“Comparison of short-channel effects in monolayer MoS2 based junctionless and inversion-mode field-effect transistors”. Agarwal T, Sorée B, Radu I, Raghavan P, Fiori G, Iannaccone G, Thean A, Heyns M, Dehaene W, Applied physics letters 108, 023506 (2016). http://doi.org/10.1063/1.4939933
Abstract: Conventional junctionless (JL) multi/gate (MuG) field-effect transistors (FETs) require extremely scaled channels to deliver high on-state current with low short-channel effect related leakage. In this letter, using ultra-thin 2D materials (e.g., monolayer MoS2), we present comparison of short-channel effects in JL, and inversion-mode (IM) FETs. We show that JL FETs exhibit better sub-threshold slope (S.S.) and drain-induced-barrier-lowering (DIBL) in comparison to IM FETs due to reduced peak electric field at the junctions. But, threshold voltage (VT) roll-off with channel length downscaling is found to be significantly higher in JL FETs than IM FETs, due to higher source/drain controlled charges (dE/dx) in the channel. Further, we show that although VT roll-off in JL FETs improves by increasing the gate control, i.e., by scaling the oxide, or channel thickness, the sensitivity of threshold voltage on structural parameters is found out to be high. (C) 2016 AIP Publishing LLC.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 3.411
Times cited: 13
DOI: 10.1063/1.4939933
|
“Non-uniform strain in lattice-mismatched heterostructure tunnel field-effect transistors”. Verreck D, Verhulst AS, Sorée B, Collaert N, Mocuta A, Thean A, Groeseneken G, Solid-State Device Research (ESSDERC), European Conference
T2 –, 46th European Solid-State Device Research Conference (ESSDERC) / 42nd, European Solid-State Circuits Conference (ESSCIRC), SEP 12-15, 2016, Lausanne, SWITZERLAND , 412 (2016)
Abstract: Because of its localized impact on the band structure, non-uniform strain at the heterojunction between lattice-mismatched materials has the potential to significantly enlarge the design space for tunnel-field effect transistors (TFET). However, the impact of a complex strain profile on TFET performance is difficult to predict. We have therefore developed a 2D quantum mechanical transport formalism capable of simulating the effects of a general non-uniform strain. We demonstrate the formalism for the GaAsxSb(1-x)/InyGa(1-y) As system and show that a performance improvement over a lattice-matched reference is indeed possible, allowing for relaxed requirements on the source doping. We also point out that the added design parameter of mismatch is not free, but limited by the desired effective bandgap at the tunnel junction.
Keywords: P1 Proceeding; Condensed Matter Theory (CMT)
|
“15-band spectral envelope function formalism applied to broken gap tunnel field-effect transistors”. Verreck D, Van de Put ML, Verhulst AS, Sorée B, Magnus W, Dabral A, Thean A, Groeseneken G, 18th International Workshop On Computational Electronics (iwce 2015) (2015). http://doi.org/10.1109/IWCE.2015.7301988
Abstract: A carefully chosen heterostructure can significantly boost the performance of tunnel field-effect transistors (TFET). Modelling of these hetero-TFETs requires a quantum mechanical (QM) approach with an accurate band structure to allow for a correct description of band-to-band-tunneling. We have therefore developed a fully QM 2D solver, combining for the first time a full zone 15-band envelope function formalism with a spectral approach, including a heterostructure basis set transformation. Simulations of GaSb/InAs broken gap TFETs illustrate the wide body capabilities and transparant transmission analysis of the formalism.
