, transmission electron microscopy, and X-ray photoelectron spectroscopy. High purity nanomaterials characterized by the co-presence of Fe2O3 (hematite) and TiO2 (anatase), with an intimate Fe2O3–TiO2 contact, are successfully obtained. In addition, photocatalytic tests demonstrate that, whereas both single-phase oxides do not show appreciable activity, the composite systems are able to degrade methyl orange aqueous solutions under simulated solar light, and even visible light, with an efficiency directly dependent on TiO2 overlayer thickness. This finding opens attractive perspectives for eventual applications in wastewater treatment. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
Language |
|
Wos |
000358915300018 |
Publication Date |
2015-07-23 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
1466-8033; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
3.474 |
Times cited |
25 |
Open Access |
|
|
Notes |
The research leading to these results has received funding from the FP7 project “SOLAROGENIX” IJNMP4-SL-2012- 310333), as well as from Padova University ex-60% 2012–2015 projects, grant no. CPDR132937/13 (SOLLEONE), and Regione Lombardia-INSTM ATLANTE projects. S. T. acknowledges the FWO Flanders for a post-doctoral scholarship. Thanks are also due to Prof. S. Mathur and Dr. Y. Gönüllü (Department of Chemistry, Cologne University, Germany) for their precious help and assistance in ALD depositions, and to Prof. E. Bontempi (Chemistry for Technologies Laboratory, Brescia University, Italy) for XRD analyses. |
Approved |
Most recent IF: 3.474; 2015 IF: 4.034 |
|
Call Number |
c:irua:127237 |
Serial |
3531 |
Permanent link to this record |
|
|
|
|
Author |
Verbruggen, S.W.; Deng, S.; Kurttepeli, M.; Cott, D.J.; Vereecken, P.M.; Bals, S.; Martens, J.A.; Detavernier, C.; Lenaerts, S. |
|
Title |
Photocatalytic acetaldehyde oxidation in air using spacious TiO2 films prepared by atomic layer deposition on supported carbonaceous sacrificial templates |
Type |
A1 Journal article |
|
Year |
2014 |
Publication |
Applied catalysis : B : environmental |
Abbreviated Journal |
Appl Catal B-Environ |
|
Volume |
160 |
Issue |
|
Pages |
204-210 |
|
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT); Sustainable Energy, Air and Water Technology (DuEL) |
|
Abstract |
Supported carbon nanosheets and carbon nanotubes served as sacrificial templates for preparing spacious TiO2 photocatalytic thin films. Amorphous TiO2 was deposited conformally on the carbonaceous template material by atomic layer deposition (ALD). Upon calcination at 550 °C, the carbon template was oxidatively removed and the as-deposited continuous amorphous TiO2 layers transformed into interlinked anatase nanoparticles with an overall morphology commensurate to the original template structure. The effect of type of template, number of ALD cycles and gas residence time of pollutant on the photocatalytic activity, as well as the stability of the photocatalytic performance of these thin films was investigated. The TiO2 films exhibited excellent photocatalytic activity toward photocatalytic degradation of acetaldehyde in air as a model reaction for photocatalytic indoor air pollution abatement. Optimized films outperformed a reference film of commercial PC500. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
Amsterdam |
Editor |
|
|
Language |
|
Wos |
000340687900024 |
Publication Date |
2014-05-27 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
0926-3373; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
9.446 |
Times cited |
37 |
Open Access |
OpenAccess |
|
Notes |
335078 Colouratom; Iap-Pai P7/05; Fwo; ECAS_Sara; (ROMEO:green; preprint:; postprint:can ; pdfversion:cannot); |
Approved |
Most recent IF: 9.446; 2014 IF: 7.435 |
|
Call Number |
UA @ lucian @ c:irua:117094 |
Serial |
2608 |
Permanent link to this record |
|
|
|
|
Author |
Grünewald, L.; Chezganov, D.; De Meyer, R.; Orekhov, A.; Van Aert, S.; Bogaerts, A.; Bals, S.; Verbeeck, J. |
|
Title |
Supplementary Information for “In-situ Plasma Studies using a Direct Current Microplasma in a Scanning Electron Microscope” |
Type |
Dataset |
|
Year |
2023 |
Publication |
|
Abbreviated Journal |
