|
|
“Comparative study of structural properties and photoluminescence in InGaN layers with a high In content”. Vantomme A, Wu MF, Hogg S, van Landuyt J, et al, Internet journal of nitride semiconductor research
T2 –, Symposium on GaN and Related Alloys Held at the MRS Fall Meeting, NOV 29-DEC 03, 1999, BOSTON, MASSACHUSETTS 5, art. no.-W11.38 (2000)
Abstract: Rutherford backscattering and channeling spectrometry (RBS), photoluminescence (PL) spectroscopy and transmission electron microscopy (TEM) have been used to investigate macroscopic and microscopic segregation in MOCVD grown InGaN layers. The PL peak energy and In content (measured by RES) were mapped at a large number of distinct points on the samples. An indium concentration of 40%, the highest measured in this work, corresponds to a PL peak of 710 nn strongly suggesting that the light-emitting regions of the sample me very indium-rich compared to the average measured by RES. Cross-sectional TEM observations show distinctive layering of the InGaN films. The TEM study further reveals that these layers consist of amorphous pyramidal contrast features with sizes of order 10 nm The composition of these specific contrast features is shown to be In-rich compared to the nitride matrix.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
|
|
|
|
“Atomic structure of alloys close to phase transitions”. Van Tendeloo G, Schryvers D, Nucleation and growth processes in materials 580, 283 (2000)
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
|
|
|
|
“TEM of nanostructured materials”. Van Tendeloo G, Pauwels B, Geuens P, Lebedev O, , 3 (2000)
Keywords: P3 Proceeding; Electron microscopy for materials research (EMAT)
Times cited: 31
|
|
|
|
“Identification of new superconducting compounds by electron microscopy”. Van Tendeloo G, Krekels T Cambridge University Press, Cambridge, page 161 (2000).
Keywords: H3 Book chapter; Electron microscopy for materials research (EMAT)
|
|
|
|
“Electron microscopy of fullerenes and related materials”. Van Tendeloo G, Amelinckx S Wiley-VCH, Weinheim, page 353 (2000).
Keywords: H3 Book chapter; Electron microscopy for materials research (EMAT)
|
|
|
|
“TEM of phase transitions in tridymite and cristobalite based materials”. Van Tendeloo G, Microscoy and microanalysis 6 (2000)
Keywords: A3 Journal article; Electron microscopy for materials research (EMAT)
|
|
|
|
“Defect induced thickness growth in silver chloride (111) tabular crystals: a TEM study”. Van Renterghem W, Schryvers D, van Landuyt J, Bollen D, Van Roost C, De Keyzer RB, , 38 (2000)
Abstract: Defects in AgG tabular crystals with {111} surfaces are characterised by transmission electron microscopy (TEM) and their influence on the growth process is discussed. In the tabular crystals, twins parallel to the tabular face as well as dislocations along different directions are observed. The twins induce the tabular growth, while the dislocations do not influence the morphology. In 10 to 30% of the crystals that have been characterised, thickness growth is observed and it is shown that in all cases twins on other planes than the tabular ones are present. Two configurations occur more frequently and are analysed in detail. For the first group, twins parallel to the tabular face as well as a microtwin along a non-parallel {111} plane and ending inside the crystal are present. In the crystals of the second group only one extra non-parallel twin occurs giving rise to a bicrystal built up by a tetrahedral shaped part and a flat triangular or trapezoidal part. More complex twin configurations give rise to various, less characteristic morphologies.
Keywords: P1 Proceeding; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
|
|
|
|
“The influence of the precipitation method on defect formation in multishell AgBrI (111) tabular crystals”. Van Renterghem W, Karthauser S, Schryvers D, van Landuyt J, De Keyzer R, Van Roost C, , 167 (2000)
Abstract: Multishell tabular grains have a higher speed than pure AgBr tabular grains. Usually the shells differ in size and iodide content, but also the precipitation method for the iodide containing shells has an influence on the iodide incorporation. A TEM investigation was performed to determine the defect structure of multishell AgBr (111) tabular crystals containing a shell with a low iodide concentration and one with a high iodide concentration. The twins that induce tabular growth and stacking fault contrast in the region of the iodide shells have been observed, similar to previously studied AgBr/Ag(Br,I) coreshell crystals. Moreover in some of the crystals dislocations have been observed, sometimes even an entire network. The number of dislocations formed varies for the different methods of iodide addition. Also variations in average thickness between the different iodide addition methods have been observed. A higher number of dislocations and thicker crystals point towards a higher local concentration of iodide. These observations allow deciding which iodide incorporation method is most useful for a preferred dislocation pattern.
