| Records |
| Author |
Marteleur, M.; Idrissi, H.; Amin-Ahmadi, B.; Prima, F.; Schryvers, D.; Jacques, P.J. |
| Title |
On the nucleation mechanism of {112} < 111 > mechanical twins in as-quenched beta metastable Ti-12 wt.% Mo alloy |
Type |
A1 Journal article |
Year  |
2019 |
Publication |
Materialia |
Abbreviated Journal |
|
| Volume |
7 |
Issue |
|
Pages |
Unsp 100418 |
| Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
| Abstract |
Recently developed beta-metastable Ti grades take advantage of the simultaneous activation of TRIP and TWIP effects for enhancing their work hardening rate. However, the role of each plasticity mechanism on the macroscopic mechanical response is still unclear. In this work, the nucleation mechanism of the first activated plasticity mechanism, namely {112} < 111 > twinning, was investigated. Firstly, post-mortem TEM analysis showed that twins nucleate on pre-existing microstructural defects such as thermal jogs with the zonal dislocation mechanism. The precipitation of the omega phase on twin boundaries has been observed, as well as the emission of numerous dislocations from super-jogs present in these twin boundaries. It is also shown that {112} < 111 > twins act as effective dislocation sources for the subsequent plasticity mechanisms such as beta -> alpha '' martensitic transformation and {332} < 111 > twinning. Secondly, in situ TEM tensile testing of the investigated Ti grade highlighted the primary role of the initial defect configuration present in the microstructure. It is shown that twins cannot nucleate without the presence of specific defects allowing the triggering of the dislocation decomposition needed for the twinning mechanism highlighted in investigated bulk samples. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000537131000052 |
Publication Date |
2019-07-31 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
2589-1529 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
|
Times cited |
|
Open Access |
|
| Notes |
|
Approved |
no |
| Call Number |
UA @ admin @ c:irua:170326 |
Serial |
6875 |
| Permanent link to this record |
| |
|
| |
| Author |
Lumbeeck, G.; Idrissi, H.; Amin-Ahmadi, B.; Favache, A.; Delmelle, R.; Samaee, V.; Proost, J.; Pardoen, T.; Schryvers, D. |
| Title |
Effect of hydriding induced defects on the small-scale plasticity mechanisms in nanocrystalline palladium thin films |
Type |
A1 Journal Article |
| Year |
2018 |
Publication |
Journal Of Applied Physics |
Abbreviated Journal |
J Appl Phys |
| Volume |
124 |
Issue |
22 |
Pages |
225105 |
| Keywords |
A1 Journal Article; Electron Microscopy for Materials Science (EMAT) ; |
| Abstract |
Nanoindentation tests performed on nanocrystalline palladium films subjected to hydriding/dehydriding cycles demonstrate a significant softening when compared to the as-received material. The origin of this softening is unraveled by combining in situ TEM nanomechanical testing with automated crystal orientation mapping in TEM and high resolution TEM. The softening is attributed to the presence of a high density of stacking faults and of Shockley partial dislocations after hydrogen loading. The hydrogen induced defects affect the elementary plasticity mechanisms and the mechanical response by acting as preferential sites for twinning/detwinning during deformation. These results are analyzed and compared to previous experimental and simulation works in the literature. This study provides new insights into the effect of hydrogen on the atomistic deformation and cracking mechanisms as well as on the mechanical properties of nanocrystalline thin films and membranes. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000453254000025 |
Publication Date |
2018-12-14 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
0021-8979 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
2.068 |
Times cited |
2 |
Open Access |
Not_Open_Access |
| Notes |
This work was supported by the Hercules Foundation under Grant No. AUHA13009, the Flemish Research Fund (FWO) under Grant No. G.0365.15N, and the Flemish Strategic Initiative for Materials (SIM) under the project InterPoCo. Dr. H. Idrissi is mandated by the Belgian National Fund for Scientific Research (FSR-FNRS). We would like to thank Dr. Hadi Pirgazi from UGent for his technical support to process the ACOM data in the OIM Analysis software. |
Approved |
Most recent IF: 2.068 |
| Call Number |
EMAT @ emat @c:irua:155742 |
Serial |
5135 |
| Permanent link to this record |
| |
|
| |
| Author |
Du, C.; Hoefnagels, J.P.M.; Kolling, S.; Geers, M.G.D.; Sietsma, J.; Petrov, R.; Bliznuk, V.; Koenraad, P.M.; Schryvers, D.; Amin-Ahmadi, B. |
| Title |
Martensite crystallography and chemistry in dual phase and fully martensitic steels |
Type |
A1 Journal article |
| Year |
2018 |
Publication |
Materials characterization |
Abbreviated Journal |
Mater Charact |
| Volume |
139 |
Issue |
|
Pages |
411-420 |
| Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
| Abstract |
Lath martensite is important in industry because it is the key strengthening component in many advanced high strength steels. The study of crystallography and chemistry of lath martensite is extensive in the literature, however, mostly based on fully martensitic steels. In this work, lath martensite in dual phase steels is investigated with a focus on the substructure identification of the martensite islands and microstructural bands using electron backscattered diffraction, and on the influence of the accompanied tempering process during industrial coating process on the distribution of alloying elements using atom probe tomography. Unlike findings for the fully martensitic steels, no martensite islands with all 24 Kurdjumov-Sachs variants have been observed. Almost all martensite islands contain only one main packet with all six variants and minor variants from the remaining three packets of the same prior austenite grain. Similarly, the martensite bands are typically composed of connected domains originating from prior austenite grains, each containing one main packets (mostly with all variants) and few separate variants. The effect of tempering at similar to 450 degrees C (due to the industrial zinc coating process) has also been investigated. The results show a strong carbon partitioning to lath boundaries and Cottrell atmospheres at dislocation core regions due to the thermal process of coating. In contrast, auto-tempering contributes to the carbon redistribution only in a limited manner. The substitutional elements are all homogenously distributed. The phase transformation process has two effects on the material: mechanically, the earlier-formed laths are larger and softer and therefore more ductile (as revealed by nanoindentation); chemically, due to the higher dislocation density inside the later-formed laths, which are generally smaller, carbon Cottrell atmospheres are predominantly observed. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
New York |
Editor |
|
| Language |
|
Wos |
000431469300044 |
Publication Date |
2018-03-09 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
