Records |
Author |
Jimenez-Mena, N.; Jacques, P.J.; Ding, L.; Gauquelin, N.; Schryvers, D.; Idrissi, H.; Delannay, F.; Simar, A. |
Title |
Enhancement of toughness of Al-to-steel Friction Melt Bonded welds via metallic interlayers |
Type |
A1 Journal article |
Year |
2019 |
Publication |
Materials science and engineering: part A: structural materials: properties, microstructure and processing |
Abbreviated Journal |
Mat Sci Eng A-Struct |
Volume |
740-741 |
Issue |
|
Pages |
274-284 |
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
Abstract |
The toughness of Al-to-steel welds decreases with increasing thickness of the intermetallic (IM) layer formed at the interface. Co plating has been added as interlayer in Al-to-steel Friction Melt Bonded (FMB) welds to control the nature and thickness of the IM layer. In comparison to a weld without interlayer, Co plating brings about a reduction of the thickness of the IM layer by 70%. The critical energy release rate of the crack propagating in the weld is used as an indicator of toughness. It is evaluated via an adapted crack propagation test using an energy conservation criterion. For a weld without interlayer, critical energy release rate is found to increase when the thickness of the intermetallic layer decreases. When the intermetallic layer is thick, the crack propagates in a brittle manner through the intermetallic whereas, at low layer thickness, the crack deviates and partially propagates through the Al plate, which causes an increase of toughness. The use of a Co interlayer brings about an increase of toughness by causing full deviation of the crack towards the Al plate. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
000453494500029 |
Publication Date |
2018-10-24 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title ![sorted by Abbreviated Series Title field, ascending order (up)](img/sort_asc.gif) |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0921-5093 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
3.094 |
Times cited |
4 |
Open Access |
Not_Open_Access: Available from 25.10.2020
|
Notes |
The authors acknowledge the financial support of the Interuniversity Attraction Poles Program from the Belgian State through the Belgian Policy Agency, Belgium, contract IAP7/21 INTEMATE. N. Jimenez-Mena acknowledges the financial support of the (Fonds pour la formation à la recherchedans l'industrie et dans l'agriculture (FRIA), Belgium. A. Simar acknowledges the financial support of the (European Research Council – Starting Grant (ERC-StG), project ALUFIX, grant agreement no 716678. H. Idrissi is mandated by the Belgian National Fund for Scientific Research (FSR-FNRS), Belgium. The authors also acknowledge M. Coulombier for the help provided in the measurement of the friction coefficient, and T. Pardoen and F. Lani for the fruitful discussions. |
Approved |
Most recent IF: 3.094 |
Call Number |
EMAT @ emat @c:irua:154866UA @ admin @ c:irua:154866 |
Serial |
5061 |
Permanent link to this record |
|
|
|
Author |
Zhao, L.; Macias, J.G.S.; Ding, L.; Idrissi, H.; Simar, A. |
Title |
Damage mechanisms in selective laser melted AlSi10Mg under as built and different post-treatment conditions |
Type |
A1 Journal article |
Year |
2019 |
Publication |
Microstructure And Processing |
Abbreviated Journal |
Mat Sci Eng A-Struct |
Volume |
764 |
Issue |
764 |
Pages |
138210 |
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
Abstract |
Selective laser melting (SLM) manufactured AlSi10Mg alloys present a fine silicon-rich network and precipitates which grant high mechanical strength but low ductility. Post-treatments, aiming at eliminating inherent defects related to SLM such as residual stresses, porosity or inhomogeneity, result in significant changes in the microstructure and impact both the hardening and the damage mechanisms of the post-treated material. The present work is dedicated to the investigation of the fracture of SLM AlSi10Mg under as built and three post-treatment conditions, namely two stress relieve heat treatments and friction stir processing (FSP). It is found that the interconnected Si network fosters damage at low strain due to the brittleness of the Si phase. The onset of damage transfers load to the enclosed Al phase which then fractures quickly under high stress, thus leading to low material ductility. In contrast, when the Si network is globularized into Si particles, the ductility is highly increased even in the case where the porosity and inhomogeneity of the microstructure remain after the post-treatment. The ductility enhancement results from the delay in void nucleation on the Si particles as well as from the tolerance for void growth in the Al matrix. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
000486360100029 |
Publication Date |
2019-07-27 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title ![sorted by Abbreviated Series Title field, ascending order (up)](img/sort_asc.gif) |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0921-5093 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
3.094 |
Times cited |
1 |
Open Access |
|
Notes |
