Abstract: Sodium-ion batteries (SIBs) are potential cost-effective solutions for stationary energy storage applications. Unavailability of suitable anode materials, however, is one of the important barriers to the maturity of SIBs. Here, we report a Na2+xTi4O9/C composite as a promising anode candidate for SIBs with high capacity and cycling stability. This anode is characterized by a capacity of 124 mAh g(-1) (plus 11 mAh g(-1) contributed by carbon black), an average discharge potential of 0.9 V vs Na/Na+, a good rate capability and a high stability (89% capacity retention after 250 cycles at a rate of 1 degrees C). The mechanisms of sodium insertion/deinsertion and of the formation of Na2+xTi4O9/C are investigated with the aid of various ex/in situ characterization techniques. The in situ formed carbon is necessary for the formation of the reduced sodium titanate. This synthesis method may enable the convenient synthesis of other composites of crystalline phases with amorphous carbon.

Abstract: Sodium ion batteries (NIBs) are one of the versatile technologies for lowcost rechargeable batteries. O3-type layered sodium transition metal oxides (NaMO2, M = transition metal ions) are one of the most promising positive electrode materials considering their capacity. However, the use of O3 phases is limited due to their low redox voltage and associated multiple phase transitions which are detrimental for long cycling. Herein, a simple strategy is proposed to successfully combat these issues. It consists of the introduction of a larger, nontransition metal ion Sn4+ in NaMO2 to prepare a series of NaNi0.5Mn0.5−y SnyO2 (y = 0–0.5) compositions with attractive electrochemical performances, namely for y = 0.5, which shows a single-phase transition from O3 ⇔ P3 at the very end of the oxidation process. Na-ion NaNi0.5Sn0.5O2/C coin cells are shown to deliver an average cell voltage of 3.1 V with an excellent capacity retention as compared to an average stepwise voltage of ≈2.8 V and limited capacity retention for the pure NaNi0.5Mn0.5O2 phase. This study potentially shows the way to manipulate the O3 NaMO2 for facilitating their practical use in NIBs.