1044-5803 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
2.714 |
Times cited |
|
Open Access |
Not_Open_Access |
| Notes |
|
Approved |
Most recent IF: 2.714 |
| Call Number |
UA @ lucian @ c:irua:151554 |
Serial |
5033 |
| Permanent link to this record |
| |
|
| |
| Author |
Radi, A.; Khalil-Allafi, J.; Etminanfar, M.R.; Pourbabak, S.; Schryvers, D.; Amin-Ahmadi, B. |
| Title |
Influence of stress aging process on variants of nano-N4Ti3precipitates and martensitic transformation temperatures in NiTi shape memory alloy |
Type |
A1 Journal article |
| Year |
2018 |
Publication |
Materials & design |
Abbreviated Journal |
Mater Design |
| Volume |
262 |
Issue |
262 |
Pages |
74-81 |
| Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
| Abstract |
In this study, the effect of a stress aging process on the microstructure and martensitic phase transformation of NiTi shape memory alloy has been investigated. NiTi samples were aged at 450 degrees C for 1 h and 5 h under different levels of external tensile stress of 15, 60 and 150 MPa. Transmission electron microscopy (TEM) was used to characterize different variants and morphology of precipitates. The results show that application of all stress levels restricts the formation of precipitates variants in the microstructure after I h stress aging process. However, all variants can be detected by prolonging aging time to 5 h at 15 MPa stress level and the variants formation is again restricted by increasing the stress level. Moreover, the stress aging process resulted in changing the shape of precipitates in comparison with that of the stress-free aged samples. Coffee-bean shaped morphologies were detected for precipitates in all stress levels. According to the Differential Scanning Calorimetry (DSC) results, the martensite start temperature (M-s) on cooling shifts to higher temperatures with increasing the tensile stress during the aging process. This can be related to the change ofaustenite to martensite interface energy due to the different volume fractions and variants of precipitates. (c) 2018 Elsevier Ltd. All rights reserved. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
|
Publication Date |
2018-01-04 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
0264-1275 |
ISBN |
|
Additional Links |
UA library record; ; WoS full record; WoS citing articles |
| Impact Factor |
4.364 |
Times cited |
|
Open Access |
OpenAccess |
| Notes |
|
Approved |
Most recent IF: 4.364 |
| Call Number |
UA @ lucian @ c:irua:149854 |
Serial |
4938 |
| Permanent link to this record |
| |
|
| |
| Author |
Cao, M.; Xiong, D.-B.; Tan, Z.; Ji, G.; Amin-Ahmadi, B.; Guo, Q.; Fan, G.; Guo, C.; Li, Z.; Zhang, D. |
| Title |
Aligning graphene in bulk copper : nacre-inspired nanolaminated architecture coupled with in-situ processing for enhanced mechanical properties and high electrical conductivity |
Type |
A1 Journal article |
| Year |
2017 |
Publication |
Carbon |
Abbreviated Journal |
|
| Volume |
117 |
Issue |
|
Pages |
65-74 |
| Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
| Abstract |
Methods used to strengthen metals generally also cause a pronounced decrease in ductility and electrical conductivity. In this work a bioinspired strategy is applied to surmount the dilemma. By assembling copper submicron flakes cladded with in-situ grown graphene, graphene/copper matrix composites with a nanolaminated architecture inspired by a natural nacre have been prepared. Owing to a combined effect-from the bioinspired nanolaminated architecture and improved interfacial bonding, a synergy has been achieved between mechanical strength and ductility as well as electrical conductivity in the graphene/copper matrix composites. With a low volume fraction of only 2.5% of graphene, the composite shows a yield strength and elastic modulus similar to 177% and similar to 25% higher than that of unreinforced copper matrix, respectively, while retains ductility and electrical conductivity comparable to that of pure copper. The bioinspired nanolaminated architecture enhances the efficiencies of two-dimensional (2D) graphene in mechanical strengthening and electrical conducting by aligning graphene to maximize performance for required loading and carrier transporting conditions, and toughens the composites by crack deflection. Meanwhile, in-situ growth of graphene is beneficial for improving interfacial bonding and structural quality of graphene. The strategy sheds light on the development of composites with good combined structural and functional properties. (C) 2017 Elsevier Ltd. All rights reserved. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000400212100008 |
Publication Date |
2017-02-27 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
0008-6223 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
|
Times cited |
|
Open Access |
|
| Notes |
|
Approved |
no |
| Call Number |
UA @ admin @ c:irua:152635 |
Serial |
7435 |
| Permanent link to this record |
| |
|
| |
| Author |
Schouteden, K.; Amin-Ahmadi, B.; Li, Z.; Muzychenko, D.; Schryvers, D.; Van Haesendonck, C. |
| Title |
Electronically decoupled stacking fault tetrahedra embedded in Au(111) films |
Type |
A1 Journal article |
| Year |
2016 |
Publication |
Nature communications |
Abbreviated Journal |
Nat Commun |
| Volume |
7 |
Issue |
7 |
Pages |
14001 |
| Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
| Abstract |
Stacking faults are known as defective structures in crystalline materials that typically lower the structural quality of the material. Here, we show that a particular type of defects, i.e., stacking fault tetrahedra (SFTs), exhibits quantized, particle-in-a-box electronic behaviour, revealing a potential synthetic route to decoupled nanoparticles in metal films. We report on the electronic properties of SFTs that exist in Au(111) films, as evidenced by scanning tunnelling microscopy and confirmed by transmission electron microscopy. We find that the SFTs reveal a remarkable decoupling from their metal surroundings, leading to pronounced energy level quantization effects within the SFTs. The electronic behaviour of the SFTs can be described well by the particle-in-a-box model. Our findings demonstrate that controlled preparation of SFTs may offer an alternative way to achieve well decoupled nanoparticles of high crystalline quality in metal thin films without the need of thin insulating layers. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000390367700001 |
Publication Date |
2016-12-23 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
2041-1723 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
12.124 |
Times cited |
7 |
Open Access |
|
| Notes |
The research in Leuven has been supported by the Research Foundation – Flanders (FWO, Belgium), and by the Flemish Concerted Research Action program (BOF KU Leuven, Project No. GOA/14/007). Z.L. acknowledges the support from the China Scholarship Council (No. 2011624021) and from Internal Funds KU Leuven. K.S. acknowledges additional support from the FWO. The research in Moscow has been supported by grants of the Russian Foundation for Basic Research (RFBR). |