; This research work has been supported by the WALInnov LongLifeAM project, Convention n 1810016, funded by Service public de Wallonie Economic Emploi Recherche (SPW-EER). L. Ding and A. Simar acknowledge the financial support of the European Research Council (ERC) for the Starting Grant ALUFIX project (grant agreement n 716678). J. G. Santos Macias acknowledges the support of the Fonds de la recherche scientifique -FNRS (FRIA grant), Belgium. H. Idrissi is mandated by the Belgian National Fund for Scientific Research (FSRFNRS). Any-Shape is acknowledged for material supply. We thank Prof. P. J. Jacques from UCLouvain for fruitful discussion and critical reading of the paper. ; |
Approved |
Most recent IF: 3.094 |
Call Number |
UA @ admin @ c:irua:162800 |
Serial |
5386 |
Permanent link to this record |
|
|
|
Author |
Zhao, L.; Ding, L.; Soete, J.; Idrissi, H.; Kerckhofs, G.; Simar, A. |
Title |
Fostering crack deviation via local internal stresses in Al/NiTi composites and its correlation with fracture toughness |
Type |
A1 Journal article |
Year |
2019 |
Publication |
Composites: part A: applied science and manufacturing |
Abbreviated Journal |
Compos Part A-Appl S |
Volume |
126 |
Issue |
126 |
Pages |
105617 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
In the framework of metal matrix composites, a research gap exists regarding tailoring damage mechanisms. The present work aims at developing an Al/NiTi composite incorporating internal stresses in the vicinity of reinforcements. The composite is manufactured by friction stir processing which allows a homogenous NiTi distribution and a good Al/NiTi interface bonding. The internal stresses are introduced via shape memory effect of the embedded NiTi particles. The induced internal strain field is confirmed by digital image correlation and the corresponding stress field is evaluated by finite element simulation. It is found that the damage mechanism is modified in the presence of internal stresses. The consequent enhancement of fracture toughness arises by the fact that the internal stresses foster discrete damages shifted from the fracture ligament line. These damages release the stress concentration at the main crack tip and lead to a deviated crack path when coalescing to accommodate fracture propagation. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
000489350600025 |
Publication Date |
2019-09-05 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title ![sorted by Abbreviated Series Title field, ascending order (up)](img/sort_asc.gif) |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
1359-835x |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
4.075 |
Times cited |
|
Open Access |
|
Notes |
; This research work has been exclusively supported by the European Research Council (ERC) under the European Union's Horizon 2020 research and innovation program (grant agreement no 716678). The X-ray computed,tomography facilities of the Department of Materials Engineering of the KU Leuven are financed by the Hercules Foundation. H. Idrissi is mandated by the Belgian National Fund for Scientific Research (FSR-FNRS). The authors acknowledge Professor F. Delannay from UCLouvain for fruitful discussions. ; |
Approved |
Most recent IF: 4.075 |
Call Number |
UA @ admin @ c:irua:163706 |
Serial |
5387 |
Permanent link to this record |
|
|
|
Author |
Lezaack, M.B.; Hannard, F.; Zhao, L.; Orekhov, A.; Adrien, J.; Miettinen, A.; Idrissi, H.; Simar, A. |
Title |
Towards ductilization of high strength 7XXX aluminium alloys via microstructural modifications obtained by friction stir processing and heat treatments |
Type |
A1 Journal article |
Year |
2021 |
Publication |
Materialia |
Abbreviated Journal |
|
Volume |
20 |
Issue |
|
Pages |
101248 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
High strength 7XXX aluminium series reach exceptional strength, higher than all other industrial aluminium alloys. However, they suffer from a lack of ductility compared to softer series. This work presents a procedure to improve the ductility of 7475 Al alloy in high strength condition, reaching a true fracture strain of 70% at full 500 MPa T6 yield strength. Using friction stir processing (FSP) and post-FSP heat treatments, 100% of industrial rolled material T6 yield stress is maintained but a 180% increase in fracture strain is measured for the processed material. This ductility improvement is studied by in-situ synchrotron X-ray tomography and is explained by the reduction of intermetallic particles size and the homogenization of their spatial distribution. Furthermore, the microstructure after FSP shows equiaxed refined grains which favour crack deviation as opposed to large cracks parallel to the elongated coarse grains in rolled plate. These results are paving the way to better formability and crashworthiness of 7XXX alloys. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
000718127100006 |
Publication Date |
2021-10-19 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title ![sorted by Abbreviated Series Title field, ascending order (up)](img/sort_asc.gif) |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
2589-1529 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
|
Times cited |
|
Open Access |
Not_Open_Access |
Notes |
|
Approved |
Most recent IF: NA |
Call Number |
UA @ admin @ c:irua:184145 |
Serial |
6894 |
Permanent link to this record |
|
|
|
Author |
Ding, L.; Sapanathan, T.; Schryvers, D.; Simar, A.; Idrissi, H. |