|
|
Volume |
|
Issue |
|
Pages |
|
|
Keywords |
Dataset; Engineering sciences. Technology; Electron microscopy for materials research (EMAT); Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) |
|
Abstract |
Supplementary information for the article “In-situ Plasma Studies using a Direct Current Microplasma in a Scanning Electron Microscope” containing the videos of in-situ SEM imaging (mp4 files), raw data/images, and Jupyter notebooks (ipynb files) for data treatment and plots. Link to the preprint: https://doi.org/10.48550/arXiv.2308.15123 Explanation of the data files can be found in the Information.pdf file. The Videos folder contains the in-situ SEM image series mentioned in the paper. If there are any questions/bugs, feel free to contact me at lukas.grunewaldatuantwerpen.be |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
Language |
|
Wos |
|
Publication Date |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
|
ISBN |
|
Additional Links |
UA library record |
|
Impact Factor |
|
Times cited |
|
Open Access |
Not_Open_Access |
|
Notes |
|
Approved |
Most recent IF: NA |
|
Call Number |
UA @ admin @ c:irua:203389 |
Serial |
9100 |
Permanent link to this record |
|
|
|
|
Author |
Johnson, G.; Yang, M.Y.; Liu, C.; Zhou, H.; Zuo, X.; Dickie, D.A.; Wang, S.; Gao, W.; Anaclet, B.; Perras, F.A.; Ma, F.; Zeng, C.; Wang, D.; Bals, S.; Dai, S.; Xu, Z.; Liu, G.; Goddard III, W.A.; Zhang, S. |
|
Title |
Nanocluster superstructures assembled via surface ligand switching at high temperature |
Type |
A1 Journal article |
|
Year |
2023 |
Publication |
Nature synthesis |
Abbreviated Journal |
|
|
Volume |
2 |
Issue |
9 |
Pages |
828-837 |
|
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
Abstract |
Superstructures with nanoscale building blocks, when coupled with precise control of the constituent units, open opportunities in rationally designing and manufacturing desired functional materials. Yet, synthetic strategies for the large-scale production of superstructures are scarce. We report a scalable and generalized approach to synthesizing superstructures assembled from atomically precise Ce24O28(OH)8 and other rare-earth metal-oxide nanoclusters alongside a detailed description of the self-assembly mechanism. Combining operando small-angle X-ray scattering, ex situ molecular and structural characterizations, and molecular dynamics simulations indicates that a high-temperature ligand-switching mechanism, from oleate to benzoate, governs the formation of the nanocluster assembly. The chemical tuning of surface ligands controls superstructure disassembly and reassembly, and furthermore, enables the synthesis of multicomponent superstructures. This synthetic approach, and the accurate mechanistic understanding, are promising for the preparation of superstructures for use in electronics, plasmonics, magnetics and catalysis. Synthesizing superstructures with precisely controlled nanoscale building blocks is challenging. Here the assembly of superstructures is reported from atomically precise Ce24O28(OH)8 and other rare-earth metal-oxide nanoclusters and their multicomponent combinations. A high-temperature ligand-switching mechanism controls the self-assembly. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
Language |
|
Wos |
001124824000001 |
Publication Date |
2023-05-01 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
|
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
|
Times cited |
2 |
Open Access |
Not_Open_Access |
|
Notes |
|
Approved |
Most recent IF: NA |
|
Call Number |
UA @ admin @ c:irua:202180 |
Serial |
9060 |
Permanent link to this record |
|
|
|
|
Author |
Semkina, A.; Abakumov, M.; Grinenko, N.; Abakumov, A.; Skorikov, A.; Mironova, E.; Davydova, G.; Majouga, A.G.; Nukolova, N.; Kabanov, A.; Chekhonin, V.; |
|
Title |
Core-shell-corona doxorubicin-loaded superparamagnetic Fe3O4 nanoparticles for cancer theranostics |
Type |
A1 Journal article |
|
Year |
2015 |
Publication |
Colloids and surfaces: B : biointerfaces |
Abbreviated Journal |
Colloid Surface B |
|
Volume |
136 |
Issue |
136 |
Pages |
1073-1080 |
|
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
Abstract |