Approved |
Most recent IF: 12.124 |
| Call Number |
EMAT @ emat @ c:irua:138983 |
Serial |
4336 |
| Permanent link to this record |
| |
|
| |
| Author |
Yao, X.; Amin-Ahmadi, B.; Li, Y.; Cao, S.; Ma, X.; Zhang, X.-P.; Schryvers, D. |
| Title |
Optimization of Automated Crystal Orientation Mapping in a TEM for Ni4Ti3 Precipitation in All-Round SMA |
Type |
A1 Journal article |
| Year |
2016 |
Publication |
Shape memory and superelasticity |
Abbreviated Journal |
Shap Mem Superelasticity |
| Volume |
2 |
Issue |
2 |
Pages |
286-297 |
| Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
| Abstract |
Automated crystal orientation and phase mapping in TEM are applied to the quantification of Ni4Ti3 precipitates in Ni–Ti shape memory alloys which will be used for the implantation of artificial sphincters operating using the all-round shape memory effect. This paper focuses on the optimization process of the technique to obtain best values for all major parameters in the acquisition of electron diffraction patterns as well as template generation. With the obtained settings, vast statistical data on nano- and microstructures essential to the operation of these shape memory devices become available. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000408743700001 |
Publication Date |
2016-11-07 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
2199-384X |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
|
Times cited |
2 |
Open Access |
|
| Notes |
X. Yao gratefully acknowledges the Chinese Scholarship Council (CSC) for providing a PhD scholarship. Research support was also provided by the Key Project of the Natural Science Foundation of Guangdong Province (S2013020012805) and the Natural Science Foundation of China under Grant No. 51401081. |
Approved |
Most recent IF: NA |
| Call Number |
EMAT @ emat @ c:irua:138600 |
Serial |
4324 |
| Permanent link to this record |
| |
|
| |
| Author |
Amin-Ahmadi, B.; Connétable, D.; Fivel, M.; Tanguy, D.; Delmelle, R.; Turner, S.; Malet, L.; Godet, S.; Pardoen, T.; Proost, J.; Schryvers, D.; Idrissi, H. |
| Title |
Dislocation/hydrogen interaction mechanisms in hydrided nanocrystalline palladium films |
Type |
A1 Journal article |
| Year |
2016 |
Publication |
Acta materialia |
Abbreviated Journal |
Acta Mater |
| Volume |
111 |
Issue |
111 |
Pages |
253-261 |
| Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
| Abstract |
The nanoscale plasticity mechanisms activated during hydriding cycles in sputtered nanocrystalline Pd films have been investigated ex-situ using advanced transmission electron microscopy techniques. The internal stress developing within the films during hydriding has been monitored in-situ. Results showed that in Pd films hydrided to β-phase, local plasticity was mainly controlled by dislocation activity in spite of the small grain size. Changes of the grain size distribution and the crystallographic texture have not been observed. In contrast, significant microstructural changes were not observed in Pd films hydrided to α-phase. Moreover, the effect of hydrogen loading on the nature and density of dislocations has been investigated using aberration-corrected TEM. Surprisingly, a high density of shear type stacking faults has been observed after dehydriding, indicating a significant effect of hydrogen on the nucleation energy barriers of Shockley partial dislocations. Ab-initio calculations of the effect of hydrogen on the intrinsic stable and unstable stacking fault energies of palladium confirm the experimental observations. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000375812100027 |
Publication Date |
2016-04-06 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
1359-6454 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
5.301 |
Times cited |
14 |
Open Access |
|
| Notes |
This work was carried out in the framework of the IAP program of the Belgian State Federal Office for Scientific, Technical and Cultural Affairs, under Contract No. P7/21. The support of the FWO research project G012012N “Understanding nanocrystalline mechanical behaviour from structural investigations” for B. Amin-Ahmadi is also gratefully acknowledged. This work was granted access to the HPC resources of CALMIP (CICT Toulouse, France) under the allocations 2014-p0912 and 2014-p0749. |
Approved |
Most recent IF: 5.301 |
| Call Number |
c:irua:132678 |
Serial |
4054 |
| Permanent link to this record |
| |
|
| |
| Author |
Pardoen, T.; Colla, M.-S.; Idrissi, H.; Amin-Ahmadi, B.; Wang, B.; Schryvers, D.; Bhaskar, U.K.; Raskin, J.-P. |
| Title |
A versatile lab-on-chip test platform to characterize elementary deformation mechanisms and electromechanical couplings in nanoscopic objects |
Type |
A1 Journal article |
| Year |
2016 |
Publication |
Comptes rendus : physique |
Abbreviated Journal |
Cr Phys |
| Volume |
17 |
Issue |
17 |
Pages |
485-495 |
| Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
| Abstract |
A nanomechanical on-chip test platform has recently been developed to deform under a variety of loading conditions freestanding thin films, ribbons and nanowires involving submicron dimensions. The lab-on-chip involves thousands of elementary test structures from which the elastic modulus, strength, strain hardening, fracture, creep properties can be extracted. The technique is amenable to in situ transmission electron microscopy (TEM) investigations to unravel the fundamental underlying deformation and fracture mechanisms that often lead to size-dependent effects in small-scale samples. The method allows addressing electrical and magnetic couplings as well in order to evaluate the impact of large mechanical stress levels on different solid-state physics phenomena. We had the chance to present this technique in details to Jacques Friedel in 2012 who, unsurprisingly, made a series of critical and very relevant suggestions. In the spirit of his legacy, the paper will address both mechanics of materials related phenomena and couplings with solids state physics issues. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000373524300020 |
Publication Date |
2015-12-01 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
1631-0705 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
2.048 |
Times cited |
7 |
Open Access |
|
| Notes |
This research has been performed with the financial support of the “Politique scientifique fédérale” under the framework of the interuniversity attraction poles program, IAP7/21, as well as with the support of the “Communauté française de Belgique” under the program “Actions de recherche concertées” ARC 05/10-330 and ARC Convention No. 11/16-037. The support of the “Fonds belge pour la recherche dans l'industrie et l'agriculture (FRIA)” for M.-S. Colla is also gratefully acknowledged as are the FWO research projects G012012N “Understanding nanocrystalline mechanical behavior from structural investigations” for B. Amin-Ahmadi. |
Approved |
Most recent IF: 2.048 |
| Call Number |
c:irua:129995 |
Serial |
4014 |
| Permanent link to this record |