Keywords: P1 Proceeding; Condensed Matter Theory (CMT)
DOI: 10.1109/IWCE.2015.7301988
|
“Full-zone spectral envelope function formalism for the optimization of line and point tunnel field-effect transistors”. Verreck D, Verhulst AS, Van de Put M, Sorée B, Magnus W, Mocuta A, Collaert N, Thean A, Groeseneken G, Journal of applied physics 118, 134502 (2015). http://doi.org/10.1063/1.4931890
Abstract: Efficient quantum mechanical simulation of tunnel field-effect transistors (TFETs) is indispensable to allow for an optimal configuration identification. We therefore present a full-zone 15-band quantum mechanical solver based on the envelope function formalism and employing a spectral method to reduce computational complexity and handle spurious solutions. We demonstrate the versatility of the solver by simulating a 40 nm wide In0.53Ga0.47As lineTFET and comparing it to p-n-i-n configurations with various pocket and body thicknesses. We find that the lineTFET performance is not degraded compared to semi-classical simulations. Furthermore, we show that a suitably optimized p-n-i-n TFET can obtain similar performance to the lineTFET. (C) 2015 AIP Publishing LLC.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 2.068
Times cited: 9
DOI: 10.1063/1.4931890
|
“Modeling surface roughness scattering in metallic nanowires”. Moors K, Sorée B, Magnus W, Journal of applied physics 118, 124307 (2015). http://doi.org/10.1063/1.4931573
Abstract: Ando's model provides a rigorous quantum-mechanical framework for electron-surface roughness scattering, based on the detailed roughness structure. We apply this method to metallic nanowires and improve the model introducing surface roughness distribution functions on a finite domain with analytical expressions for the average surface roughness matrix elements. This approach is valid for any roughness size and extends beyond the commonly used Prange-Nee approximation. The resistivity scaling is obtained from the self-consistent relaxation time solution of the Boltzmann transport equation and is compared to Prange-Nee's approach and other known methods. The results show that a substantial drop in resistivity can be obtained for certain diameters by achieving a large momentum gap between Fermi level states with positive and negative momentum in the transport direction. (C) 2015 AIP Publishing LLC.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 2.068
Times cited: 11
DOI: 10.1063/1.4931573
|
“An envelope function formalism for lattice-matched heterostructures”. Van de Put ML, Vandenberghe WG, Magnus W, Sorée B, Physica: B : condensed matter 470-471, 69 (2015). http://doi.org/10.1016/j.physb.2015.04.031
Abstract: The envelope function method traditionally employs a single basis set which, in practice, relates to a single material because the k.p matrix elements are generally only known in a particular basis. In this work, we defined a basis function transformation to alleviate this restriction. The transformation is completely described by the known inter-band momentum matrix elements. The resulting envelope function equation can solve the electronic structure in lattice matched heterostructures without resorting to boundary conditions at the interface between materials, while all unit-cell averaged observables can be calculated as with the standard envelope function formalism. In the case of two coupled bands, this heterostructure formalism is equivalent to the standard formalism while taking position dependent matrix elements. (C) 2015 Elsevier B.V. All rights reserved
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 1.386
Times cited: 5
DOI: 10.1016/j.physb.2015.04.031
|
“Modeling of inter-ribbon tunneling in graphene”. Van de Put ML, Vandenberghe WG, Magnus W, Sorée B, Fischetti MV, 18th International Workshop On Computational Electronics (iwce 2015) (2015)
Abstract: The tunneling current between two crossed graphene ribbons is described invoking the empirical pseudopotential approximation and the Bardeen transfer Hamiltonian method. Results indicate that the density of states is the most important factor determining the tunneling current between small (similar to nm) ribbons. The quasi-one dimensional nature of graphene nanoribbons is shown to result in resonant tunneling.
Keywords: P1 Proceeding; Condensed Matter Theory (CMT)
|
“Modeling and tackling resistivity scaling in metal nanowires”. Moors K, Sorée B, Magnus W, International Conference on Simulation of Semiconductor Processes and Devices : [proceedings]
T2 –, International Conference on Simulation of Semiconductor Processes and, Devices (SISPAD), SEP 09-11, 2015, Washington, DC , 222 (2015)
Abstract: A self-consistent analytical solution of the multi-subband Boltzmann transport equation with collision term describing grain boundary and surface roughness scattering is presented to study the resistivity scaling in metal nanowires. The different scattering mechanisms and the influence of their statistical parameters are analyzed. Instead of a simple power law relating the height or width of a nanowire to its resistivity, the picture appears to be more complicated due to quantum-mechanical scattering and quantization effects, especially for surface roughness scattering.
