Abstract: The existing River Water Quality Model No. 1 (RWQM1) was extended with processes determining the fate of non-volatile pesticides in the water phase and sediments. The exchange of pesticides between the water column and the sediment is described by three transport processes: diffusion, sedimentation and resuspension. Burial of sediments is also included. The modified model was used to simulate the concentrations of diuron and chloridazon in the river Nil. A good agreement was found between the simulated pesticide concentrations and measured values resulting from a four-month intensive monitoring campaign. The simulation results indicate that pesticide concentrations in the bulk water are not sensitive to the selected biochemical model parameters. it seems that these concentrations are mainly determined by the imposed upstream concentrations, run-off and direct losses. The high concentrations in the bulk water were not observed in the sediment pore water due to a limited exchange between the water column and the sediment. According to a sensitivity analysis, the observed pesticide concentrations are highly sensitive to the diffusion and sorption coefficients. Therefore, model users should determine these parameters with accuracy in order to reduce the degree of uncertainty in their results.

Abstract: Suspended particles and dissolved substances in water provide reactive surfaces, influence metabolic activity and contribute to the net sediment deposition. It therefore plays an important part in the ecology and quality of the water mass. The water quality in reservoirs is crucial and it is naturally maintained by flushing and sedimentation, which continuously remove phosphorus from the water. In some reservoirs, however, these removal processes are countered by recycling of ions which could play a key role to start and/or maintain the eutrophic state. The combination of macro-, trace- and microanalysis techniques can be useful to trace pollution sources through a chemical fingerprint, whether be during an acute environmental disaster or a long-term release of pollutants. The water quality and total metal content of reservoir sediments were assessed in a reservoir, situated in the capital of the Paraná State, in the South-Eastern part of Brazil. The goal of this paper was to determine the metal presence in the sediment and metal and ionic speciation in the Green River reservoir water. Water and bed sediment samples, collected from various sites during 2008 and 2009, were investigated using XRF, ICP-OES, ICP-MS, XRD and zeta potential measurements. Based on the results, the heavy metal concentration and chemical composition of the suspended matter in the water samples, as well as the sediment's chemical composition will be discussed.

Abstract: The Darhib mine is one of the several talc deposits in the Hamata area of southeastern Egypt. Several specimens of minerals coming from this mine were subjected to complementary investigation by micro-Raman spectrometry and scanning electron microscopy. The difficulty in their identification is the appearance of most of them: they are all very small and only visible under the mineral binocular microscope(×10 – ×40). They appear as small crystals in fissures and holes and a visual determination on colour and crystal gives only a guess of what kind of mineral it could be. Therefore, only after analyzing them by micro-Raman and scanning electron microscopy it was possible to identify their structure and they can be divided in three main groups: one is quite generic and several minerals of different species were identified, such as quartz, talc, mottramite and chrysocolla, very common in the talc mine (these ones are Si-based minerals); the other one is constituted by four samples which are Zn and/or Cu rich, which means minerals of the rosasite or aurichalcite groups; the last group is constituted by two samples containing mainly Pb..

Abstract: X-ray radiographic images of paintings often show little or no contrast. In order to increase the contrast in radiographic images we measured the X-ray spectrum of a low power X-ray tube, after passing through the painting, with a high energy-resolution SDD detector. To obtain images, the detector is collimated with a 400 mu m diameter pinhole and the painting was moved through the beam in the x and y-direction using a dwell time of a few seconds per pixel. The data obtained consists of a data cube of, typically, 200 x 200 pixels and a 512-channel X-ray spectrum for each pixel, spanning the energy range from 0 to 40 keV. Having the absorbance spectrum available for each pixel, we are able, a posteriori, to produce images by edge subtraction for any given element. In this way high contrast, element-specific, images can be obtained. Because of the high energy-resolution a much simpler edge subtraction algorithm can be applied. We also used principal-component imaging to obtain, in a more automated way, images with high contrast. Some of these images can easily be attributed to specific elements. It turns out that preprocessing of the spectral data is crucial for the success of the multivariate image processing.