| |
|
| |
| Author |
Gong, X.; Marmy, P.; Volodin, A.; Amin-Ahmadi, B.; Qin, L.; Schryvers, D.; Gavrilov, S.; Stergar, E.; Verlinden, B.; Wevers, M.; Seefeldt, M. |
| Title |
Multiscale investigation of quasi-brittle fracture characteristics in a 9Cr–1Mo ferritic–martensitic steel embrittled by liquid lead–bismuth under low cycle fatigue |
Type |
A1 Journal article |
| Year |
2016 |
Publication |
Corrosion science |
Abbreviated Journal |
|
| Volume |
102 |
Issue |
102 |
Pages |
137-152 |
| Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
| Abstract |
Liquid metal embrittlement (LME) induced quasi-brittle fracture characteristics of a 9Cr–1Mo ferritic–martensitic steel (T91) after fatigue cracking in lead–bismuth eutectic (LBE) have been investigated at various length scales. The results show that the LME fracture morphology is primarily characterized by quasi-brittle translath flat regions partially covered by nanodimples, shallow secondary cracks propagating along the martensitic lath boundaries as well as tear ridges covered by micro dimples. These diverse LME fracture features likely indicate a LME mechanism involving multiple physical processes, such as weakening induced interatomic decohesion at the crack tip and plastic shearing induced nano/micro voiding in the plastic zone. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000367275700014 |
Publication Date |
2015-10-22 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
0010938X |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
|
Times cited |
16 |
Open Access |
|
| Notes |
The work is financially supported by the MYRRHA project,SCK•CEN, Belgium and partly funded by the European AtomicEnergy Community’s (Euratom) Seventh Framework ProgrammeFP7/2007-2013 under grant agreement No. 604862 (MatISSEproject) and in the framework of the EERA (European EnergyResearch Alliance) Joint Programme on Nuclear Materials. Dr. TomVan der Donck (KU Leuven) is acknowledged for the EBSD mea-surements. The authors are grateful to Dr. Van Renterghem Wouter(SCK•CEN) for fruitful discussion of the TEM results. Xing Gongsincerely acknowledges valuable suggestions from Dr. S.P. Lynch(Defence Science and Technology Organisation and Monash Uni-versity, Melbourne, Australia). |
Approved |
Most recent IF: NA |
| Call Number |
c:irua:129997 |
Serial |
4013 |
| Permanent link to this record |
| |
|
| |
| Author |
Delmelle, R.; Amin-Ahmadi, B.; Sinnaeve, M.; Idrissi, H.; Pardoen, T.; Schryvers, D.; Proost, J. |
| Title |
Effect of structural defects on the hydriding kinetics of nanocrystalline Pd thin films |
Type |
A1 Journal article |
| Year |
2015 |
Publication |
International journal of hydrogen energy |
Abbreviated Journal |
Int J Hydrogen Energ |
| Volume |
40 |
Issue |
40 |
Pages |
7335-7347 |
| Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
| Abstract |
While the microstructure of a metal is well-known to affect its equilibrium hydrogen uptake and therefore the hydriding thermodynamics, microstructural effects on the hydriding kinetics are much less documented. Moreover, for thin film systems, such microstructural effects are difficult to separate from the internal stress effect, since most defects generate internal stresses. Such a decoupling has been achieved in this paper for nanocrystalline Pd thin film model systems through the use of a high-resolution, in-situ curvature measurement set-up during Pd deposition, annealing and hydriding. This set-up allowed producing Pd thin films with similar internal stress levels but significantly different microstructures. This was evidenced from detailed defect statistics obtained by transmission electron microscopy, which showed that the densities of grain boundaries, dislocations and twin boundaries have all been lowered by annealing. The same set-up was then used to study the hydriding equilibrium and kinetic behaviour of the resulting films at room temperature. A full quantitative analysis of their hydriding cycles showed that the rate constants of both the adsorption- and absorption-limited kinetic regimes were strongly affected by microstructure. Defect engineering was thereby shown to increase the rate constants for hydrogen adsorption and absorption in Pd by a factor 40 and 30, respectively. Copyright (C) 2015, Hydrogen Energy Publications, LLC. Published by Elsevier Ltd. All rights reserved. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
Oxford |
Editor |
|
| Language |
|
Wos |
000355884300012 |
Publication Date |
2015-05-02 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
0360-3199; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
3.582 |
Times cited |
13 |
Open Access |
|
| Notes |
Iap 7/21 |
Approved |
Most recent IF: 3.582; 2015 IF: 3.313 |
| Call Number |
c:irua:126429 |
Serial |
838 |
| Permanent link to this record |
| |
|
| |
| Author |
Samani, M.K.; Ding, X.Z.; Khosravian, N.; Amin-Ahmadi, B.; Yi, Y.; Chen, G.; Neyts, E.C.; Bogaerts, A.; Tay, B.K. |
| Title |
Thermal conductivity of titanium nitride/titanium aluminum nitride multilayer coatings deposited by lateral rotating cathode arc |
Type |
A1 Journal article |
| Year |
2015 |
Publication |
Thin solid films : an international journal on the science and technology of thin and thick films |
Abbreviated Journal |
Thin Solid Films |
| Volume |
578 |
Issue |
578 |
Pages |
133-138 |
| Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT); Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) |
| Abstract |
A seriesof [TiN/TiAlN]nmultilayer coatingswith different bilayer numbers n=5, 10, 25, 50, and 100 were deposited on stainless steel substrate AISI 304 by a lateral rotating cathode arc technique in a flowing nitrogen atmosphere. The composition and microstructure of the coatings have been analyzed by using energy dispersive X-ray spectroscopy, X-ray diffraction (XRD), and conventional and high-resolution transmission electron microscopy (HRTEM). XRD analysis shows that the preferential orientation growth along the (111) direction is reduced in the multilayer coatings. TEM analysis reveals that the grain size of the coatings decreases with increasing bilayer number. HRTEMimaging of the multilayer coatings shows a high density misfit dislocation between the TiN and TiAlN layers. The cross-plane thermal conductivity of the coatings was measured by a pulsed photothermal reflectance technique. With increasing bilayer number, the multilayer coatings' thermal conductivity decreases gradually. This reduction of thermal conductivity can be ascribed to increased phonon scattering due to the disruption of columnar structure, reduced preferential orientation, decreased grain size of the coatings and present misfit dislocations at the interfaces. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
Lausanne |
Editor |
|
| Language |
|
Wos |
000351686500019 |
Publication Date |
2015-02-21 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
0040-6090; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
1.879 |
Times cited |
41 |
Open Access |
|
| Notes |
|
Approved |
Most recent IF: 1.879; 2015 IF: 1.759 |