Keywords: P1 Proceeding; Condensed Matter Theory (CMT)
|
“Analytic solution of Ando's surface roughness model with finite domain distribution functions”. Moors K, Sorée B, Magnus W, 18th International Workshop On Computational Electronics (iwce 2015) (2015)
Abstract: Ando's surface roughness model is applied to metallic nanowires and extended beyond small roughness size and infinite barrier limit approximations for the wavefunction overlaps, such as the Prange-Nee approximation. Accurate and fast simulations can still be performed without invoking these overlap approximations by averaging over roughness profiles using finite domain distribution functions to obtain an analytic solution for the scattering rates. The simulations indicate that overlap approximations, while predicting a resistivity that agrees more or less with our novel approach, poorly estimate the underlying scattering rates. All methods show that a momentum gap between left- and right-moving electrons at the Fermi level, surpassing a critical momentum gap, gives rise to a substantial decrease in resistivity.
Keywords: P1 Proceeding; Condensed Matter Theory (CMT)
|
“Improved source design for p-type tunnel field-effect transistors : towards truly complementary logic”. Verreck D, Verhulst AS, Sorée B, Collaert N, Mocuta A, Thean A, Groeseneken G, Applied physics letters 105, 243506 (2014). http://doi.org/10.1063/1.4904712
Abstract: Complementary logic based on tunnel field-effect transistors (TFETs) would drastically reduce power consumption thanks to the TFET's potential to obtain a sub-60 mV/dec subthreshold swing (SS). However, p-type TFETs typically do not meet the performance of n-TFETs for direct bandgap III-V configurations. The p-TFET SS stays well above 60 mV/dec, due to the low density of states in the conduction band. We therefore propose a source configuration in which a highly doped region is maintained only near the tunnel junction. In the remaining part of the source, the hot carriers in the exponential tail of the Fermi-Dirac distribution are blocked by reducing the doping degeneracy, either with a source section with a lower doping concentration or with a heterostructure. We apply this concept to n-p-i-p configurations consisting of In0.53Ga0.47As and an InP-InAs heterostructure. 15-band quantum mechanical simulations predict that the configurations with our source design can obtain sub-60 mV/dec SS, with an on-current comparable to the conventional source design. (C) 2014 AIP Publishing LLC.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 3.411
Times cited: 10
DOI: 10.1063/1.4904712
|
“Superior reliability of junctionless pFinFETs by reduced oxide electric field”. Toledano-Luque M, Matagne P, Sibaja-Hernandez A, Chiarella T, Ragnarsson L-A, Sorée B, Cho M, Mocuta A, Thean A, IEEE electron device letters 35, 1179 (2014). http://doi.org/10.1109/LED.2014.2361769
Abstract: Superior reliability of junctionless (JL) compared with inversion-mode field-effect transistors (FETs) is experimentally demonstrated on bulk FinFET wafers. The reduced negative bias temperature instability (NBTI) of JL pFETs outperforms the previously reported best NBTI reliability data obtained with Si channel devices and guarantees 10-year lifetime at typical operating voltages and high temperature. This behavior is understood through the reduced oxide electric field and lessened interaction between charge carriers and oxide traps during device operation. These findings encourage the investigation of JL devices with alternative channels as a promising alternative for 7-nm technology nodes meeting reliability targets.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 3.048
Times cited: 13
DOI: 10.1109/LED.2014.2361769
|
“Resistivity scaling and electron relaxation times in metallic nanowires”. Moors K, Sorée B, Tokei Z, Magnus W, Journal of applied physics 116, 063714 (2014). http://doi.org/10.1063/1.4892984
