| |
Records |
Links |
|
Author |
Özen, M.; Mertens, M.; Luyten, J.; Snijkers, F.; d' Hondt, H.; Cool, P. |
|
| |
Title  |
Hydrothermal synthesis of carbonate-free submicron-sized barium titanate from an amorphous precursor : synthesis and characterization |
Type |
A1 Journal article |
| |
Year |
2012 |
Publication |
Ceramics international |
Abbreviated Journal |
Ceram Int |
|
| |
Volume |
38 |
Issue |
1 |
Pages |
619-625 |
|
| |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT); Laboratory of adsorption and catalysis (LADCA) |
|
| |
Abstract |
In this paper, the amorphous barium titanate precursor was prepared by the peroxo-hydroxide method and post-treated by various drying procedures, such as: room temperature drying, room temperature vacuum drying and vacuum drying at 50 degrees C. The objective in the latter two treatments was to increase the Ti-O-Ba bonds of the precursor. The post-treated precursors were compared with the untreated (i.e., 'wet') precursor. Also, a barium titanate precursor was prepared by an alkoxide route. Afterwards, the precursors were hydrothermally treated at 200 degrees C in a 10 M NaOH solution. Vacuum drying of the precursor seemingly promoted the formation of Ti-O-Ti bonds in the hydrothermal end-product. The low Ba:Ti ratio (0.66) of the alkoxide-route prepared precursor lead to a multi-phase hydrothermal product with BaTiO(3) as the main phase. In contrast, phase pure BaTiO(3), i.e. without BaCO(3) contamination, was obtained for the precursor which was dried at room temperature. Cube-shaped and highly crystalline BaTiO(3) particles were observed by electron microscopy for the hydrothermally treated peroxo-hydroxide-route prepared precursor. (C) 2011 Elsevier Ltd and Techna Group S.r.l. All rights reserved. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
Barking |
Editor |
|
|
| |
Language |
|
Wos |
000298766900083 |
Publication Date |
2011-08-02 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
0272-8842; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
2.986 |
Times cited |
14 |
Open Access |
|
|
| |
Notes |
|
Approved |
Most recent IF: 2.986; 2012 IF: 1.789 |
|
| |
Call Number |
UA @ lucian @ c:irua:96263 |
Serial |
1541 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Özen, M.; Mertens, M.; Snijkers, F.; Van Tendeloo, G.; Cool, P. |
|
| |
Title |
Texturing of hydrothermally synthesized BaTiO3 in a strong magnetic field by slip casting |
Type |
A1 Journal article |
| |
Year |
2016 |
Publication |
Ceramics international |
Abbreviated Journal |
Ceram Int |
|
| |
Volume |
42 |
Issue |
42 |
Pages |
5382-5390 |
|
| |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT); Laboratory of adsorption and catalysis (LADCA) |
|
| |
Abstract |
Barium titanate powder was processed by slip casting in a rotating strong magnetic field of 9.4 T. The orientation factor of the sintered compact was analyzed by the X-ray diffraction technique and the microstructure (grain-size) was analyzed by scanning electron microscope. The hydrothermally prepared barium titanate was used as matrix material and the molten-salt synthesized barium titanate, with a larger particle-size, was used as template for the templated grain-growth process. Addition of large template particles was observed to increase the orientation factor of the sintered cast (5 vol% loading). Template particles acted as starting grains for the abnormal grain-growth process and the average grain-size was increased after sintering. Increasing the solid loading (15 vol%) resulted in a similar orientation factor with a decrease of the average grain size by more than half. However, addition of templates to the 15 vol% cast had a negative effect on the orientation factor. The impingement of growing particles was stated as the primary cause of particle misorientation resulting in a low orientation factor after sintering. Different heating conditions were tested and it was determined that a slow heating rate gave the highest orientation factor, the smallest average grain-size and the highest relative density. (C) 2015 Elsevier Ltd and Techna Group S.r.l. All rights reserved. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
Barking |
Editor |
|
|
| |
Language |
|
Wos |
000369460500098 |
Publication Date |
2015-12-23 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
0272-8842 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
2.986 |
Times cited |
11 |
Open Access |
|
|
| |
Notes |
|
Approved |
Most recent IF: 2.986 |
|
| |
Call Number |
UA @ lucian @ c:irua:132228 |
Serial |
4260 |
|
| Permanent link to this record |