| Call Number |
c:irua:125517 |
Serial |
3626 |
| Permanent link to this record |
| |
|
| |
| Author |
Colla, M.-S.; Amin-Ahmadi, B.; Idrissi, H.; Malet, L.; Godet, S.; Raskin, J.-P.; Schryvers, D.; Pardoen, T. |
| Title |
Dislocation-mediated relaxation in nanograined columnar palladium films revealed by on-chip time-resolved HRTEM testing |
Type |
A1 Journal article |
| Year |
2015 |
Publication |
Nature communications |
Abbreviated Journal |
Nat Commun |
| Volume |
6 |
Issue |
6 |
Pages |
5922 |
| Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
| Abstract |
The high-rate sensitivity of nanostructured metallic materials demonstrated in the recent literature is related to the predominance of thermally activated deformation mechanisms favoured by a large density of internal interfaces. Here we report time-resolved high-resolution electron transmission microscopy creep tests on thin nanograined films using on-chip nanomechanical testing. Tests are performed on palladium, which exhibited unexpectedly large creep rates at room temperature. Despite the small 30-nm grain size, relaxation is found to be mediated by dislocation mechanisms. The dislocations interact with the growth nanotwins present in the grains, leading to a loss of coherency of twin boundaries. The density of stored dislocations first increases with applied deformation, and then decreases with time to drive additional deformation while no grain boundary mechanism is observed. This fast relaxation constitutes a key issue in the development of various micro- and nanotechnologies such as palladium membranes for hydrogen applications. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000348742300002 |
Publication Date |
2015-01-05 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
2041-1723; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
12.124 |
Times cited |
34 |
Open Access |
|
| Notes |
Iap7/21; Fwo G012012n |
Approved |
Most recent IF: 12.124; 2015 IF: 11.470 |
| Call Number |
c:irua:122045 |
Serial |
731 |
| Permanent link to this record |
| |
|
| |
| Author |
Amin-Ahmadi, B. |
| Title |
Adanced TEM investigation of the elementary plsticity mechanisms in palladium thin films at the nano scale |
Type |
Doctoral thesis |
| Year |
2015 |
Publication |
|
Abbreviated Journal |
|
| Volume |
|
Issue |
|
Pages |
|
| Keywords |
Doctoral thesis; Electron microscopy for materials research (EMAT) |
| Abstract |
|
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
Antwerpen |
Editor |
|
| Language |
|
Wos |
|
Publication Date |
0000-00-00 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
|
ISBN |
|
Additional Links |
UA library record |
| Impact Factor |
|
Times cited |
|
Open Access |
|
| Notes |
|
Approved |
Most recent IF: NA |
| Call Number |
UA @ lucian @ c:irua:125236 |
Serial |
56 |
| Permanent link to this record |
| |
|
| |
| Author |
Idrissi, H.; Kobler, A.; Amin-Ahmadi, B.; Coulombier, M.; Galceran, M.; Raskin, J.-P.; Godet, S.; Kuebel, C.; Pardoen, T.; Schryvers, D. |
| Title |
Plasticity mechanisms in ultrafine grained freestanding aluminum thin films revealed by in-situ transmission electron microscopy nanomechanical testing |
Type |
A1 Journal article |
| Year |
2014 |
Publication |
Applied physics letters |
Abbreviated Journal |
Appl Phys Lett |
| Volume |
104 |
Issue |
10 |
Pages |
101903 |
| Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
| Abstract |
In-situ bright field transmission electron microscopy (TEM) nanomechanical tensile testing and in-situ automated crystallographic orientation mapping in TEM were combined to unravel the elementary mechanisms controlling the plasticity of ultrafine grained Aluminum freestanding thin films. The characterizations demonstrate that deformation proceeds with a transition from grain rotation to intragranular dislocation glide and starvation plasticity mechanism at about 1% deformation. The grain rotation is not affected by the character of the grain boundaries. No grain growth or twinning is detected. (C) 2014 AIP Publishing LLC. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
American Institute of Physics |
Place of Publication |
New York, N.Y. |
Editor |
|
| Language |
|
Wos |
000333082800022 |
Publication Date |
2014-03-12 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
0003-6951;1077-3118; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
3.411 |
Times cited |
24 |
Open Access |
|
| Notes |
|
Approved |
Most recent IF: 3.411; 2014 IF: 3.302 |
| Call Number |
UA @ lucian @ c:irua:116866 |
Serial |
2649 |
| Permanent link to this record |
| |
|
| |
| Author |
Idrissi, H.; Amin-Ahmadi, B.; Wang, B.; Schryvers, D. |
| Title |
Review on TEM analysis of growth twins in nanocrystalline palladium thin films : toward better understanding of twin-related mechanisms in high stacking fault energy metals |
Type |
A1 Journal article |
| Year |
2014 |
Publication |
Physica status solidi: B: basic research |
Abbreviated Journal |
Phys Status Solidi B |
| Volume |
251 |
Issue |
6 |
Pages |
1111-1124 |
| Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
| Abstract |
Various modes of transmission electron microscopy including aberration corrected imaging were used in order to unravel the fundamental mechanisms controlling the formation of growth twins and the evolution of twin boundaries under mechanical and hydrogen loading modes in nanocrystalline (nc) palladium thin films. The latter were produced by electron-beam evaporation and sputter deposition and subjected to uniaxial tensile deformation as well as hydriding/dehydriding cycles. The results show that the twins form by dissociation of grain boundaries. The coherency of Σ3{111} coherent twin boundaries considerably decreases with deformation due to dislocation/twin boundary interactions while Σ3{112} incoherent twin boundaries dissociate under hydrogen cycling into two-phase boundaries bounding a new and unstable 9R phase. The effect of these elementary mechanisms on the macroscopic behavior of the palladium films is discussed and compared to recent experimental and simulation works in the literature. The results provide insightful information to guide the production of well-controlled population of growth twins in high stacking fault energy nc metallic thin films. The results also indicate directions for further enhancement of the mechanical properties of palladium films as needed for instance in palladium-based membranes in hydrogen applications. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
Berlin |
Editor |
|
| Language |
|
Wos |
000337608600001 |
Publication Date |
2014-02-17 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
0370-1972; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
1.674 |
Times cited |
7 |
Open Access |
|
| Notes |
Iap P7/21; Fwo G012012n |
Approved |
Most recent IF: 1.674; 2014 IF: 1.489 |
| Call Number |
UA @ lucian @ c:irua:114580 |
Serial |
2905 |
| Permanent link to this record |
| |
|
| |
| Author |
Amin-Ahmadi, B.; Idrissi, H.; Galceran, M.; Colla, M.S.; Raskin, J.P.; Pardoen, T.; Godet, S.; Schryvers, D. |
| Title |