Abstract: We study the resistivity scaling in nanometer-sized metallic wires due to surface roughness and grain-boundaries, currently the main cause of electron scattering in nanoscaled interconnects. The resistivity has been obtained with the Boltzmann transport equation, adopting the relaxation time approximation of the distribution function and the effective mass approximation for the conducting electrons. The relaxation times are calculated exactly, using Fermi's golden rule, resulting in a correct relaxation time for every sub-band state contributing to the transport. In general, the relaxation time strongly depends on the sub-band state, something that remained unclear with the methods of previous work. The resistivity scaling is obtained for different roughness and grain-boundary properties, showing large differences in scaling behavior and relaxation times. Our model clearly indicates that the resistivity is dominated by grain-boundary scattering, easily surpassing the surface roughness contribution by a factor of 10. (C) 2014 AIP Publishing LLC.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 2.068
Times cited: 17
DOI: 10.1063/1.4892984
|
“Can p-channel tunnel field-effect transistors perform as good as n-channel?”.Verhulst AS, Verreck D, Pourghaderi MA, Van de Put M, Sorée B, Groeseneken G, Collaert N, Thean AV-Y, Applied physics letters 105, 043103 (2014). http://doi.org/10.1063/1.4891348
Abstract: We show that bulk semiconductor materials do not allow perfectly complementary p- and n-channel tunnel field-effect transistors (TFETs), due to the presence of a heavy-hole band. When tunneling in p-TFETs is oriented towards the gate-dielectric, field-induced quantum confinement results in a highest-energy subband which is heavy-hole like. In direct-bandgap IIIV materials, the most promising TFET materials, phonon-assisted tunneling to this subband degrades the subthreshold swing and leads to at least 10x smaller on-current than the desired ballistic on-current. This is demonstrated with quantum-mechanical predictions for p-TFETs with tunneling orthogonal to the gate, made out of InP, In0.53Ga0.47As, InAs, and a modified version of In0.53Ga0.47As with an artificially increased conduction-band density-of-states. We further show that even if the phonon-assisted current would be negligible, the build-up of a heavy-hole-based inversion layer prevents efficient ballistic tunneling, especially at low supply voltages. For p-TFET, a strongly confined n-i-p or n-p-i-p configuration is therefore recommended, as well as a tensily strained line-tunneling configuration. (C) 2014 AIP Publishing LLC.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 3.411
Times cited: 8
DOI: 10.1063/1.4891348
|
“InGaAs tunnel diodes for the calibration of semi-classical and quantum mechanical band-to-band tunneling models”. Smets Q, Verreck D, Verhulst AS, Rooyackers R, Merckling C, Van De Put M, Simoen E, Vandervorst W, Collaert N, Thean VY, Sorée B, Groeseneken G, Heyns MM;, Journal of applied physics 115, 184503 (2014). http://doi.org/10.1063/1.4875535
Abstract: Promising predictions are made for III-V tunnel-field-effect transistor (FET), but there is still uncertainty on the parameters used in the band-to-band tunneling models. Therefore, two simulators are calibrated in this paper; the first one uses a semi-classical tunneling model based on Kane's formalism, and the second one is a quantum mechanical simulator implemented with an envelope function formalism. The calibration is done for In0.53Ga0.47As using several p+/intrinsic/n+ diodes with different intrinsic region thicknesses. The dopant profile is determined by SIMS and capacitance-voltage measurements. Error bars are used based on statistical and systematic uncertainties in the measurement techniques. The obtained parameters are in close agreement with theoretically predicted values and validate the semi-classical and quantum mechanical models. Finally, the models are applied to predict the input characteristics of In0.53Ga0.47As n- and p-lineTFET, with the n-lineTFET showing competitive performance compared to MOSFET.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 2.068
Times cited: 34
DOI: 10.1063/1.4875535
|
“Quantum mechanical solver for confined heterostructure tunnel field-effect transistors”. Verreck D, Van de Put M, Sorée B, Verhulst AS, Magnus W, Vandenberghe WG, Collaert N, Thean A, Groeseneken G, Journal of applied physics 115, 053706 (2014). http://doi.org/10.1063/1.4864128