Title |
On the formation of antiphase boundaries in Fe₄Al₁₃ intermetallics during a high temperature treatment |
Type |
A1 Journal article |
Year |
2022 |
Publication |
Scripta materialia |
Abbreviated Journal |
Scripta Mater |
Volume |
215 |
Issue |
|
Pages |
114726-6 |
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
Abstract |
In this paper, we report atomic scale observations and formation mechanisms of a high-density of antiphase boundaries (APBs) within an ultra-fine-grained Fe4Al13 intermetallic layer at an Al/steel interface after a heat treatment at 596 degrees C. The results reveal that the APBs are formed by nucleation and the glide of partial dislocations with Burgers vector of b/3[010] (b = 12.47 angstrom). The intensive activation of APBs locally transforms the Fe4Al13 structure from the quasicrystal approximant structure to a quasicrystal. Very few stacking faults and nanotwins are observed indicating that the formation of planar defects is mainly driven by this transformation. This new insight on the formation of high density of APBs could possibly lead to an improvement in toughness by increasing the strength/ductility balance of this intermetallic. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
000800016600003 |
Publication Date |
2022-04-08 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title ![sorted by Abbreviated Series Title field, ascending order (up)](img/sort_asc.gif) |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
1359-6462 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
6 |
Times cited |
|
Open Access |
OpenAccess |
Notes |
|
Approved |
Most recent IF: 6 |
Call Number |
UA @ admin @ c:irua:188644 |
Serial |
7088 |
Permanent link to this record |
|
|
|
Author |
Arseenko, M.; Hannard, F.; Ding, L.; Zhao, L.; Maire, E.; Villanova, J.; Idrissi, H.; Simar, A. |
Title |
A new healing strategy for metals : programmed damage and repair |
Type |
A1 Journal article |
Year |
2022 |
Publication |
Acta materialia |
Abbreviated Journal |
Acta Mater |
Volume |
238 |
Issue |
|
Pages |
118241-10 |
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
Abstract |
Self-healing strategies aim at avoiding part repair or even replacement, which is time consuming, expen-sive and generates waste. However, strategies for metallic systems are still under-developed and solid-state solutions for room temperature service are limited to nano-scale damage repair. Here we propose a new healing strategy of micron-sized damage requiring only short and low temperature heating. This new strategy is based on damage localization particles, which can be healed by fast diffusing atoms of the matrix activated during heat treatment. The healing concept was successfully validated with a com-mercial aluminum alloy and manufactured by Friction Stir Processing (FSP). Damage was demonstrated to initiate on particles that were added to the matrix during material processing. In situ 2D and 3D nano -imaging confirmed healing of the damaged material and showed that heating this material for 10 min at 400 degrees C is sufficient to heal incipient damage with complete filling of 70% of all damage (and up to 90% when their initial size is below 0.2 mu m). Furthermore, strength is retained and the work of fracture of the alloy is improved by about 40% after healing. The proposed Programmed Damage and Repair healing strategy could be extended to other metal based systems presenting precipitation. (C) 2022 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
000843502700006 |
Publication Date |
2022-08-03 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title ![sorted by Abbreviated Series Title field, ascending order (up)](img/sort_asc.gif) |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
1359-6454 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
9.4 |
Times cited |
|
Open Access |
Not_Open_Access |
Notes |
|
Approved |
Most recent IF: 9.4 |
Call Number |
UA @ admin @ c:irua:190561 |
Serial |
7121 |
Permanent link to this record |
|
|
|
Author |
Krishnamurthy, S.C.; Arseenko, M.; Kashiwar, A.; Dufour, P.; Marchal, Y.; Delahaye, J.; Idrissi, H.; Pardoen, T.; Mertens, A.; Simar, A. |
Title |
Controlled precipitation in a new Al-Mg-Sc alloy for enhanced corrosion behavior while maintaining the mechanical performance |
Type |
A1 Journal article |
Year |
2023 |
Publication |
Materials characterization |
Abbreviated Journal |
|
Volume |
200 |
Issue |
|
Pages |
112886-11 |
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
Abstract |
The hot working of 5xxx series alloys with Mg ≥3.5 wt% is a concern due to the precipitation of β (Al3Mg2) phase at grain boundaries favoring Inter Granular Corrosion (IGC). The mechanical and corrosion properties of a new 5028-H116 Al-Mg-Sc alloy under various β precipitates distribution is analyzed by imposing different cooling rates from the hot forming temperature (i.e. 325 °C). The mechanical properties are maintained regardless of the heat treatment. However, the different nucleation sites and volume fractions of β precipitates for different cooling rates critically affect IGC. Controlled furnace cooling after the 325 °C heat treatment is ideal in 5028-H116 alloy to reduce susceptibility to IGC after sensitization. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