Effect of deposition rate on the microstructure of electron beam evaporated nanocrystalline palladium thin films |
Type |
A1 Journal article |
| Year |
2013 |
Publication |
Thin solid films : an international journal on the science and technology of thin and thick films |
Abbreviated Journal |
Thin Solid Films |
| Volume |
539 |
Issue |
|
Pages |
145-150 |
| Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
| Abstract |
The influence of the deposition rate on the formation of growth twins in nanocrystalline Pd films deposited by electron beam evaporation is investigated using transmission electron microscopy. Statistical measurements prove that twin boundary (TB) density and volume fraction of grains containing twins increase with increasing deposition rate. A clear increase of the dislocation density was observed for the highest deposition rate of 5 Å/s, caused by the increase of the internal stress building up during deposition. Based on crystallographic orientation indexation using transmission electron microscopy, it can be concluded that a {111} crystallographic texture increases with increasing deposition rate even though the {101} crystallographic texture remains dominant. Most of the TBs are fully coherent without any residual dislocations. However, for the highest deposition rate (5 Å/s), the coherency of the TBs decreases significantly as a result of the interaction of lattice dislocations emitted during deposition with the growth TBs. The analysis of the grain boundary character of different Pd films shows that an increasing fraction of high angle grain boundaries with misorientation angles around 5565° leads to a higher potential for twin formation. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
Lausanne |
Editor |
|
| Language |
|
Wos |
000321111100025 |
Publication Date |
2013-05-25 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
0040-6090; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
1.879 |
Times cited |
13 |
Open Access |
|
| Notes |
Fwo |
Approved |
Most recent IF: 1.879; 2013 IF: 1.867 |
| Call Number |
UA @ lucian @ c:irua:109268 |
Serial |
807 |
| Permanent link to this record |
| |
|
| |
| Author |
Wang, X.; Amin-Ahmadi, B.; Schryvers, D.; Verlinden, B.; Van Humbeeck, J. |
| Title |
Effect of annealing on the transformation behavior and mechanical properties of two nanostructured Ti-50.8at.%Ni thin wires produced by different methods |
Type |
A1 Journal article |
| Year |
2013 |
Publication |
Materials science forum |
Abbreviated Journal |
|
| Volume |
738/739 |
Issue |
|
Pages |
306-310 |
| Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
| Abstract |
A Ti-50.8at.%Ni wire produced using a co-drawing method and a commercial Ti-50.8at.%Ni wire were annealed at different temperatures between 450°C and 700°C. Grains with diameter less than 100nm were revealed by transmission electron microscopy for both wires before annealing treatment. However, the microstructural heterogeneity of the co-drawn wire is more obvious than that of the commercial wire. Multi-stage martensitic transformation was observed in the co-drawn wire, compared with the one-stage A↔M transformation in the commercial wire after annealing at 600°C for 30min. The differences of total elongation, plateau strain and pseudoelastic recoverable strain between the commercial wire and the co-drawn wire were also observed. The differences of the transformation behavior and mechanical properties between the commercial wire and the co-drawn wire are attributed to the microstructural difference between these two wires. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
Lausanne |
Editor |
|
| Language |
|
Wos |
000316089000055 |
Publication Date |
2013-03-11 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
1662-9752; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
|
Times cited |
5 |
Open Access |
|
| Notes |
|
Approved |
Most recent IF: NA |
| Call Number |
UA @ lucian @ c:irua:104691 |
Serial |
798 |
| Permanent link to this record |
| |
|
| |
| Author |
Amin-Ahmadi, B.; Idrissi, H.; Delmelle, R.; Pardoen, T.; Proost, J.; Schryvers, D. |
| Title |
High resolution transmission electron microscopy characterization of fcc -> 9R transformation in nanocrystalline palladium films due to hydriding |
Type |
A1 Journal article |
| Year |
2013 |
Publication |
Applied physics letters |
Abbreviated Journal |
Appl Phys Lett |
| Volume |
102 |
Issue |
7 |
Pages |
071911-71914 |
| Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
| Abstract |
Sputtered nanocrystalline palladium thin films with nanoscale growth twins have been subjected to hydriding cycles. The evolution of the twin boundaries has been investigated using high resolution transmission electron microscopy. Surprisingly, the Sigma 3{112} incoherent twin boundaries dissociate after hydriding into two phase boundaries bounding a 9R phase. This phase which corresponds to single stacking faults located every three {111} planes in the fcc Pd structure was not expected because of the high stacking fault energy of Pd. This observation is connected to the influence of the Hydrogen on the stacking fault energy of palladium and the high compressive stresses building up during hydriding. (C) 2013 American Institute of Physics. [http://dx.doi.org/10.1063/1.4793512] |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
American Institute of Physics |
Place of Publication |
New York, N.Y. |
Editor |
|
| Language |
|
Wos |
000315596700023 |
Publication Date |
2013-02-26 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
0003-6951; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
3.411 |
Times cited |
14 |
Open Access |
|
| Notes |
Iap |
Approved |
Most recent IF: 3.411; 2013 IF: 3.515 |
| Call Number |
UA @ lucian @ c:irua:108303 |
Serial |
1462 |
| Permanent link to this record |
| |
|
| |
| Author |
Peirs, J.; Tirry, W.; Amin-Ahmadi, B.; Coghe, F.; Verleysen, P.; Rabet, L.; Schryvers, D.; Degrieck, J. |
| Title |
Microstructure of adiabatic shear bands in Ti6Al4V |
Type |
A1 Journal article |
| Year |
2013 |
Publication |
Materials characterization |
Abbreviated Journal |
Mater Charact |
| Volume |
75 |
Issue |
|
Pages |
79-92 |
| Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
| Abstract |
Microstructural deformation mechanisms in adiabatic shear bands in Ti6Al4V are studied using traditional TEM and selected area diffraction, and more advanced microstructural characterisation techniques such as energy dispersive X-ray spectroscopy, high angle annular dark field STEM and conical dark field TEM. The shear bands under investigation are induced in Ti6Al4V samples by high strain rate compression of cylindrical and hat-shaped specimens in a split Hopkinson pressure bar setup. Samples from experiments interrupted at different levels of deformation are used to study the evolution of the microstructure in and nearby the shear bands. From the early stages of adiabatic shear band formation, TEM revealed strongly elongated equiaxed grains in the shear band. These band-like grains become narrower towards the centre of the band and start to fraction even further along their elongated direction to finally result in a nano-crystalline region in the core. In fully developed shear bands, twins and a needle-like martensite morphology are observed near the shear band. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