Abstract: Heterostructure tunnel field-effect transistors (HTFET) are promising candidates for low-power applications in future technology nodes, as they are predicted to offer high on-currents, combined with a sub-60 mV/dec subthreshold swing. However, the effects of important quantum mechanical phenomena like size confinement at the heterojunction are not well understood, due to the theoretical and computational difficulties in modeling realistic heterostructures. We therefore present a ballistic quantum transport formalism, combining a novel envelope function approach for semiconductor heterostructures with the multiband quantum transmitting boundary method, which we extend to 2D potentials. We demonstrate an implementation of a 2-band version of the formalism and apply it to study confinement in realistic heterostructure diodes and p-n-i-n HTFETs. For the diodes, both transmission probabilities and current densities are found to decrease with stronger confinement. For the p-n-i-n HTFETs, the improved gate control is found to counteract the deterioration due to confinement. (C) 2014 AIP Publishing LLC.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 2.068
Times cited: 15
DOI: 10.1063/1.4864128
|
“Tensile strained Ge tunnel field-effect transistors: k\cdot p material modeling and numerical device simulation”. Kao K-H, Verhulst AS, Van de Put M, Vandenberghe WG, Sorée B, Magnus W, De Meyer K, Journal of applied physics 115, 044505 (2014). http://doi.org/10.1063/1.4862806
Abstract: Group IV based tunnel field-effect transistors generally show lower on-current than III-V based devices because of the weaker phonon-assisted tunneling transitions in the group IV indirect bandgap materials. Direct tunneling in Ge, however, can be enhanced by strain engineering. In this work, we use a 30-band k.p method to calculate the band structure of biaxial tensile strained Ge and then extract the bandgaps and effective masses at Gamma and L symmetry points in k-space, from which the parameters for the direct and indirect band-to-band tunneling (BTBT) models are determined. While transitions from the heavy and light hole valence bands to the conduction band edge at the L point are always bridged by phonon scattering, we highlight a new finding that only the light-holelike valence band is strongly coupling to the conduction band at the Gamma point even in the presence of strain based on the 30-band k.p analysis. By utilizing a Technology Computer Aided Design simulator equipped with the calculated band-to-band tunneling BTBT models, the electrical characteristics of tensile strained Ge point and line tunneling devices are self-consistently computed considering multiple dynamic nonlocal tunnel paths. The influence of field-induced quantum confinement on the tunneling onset is included. Our simulation predicts that an on-current up to 160 (260) mu A/mu m can be achieved along with on/off ratio > 10(6) for V-DD = 0.5V by the n-type (p-type) line tunneling device made of 2.5% biaxial tensile strained Ge. (C) 2014 AIP Publishing LLC.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 2.068
Times cited: 26
DOI: 10.1063/1.4862806
|
“Spectral force approach to solve the time-dependent Wigner-Liouville equation”. Van de Put M, Thewissen M, Magnus W, Sorée B, Sellier JM, 2014 International Workshop On Computational Electronics (iwce) (2014)
Keywords: P1 Proceeding; Condensed Matter Theory (CMT)
|
“Perspective of tunnel-FET for future low-power technology nodes”. Verhulst AS, Verreck D, Smets Q, Kao K-H, Van de Put M, Rooyackers R, Sorée B, Vandooren A, De Meyer K, Groeseneken G, Heyns MM, Mocuta A, Collaert N, Thean AV-Y, 2014 Ieee International Electron Devices Meeting (iedm) (2014)
Keywords: P1 Proceeding; Condensed Matter Theory (CMT)
|
“Phonon-assisted Zener tunneling in a cylindrical nanowire transistor”. Carrillo-Nuñez H, Magnus W, Vandenberghe WG, Sorée B, Peeters FM, Journal of applied physics 113, 184507 (2013). http://doi.org/10.1063/1.4803715