Superparamagnetic iron oxide magnetic nanoparticles (MNPs) are successfully used as contrast agents in magnetic-resonance imaging. They can be easily functionalized for drug delivery functions, demonstrating great potential for both imaging and therapeutic applications. Here we developed new pH-responsive theranostic core-shell-corona nanoparticles consisting of superparamagentic Fe3O4 core that displays high T2 relaxivity, bovine serum albumin (BSA) shell that binds anticancer drug, doxorubicin (Dox) and poly(ethylene glycol) (PEG) corona that increases stability and biocompatibility. The nanoparticles were produced by adsorption of the BSA shell onto the Fe3O4 core followed by crosslinking of the protein layer and subsequent grafting of the PEG corona using monoamino-terminated PEG via carbodiimide chemistry. The hydrodynamic diameter, zeta-potential, composition and T2 relaxivity of the resulting nanoparticles were characterized using transmission electron microscopy, dynamic light scattering, thermogravimetric analysis and T2-relaxometry. Nanoparticles were shown to absorb Dox molecules, possibly through a combination of electrostatic and hydrophobic interactions. The loading capacity (LC) of the nanoparticles was 8 wt.%. The Dox loaded nanoparticles release the drug at a higher rate at pH 5.5 compared to pH 7.4 and display similar cytotoxicity against C6 and HEK293 cells as the free Dox. (C) 2015 Elsevier B.V. All rights reserved. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
Amsterdam |
Editor |
|
|
Language |
|
Wos |
000367408100131 |
Publication Date |
2015-11-10 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
0927-7765 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
3.887 |
Times cited |
37 |
Open Access |
|
|
Notes |
|
Approved |
Most recent IF: 3.887; 2015 IF: 4.152 |
|
Call Number |
UA @ lucian @ c:irua:131075 |
Serial |
4157 |
Permanent link to this record |
|
|
|
|
Author |
Delville, R.; Malard, B.; Pilch, J.; Sittner, P.; Schryvers, D. |
|
Title |
Transmission electron microscopy investigation of dislocation slip during superelastic cycling of NiTi wires |
Type |
A1 Journal article |
|
Year |
2011 |
Publication |
International journal of plasticity |
Abbreviated Journal |
Int J Plasticity |
|
Volume |
27 |
Issue |
2 |
Pages |
282-297 |
|
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
Abstract |
Superelastic deformation of thin NiTi wires containing various nanograined microstructures was investigated by tensile cyclic loading with in situ evaluation of electric resistivity. Defects created by the superelastic cycling in these wires were analyzed by transmission electron microscopy. The role of dislocation slip in superelastic deformation is discussed. NiTi wires having finest microstructures (grain diameter <100 nm) are highly resistant against dislocation slip, while those with fully recrystallized microstructure and grain size exceeding 200 nm are prone to dislocation slip. The density of the observed dislocation defects increases significantly with increasing grain size. The upper plateau stress of the superelastic stressstrain curves is largely grain size independent from 10 up to 1000 nm. It is hence claimed that the HallPetch relationship fails for the stress-induced martensitic transformation in this grain size range. It is proposed that dislocation slip taking place during superelastic cycling is responsible for the accumulated irreversible strains, cyclic instability and degradation of functional properties. No residual martensite phase was found in the microstructures of superelastically cycled wires by TEM and results of the in situ electric resistance measurements during straining also indirectly suggest that none or very little martensite phase remains in the studied cycled superelastic wires after unloading. The accumulation of dislocation defects, however, does not prevent the superelasticity. It only affects the shape of the stressstrain response, makes it unstable upon cycling and changes the deformation mode from localized to homogeneous. The activity of dislocation slip during superelastic deformation of NiTi increases with increasing test temperature and ultimately destroys the superelasticity as the plateau stress approaches the yield stress for slip. Deformation twins in the austenite phase ({1 1 4} compound twins) were frequently found in cycled wires having largest grain size. It is proposed that they formed in the highly deformed B19′ martensite phase during forward loading and are retained in austenite after unloading. Such twinning would represent an additional deformation mechanism of NiTi yielding residual irrecoverable strains. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