Abstract: Socially responsible investments can be defined as an investment process that integrates ethical values and environmental protection, improving social conditions, and good governance into a traditional investment decision. This integration is mainly a consequence of the growing importance that investors give to environmental, social, and governance (ESG) criteria, resulting in more sustainable development. Also, in the real estate sector, increased attention is being paid to the contributions made to integrate economic, environmental, and social factors into decisions. The ESG framework looks closely at how companies are managed, and the impact related to their market value. The factors for investors’ focus are summarized as environmental, social, and governance. The term ESG was coined in a 2004 United Nations (UN) report titled “Who Cares Wins,” aimed at raising awareness regarding the importance of environmental, social, and corporate governance issues in financial markets. The ESG criteria’s specific purpose is to guide investors in recognizing sustainable investments without evaluating how sustainable the asset is or the investment value represented by sustainability. It is essential to underline that ESG does not take specific economic interests into account. The rationale behind this apparent gap is that investors investigate the economic aspects before investing. However, by not explicitly linking ESG and economic criteria, attractive investments are often misjudged and not implemented. For example, investments that only show their value in the longer term or indirectly influence value by achieving a higher retention rate among incumbent tenants, reducing or eliminating friction costs. A product–service system (PSS) refers to a market proposition (business model) that builds on a product’s traditional functionality by incorporating additional services. Although services are already offered, the PSS function is to link the service to a product. The service thereby supports the operation of the product and generates additional benefits. It encompasses the integrated solutions of products and services to satisfy customers' needs and generate maximum value. According to Sutanto et al., a PSS is designed to focus on sustainability characterized in three dimensions. 1. The economic dimension 2. The environmental dimension 3. The social dimension When discussing sustainability in this thesis, we use the criteria listed above related to socially responsible investments. The link between PSS and ESG is that a PSS focuses on creating a sustainable system, and ESG makes sustainability more visible to investors. Therefore, when PSS are recognized and implemented in buildings, they must be evaluated using ESG analysis methods. Product-Service Systems (PSS) try to find a way to offer services on top of a product. The product is essentially secondary to the result that is delivered from the services. For example, the modem (product) that a cable company provides will be of secondary importance to the connectivity (service). Alternatively, it will be less critical how heat is made (product) than the intended set point is achieved in the building. PSSs transform the supply of products into services. In doing so, the responsibility shifts from delivering a product (once only) to continuous service delivery. Therefore, it is in the best interest of the service provider to deliver the outcome of the service as efficiently (read: lowest cost) as possible. A direct consequence of this is that the service provider will want to use the product as efficiently as possible and as long as possible to reduce his costs. Therefore, the supplier will also want to recover and maximize the reuse of his product based on the same rationale. A positive impact on the environment and the used raw materials is thus to be expected. The whole process of servitization (transforming products into services) in real estate will positively impact the Economic, Environmental and Social factors. Therefore, demonstrating this proposition is the main objective of this thesis. Smart PSS is the same idea as Product-Service systems but in which the digitization of the services plays a key role. It will be shown that by digitizing services, a broader range can be offered. It will be demonstrated that products that provide services at the building level can, through their interconnectedness, also provide services to external systems (e.g. electricity grid, urban planning, mobility, ...). At the same time, digitizing the products and services will also underpin trust in the systems and allow for proper remuneration. In this PhD, different standard systems in a building, such as the reservation system, the water heater, or the fire detection system, are equipped with additional services. A PSS is often specifically designed to focus on economic, social, and environmental dimensions. These dimensions correspond to the investor’s examination as part of the ESG analysis before investing. As the PSS is often specifically designed to integrate sustainability, there is a close link between the sustainability performance of the PSS and the ESG criteria evaluated by the investor. Throughout the work, the owner is considered to be the user of the building. It is not the case that only an owner-user can generate cash flow. In essence, if they have sufficient rights to the underlying product, any building user can activate services that generate cash flow. In today's market, it is logical that this is viewed in the owner-user context as they will usually choose the products to be installed in larger technical installations. They may have previously used a PSS or choose to move to one. However, a building’s tenant could choose to lease out their meeting rooms if they are not contractually prohibited from doing so since, in practice, contracts have begun to prohibit certain services. For example, rental contracts that actively prohibit renting out a property through platforms such as Airbnb. Thus, the user’s function could potentially impact how the PSS is designed. This work does not explicitly explore the impact of this aspect. The owner-user is assumed throughout this manuscript. The second chapter describes the state of affairs concerning PSSs in a broad framework evolving towards focusing on the real estate sector. After which, in the second chapter, ESG and the link to real estate and how smart real estate (smart buildings) is missing from this evaluation are discussed in more detail. Chapter 3 shows from a fire alarm system, which was extended with an evacuation support system, the usefulness, and the risk of data. Further work was done to demonstrate the added value in terms of Economic, Environmental and Social factors of standard installations in buildings. In Chapter 4, a simple sanitary hot water boiler is extended with a service that allows controlling this boiler according to the status of the electricity grid (surplus or shortage of energy). The supply and demand of energy on the power grid must be equal at all times. By equipping a classic water heater (product) with additional intelligence (service), it becomes possible to adjust the energy use to the grid's needs. The grid operators are prepared to pay for this. This payment can be linked to different energy markets (long term market, spot market, ...). This study looked at the fee that would have to be paid when the adjustment of the energy use can be made instantaneously so that the fee must be settled according to the prices on the imbalance market. In chapter 5, we look at the impact of the service to rent out free spaces as co-working places on a broad market (external to the building), compared to a regular reservation system. By renting out unused workplaces on a broad market, the utilization of the existing patrimony will be higher. The demand for new square meters with the same function will decrease as the supply-demand curve changes, and so will the price. This makes it less interesting to build new buildings. Less construction of new buildings will result in fewer resources being used, which will positively affect the environment. In addition, fewer new buildings with an office function will leave more space for buildings with another function. Also, the city's infrastructure will be less burdened (roads, sewerage, electricity grid,...). In The Hague, the decreasing need for new square meters of office buildings can lead to more space for affordable housing, for which the city has a great need. Chapter 6 will frame the valuation of service as a real options method that gives an impetus to a general valuation methodology to value the flexibility that Smart PSS inherently has. Finally, this thesis demonstrates that (smart) PSSs impact real estate profitability, while positively influencing environmental and social factors. Further research and the limitations of the studies conducted are documented. This PhD concludes that Product-Service systems should break the silos between different stakeholders, resulting in a lower total cost of ownership of buildings in the longer term. This can only be achieved if the valuation of Product-Service systems is done correctly and is recognized by every stakeholder in the real estate process.