Abstract: The tunneling current has been computed for a cylindrical nanowire tunneling field-effect transistor (TFET) with an all-round gate that covers the source region. Being the underlying mechanism, band-to-band tunneling, mediated by electron-phonon interaction, is pronouncedly affected by carrier confinement in the radial direction and, therefore, involves the self-consistent solution of the Schrodinger and Poisson equations. The latter has been accomplished by exploiting a non-linear variational principle within the framework of the modified local density approximation taking into account the nonparabolicity of both the valence band and conduction band in relatively thick wires. Moreover, while the effective-mass approximation might still provide a reasonable description of the conduction band in relatively thick wires, we have found that the nonparabolicity of the valence band needs to be included. As a major conclusion, it is observed that confinement effects in nanowire tunneling field-effect transistors have a stronger impact on the onset voltage of the tunneling current in comparison with planar TFETs. On the other hand, the value of the onset voltage is found to be overestimated when the valence band nonparabolicity is ignored. (C) 2013 AIP Publishing LLC.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 2.068
Times cited: 4
DOI: 10.1063/1.4803715
|
“Figure of merit for and identification of sub-60 mV/decade devices”. Vandenberghe WG, Verhulst AS, Sorée B, Magnus W, Groeseneken G, Smets Q, Heyns M, Fischetti MV, Applied physics letters 102, 013510 (2013). http://doi.org/10.1063/1.4773521
Abstract: A figure of merit I60 is proposed for sub-60 mV/decade devices as the highest current where the input characteristics exhibit a transition from sub- to super-60 mV/decade behavior. For sub-60 mV/decade devices to be competitive with metal-oxide-semiconductor field-effect devices, I60 has to be in the 1-10 μA/μm range. The best experimental tunnel field-effect transistors (TFETs) in the literature only have an I60 of 6×10-3 μA/μm but using theoretical simulations, we show that an I60 of up to 10 μA/μm should be attainable. It is proven that the Schottky barrier FET (SBFET) has a 60 mV/decade subthreshold swing limit while combining a SBFET and a TFET does improve performance.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 3.411
Times cited: 64
DOI: 10.1063/1.4773521
|
“Phonon-assisted Zener tunneling in a p-n diode silicon nanowire”. Carrillo-Nunez H, Magnus W, Vandenberghe WG, Sorée B, Peeters FM, Solid state electronics 79, 196 (2013). http://doi.org/10.1016/j.sse.2012.09.004
Abstract: The Zener tunneling current flowing through a biased, abrupt p-n junction embedded in a cylindrical silicon nanowire is calculated. As the band gap becomes indirect for sufficiently thick wires, Zener tunneling and its related transitions between the valence and conduction bands are mediated by short-wavelength phonons interacting with mobile electrons. Therefore, not only the high electric field governing the electrons in the space-charge region but also the transverse acoustic (TA) and transverse optical (TO) phonons have to be incorporated in the expression for the tunneling current. The latter is also affected by carrier confinement in the radial direction and therefore we have solved the Schrodinger and Poisson equations self-consistently within the effective mass approximation for both conduction and valence band electrons. We predict that the tunneling current exhibits a pronounced dependence on the wire radius, particularly in the high-bias regime. (C) 2012 Elsevier Ltd. All rights reserved.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 1.58
Times cited: 2
DOI: 10.1016/j.sse.2012.09.004
|
“Towards CMOS-compatible single-walled carbon nanotube resonators”. Pathangi H, Cherman V, Khaled A, Sorée B, Groeseneken G, Witvrouw A, Microelectronic engineering 107, 219 (2013). http://doi.org/10.1016/j.mee.2012.06.007
Abstract: We report a totally CMOS-compatible fabrication technique to assemble horizontally suspended single-walled carbon nanotube (SWCNT) resonators. Individual SWCNTs are assembled in parallel at multiple sites by a technique called dielectrophoresis. The mechanical resonance frequencies of the suspended SWCNTs are in the range of 2035 MHz as determined from the piezoresistive response of the resonators during electrostatic actuation. The resistance of the suspended SWCNT either remains unchanged or increases or decreases significantly as a function of the actuation frequency. This can be explained by the effect the nanotube chirality has on the piezoresistive gauge factor.