Keywords: P1 Proceeding; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
|
|
|
|
“Influence of oxygen content on the charge-ordering process in La0.5Ca0.5MnO3”. Schuddinck W, Van Tendeloo G, Martin C, Hervieu M, Raveau B s.l., page 199 (2000).
Keywords: H3 Book chapter; Electron microscopy for materials research (EMAT)
|
|
|
|
“Martensitic transformations studied on nano- and microscopic length scales”. Schryvers D, Boullay P, Potapov P, Satto C, Festkörperprobleme 40, 375 (2000)
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
|
|
|
|
“Epitaxial growth of \beta-SiC on ion-beam synthesized \beta-SiC : structural characterization”. Romano-Rodriguez A, Perez-Rodriguez A, Serre C, van Landuyt J, et al, Materials science forum
T2 –, International Conference on Silicon Carbide and Related Materials, OCT 10-15, 1999, RES TRIANGLE PK, NORTH CAROLINA 338-3, 309 (2000)
Abstract: In this work we present for the first time, to our knowledge, the CVD epitaxial growth of beta -SiC using an ion beam synthesized (IBS) beta -SiC layer as seed, which has been formed by multiple implantation into Si wafers at 500 degreesC. The ion beam synthesized continuous layer is constituted by beta -SiC nanocrystals that are well oriented relative to the silicon substrate. Comparison of the epitaxial growth on these samples with that on silicon test samples, both on and off-axis, is performed. The results show that the epitaxial growth can be achieved on the IBS samples without the need of the carbonization step and that the structural quality of the CVD layer is comparable to that obtained on a carbonized silicon sample. Improvement of the quality of the deposited layer is proposed.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Times cited: 2
|
|
|
|
“Structural properties of Au clusters on MgO”. Pauwels B, Van Tendeloo G, Bouwen W, Kuhn LT, Lievens P, , 383 (2000)
Keywords: P3 Proceeding; Electron microscopy for materials research (EMAT)
|
|
|
|
“Strained La1-xSrxMnO3 (x = 0.1 – 0.3) thin films studied by HREM”. Lebedev OI, Van Tendeloo G, Amelinckx S s.l., page 201 (2000).
Keywords: H3 Book chapter; Electron microscopy for materials research (EMAT)
|
|
|
|
“Granular films assembled of CoN, CrM and mixtures of CoN and CrM clusters: structure and electron transport properties”. Kuhn LT, Vanhoutte F, Cannaerts M, Neukermans S, Verschoren G, Bouwen W, van Haesendonck C, Lievens P, Silverans RE, Pauwels B, Van Tendeloo G, (2000)
Keywords: P3 Proceeding; Electron microscopy for materials research (EMAT)
|
|
|
|
“Aerosol synthesis of fullerene nanocrystals in controlled flow reactor conditions”. Joutsensaari J, Ahonen PP, Kauppinen EI, Brown DP, Lehtinen KEJ, Jokiniemi JK, Pauwels B, Van Tendeloo G, Journal of nanoparticle research 2, 53 (2000)
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 2.02
Times cited: 5
|
|
|
|
“Charge ordering and phase transitions in perovskite manganites: correlation with CMR properties”. Hervieu M, Martin C, Van Tendeloo G, Mercey B, Maignan A, Jirak Z, Raveau B s.l., page 179 (2000).
Keywords: H3 Book chapter; Electron microscopy for materials research (EMAT)
|
|
|
|
“Structural changes in fluorinated T{'} and T* phases”. Hadermann J, Abakumov AM, Lebedev OI, Antipov EV, Van Tendeloo G, , 193 (2000)
Keywords: P3 Proceeding; Electron microscopy for materials research (EMAT)
|
|
|
|
“Gold particles supported on TiO2”. Giorgio S, Henry CR, Pauwels B, Van Tendeloo G, , 369 (2000)
Keywords: P3 Proceeding; Electron microscopy for materials research (EMAT)
|
|
|
|
“Accurate measurements of atomic displacements in La0.9Sr0.1MnO3 thin films grown on a SrTiO3 substrate”. Geuens P, Lebedev OI, van Dyck D, Van Tendeloo G s.l., page 1133 (2000).