Oxford |
Editor |
|
|
Language |
|
Wos |
000284921800007 |
Publication Date |
2010-05-17 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
0749-6419; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
5.702 |
Times cited |
157 |
Open Access |
|
|
Notes |
Fwo; Iap |
Approved |
Most recent IF: 5.702; 2011 IF: 4.603 |
|
Call Number |
UA @ lucian @ c:irua:84651 |
Serial |
3709 |
Permanent link to this record |
|
|
|
|
Author |
Bretos, I.; Schneller, T.; Falter, M.; Baecker, M.; Hollmann, E.; Woerdenweber, R.; Molina-Luna, L.; Van Tendeloo, G.; Eibl, O. |
|
Title |
Solution-derived YBa2Cu3O7-\delta (YBCO) superconducting films with BaZrO3 (BZO) nanodots based on reverse micelle stabilized nanoparticles |
Type |
A1 Journal article |
|
Year |
2015 |
Publication |
Journal of materials chemistry C : materials for optical and electronic devices |
Abbreviated Journal |
J Mater Chem C |
|
Volume |
3 |
Issue |
3 |
Pages |
3971-3979 |
|
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
Abstract |
Superconducting YBa2Cu3O7-delta (YBCO) films with artificial BaZrO3 (BZO) nanodots were prepared using a chemical solution deposition method involving hybrid solutions composed of trifluoroacetate-based YBCO precursors and reverse micelle stabilized BZO nanoparticle dispersions. Microemulsion-mediated synthesis was used to obtain nano-sized (similar to 12 nm) and mono-dispersed BZO nanoparticles that preserve their features once introduced into the YBCO solution, as revealed by dynamic light scattering. Phase pure, epitaxial YBCO films with randomly oriented BZO nanodots distributed over their whole microstructure were grown from the hybrid solutions on (100) LaAlO3 substrates. The morphology of the YBCO-BZO nanocomposite films was strongly influenced by the amount of nanoparticles incorporated into the system, with contents ranging from 5 to 40 mol%. Scanning electron microscopy showed a high density of isolated second-phase defects consisting of BZO nanodots in the nanocomposite film with 10 mol% of BZO. Furthermore, a direct observation and quantitative analysis of lattice defects in the form of interfacial edge dislocations directly induced by the BZO nanodots was evidenced by transmission electron microscopy. The superconducting properties (77 K) of the YBCO films improved considerably by the presence of such nanodots, which seem to enhance the morphology of the sample and therefore the intergranular critical properties. The incorporation of preformed second-phase defects (here, BZO) during the growth of the superconducting phase is the main innovation of this novel approach for the all-solution based low-cost fabrication of long-length coated conductors. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
Language |
|
Wos |
000352870400018 |
Publication Date |
2015-03-06 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
2050-7526; 2050-7534 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
5.256 |
Times cited |
19 |
Open Access |
|
|
Notes |
This work was supported by the German Federal Ministry of Economics and Technology (BMWi) contract no. 0327433A (project ELSA). L. Molina-Luna and G. Van Tendeloo acknowledge funding from the European Research Council (ERC grant no. 24691-COUNTATOMS). The authors gratefully acknowledge J. Dornseiffer for the support with preparation of the microemulsions for the BZO nanoparticles; G. Wasse for the SEM images; and T. Po¨ssinger for the preparation of the artwork. Eurotape |
Approved |
Most recent IF: 5.256; 2015 IF: 4.696 |
|
Call Number |
UA @ lucian @ c:irua:132575 |
Serial |
4245 |
Permanent link to this record |
|
|
|
|
Author |