Keywords: A1 Journal article; Engineering sciences. Technology; Condensed Matter Theory (CMT)
Impact Factor: 1.806
Times cited: 6
DOI: 10.1016/j.mee.2012.06.007
|
“Optimization of gate-on-source-only tunnel FETs with counter-doped pockets”. Kao K-H, Verhulst AS, Vandenberghe WG, Sorée B, Magnus W, Leonelli D, Groeseneken G, De Meyer K, IEEE transactions on electron devices 59, 2070 (2012). http://doi.org/10.1109/TED.2012.2200489
Abstract: We investigate a promising tunnel FET configuration having a gate on the source only, which is simultaneously exhibiting a steeper subthreshold slope and a higher ON-current than the lateral tunneling configuration with a gate on the channel. Our analysis is performed based on a recently developed 2-D quantum-mechanical simulator calculating band-to-band tunneling and including quantum confinement (QC). It is shown that the two disadvantages of the structure, namely, the sensitivity to gate alignment and the physical oxide thickness, are mitigated by placing a counter-doped parallel pocket underneath the gate-source overlap. The pocket also significantly reduces the field-induced QC. The findings are illustrated with all-Si and all-Ge gate-on-source-only tunnel field-effect transistor simulations.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 2.605
Times cited: 72
DOI: 10.1109/TED.2012.2200489
|
“A model determining optimal doping concentration and material's band gap of tunnel field-effect transistors”. Vandenberghe WG, Verhulst AS, Kao K-H, De Meyer K, Sorée B, Magnus W, Groeseneken G, Applied physics letters 100, 193509 (2012). http://doi.org/10.1063/1.4714544
Abstract: We develop a model for the tunnel field-effect transistor (TFET) based on the Wentzel-Kramer-Brillouin approximation which improves over existing semi-classical models employing generation rates. We hereby introduce the concept of a characteristic tunneling length in direct semiconductors. Based on the model, we show that a limited density of states results in an optimal doping concentration as well as an optimal material's band gap to obtain the highest TFET on-current at a given supply voltage. The observed optimal-doping trend is confirmed by 2-dimensional quantum-mechanical simulations for silicon and germanium. (C) 2012 American Institute of Physics. [http://dx.doi.org/10.1063/1.4714544]
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 3.411
Times cited: 25
DOI: 10.1063/1.4714544
|
“Modeling the impact of junction angles in tunnel field-effect transistors”. Kao K-H, Verhulst AS, Vandenberghe WG, Sorée B, Groeseneken G, De Meyer K, Solid state electronics 69, 31 (2012). http://doi.org/10.1016/j.sse.2011.10.032
Abstract: We develop an analytical model for a tunnel field-effect transistor (TFET) with a tilted source junction angle. The tunnel current is derived by using circular tunnel paths along the electric field. The analytical model predicts that a smaller junction angle improves the TFET performance, which is supported by device simulations. An analysis is also made based on straight tunnel paths and tunnel paths corresponding to the trajectory of a classical particle. In all the aforementioned cases, the same conclusions are obtained. A TFET configuration with an encroaching polygon source junction is studied to analyze the junction angle dependence at the smallest junction angles. The improvement of the subthreshold swing (SS) with decreasing junction angle can be achieved by using thinner effective oxide thickness, smaller band gap material and longer encroaching length of the encroaching junction. A TFET with a smaller junction angle on the source side also has an innate immunity against the degradation of the fringing field from the gate electrode via a high-k spacer. A large junction angle on the drain side can suppress the unwanted ambipolar current of TFETs. (c) 2011 Elsevier Ltd. All rights reserved.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 1.58
Times cited: 9
DOI: 10.1016/j.sse.2011.10.032
|
“Direct and indirect band-to-band tunneling in germanium-based TFETs”. Kao K-H, Verhulst AS, Vandenberghe WG, Sorée B, Groeseneken G, De Meyer K, IEEE transactions on electron devices 59, 292 (2012). http://doi.org/10.1109/TED.2011.2175228
Abstract: Germanium is a widely used material for tunnel FETs because of its small band gap and compatibility with silicon. Typically, only the indirect band gap of Ge at 0.66 eV is considered. However, direct band-to-band tunneling (BTBT) in Ge should be included in tunnel FET modeling and simulations since the energy difference between the Ge conduction band edges at the L and G valleys is only 0.14 eV at room temperature. In this paper, we theoretically calculate the parameters A and B of Kane's direct and indirect BTBT models at different tunneling directions ([100], [110], and [111]) for Si, Ge and unstrained Si1-xGex. We highlight how the direct BTBT component becomes more important as the Ge mole fraction increases. The calculation of the band-to-band generation rate in the uniform electric field limit reveals that direct tunneling always dominates over indirect tunneling in Ge. The impact of the direct transition in Ge on the performance of two realistic tunnel field-effect transistor configurations is illustrated with TCAD simulations. The influence of field-induced quantum confinement is included in the analysis based on a back-of-the-envelope calculation.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 2.605
Times cited: 212
DOI: 10.1109/TED.2011.2175228
|
“Quantum simulations of electrostatics in Si cylindrical junctionless nanowire nFETs and pFETs with a homogeneous channel including strain and arbitrary crystallographic orientations”. Pham A-T, Sorée B, Magnus W, Jungemann C, Meinerzhagen B, Pourtois G, Solid state electronics 71, 30 (2012). http://doi.org/10.1016/j.sse.2011.10.016
Abstract: Simulation results of electrostatics in Si cylindrical junctionless nanowire transistors with a homogenous channel are presented. Junctionless transistors including strain and arbitrary crystallographic orientations are studied. Size quantization effects are simulated by self-consistent solutions of the Poisson and Schrodinger equations. The 6 x 6 k.p method is employed for the calculation of the valence subband structure in a junctionless nanowire pFET. The influence of stress/strain and crystallographic channel orientation on to the electrostatics in terms of subband structure, charge density, and C-V curve is systematically studied. (C) 2011 Elsevier Ltd. All rights reserved.