Abstract: The risk profile of Cr and Pb in urban road deposited sediment Exponential urbanisation and industrial growth occur on a global scale and result in an ecological burden, of which one important part is pollution. It is well known that the extent of air pollution has escalated over the past two decades in several parts of the world, despite mitigating measures and legislation. Current research points to the fact that air pollution in urban and industrial areas is substantially different from that found in rural areas. Road dust (RD) contributes up to 35% of airborne particulate matter due to resuspension thereof, and poses a health concern due to carcinogenic and toxic components potentially present in the micron-sized fractions. Although literature does report on the concentrations of trace, toxic metals and metalloids present in RD (Hooker and Nathanail 2006), the molecular make-up of particulates generated due to the resuspension of the RD is not well documented. In vitro and animal toxicological studies have confirmed that the chemical composition of inhaled particles plays a major role in its toxic, genotoxic and carcinogenic mechanisms, but the component-specific toxic effects are still not understood. Transition metals binding to air particle matter can result in reactive oxygen species in the human body (particularly in the lungs), and this is a significant risk, especially for vulnerable population groups like elderly people, children and terminally ill patients. The characterisation of the molecular composition of the fine fraction is evidently of importance for public health. During an earlier study, road dust from an inner-city environment in the UK was collected and partially characterised (Barrett e.a. 2010). These same-size fractions were analysed for their elemental concentrations, using X-ray Fluorescence Spectrometry (XRFS) and Inductively Coupled Plasma Mass Spectrometry (ICP-MS). In addition, single-particle analysis was performed on the different fractions by means of Computer Controlled Electron Probe X-ray Micro Analysis (CC-EPXMA) and their molecular structure probed by studying elemental associations. These findings were correlated with Micro Raman Spectroscopy (MRS) results. It was found that the fine fraction (<38 μm) had the highest Pb (238 ppm) and Cr (171 ppm) concentrations. The CC-EPXMA data showed >50% association of Cr-rich particles with Pb and the MRS data showed that the Cr was mostly present as lead chromate and therefore in the Cr(VI) oxidation state. Concentrations of both Pb and Cr decreased substantially (279 (<38 mm) 13 ppm (<1mm); 171 (<38 mm) 91 ppm (<1mm) respectively) in the larger fractions. Apart from rather alarmingly high concentrations of oxidative stressors (Cu, Fe, Mn), the carcinogenic and toxic potential of the inhalable fraction is evident. Preliminary bioaccessibility data indicated that both Cr and Pb are readily

Abstract: The goal of the present study was to analyze the relationship between the fume formation rate, welding conditions, chemical composition of welding fume particles and their size. In the range from 0.25 to 16 μm aerodynamic diameter, three distinct types of welding fume particles were identified in the welder's breathing zone. The elemental composition of each type depended completely on the used welding materials, and reflects their mechanism of formation. Their relative abundance in the welding fume appeared to be dependent on the electrode coating, as well as the heat input during welding.

Abstract: Simultaneous measurements of ultrafine particles (UFPs) were carried out at four sampling locations situated within a 1 km(2) grid area in a Belgian city, Borgerhout (Antwerp). All sampling sites had different orientation and height of buildings and dissimilar levels of anthropogenic activities (mainly traffic volume). The aims were to investigate: (i) the spatio-temporal variation of UFP within the area, (ii) the effect of wind direction with respect to the volume of traffic on UFP levels, and (iii) the spatial representativeness of the official monitoring station situated in the study area. All sampling sites followed similar diurnal patterns of UFP variation, but effects of local traffic emissions were evident. Wind direction also had a profound influence on UFP concentrations at certain sites. The results indicated a clear influence of local weather conditions and the more dominant effect of traffic volumes. Our analysis indicated that the regional air quality monitoring station represented the other sampling sites in the study area reasonably well; temporal patterns were found to be comparable though the absolute average concentrations showed differences of up to 35%. (C) 2012 Elsevier B.V. All rights reserved.