Abstract: Phenols are considered as toxic pollutants and their discharge into the environment by industries is regulated by a concentration limit. As these limits are in the low mg L−1 to µg L−1-range, sensitive methods are necessary to detect these phenols. Here, aqueous industrial phenolic samples throughout a cleaning process were analyzed by two novel electrochemical sensors. Both the photoelectrochemical (PEC) sensor and the square wave voltammetric (SWV) sensor could successfully follow the decrease of the concentration of phenols along the industrial cleaning process. The discharge sample (μg L−1) could only be analyzed by the PEC sensor and not by the SWV sensor, as the phenolic concentration was close to the LOD of the latter. With HPLC-diode array detector (DAD) measurements, classical phenols such as phenol (PHOH), hydroquinone, resorcinol and o-cresol could be identified in the industrial samples, and their presence could be linked to the electrochemical responses. At last, the performance of the PEC and SWV sensors were compared with commercial colorimetric and chemical oxygen demand (COD) test kits. This comparison demonstrated the high sensitivity of the PEC sensor in the μg L−1 concentrated phenolic samples. Together with the identification of the redox peaks through HPLC-DAD analysis, the SWV sensor can be a powerful tool in the qualitative analysis of mg L−1 concentrated phenolic samples due to its speed, simplicity and absence of laborious sample pre-treatment steps.

Abstract: The high toxicity, endocrine-disrupting effects and low (bio)degradability commonly attributed to phenolic compounds have promoted their recognition as priority toxic pollutants. For this reason, the monitoring of these compounds in industrial, domestic and agricultural streams is crucial to prevent and decrease their toxicity in our daily life. To confront this relevant environmental issue, we propose the use of a combi-electrosensor which combines singlet oxygen (1O2)-based photoelectrochemistry (PEC) with square wave voltammetry (SWV). The high sensitivity of the PEC sensor (being a faster alternative for traditional COD measurements) ensures the detection of nmol L−1 levels of phenolic compounds while the SWV measurements (being faster than the color test kits) allow the differentiation between phenolic compounds. Herein, we report on the development of such a combi-electrosensor for the sensitive and selective detection of phenol (PHOH) in the presence of related phenolic compounds such as hydroquinone (HQ), bisphenol A (BPA), resorcinol (RC) and catechol (CC). The PEC sensor was able to determine the concentration of PHOH in spiked river samples containing only PHOH with a recovery between 96% and 111%. The SWV measurements elucidated the presence of PHOH, HQ and CC in the spiked samples containing multiple phenol compounds. Finally, the practicality of the combi-electrosensor set-up with a dual SPE containing two working electrodes and shared reference and counter electrodes was demonstrated. As a result, the combination of the two techniques is a powerful and valuable tool in the analysis of phenolic samples, since each technique improves the general performance by overcoming the inherent drawbacks that they display independently.

Abstract: Phenolic compounds can be found everywhere in our daily lives but exhibit high toxicity, low (bio)degradability and hormone-disrupting effects when they are released in the environment. It is for this reason imperative to develop detection strategies for these pollutants. A promising approach involves the use of a photoelectrochemical (PEC) sensor. In this sensor, a photosensitiser (PS) type II, which generates 1O2 under illumination, is used to oxidise phenolic compounds present in the sample. The oxidised phenols are reduced at the electrode surface leading to the generation of an electrocatalytic redox cycle. In this thesis, an in-depth understanding, through the identification of the reactive oxygen species (ROS) in the PEC sensing mechanism, is obtained. The detection strategy is optimised by choosing the PS with the highest 1O2 production and by optimising the detection parameters so that the PEC sensor can be successfully applied for the detection of phenols in industrial samples. First, it was determined that the use of highly fluorinated zinc phthalocyanine derivatives, F52PcZn and F64PcZn, as photocatalysts was optimal for the sensing of phenol due to their high 1O2 production and improved single-site isolation. However, next to 1O2, it was shown that the ROS O2•- and H2O2 were also generated in the PEC sensor. Their contribution to the photocurrent response was studied by rotating disk electrode measurements in function of the pH and applied potential. After this, the PEC detection strategy was optimised in terms of pH and applied potential for the detection of doxycycline, cefadroxil, and phenol. It was found that the use of alkaline pH-levels led to nmol L-1-level detection limits. The combination with square wave voltammetry (SWV) was, also, proposed to allow the quantification and identification of phenolic compounds in a specific sample. At last, the developed PEC and SWV sensors were applied for the measurement of phenolic compounds in industrial water samples. The PEC sensor could follow the decrease of the phenolic concentration throughout the wastewater treatment process while the SWV sensor provided the electrochemical fingerprints of these samples. The thesis concluded that the use of the PEC sensor was advantageous in the measurement of lower concentrated phenolic samples due to its high sensitivity and fast measurement time in comparison to commercial test kits.

Abstract: The World Health Organization (WHO) model “List of Essential Medicines” includes among indispensable medicines antibacterials and pain and migraine relievers. Monitoring their concentration in the environment, while challenging, is important in the context of antibiotic resistance as well as their production of highly toxic compounds via hydrolysis. Traditional detection methods such as high-performance liquid chromatography (HPLC) or LC combined with tandem mass spectrometry or UV-vis spectroscopy are time-consuming, have a high cost, require skilled operators and are difficult to adapt for field operations. In contrast, (electrochemical) sensors have elicited interest because of their rapid response, high selectivity, and sensitivity as well as potential for on-site detection. Previously, we reported a novel sensor system based on a type II photosensitizer, which combines the advantages of enzymatic sensors (high sensitivity) and photoelectrochemical sensors (easy baseline subtraction). Under red-light illumination, the photosensitizer produces singlet oxygen which oxidizes phenolic compounds present in the sample. The subsequent reduction of the oxidized phenolic compounds at the electrode surface gives rise to a quantifiable photocurrent and leads to the generation of a redox cycle. Herein we report the optimization in terms of pH and applied potential of the photoelectrochemical detection of the hydrolysis product of paracetamol, i.e., 4-aminophenol (4-AP), and two antibacterials, namely, cefadroxil (CFD, beta-lactam antibiotic) and doxycycline (DXC, tetracycline antibiotic). The optimized conditions resulted in a detection limit of 0.2 mu mol L-1 for DXC, but in a 10 times higher sensitivity, 20 nmol L-1, for CFD. An even higher sensitivity, 7 nmol L-1, was noted for 4-AP.