Keywords: A1 Journal article; Condensed Matter Theory (CMT); Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Impact Factor: 1.58
Times cited: 2
DOI: 10.1016/j.sse.2011.10.016
|
“Low-field mobility in ultrathin silicon nanowire junctionless transistors”. Sorée B, Magnus W, Vandenberghe W, Applied physics letters 99, 233509 (2011). http://doi.org/10.1063/1.3669509
Abstract: We theoretically investigate the phonon, surface roughness and ionized impurity limited low-field mobility of ultrathin silicon n-type nanowire junctionless transistors in the long channel approximation with wire radii ranging from 2 to 5 nm, as function of gate voltage. We show that surface roughness scattering is negligible as long as the wire radius is not too small and ionized impurity scattering is the dominant scattering mechanism. We also show that there exists an optimal radius where the ionized impurity limited mobility exhibits a maximum.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 3.411
Times cited: 20
DOI: 10.1063/1.3669509
|
“Comparison of strained SiGe heterostructure-on-insulator (0 0 1) and (1 1 0) PMOSFETs : CV characteristics, mobility, and ON current”. Pham A-T, Zhao Q-T, Jungemann C, Meinerzhagen B, Mantl S, Sorée B, Pourtois G, Solid state electronics 65-66, 64 (2011). http://doi.org/10.1016/j.sse.2011.06.021
Abstract: Strained SiGe heterostructure-on-insulator (0 0 1) and (1 1 0) PMOSFETs are investigated including important aspects like CV characteristics, mobility, and ON current. The simulations are based on the self-consistent solution of 6 × 6 k · p Schrödinger Equation, multi subband Boltzmann Transport Equation and Poisson Equation, and capture size quantization, strain, crystallographic orientation, and SiGe alloy effects on a solid physical basis. The simulation results are validated by comparison with different experimental data sources. The simulation results show that the strained SiGe HOI PMOSFET with (1 1 0) surface orientation has a higher gate capacitance and a much higher mobility and ON current compared to a similar device with the traditional (0 0 1) surface orientation.
Keywords: A1 Journal article; Condensed Matter Theory (CMT); Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Impact Factor: 1.58
Times cited: 2
DOI: 10.1016/j.sse.2011.06.021
|
“Generalized phonon-assisted Zener tunneling in indirect semiconductors with non-uniform electric fields : a rigorous approach”. Vandenberghe W, Sorée B, Magnus W, Fischetti MV, Journal of applied physics 109, 124503 (2011). http://doi.org/10.1063/1.3595672
Abstract: A general framework to calculate the Zener current in an indirect semiconductor with an externally applied potential is provided. Assuming a parabolic valence and conduction band dispersion, the semiconductor is in equilibrium in the presence of the external field as long as the electron-phonon interaction is absent. The linear response to the electron-phonon interaction results in a non-equilibrium system. The Zener tunneling current is calculated from the number of electrons making the transition from valence to conduction band per unit time. A convenient expression based on the single particle spectral functions is provided, enabling the evaluation of the Zener tunneling current under any three-dimensional potential profile. For a one-dimensional potential profile an analytical expression is obtained for the current in a bulk semiconductor, a semiconductor under uniform field, and a semiconductor under a non-uniform field using the WKB (Wentzel-Kramers-Brillouin) approximation. The obtained results agree with the Kane result in the low field limit. A numerical example for abrupt p-n diodes with different doping concentrations is given, from which it can be seen that the uniform field model is a better approximation than the WKB model, but a direct numerical treatment is required for low bias conditions.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 2.068
Times cited: 41
DOI: 10.1063/1.3595672
|