New York |
Editor |
|
| Language |
|
Wos |
000314860900011 |
Publication Date |
2012-11-07 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
1044-5803; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
2.714 |
Times cited |
56 |
Open Access |
|
| Notes |
Iuap; Fwo |
Approved |
Most recent IF: 2.714; 2013 IF: 1.925 |
| Call Number |
UA @ lucian @ c:irua:105300 |
Serial |
2065 |
| Permanent link to this record |
| |
|
| |
| Author |
Khalil-Allafi, J.; Amin-Ahmadi, B. |
| Title |
Effect of mold hardness on microstructure and contraction porosity in ductile cast iron |
Type |
A1 Journal article |
| Year |
2011 |
Publication |
Journal of iron and steel research international |
Abbreviated Journal |
J Iron Steel Res Int |
| Volume |
18 |
Issue |
4 |
Pages |
44-47 |
| Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
| Abstract |
The effect of mold hardness on the microstructure of ductile iron and the contraction porosity was investigated. Molds with different hardnesses (0.41, 0.48, 0.55, 0.62 MPa) and a sand mold prepared by Co2 method were used. The influence of silicon content on the induced expansion pressure owing to the formation of graphite was also investigated. The contraction during solidification can be compensated by an induced expansion owing to the graphite relief when the hardness of mold increases; therefore, the possibility of achieving a sound product without using any riser increases. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
|
Publication Date |
2011-05-01 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
1006-706X; |
ISBN |
|
Additional Links |
UA library record |
| Impact Factor |
0.836 |
Times cited |
1 |
Open Access |
|
| Notes |
|
Approved |
Most recent IF: 0.836; 2011 IF: 0.213 |
| Call Number |
UA @ lucian @ c:irua:122044 |
Serial |
823 |
| Permanent link to this record |
| |
|
| |
| Author |
Khalil-Allafi, J.; Amin-Ahmadi, B. |
| Title |
Influence of mold preheating and silicon content on microstructure and casting properties of ductile iron in permanent mold |
Type |
A1 Journal article |
| Year |
2011 |
Publication |
Journal of iron and steel research international |
Abbreviated Journal |
J Iron Steel Res Int |
| Volume |
18 |
Issue |
3 |
Pages |
34-39 |
| Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
| Abstract |
The effects of the mold preheating and the silicon content of ductile iron on the percentage of carbides, graphite nodule counts and shrinkage volume were investigated. The results showed that the percentage of carbides and the shrinkage volume decreased when the mold preheating increased. The ductile iron with the carbon equivalent of 4.45% and the silicon content of 2.5% without any porosity defects was achieved when the mold preheating was 450 °C. Increasing the silicon content in the range of 2.1%3.3% led to the increase in graphite nodule count and graphite size and the decrease in percentage of carbides. It is due to the increase in induced expansion pressure during the graphite formation with the increasing of silicon content. The suitable condition for casting a sound product of ductile iron without the riser at the mold preheating temperature of 300 °C is the silicon content of 3.3% and carbon equivalent of 4.7%. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
|
Publication Date |
2011-03-28 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
1006-706X; |
ISBN |
|
Additional Links |
UA library record |
| Impact Factor |
0.836 |
Times cited |
3 |
Open Access |
|
| Notes |
|
Approved |
Most recent IF: 0.836; 2011 IF: 0.213 |
| Call Number |
UA @ lucian @ c:irua:122043 |
Serial |
1629 |
| Permanent link to this record |
| |
|
| |
| Author |
Khalil-Allafi, J.; Amin-Ahmadi, B. |
| Title |
Multiple-step martensitic transformations in the Ni51Ti49 single crystal |
Type |
A1 Journal article |
| Year |
2010 |
Publication |
Journal of materials science |
Abbreviated Journal |
J Mater Sci |
| Volume |
45 |
Issue |
23 |
Pages |
6440-6445 |
| Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
| Abstract |
Multiple-step martensitic transformations of an aged Ni51Ti49 single crystal using calorimetric method were investigated. Results show that for short aging times (1045 min) multiple-step martensitic transformations on cooling occur in two steps. Applying intermediate aging times (1.254 h) results in three steps and long aging times (more than 8 h) lead to two-step martensitic transformations again. This behavior has not been recognized in NiTi single crystals in literatures. It can be related to the heterogeneity of composition and stress fields around Ni4Ti3 precipitates. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
London |
Editor |
|
| Language |
|
Wos |
000282429400021 |
Publication Date |
2010-06-30 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
0022-2461;1573-4803; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
2.599 |
Times cited |
5 |
Open Access |
|
| Notes |
|
Approved |
Most recent IF: 2.599; 2010 IF: 1.859 |
| Call Number |
UA @ lucian @ c:irua:122046 |
Serial |
2231 |
| Permanent link to this record |
| |
|
| |
| Author |
Khalil-Allafi, J.; Amin-Ahmadi, B.; Zare, M. |
| Title |
Biocompatibility and corrosion behavior of the shape memory NiTi alloy in the physiological environments simulated with body fluids for medical applications |
Type |
A1 Journal article |
| Year |
2010 |
Publication |
Materials science and engineering: part C: biomimetic materials |
Abbreviated Journal |
Mat Sci Eng C-Mater |
| Volume |
30 |
Issue |
8 |
Pages |
1112-1117 |
| Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
| Abstract |
Due to unique properties of NiTi shape memory alloys such as high corrosion resistance, biocompatibility, super elasticity and shape memory behavior, NiTi shape memory alloys are suitable materials for medical applications. Although TiO2 passive layer in these alloys can prevent releasing of nickel to the environment, high nickel content and stability of passive layer in these alloys are very debatable subjects. In this study a NiTi shape memory alloy with nominal composition of 50.7 atom% Ni was investigated by corrosion tests. Electrochemical tests were performed in two physiological environments of Ringer solution and NaCl 0.9% solution. Results indicate that the breakdown potential of the NiTi alloy in NaCl 0.9% solution is higher than that in Ringer solution. The results of Scanning Electron Microscope (SEM) reveal that low pitting corrosion occurred in Ringer solution compared with NaCl solution at potentiostatic tests. The pH value of the solutions increases after the electrochemical tests. The existence of hydride products in the X-ray diffraction analysis confirms the decrease of the concentration of hydrogen ion in solutions. Topographical evaluations show that corrosion products are nearly same in all samples. The biocompatibility tests were performed by reaction of mouse fibroblast cells (L929). The growth and development of cells for different times were measured by numbering the cells or statistics investigations. The figures of cells for different times showed natural growth of cells. The different of the cell numbers between the test specimen and control specimen was negligible; therefore it may be concluded that the NiTi shape memory alloy is not toxic in the physiological environments simulated with body fluids. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