Ardashnikova, E.I.; Lubarsky, S.V.; Denisenko, D.I.; Shpanchenko, R.V.; Antipov, E.V.; Van Tendeloo, G. |
|
Title |
A new way of synthesis and characterization of superconducting oxyfluoride Sr2Cu(O,F)4+\delta |
Type |
A1 Journal article |
|
Year |
1995 |
Publication |
Physica: C : superconductivity |
Abbreviated Journal |
Physica C |
|
Volume |
253 |
Issue |
3/4 |
Pages |
259-265 |
|
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
Abstract |
Superconducting Cu mixed oxyfluoride, Sr,Cu(O, F)(4+delta), was Obtained via fluorination of Sr2CuO3 by XeF2 in the 100-250 degrees C temperature range in a closed Ni container. The prepared samples exhibited a lower T-c in comparison with earlier reported values. Different samples in the Sr-Cu-O-F system were prepared by a solid-state reaction at 220-400 degrees C, but no formation of the oxyfluoride was detected even with an addition of xenon difluoride. These data allow one to draw conclusions on the metastability of the oxyfluoride under the conditions used, Electron microscopy and X-ray powder diffraction studies revealed large amounts of badly crystallized SrF2; this could be a reason for the small superconducting volume fraction as well as for the inhomogeneous distribution of the anions. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
Amsterdam |
Editor |
|
|
Language |
|
Wos |
A1995TE08400007 |
Publication Date |
0000-00-00 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
0921-4534 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
0.942 |
Times cited |
29 |
Open Access |
|
|
Notes |
|
Approved |
PHYSICS, APPLIED 28/145 Q1 # |
|
Call Number |
UA @ lucian @ c:irua:13322 |
Serial |
2337 |
Permanent link to this record |
|
|
|
|
Author |
Yu, S.; Sankaran, K.J.; Korneychuk, S.; Verbeeck, J.; Haenen, K.; Jiang, X.; Yang, N. |
|
Title |
High-performance supercabatteries using graphite@diamond nano-needle capacitor electrodes and redox electrolytes |
Type |
A1 Journal article |
|
Year |
2019 |
Publication |
Nanoscale |
Abbreviated Journal |
Nanoscale |
|
Volume |
11 |
Issue |
38 |
Pages |
17939-17946 |
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
|
Abstract |
Supercabatteries have the characteristics of supercapacitors and batteries, namely high power and energy densities as well as long cycle life. To construct them, capacitor electrodes with wide potential windows and/or redox electrolytes are required. Herein, graphite@diamond nano-needles and an aqueous solution of Fe(CN)(6)(3-/4-) are utilized as the capacitor electrode and the electrolyte, respectively. This diamond capacitor electrode has a nitrogen-doped diamond core and a nano-graphitic shell. In 0.05 M Fe(CN)(6)(3-/4-) + 1.0 M Na2SO4 aqueous solution, the fabricated supercabattery has a capacitance of 66.65 mF cm(-2) at a scan rate of 10 mV s(-1). It is stable over 10 000 charge/discharge cycles. The symmetric supercabattery device assembled using a two-electrode system possesses energy and power densities of 10.40 W h kg(-1) and 6.96 kW kg(-1), respectively. These values are comparable to those of other energy storage devices. Therefore, diamond supercabatteries are promising for many industrial applications. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
Language |
|
Wos |
000489646900036 |
Publication Date |
2019-09-06 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
2040-3364 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
7.367 |
Times cited |
26 |
Open Access |
|
|
Notes |
; S. Yu and K. J. Sankaran contributed equally to this work. N. Yang acknowledges funding from the German Science Foundation under the project of YA344/1-1. J. Verbeeck and S. Korneychuk acknowledge the funding from the GOA project “Solarpaint” of the University of Antwerp. The Qu-Ant-EM microscope was partly funded by the Hercules fund from the Flemish Government. K. J. Sankaran and K. Haenen like to acknowledge the financial support of the Methusalem “NANO” network. S. Yu likes to acknowledge the financial support from fundamental research funds for the central universities (Grant No. SWU019001). ; |
Approved |
Most recent IF: 7.367 |
|
Call Number |
UA @ admin @ c:irua:163723 |
Serial |
5388 |
Permanent link to this record |