Keywords: H3 Book chapter; Electron microscopy for materials research (EMAT); Vision lab
|
|
|
|
“Electron microscopy and X-ray structural investigations of incommensurate spin-ladder Sr4.1Ca4.7Bi0.3Cu17O29 single crystals”. Dluzewski P, Pietraszko A, Kozlowski M, Szczepanska A, Gorecka J, Baran M, Leonyuk L, Babonas GJ, Lebedev OI, Szymczak R, Acta physica Polonica: A: general physics, solid state physics, applied physics 98, 729 (2000)
Abstract: Transmission electron microscopy and X-ray diffraction proved chain/ladder incommensurate single crystal structure of investigated samples. The incommensurate ratio was determined from the X-ray and electron diffraction being equal to 0.704. Diffuse scattering intensities localised on the planes perpendicular to the c*-axis and passing through the spots originating from the periodicity of chain sublattice were detected. High-angle grain boundary or twinning formed by rotation of 33.3 degrees around [100] direction was observed. High-resolution electron microscopy images revealed the stacking faults in ac planes.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 0.469
|
|
|
|
“Microstructure and phase transitions in Pb(Sc0.5Ta0.5)O3”. Lemmens H, Richard O, Van Tendeloo G, Bismayer U, Journal of electron microscopy 48, 843 (1999). http://doi.org/10.1093/oxfordjournals.jmicro.a023756
Abstract: The microstructure and phase transitions in the perovskite-based ferroelectric lead scandium tantalate, Pb(Sc0.5Ta0.5)O-3 have been investigated by transmission electron microscopy. The effects of ordering of Sc and Ta cations are apparent in reciprocal space as well as in direct space images. High-resolution observations allow direct structure imaging of the domain structure. The structure of the low temperature ferroelectric phase is studied by selected area electron diffraction (SAED) and electron microdiffraction. The relaxer behaviour of this paraelectric-ferroelectric transition is displayed by diffuse intensities in the SAED patterns at temperatures around the Curie point.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 0.9
Times cited: 7
DOI: 10.1093/oxfordjournals.jmicro.a023756
|
|
|
|
“Microstructure of tough polycrystalline natural diamond”. Chen JH, Van Tendeloo G, Journal of electron microscopy 48, 121 (1999). http://doi.org/10.1093/oxfordjournals.jmicro.a023658
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 0.9
Times cited: 9
DOI: 10.1093/oxfordjournals.jmicro.a023658
|
|
|
|
“Preparation of nanocrystalline titania powder via aerosol pyrolysis of titanium tetrabutoxide”. Ahonen PP, Kauppinen EI, Joubert JC, Deschanvres JL, Van Tendeloo G, Journal of materials research 14, 3938 (1999). http://doi.org/10.1557/JMR.1999.0533
Abstract: Nanocrystalline titanium dioxide was prepared via aerosol pyrolysis of titanium alkoxide precursor at 200-580 degrees C in air and in nitrogen atmospheres. Powders were characterized by x-ray diffraction, thermogravimetric analysis, Brunauer-Emmett-Teller analysis, scanning electron microscopy, transmission electron microscopy, energy dispersive spectroscopy, x-ray fluorescence, Raman and infrared spectroscopy, and Berner-type low-pressure impactor. The anatase phase transition was initiated at 500 degrees C in nitrogen and at 580 degrees C in air. Under other conditions amorphous powders were observed and transformed to nanocrystalline TiO2 via thermal postannealing. In air, smooth and spherical particles with 2-4-mu m diameter were formed with an as-expected tendency to convert to rutile in the thermal postannealings. In nitrogen, a fraction of the titanium tetrabutoxide precursor evaporated and formed ultrafine particles via the gas-to-particle conversion. At 500 degrees C thermally stable anatase phase was formed in nitrogen. A specific surface area as high as 280 m(2) g(-1) was observed for an as-prepared powder.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 1.673