Lausanne |
Editor |
|
| Language |
|
Wos |
000282905600006 |
Publication Date |
2010-06-23 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
0928-4931; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
4.164 |
Times cited |
34 |
Open Access |
|
| Notes |
|
Approved |
Most recent IF: 4.164; 2010 IF: 2.180 |
| Call Number |
UA @ lucian @ c:irua:122039 |
Serial |
242 |
| Permanent link to this record |
| |
|
| |
| Author |
Amin-Ahmadi, B.; Aashuri, H. |
| Title |
Semisolid structure for M2 high speed steel prepared by cooling slope |
Type |
A1 Journal article |
| Year |
2010 |
Publication |
Journal of materials processing technology |
Abbreviated Journal |
J Mater Process Tech |
| Volume |
210 |
Issue |
12 |
Pages |
1632-1635 |
| Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
| Abstract |
Effects of cooling slope angle and the temperature of molten metal on the globular structure of M2 high speed steel after holding at the semisolid state have been investigated. The globular structure was achieved by pouring the molten metal at 1595 °C on the ceramic cooling slope with the length of 200 mm and the angle of 25°. The globular structure of M2 high speed steel in the form of rolledannealed and as cast condition after holding at semisolid state has been achieved. The size of globular grains of cooling slope sample was smaller than that of the rolledannealed and as cast samples. Solid particles of rolledannealed sample after holding at semisolid state had better roundness compared with cooling slope sample. Dissolution of carbides in the austenite phase at grain boundaries leads to formation of globular particles in the semisolid state. MC-type and M6C-type eutectic carbides reprecipitate during cooling cycle along grain boundaries. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
Amsterdam |
Editor |
|
| Language |
|
Wos |
000280498200011 |
Publication Date |
2010-06-02 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
0924-0136; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
3.147 |
Times cited |
12 |
Open Access |
|
| Notes |
|
Approved |
Most recent IF: 3.147; 2010 IF: 1.570 |
| Call Number |
UA @ lucian @ c:irua:122042 |
Serial |
2983 |
| Permanent link to this record |
| |
|
| |
| Author |
Amin-Ahmadi, B.; Aashuri, H. |
| Title |
Globular structure of M2 high speed steel by thermomechanical treatment in the semisolid state |
Type |
A1 Journal article |
| Year |
2010 |
Publication |
Steel research international |
Abbreviated Journal |
Steel Res Int |
| Volume |
81 |
Issue |
5 |
Pages |
381-386 |
| Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
| Abstract |
The globular structure of M2 high speed steel in the rolled – annealed and as cast conditions was investigated in the semisolid state. Metallographic observations resulted in globular austenite particles that were surrounded by a liquid phase. Dissolution of various carbides in the austenite phase at semisolid temperatures led to grain boundary liquation and formation of near-spherical solid grains in a liquid matrix. Therefore, at the semisolid state, the solid particles were free from carbides. MC- type and M6C- type eutectic carbides re- precipitated at the grain boundaries during cooling of the samples from the semisolid temperature. The variation of shape factor versus holding time and holding temperature was examined. A transition value for shape factor changes in high speed steels was achieved. The growth rate constants of the Ostwald ripening and the coalescence mechanisms were calculated by using the experimentally determined rate constant. It was observed that less liquid droplets were enclosed inside the solid particles compared with non-ferrous alloys. Besides, it has been shown that at high solid fraction, the Ostwald ripening mechanism plays a prominent role in the coarsening phenomenon in comparison with the coalescence mechanism. Grains can rotate and arrange low misorientation with each other at high liquid contents, therefore low energetic grain boundaries form between these grains. These grain boundaries play an important role in the coalescence mechanism. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
Verlag Stahleisen |
Place of Publication |
Düsseldorf |
Editor |
|
| Language |
|
Wos |
000278292200007 |
Publication Date |
2010-05-18 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
1611-3683;1869-344X; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
1.235 |
Times cited |
1 |
Open Access |
|
| Notes |
|
Approved |
Most recent IF: 1.235; 2010 IF: 0.455 |
| Call Number |
UA @ lucian @ c:irua:122047 |
Serial |
1347 |
| Permanent link to this record |
| |
|
| |
| Author |
Khalil-Allafi, J.; Amin-Ahmadi, B. |
| Title |
The effect of chemical composition on enthalpy and entropy changes of martensitic transformations in binary NiTi shape memory alloys |
Type |
P3 Proceeding |
| Year |
2009 |
Publication |
Journal Of Alloys And Compounds |
Abbreviated Journal |
J Alloy Compd |
| Volume |
487 |
Issue |
|
Pages |
363-366 |
| Keywords |
P3 Proceeding; Condensed Matter Theory (CMT) |
| Abstract |
In the present research work the binary NiTi alloys with various compositions in the range of 50.351 at.% Ni were used. Samples have been annealed at 850 °C for 15 min and then quenched in water. In order to characterize transformation temperatures and enthalpy changes of the forward and the reverse martensitic transformation, Differential Scanning Calorimetric (DSC) experiments were performed. The enthalpy and entropy changes as a function of Ni atomic content have been thermodynamically investigated. Results show that enthalpy and entropy changes of martensitic transformation decrease when Ni atomic content increases. The variation of enthalpy and entropy of martensitic transformation with Ni content in binary NiTi alloys were explained by thermodynamic parameters and electron concentration of alloy (e/a) respectively. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
Amsterdam |
Editor |
|
| Language |
|
Wos |
000272521900073 |
Publication Date |
2009-07-31 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
Proceedings of the 22nd International Conference on the Physics of Semiconductors |
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
0925-8388; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
3.133 |
Times cited |
30 |
Open Access |
|
| Notes |
|
Approved |
Most recent IF: 3.133; 2009 IF: 2.135 |
| Call Number |
UA @ lucian @ c:irua:122040 |
Serial |
804 |
| Permanent link to this record |