Abstract: SmFe8.75 Si-0.25 C/alpha-Fe nanocomposites have been successfully synthesized using high energy milling, followed by annealing at 750 degrees C. The crystal structure of these compounds was characterized by the Rietveld method using powder X-ray diffraction data. By increasing the concentration of Sm, we observed a decrease in the amount of alpha-Fe phase. The morphology of the samples was determined by scanning and transmission electron microscopy. The average grain size is about 20 nm. The magnetic properties were investigated at room temperature and at 10 K. A ferromagnetic behavior was observed in all samples at both temperatures. An increase of the soft magnetic phase alpha-Fe induced an increase in the magnetization and a decrease in coercivity. (C) 2016 Elsevier B.V. All rights reserved.

Abstract: Small stationary diesel engines, like in generator sets, have limited emission control measures and are therefore responsible for 44% of the particulate matter (PM) emissions in the United States. The diesel exhaust composition depends on operating conditions of the combustion engine. Furthermore, the measurements are influenced by the used sampling method. This study examines the effect of engine loading and exhaust gas dilution on the composition of small-scale power generators. These generators are used in different operating conditions than road-transport vehicles, resulting in different emission characteristics. Experimental data were obtained for gaseous volatile organic compounds (VOC) and PM mass concentration, elemental composition and nitrate content. The exhaust composition depends on load condition because of its effect on fuel consumption, engine wear and combustion temperature. Higher load conditions result in lower PM concentration and sharper edged particles with larger aerodynamic diameters. A positive correlation with load condition was found for K, Ca, Sr, Mn, Cu, Zn and Pb adsorbed on PM, elements that originate from lubricating oil or engine corrosion. The nitrate concentration decreases at higher load conditions, due to enhanced nitrate dissociation to gaseous NO at higher engine temperatures. Dilution on the other hand decreases PM and nitrate concentration and increases gaseous VOC and adsorbed metal content. In conclusion, these data show that operating and sampling conditions have a major effect on the exhaust gas composition of small-scale diesel generators. Therefore, care must be taken when designing new experiments or comparing literature results.

Abstract: Size, number density and volume fraction of nano-precipitates are important microstructural parameters controlling the strengthening of materials. In this work a widely accessible, convenient, moderately time efficient method with acceptable accuracy and precision has been provided for measurement of volume fraction of nano-precipitates in crystalline materials. The method is based on the traditional but highly accurate technique of measuring foil thickness via convergent beam electron diffraction. A new equation is proposed and verified with the aid of 3-dimensional atom probe (3DAP) analysis, to compensate for the additional error resulted from the hardly distinguishable contrast of too short incomplete precipitates cut by the foil surface. The method can be performed on a regular foil specimen with a modem LaB6 or field-emission-gun transmission electron microscope. Precisions around +/- 16% have been obtained for precipitate volume fractions of needle-like beta ''/C and Q precipitates in an aged Al-Mg-Si-Cu alloy. The measured number density is dose to that directly obtained using 3DAP analysis by a misfit of 45%, and the estimated precision for number density measurement is about +/- 11%. The limitations of the method are also discussed.

Abstract: Site selective doping of aligned carbon nanostructures represents a promising approach for their implementation in actual devices. In the present work we report on alkali metals decoration on low density vertically aligned carbon nanotubes, disclosing the possibility of engineering site selective depositions of potassium atoms on the carbon systems. Photoemission measurements were combined with microscopy demonstrating the effective spatial control of alkali deposition. The changes of electronic structures of locally doped carbon regions were studied by exploiting the ability of the scanning photoemission microscopy technique. From the analysis of experimental data supported by theoretical calculations, we show the tuning of the charge transfer from potassium to carbon atoms belonging to neighboring nanotubes or along the same tube structure.