000977059100001 |
Publication Date |
2023-04-03 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title ![sorted by Abbreviated Series Title field, ascending order (up)](img/sort_asc.gif) |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
1044-5803 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
4.7 |
Times cited |
|
Open Access |
OpenAccess |
Notes |
|
Approved |
Most recent IF: 4.7; 2023 IF: 2.714 |
Call Number |
UA @ admin @ c:irua:195598 |
Serial |
7291 |
Permanent link to this record |
|
|
|
Author |
Gheysen, J.; Kashiwar, A.; Idrissi, H.; Villanova, J.; Simar, A. |
Title |
Suppressing hydrogen blistering in a magnesium-rich healable laser powder bed fusion aluminum alloy analyzed by in-situ high resolution techniques |
Type |
A1 Journal article |
Year |
2023 |
Publication |
Materials & design |
Abbreviated Journal |
|
Volume |
231 |
Issue |
|
Pages |
112024-11 |
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
Abstract |
Hydrogen blistering, i.e. precipitation of supersaturated hydrogen at elevated temperatures, increases porosity during heat treatments in 4xxx series Al alloys manufactured by laser powder bed fusion (LPBF), as demonstrated by 3D X-ray nano-imaging in AlSi12. This paper proposes the design of a healable Al alloy to suppress hydrogen blistering and improve the damage management. The strategy consists of solute atoms diffusing towards nano-voids and precipitating on their surface, thereby filling the damage sites. A new healable Al alloy was thus developed and successfully manufactured by LPBF. 3D X-ray nano-imaging evidenced that the addition of Mg in 4xxx series Al alloys suppresses the hydrogen blistering. This is expectedly due to Mg in solid solution which increases the hydrogen solubility in the Al matrix and due to the healing of these hydrogen pores. Moreover, a significant healing of voids smaller than 500 nm diameter is observed. In-situ heating inside transmission electron microscopy pointed out that Al matrix diffuses inside the fractured Mg2Si particles, thereby demonstrating the healing ability of the new alloy. This has opened the doors to development of new healable Al alloys manufactured by LPBF as well as to new post-treatments to tailor mechanical properties and microstructure without hydrogen blistering. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
001055174900001 |
Publication Date |
2023-05-20 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title ![sorted by Abbreviated Series Title field, ascending order (up)](img/sort_asc.gif) |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0264-1275; 1873-4197 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
8.4 |
Times cited |
|
Open Access |
OpenAccess |
Notes |
|
Approved |
Most recent IF: 8.4; 2023 IF: 4.364 |
Call Number |
UA @ admin @ c:irua:196536 |
Serial |
8939 |
Permanent link to this record |
|
|
|
Author |
Kashiwar, A.; Arseenko, M.; Simar, A.; Idrissi, H. |
Title |
On the role of microstructural defects on precipitation, damage, and healing behavior in a novel Al-0.5Mg2Si alloy |
Type |
A1 Journal article |
Year |
2024 |
Publication |
Materials & design |
Abbreviated Journal |
|
Volume |
239 |
Issue |
|
Pages |
112765-112769 |
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
Abstract |
A recently developed healable Al-Mg2Si designed by the programmed damage and repair (PDR) strategy is studied considering the role microstructural defects play on precipitation, damage, and healing. The alloy incorporates sacrificial Mg2Si particles that precipitate after friction stir processing (FSP). They act as damage localization sites and are healable based on the solid-state diffusion of Al-matrix. A combination of different transmission electron microscopy (TEM) imaging techniques enabled the visualization and quantification of various crystallographic defects and the spatial distribution of Mg2Si precipitates. Intragrain nucleation is found to be the dominant mechanism for precipitation during FSP whereas grain boundaries and subgrain boundaries mainly lead to coarsening of the precipitates. The statistical and spatial analyses of the damaged particles have shown particle fracture as the dominant damage mechanism which is strongly dependent on the size and aspect ratio of the particles whereas the damage was not found to depend on the location of the precipitates within the matrix. The damaged particles are associated with dislocations accumulated around them. The interplay of these dislocations is directly visualized during healing based on in situ TEM heating which revealed recovery in the matrix as an operative mechanism during the diffusion healing of the PDR alloy. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
001194110200001 |
Publication Date |
2024-02-17 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title ![sorted by Abbreviated Series Title field, ascending order (up)](img/sort_asc.gif) |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0264-1275; 1873-4197 |
ISBN |
|
Additional Links |
UA library record; WoS full record |
Impact Factor |
8.4 |
Times cited |
|
Open Access |
Not_Open_Access |
Notes |
|
Approved |
Most recent IF: 8.4; 2024 IF: 4.364 |
Call Number |
UA @ admin @ c:irua:203298 |
Serial |
9068 |
Permanent link to this record |