Times cited: 38
DOI: 10.1557/JMR.1999.0533
|
|
|
|
“Electron microscopy investigation of ternary \gamma-brass-type precipitation in a Ni39.6Mn47.5Ti12.9 alloy”. Seo JW, Schryvers D, Vermeulen W, Richard O, Potapov P, Philosophical magazine: A: physics of condensed matter: defects and mechanical properties 79, 1279 (1999). http://doi.org/10.1080/01418619908210361
Abstract: Homogenized Ni39.6Mn47.5T12.9 material was investigated by different electron microscopy techniques. Apart from the martensite precursor distortions typical for B2 phase alloys undergoing a thermoelastic martensitic transformation upon cooling, coherent dodecahedron-shaped precipitates with sizes between 20 and 100 nm and faceted by lozenge shapes of {110}-type planes are observed. Selected-area and microdiffraction patterns reveal an overall unit cell with a size of 3 x 3 x 3 units of the bcc lattice of the matrix and a body-centred symmetry without screw axes. Finally a ternary gamma-brass-type atomic structure of space group 14(3) over bar m is suggested for these precipitates in accordance with the obtained symmetry constraints, the energy-dispersive X-ray measurements and high-resolution transmission electron microscopy images. This is the first time this type of structure is found in an alloy completely consisting of transition-metal elements.
Keywords: A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT); Laboratory Experimental Medicine and Pediatrics (LEMP)
Times cited: 3
DOI: 10.1080/01418619908210361
|
|
|
|
“A study of the domain structure of epitaxial (La-Ca)MnO3 films by high-resolution transmission electron microscopy”. Lebedev OI, Van Tendeloo G, Abakumov AM, Amelinckx S, Leibold B, Habermeier H-U, Philosophical magazine: A: physics of condensed matter: defects and mechanical properties 79, 1461 (1999). http://doi.org/10.1080/01418619908210372
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Times cited: 27
DOI: 10.1080/01418619908210372
|
|
|
|
“A homologous series Pb2n+1Nb2n-1O7n-1 studied by electron microscopy”. Leroux C, Badeche T, Nihoul G, Richard O, Van Tendeloo G, European physical journal: applied physics 7, 33 (1999). http://doi.org/10.1051/epjap:1999196
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 0.684
Times cited: 4
DOI: 10.1051/epjap:1999196
|
|
|
|
“Nanohardness and structure of nitrogen implanted SixAly coatings post-implanted with oxygen”. Jacobs M, Bodart F, Terwagne G, Schryvers D, Poulet A, Nuclear instruments and methods in physics research: B: beam interactions with materials and atoms 147, 231 (1999). http://doi.org/10.1016/S0168-583X(98)00535-7
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 1.109
Times cited: 3
DOI: 10.1016/S0168-583X(98)00535-7
|
|
|
|
“Structural transformations in the fluorinated T* phase”. Hadermann J, Abakumov AM, Lebedev OI, Van Tendeloo G, Rozova MG, Shpanchenko RV, Pavljuk BP, Kopnin EM, Antipov EV, Journal of solid state chemistry 147, 647 (1999). http://doi.org/10.1006/jssc.1999.8438
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 2.299
Times cited: 8
DOI: 10.1006/jssc.1999.8438
|
|
|
|
“Anion ordering in fluorinated La2CuO4”. Abakumov AM, Hadermann J, Van Tendeloo G, Shpanchenko RV, Oleinikov PN, Antipov EV, Journal of solid state chemistry 142, 311 (1999). http://doi.org/10.1006/jssc.1998.8064
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 2.299
Times cited: 20
DOI: 10.1006/jssc.1998.8064
|
|
|
|
“Structural determination of the charge ordering process in Nd0.5Ca0.5Mn1-xCrxO3 manganites”. Schuddinck W, Van Tendeloo G, Barnabé, A, Hervieu M, Raveau B, Journal of solid state chemistry 148, 333 (1999). http://doi.org/10.1006/jssc.1999.8457
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 2.299
Times cited: 12
DOI: 10.1006/jssc.1999.8457
|
|