Abstract: Single-sided fluorination has been predicted to open an electronic band gap in graphene and to exhibit unique electronic and magnetic properties; however, this has not been substantiated by experimental reports. Our comprehensive experimental and theoretical study of this material on a SiC(0001) substrate shows that single-sided fluorographene exhibits two phases, a stable one with a band gap of similar to 6 eV and a metastable one, induced by UV irradiation, with a band gap of similar to 2.5 eV. The metastable structure, which reverts to the stable “ground-state” phase upon annealing under emission of blue light, in our view is induced by defect states, based on the observation of a nondispersive electronic state at the top of the valence band, not unlike that found in organic molecular layers. Our structural data show that the stable C2F ground state has a “boat” structure, in agreement with our X-ray magnetic circular dichroism data, which show the absence of an ordered magnetic phase. A high flux of UV or X-ray photons removes the fluorine atoms, demonstrating the possibility of lithographically patterning conducting regions into an otherwise semiconducting 2D material.

Abstract: Single nucleotide point mutations in the KRAS oncogene occur frequently in human cancers, rendering them intriguing targets for diagnosis, early detection and personalized treatment. Current detection methods are based on polymerase chain reaction, sometimes combined with next-generation sequencing, which can be expensive, complex and have limited availability. Here, we propose a novel singlet oxygen (1O2)-based photoelectrochemical detection methodology for single-point mutations, using KRAS mutations as a case study. This detection method combines the use of a sandwich assay, magnetic beads and robust chemical photosensitizers, that need only air and light to produce 1O2, to ensure high specificity and sensitivity. We demonstrate that hybridization of the sandwich hybrid at high temperatures enables discrimination between mutated and wild-type sequences with a detection rate of up to 93.9%. Additionally, the presence of background DNA sequences derived from human cell-line DNA, not containing the mutation of interest, did not result in a signal, highlighting the specificity of the methodology. A limit of detection as low as 112 pM (1.25 ng/mL) was achieved without employing any amplification techniques. The developed 1O2-based photoelectrochemical methodology exhibits unique features, including rapidity, ease of use, and affordability, highlighting its immense potential in the field of nucleic acid-based diagnostics.

Abstract: Single crystals of Ln5Ru2O12 (Ln=Pr, Nd, SmTb) were grown out of either NaOH or KOH fluxes in sealed silver tubes. The crystals of all the phases were observed to be twinned as confirmed by TEM studies. The series crystallize in the C2/m monoclinic system with lattice parameters, a=12.4049(4)12.7621(6) Å, b=5.8414(2)5.9488(3) Å, c=7.3489(2)7.6424(4) Å, β=107.425(3)107.432(2)° and Z=2. The crystal structure is isotypic with the defect/disorder model of Ln5Re2O12 (Ln = Y, Gd) and consists of one dimensional edge shared RuO6 octahedral chains separated by a two dimensional LnOx polyhedral framework. Magnetic measurements indicate paramagnetic and antiferromagnetic behavior for Ln=Nd, SmGd and Ln=Tb, respectively.

Abstract: Single crystal antimony-doped SnO2 whiskers have been synthesized by in situ doping process in horizontal flow reactor. The produced whiskers were modified with 0.1, 0.2, 0.5, 1 or 2 wt.% Pd. The processes of Pd particles growth and aggregation are described on the base of AFM and STEM data. Depending on the content of introduced Pd precursor, the various mechanisms (Volmer-Weber or Stranski-Krastanov) of Pd nanoparticles growth realize. The dependence of sensor signal to CO on Pd concentration has non-monotonous character determined by the size of Pd nanoparticles and their aggregation degree. The best sensor signal toward CO was observed for whiskers decorated with 0.1 wt.% Pd. This concentration corresponds to the presence of individual 3-5 nm Pd nanoparticles on the surface of the whiskers. (C) 2013 Elsevier B.V. All rights reserved.

Abstract: Since the successful synthesis of bulk single crystals MoN2 and ReN2, which have a layered structure, transition-metal dinitrides have attracted considerable attention in recent years. Here, we focus on rare-earth metal (Rem) elements, and propose seven stable Rem dinitride monolayers with a 1T structure, namely, 1T-RemN2. We use first-principles calculations, and find that these monolayers have a ferromagnetic ground state with in-plane magnetization. Without spin-orbit coupling (SOC), the band structures are spin-polarized with Dirac points at the Fermi level. Remarkably, the 1T-LuN2 monolayer exhibits an isotropic magnetocrystalline anisotropy energy in the xy plane with in-plane magnetization, indicating easy tunability of the magnetization direction. When rotating the magnetization vector in the xy plane, we propose a model that accurately describes the variation of the SOC band gap and the two possible topological states (Weyl-like semimetal and Chern insulator states) whose properties are tunable. The Weyl-like semimetal state is a critical point between the two Chern insulator states with opposite sign of the Chern numbers (+/- 1). The nontrivial band gap (up to 60.3 meV) and the Weyl-like semimetal state are promising for applications in spintronic devices.

Abstract: Since the onset of pattern transfer technologies for chip manufacturing, various strategies have been developed to circumvent or overcome aspect ratio dependent etching (ARDE). These methods have, however, their own limitations in terms of etch non-idealities, throughput or costs. Moreover, they have mainly been optimized for individual in-device features and die-scale patterns, while occasionally ending up with poor patterning of metrology marks, affecting the alignment and overlay in lithography. Obtaining a better understanding of the underlying mechanisms of ARDE and how to mitigate them therefore remains a relevant challenge to date, for both marks and advanced nodes. In this work, we accordingly assessed the neutral transport mechanisms in ARDE by means of experiments and multiscale modeling for SiO₂etching with CHF₃/Ar and CF₄/Ar plasmas. The experiments revealed a local maximum in the etch rate for an aspect ratio around unity, i.e. the simultaneous occurrence of regular and inverse reactive ion etching lag for a given etch condition. We were able to reproduce this ARDE trend in the simulations without taking into account charging effects and the polymer layer thickness, suggesting shadowing and diffuse reflection of neutrals as the primary underlying mechanisms. Subsequently, we explored four methods with the simulations to regulate ARDE, by varying the incident plasma species fluxes, the amount of polymer deposition, the ion energy and angular distribution and the initial hardmask sidewall angle, for which the latter was found to be promising in particular. Although our study focusses on feature dimensions characteristic to metrology marks and back-end-of-the-line integration, the obtained insights have a broader relevance, e.g. to the patterning of advanced nodes. Additionally, this work supports the insight that physisorption may be more important in plasma etching at room temperature than originally thought, in line with other recent studies, a topic on which we recommend further research.

Abstract: Since the advent of graphene, other 2D materials have garnered interest; notably the single element materials silicene, germanene, and stanene. Weinvestigate the ballistic current-voltage (I-V) characteristics of armchair silicene and stanene armchair nanoribbons (AXNRs with X = Si, Sn) using a combination of density functional theory and non-equilibrium Green's functions. The impact of out-of-plane electric field and in-plane uniaxial strain on the ribbon geometries, electronic structure, and (I-V)s are considered and contrasted with graphene. Since silicene and stanene are sp(2)/sp(3) buckled layers, the electronic structure can be tuned by an electric field that breaks the sublattice symmetry, an effect absent in graphene. This decreases the current by similar to 50% for Sn, since it has the largest buckling. Uniaxial straining of the ballistic channel affects the AXNR electronic structure in multiple ways: it changes the bandgap and associated effective carrier mass, and creates a local buckling distortion at the lead-channel interface which induces a interface dipole. Due to the increasing sp(3) hybridization character with increasing element mass, large reconstructions rectify the strained systems, an effect absent in sp(2) bonded graphene. This results in a smaller strain effect on the current: a decrease of 20% for Sn at 15% tensile strain compared to a similar to 75% decrease for C.

Abstract: Since invention of the diamond anvil cell technique in the late 1950s for studying materials at extreme conditions, the maximum static pressure generated so far at room temperature was reported to be about 400 GPa. Here we show that use of micro-semi-balls made of nanodiamond as second-stage anvils in conventional diamond anvil cells drastically extends the achievable pressure range in static compression experiments to above 600 GPa. Micro-anvils (10-50 mu m in diameter) of superhard nano-diamond (with a grain size below similar to 50 nm) were synthesized in a large volume press using a newly developed technique. In our pilot experiments on rhenium and gold we have studied the equation of state of rhenium at pressures up to 640 GPa and demonstrated the feasibility and crucial necessity of the in situ ultra high-pressure measurements for accurate determination of material properties at extreme conditions.